Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC fixes from Olof Johansson:
 "We didn't have any fixes sent up for -rc2, so this is a slightly
  larger batch.  A bit all over the place platform-wise; OMAP, at91,
  marvell, renesas, sunxi, ux500, etc.

  I tried to summarize highlights but there isn't a whole lot to point
  out.  Lots of little things fixed all over.  A couple of defconfig
  updates due to new/changing options."

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
  ARM: at91/sama5: fix incorrect PMC pcr div definition
  ARM: at91/dt: fix macb pinctrl_macb_rmii_mii_alt definition
  ARM: at91: at91sam9n12: move external irq declatation to DT
  ARM: shmobile: marzen: Use error values in usb_power_*
  ARM: tegra: defconfig fixes
  ARM: nomadik: fix IRQ assignment for SMC ethernet
  ARM: vt8500: Add missing NULL terminator in dt_compat
  clk: tegra: add ac97 controller clock
  clk: tegra: remove USB from clk init table
  ARM: dts: mvebu: Fix wrong the address reg value for the L2-cache node
  ARM: plat-orion: Fix num_resources and id for ge10 and ge11
  ARM: OMAP2+: hwmod: Remove sysc slave idle and auto idle apis
  SERIAL: OMAP: Remove the slave idle handling from the driver
  ARM: OMAP2+: serial: Remove the un-used slave idle hooks
  ARM: OMAP2+: hwmod-data: UART IP needs software control to manage sidle modes
  ARM: OMAP2+: hwmod: Add a new flag to handle SIDLE in SWSUP only in active
  ARM: OMAP2+: hwmod: Fix sidle programming in _enable_sysc()/_idle_sysc()
  arm: mvebu: fix the 'ranges' property to handle PCIe
  ARM: mvebu: select ARCH_REQUIRE_GPIOLIB for mvebu platform
  ARM: AM33XX: Add missing .clkdm_name to clkdiv32k_ick clock
  ...

Documentation/devicetree/bindings/net/macb.txt

@@ -4,7 +4,7 @@ Required properties:
 - compatible: Should be "cdns,[<chip>-]{macb|gem}"
   Use "cdns,at91sam9260-macb" Atmel at91sam9260 and at91sam9263 SoCs.
   Use "cdns,at32ap7000-macb" for other 10/100 usage or use the generic form: "cdns,macb".
-  Use "cnds,pc302-gem" for Picochip picoXcell pc302 and later devices based on
+  Use "cdns,pc302-gem" for Picochip picoXcell pc302 and later devices based on
   the Cadence GEM, or the generic form: "cdns,gem".
 - reg: Address and length of the register set for the device
 - interrupts: Should contain macb interrupt

arch/arm/boot/dts/Makefile

@@ -177,7 +177,9 @@ dtb-$(CONFIG_ARCH_SPEAR3XX)+= spear300-evb.dtb \
 	spear320-evb.dtb \
 	spear320-hmi.dtb
 dtb-$(CONFIG_ARCH_SPEAR6XX)+= spear600-evb.dtb
-dtb-$(CONFIG_ARCH_SUNXI) += sun4i-a10-cubieboard.dtb \
+dtb-$(CONFIG_ARCH_SUNXI) += \
+	sun4i-a10-cubieboard.dtb \
+	sun4i-a10-mini-xplus.dtb \
 	sun4i-a10-hackberry.dtb \
 	sun5i-a13-olinuxino.dtb
 dtb-$(CONFIG_ARCH_TEGRA) += tegra20-harmony.dtb \

arch/arm/boot/dts/armada-370-xp.dtsi

@@ -33,7 +33,8 @@ soc {
 		#size-cells = <1>;
 		compatible = "simple-bus";
 		interrupt-parent = <&mpic>;
-		ranges = <0 0 0xd0000000 0x100000>;
+		ranges = <0          0 0xd0000000 0x0100000 /* internal registers */
+			  0xe0000000 0 0xe0000000 0x8100000 /* PCIe */>;
 
 		internal-regs {
 			compatible = "simple-bus";

arch/arm/boot/dts/armada-370.dtsi

@@ -29,7 +29,8 @@ aliases {
 	};
 
 	soc {
-		ranges = <0 0xd0000000 0x100000>;
+		ranges = <0          0xd0000000 0x0100000 /* internal registers */
+			  0xe0000000 0xe0000000 0x8100000 /* PCIe */>;
 		internal-regs {
 			system-controller@18200 {
 				compatible = "marvell,armada-370-xp-system-controller";
@@ -38,12 +39,12 @@ system-controller@18200 {
 
 			L2: l2-cache {
 				compatible = "marvell,aurora-outer-cache";
-				reg = <0xd0008000 0x1000>;
+				reg = <0x08000 0x1000>;
 				cache-id-part = <0x100>;
 				wt-override;
 			};
 
-			mpic: interrupt-controller@20000 {
+			interrupt-controller@20000 {
 				reg = <0x20a00 0x1d0>, <0x21870 0x58>;
 			};
 

arch/arm/boot/dts/armada-xp-gp.dts

@@ -39,6 +39,9 @@ memory {
 	};
 
 	soc {
+		ranges = <0          0 0xd0000000 0x100000
+			  0xf0000000 0 0xf0000000 0x1000000>;
+
 		internal-regs {
 			serial@12000 {
 				clock-frequency = <250000000>;

arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts

@@ -27,6 +27,9 @@ memory {
 	};
 
 	soc {
+		ranges = <0          0 0xd0000000 0x100000
+			  0xf0000000 0 0xf0000000 0x8000000>;
+
 		internal-regs {
 			serial@12000 {
 				clock-frequency = <250000000>;

arch/arm/boot/dts/armada-xp.dtsi

@@ -31,7 +31,7 @@ L2: l2-cache {
 				wt-override;
 			};
 
-			mpic: interrupt-controller@20000 {
+			interrupt-controller@20000 {
 			      reg = <0x20a00 0x2d0>, <0x21070 0x58>;
 			};
 

arch/arm/boot/dts/at91sam9260.dtsi

@@ -264,7 +264,7 @@ pinctrl_macb_rmii_mii_alt: macb_rmii_mii-1 {
 						atmel,pins =
 							<0 10 0x2 0x0	/* PA10 periph B */
 							 0 11 0x2 0x0	/* PA11 periph B */
-							 0 24 0x2 0x0	/* PA24 periph B */
+							 0 22 0x2 0x0	/* PA22 periph B */
 							 0 25 0x2 0x0	/* PA25 periph B */
 							 0 26 0x2 0x0	/* PA26 periph B */
 							 0 27 0x2 0x0	/* PA27 periph B */

arch/arm/boot/dts/at91sam9n12.dtsi

@@ -57,6 +57,7 @@ aic: interrupt-controller@fffff000 {
 				compatible = "atmel,at91rm9200-aic";
 				interrupt-controller;
 				reg = <0xfffff000 0x200>;
+				atmel,external-irqs = <31>;
 			};
 
 			ramc0: ramc@ffffe800 {

arch/arm/boot/dts/at91sam9x25ek.dts

@@ -11,7 +11,7 @@
 /include/ "at91sam9x5ek.dtsi"
 
 / {
-	model = "Atmel AT91SAM9G25-EK";
+	model = "Atmel AT91SAM9X25-EK";
 	compatible = "atmel,at91sam9x25ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
 
 	ahb {

arch/arm/boot/dts/omap3.dtsi

@@ -516,7 +516,7 @@ gpmc: gpmc@6e000000 {
 		usb_otg_hs: usb_otg_hs@480ab000 {
 			compatible = "ti,omap3-musb";
 			reg = <0x480ab000 0x1000>;
-			interrupts = <0 92 0x4>, <0 93 0x4>;
+			interrupts = <92>, <93>;
 			interrupt-names = "mc", "dma";
 			ti,hwmods = "usb_otg_hs";
 			multipoint = <1>;

arch/arm/boot/dts/sama5d3.dtsi

@@ -75,11 +75,6 @@ spi0: spi@f0004000 {
 				compatible = "atmel,at91sam9x5-spi";
 				reg = <0xf0004000 0x100>;
 				interrupts = <24 4 3>;
-				cs-gpios = <&pioD 13 0
-					    &pioD 14 0 /* conflicts with SCK0 and CANRX0 */
-					    &pioD 15 0 /* conflicts with CTS0 and CANTX0 */
-					    &pioD 16 0 /* conflicts with RTS0 and PWMFI3 */
-					   >;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_spi0>;
 				status = "disabled";
@@ -156,7 +151,7 @@ usart1: serial@f0020000 {
 			};
 
 			macb0: ethernet@f0028000 {
-				compatible = "cnds,pc302-gem", "cdns,gem";
+				compatible = "cdns,pc302-gem", "cdns,gem";
 				reg = <0xf0028000 0x100>;
 				interrupts = <34 4 3>;
 				pinctrl-names = "default";
@@ -203,11 +198,6 @@ spi1: spi@f8008000 {
 				compatible = "atmel,at91sam9x5-spi";
 				reg = <0xf8008000 0x100>;
 				interrupts = <25 4 3>;
-				cs-gpios = <&pioC 25 0
-					    &pioC 26 0 /* conflitcs with TWD1 and ISI_D11 */
-					    &pioC 27 0 /* conflitcs with TWCK1 and ISI_D10 */
-					    &pioC 28 0 /* conflitcs with PWMFI0 and ISI_D9 */
-					   >;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_spi1>;
 				status = "disabled";

arch/arm/boot/dts/sama5d3xcm.dtsi

@@ -32,6 +32,10 @@ main_clock: clock@0 {
 
 	ahb {
 		apb {
+			spi0: spi@f0004000 {
+				cs-gpios = <&pioD 13 0>, <0>, <0>, <0>;
+			};
+
 			macb0: ethernet@f0028000 {
 				phy-mode = "rgmii";
 			};

arch/arm/boot/dts/ste-nomadik-s8815.dts

@@ -14,13 +14,19 @@ chosen {
 		bootargs = "root=/dev/ram0 console=ttyAMA1,115200n8 earlyprintk";
 	};
 
+	/* This is where the interrupt is routed on the S8815 board */
+	external-bus@34000000 {
+		ethernet@300 {
+			interrupt-parent = <&gpio3>;
+			interrupts = <8 0x1>;
+		};
+	};
+
 	/* Custom board node with GPIO pins to active etc */
 	usb-s8815 {
 		/* The S8815 is using this very GPIO pin for the SMSC91x IRQs */
 		ethernet-gpio {
-			gpios = <&gpio3 19 0x1>;
-			interrupts = <19 0x1>;
-			interrupt-parent = <&gpio3>;
+			gpios = <&gpio3 8 0x1>;
 		};
 		/* This will bias the MMC/SD card detect line */
 		mmcsd-gpio {

arch/arm/boot/dts/sun4i-a10-mini-xplus.dts

@@ -22,8 +22,8 @@ chosen {
 		bootargs = "earlyprintk console=ttyS0,115200";
 	};
 
-	soc {
-		uart0: uart@01c28000 {
+	soc@01c20000 {
+		uart0: serial@01c28000 {
 			pinctrl-names = "default";
 			pinctrl-0 = <&uart0_pins_a>;
 			status = "okay";

arch/arm/configs/omap2plus_defconfig

@@ -20,6 +20,7 @@ CONFIG_MODULE_FORCE_UNLOAD=y
 CONFIG_MODVERSIONS=y
 CONFIG_MODULE_SRCVERSION_ALL=y
 # CONFIG_BLK_DEV_BSG is not set
+CONFIG_ARCH_MULTI_V6=y
 CONFIG_ARCH_OMAP2PLUS=y
 CONFIG_OMAP_RESET_CLOCKS=y
 CONFIG_OMAP_MUX_DEBUG=y

arch/arm/configs/tegra_defconfig

@@ -153,6 +153,7 @@ CONFIG_MEDIA_CAMERA_SUPPORT=y
 CONFIG_MEDIA_USB_SUPPORT=y
 CONFIG_USB_VIDEO_CLASS=m
 CONFIG_DRM=y
+CONFIG_TEGRA_HOST1X=y
 CONFIG_DRM_TEGRA=y
 CONFIG_BACKLIGHT_LCD_SUPPORT=y
 # CONFIG_LCD_CLASS_DEVICE is not set
@@ -202,7 +203,7 @@ CONFIG_TEGRA20_APB_DMA=y
 CONFIG_STAGING=y
 CONFIG_SENSORS_ISL29018=y
 CONFIG_SENSORS_ISL29028=y
-CONFIG_SENSORS_AK8975=y
+CONFIG_AK8975=y
 CONFIG_MFD_NVEC=y
 CONFIG_KEYBOARD_NVEC=y
 CONFIG_SERIO_NVEC_PS2=y

arch/arm/include/debug/ux500.S

@@ -24,9 +24,9 @@
 #define U8500_UART0_PHYS_BASE	(0x80120000)
 #define U8500_UART1_PHYS_BASE	(0x80121000)
 #define U8500_UART2_PHYS_BASE	(0x80007000)
-#define U8500_UART0_VIRT_BASE	(0xa8120000)
-#define U8500_UART1_VIRT_BASE	(0xa8121000)
-#define U8500_UART2_VIRT_BASE	(0xa8007000)
+#define U8500_UART0_VIRT_BASE	(0xf8120000)
+#define U8500_UART1_VIRT_BASE	(0xf8121000)
+#define U8500_UART2_VIRT_BASE	(0xf8007000)
 #define __UX500_PHYS_UART(n)	U8500_UART##n##_PHYS_BASE
 #define __UX500_VIRT_UART(n)	U8500_UART##n##_VIRT_BASE
 #endif

arch/arm/mach-at91/at91rm9200_time.c

@@ -174,6 +174,7 @@ clkevt32k_next_event(unsigned long delta, struct clock_event_device *dev)
 static struct clock_event_device clkevt = {
 	.name		= "at91_tick",
 	.features	= CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
+	.shift		= 32,
 	.rating		= 150,
 	.set_next_event	= clkevt32k_next_event,
 	.set_mode	= clkevt32k_mode,
@@ -264,9 +265,11 @@ void __init at91rm9200_timer_init(void)
 	at91_st_write(AT91_ST_RTMR, 1);
 
 	/* Setup timer clockevent, with minimum of two ticks (important!!) */
+	clkevt.mult = div_sc(AT91_SLOW_CLOCK, NSEC_PER_SEC, clkevt.shift);
+	clkevt.max_delta_ns = clockevent_delta2ns(AT91_ST_ALMV, &clkevt);
+	clkevt.min_delta_ns = clockevent_delta2ns(2, &clkevt) + 1;
 	clkevt.cpumask = cpumask_of(0);
-	clockevents_config_and_register(&clkevt, AT91_SLOW_CLOCK,
-					2, AT91_ST_ALMV);
+	clockevents_register_device(&clkevt);
 
 	/* register clocksource */
 	clocksource_register_hz(&clk32k, AT91_SLOW_CLOCK);

arch/arm/mach-at91/at91sam9n12.c

@@ -223,13 +223,7 @@ static void __init at91sam9n12_map_io(void)
 	at91_init_sram(0, AT91SAM9N12_SRAM_BASE, AT91SAM9N12_SRAM_SIZE);
 }
 
-void __init at91sam9n12_initialize(void)
-{
-	at91_extern_irq = (1 << AT91SAM9N12_ID_IRQ0);
-}
-
 AT91_SOC_START(at91sam9n12)
 	.map_io = at91sam9n12_map_io,
 	.register_clocks = at91sam9n12_register_clocks,
-	.init = at91sam9n12_initialize,
 AT91_SOC_END

arch/arm/mach-at91/include/mach/at91_pmc.h

@@ -179,9 +179,9 @@ extern void __iomem *at91_pmc_base;
 #define		AT91_PMC_PCR_CMD	(0x1  <<  12)		/* Command (read=0, write=1) */
 #define		AT91_PMC_PCR_DIV(n)	((n)  <<  16)		/* Divisor Value */
 #define			AT91_PMC_PCR_DIV0	0x0			/* Peripheral clock is MCK */
-#define			AT91_PMC_PCR_DIV2	0x2			/* Peripheral clock is MCK/2 */
-#define			AT91_PMC_PCR_DIV4	0x4			/* Peripheral clock is MCK/4 */
-#define			AT91_PMC_PCR_DIV8	0x8			/* Peripheral clock is MCK/8 */
+#define			AT91_PMC_PCR_DIV2	0x1			/* Peripheral clock is MCK/2 */
+#define			AT91_PMC_PCR_DIV4	0x2			/* Peripheral clock is MCK/4 */
+#define			AT91_PMC_PCR_DIV8	0x3			/* Peripheral clock is MCK/8 */
 #define		AT91_PMC_PCR_EN		(0x1  <<  28)		/* Enable */
 
 #endif

arch/arm/mach-imx/clk-imx6q.c

@@ -177,7 +177,8 @@ int imx6q_set_lpm(enum mxc_cpu_pwr_mode mode)
 static const char *step_sels[]	= { "osc", "pll2_pfd2_396m", };
 static const char *pll1_sw_sels[]	= { "pll1_sys", "step", };
 static const char *periph_pre_sels[]	= { "pll2_bus", "pll2_pfd2_396m", "pll2_pfd0_352m", "pll2_198m", };
-static const char *periph_clk2_sels[]	= { "pll3_usb_otg", "osc", };
+static const char *periph_clk2_sels[]	= { "pll3_usb_otg", "osc", "osc", "dummy", };
+static const char *periph2_clk2_sels[]	= { "pll3_usb_otg", "pll2_bus", };
 static const char *periph_sels[]	= { "periph_pre", "periph_clk2", };
 static const char *periph2_sels[]	= { "periph2_pre", "periph2_clk2", };
 static const char *axi_sels[]		= { "periph", "pll2_pfd2_396m", "pll3_pfd1_540m", };
@@ -185,7 +186,7 @@ static const char *audio_sels[]	= { "pll4_post_div", "pll3_pfd2_508m", "pll3_pfd
 static const char *gpu_axi_sels[]	= { "axi", "ahb", };
 static const char *gpu2d_core_sels[]	= { "axi", "pll3_usb_otg", "pll2_pfd0_352m", "pll2_pfd2_396m", };
 static const char *gpu3d_core_sels[]	= { "mmdc_ch0_axi", "pll3_usb_otg", "pll2_pfd1_594m", "pll2_pfd2_396m", };
-static const char *gpu3d_shader_sels[] = { "mmdc_ch0_axi", "pll3_usb_otg", "pll2_pfd1_594m", "pll2_pfd9_720m", };
+static const char *gpu3d_shader_sels[] = { "mmdc_ch0_axi", "pll3_usb_otg", "pll2_pfd1_594m", "pll3_pfd0_720m", };
 static const char *ipu_sels[]		= { "mmdc_ch0_axi", "pll2_pfd2_396m", "pll3_120m", "pll3_pfd1_540m", };
 static const char *ldb_di_sels[]	= { "pll5_video", "pll2_pfd0_352m", "pll2_pfd2_396m", "mmdc_ch1_axi", "pll3_usb_otg", };
 static const char *ipu_di_pre_sels[]	= { "mmdc_ch0_axi", "pll3_usb_otg", "pll5_video_div", "pll2_pfd0_352m", "pll2_pfd2_396m", "pll3_pfd1_540m", };
@@ -369,8 +370,8 @@ int __init mx6q_clocks_init(void)
 	clk[pll1_sw]          = imx_clk_mux("pll1_sw",	        base + 0xc,  2,  1, pll1_sw_sels,      ARRAY_SIZE(pll1_sw_sels));
 	clk[periph_pre]       = imx_clk_mux("periph_pre",       base + 0x18, 18, 2, periph_pre_sels,   ARRAY_SIZE(periph_pre_sels));
 	clk[periph2_pre]      = imx_clk_mux("periph2_pre",      base + 0x18, 21, 2, periph_pre_sels,   ARRAY_SIZE(periph_pre_sels));
-	clk[periph_clk2_sel]  = imx_clk_mux("periph_clk2_sel",  base + 0x18, 12, 1, periph_clk2_sels,  ARRAY_SIZE(periph_clk2_sels));
-	clk[periph2_clk2_sel] = imx_clk_mux("periph2_clk2_sel", base + 0x18, 20, 1, periph_clk2_sels,  ARRAY_SIZE(periph_clk2_sels));
+	clk[periph_clk2_sel]  = imx_clk_mux("periph_clk2_sel",  base + 0x18, 12, 2, periph_clk2_sels,  ARRAY_SIZE(periph_clk2_sels));
+	clk[periph2_clk2_sel] = imx_clk_mux("periph2_clk2_sel", base + 0x18, 20, 1, periph2_clk2_sels, ARRAY_SIZE(periph2_clk2_sels));
 	clk[axi_sel]          = imx_clk_mux("axi_sel",          base + 0x14, 6,  2, axi_sels,          ARRAY_SIZE(axi_sels));
 	clk[esai_sel]         = imx_clk_mux("esai_sel",         base + 0x20, 19, 2, audio_sels,        ARRAY_SIZE(audio_sels));
 	clk[asrc_sel]         = imx_clk_mux("asrc_sel",         base + 0x30, 7,  2, audio_sels,        ARRAY_SIZE(audio_sels));
@@ -498,7 +499,7 @@ int __init mx6q_clocks_init(void)
 	clk[ldb_di1]      = imx_clk_gate2("ldb_di1",       "ldb_di1_podf",      base + 0x74, 14);
 	clk[ipu2_di1]     = imx_clk_gate2("ipu2_di1",      "ipu2_di1_sel",      base + 0x74, 10);
 	clk[hsi_tx]       = imx_clk_gate2("hsi_tx",        "hsi_tx_podf",       base + 0x74, 16);
-	clk[mlb]          = imx_clk_gate2("mlb",           "pll8_mlb",          base + 0x74, 18);
+	clk[mlb]          = imx_clk_gate2("mlb",           "axi",               base + 0x74, 18);
 	clk[mmdc_ch0_axi] = imx_clk_gate2("mmdc_ch0_axi",  "mmdc_ch0_axi_podf", base + 0x74, 20);
 	clk[mmdc_ch1_axi] = imx_clk_gate2("mmdc_ch1_axi",  "mmdc_ch1_axi_podf", base + 0x74, 22);
 	clk[ocram]        = imx_clk_gate2("ocram",         "ahb",               base + 0x74, 28);

arch/arm/mach-imx/headsmp.S

@@ -18,8 +18,20 @@
 	.section ".text.head", "ax"
 
 #ifdef CONFIG_SMP
+diag_reg_offset:
+	.word	g_diag_reg - .
+
+	.macro	set_diag_reg
+	adr	r0, diag_reg_offset
+	ldr	r1, [r0]
+	add	r1, r1, r0		@ r1 = physical &g_diag_reg
+	ldr	r0, [r1]
+	mcr	p15, 0, r0, c15, c0, 1	@ write diagnostic register
+	.endm
+
 ENTRY(v7_secondary_startup)
 	bl	v7_invalidate_l1
+	set_diag_reg
 	b	secondary_startup
 ENDPROC(v7_secondary_startup)
 #endif

arch/arm/mach-imx/platsmp.c

@@ -12,6 +12,7 @@
 
 #include <linux/init.h>
 #include <linux/smp.h>
+#include <asm/cacheflush.h>
 #include <asm/page.h>
 #include <asm/smp_scu.h>
 #include <asm/mach/map.h>
@@ -21,6 +22,7 @@
 
 #define SCU_STANDBY_ENABLE	(1 << 5)
 
+u32 g_diag_reg;
 static void __iomem *scu_base;
 
 static struct map_desc scu_io_desc __initdata = {
@@ -80,6 +82,18 @@ void imx_smp_prepare(void)
 static void __init imx_smp_prepare_cpus(unsigned int max_cpus)
 {
 	imx_smp_prepare();
+
+	/*
+	 * The diagnostic register holds the errata bits.  Mostly bootloader
+	 * does not bring up secondary cores, so that when errata bits are set
+	 * in bootloader, they are set only for boot cpu.  But on a SMP
+	 * configuration, it should be equally done on every single core.
+	 * Read the register from boot cpu here, and will replicate it into
+	 * secondary cores when booting them.
+	 */
+	asm("mrc p15, 0, %0, c15, c0, 1" : "=r" (g_diag_reg) : : "cc");
+	__cpuc_flush_dcache_area(&g_diag_reg, sizeof(g_diag_reg));
+	outer_clean_range(__pa(&g_diag_reg), __pa(&g_diag_reg + 1));
 }
 
 struct smp_operations  imx_smp_ops __initdata = {

arch/arm/mach-kirkwood/common.c

@@ -528,12 +528,6 @@ void __init kirkwood_init_early(void)
 {
 	orion_time_set_base(TIMER_VIRT_BASE);
 
-	/*
-	 * Some Kirkwood devices allocate their coherent buffers from atomic
-	 * context. Increase size of atomic coherent pool to make sure such
-	 * the allocations won't fail.
-	 */
-	init_dma_coherent_pool_size(SZ_1M);
 	mvebu_mbus_init("marvell,kirkwood-mbus",
 			BRIDGE_WINS_BASE, BRIDGE_WINS_SZ,
 			DDR_WINDOW_CPU_BASE, DDR_WINDOW_CPU_SZ);

arch/arm/mach-kirkwood/ts219-setup.c

@@ -124,7 +124,7 @@ static void __init qnap_ts219_init(void)
 static int __init ts219_pci_init(void)
 {
 	if (machine_is_ts219())
-		kirkwood_pcie_init(KW_PCIE0);
+		kirkwood_pcie_init(KW_PCIE1 | KW_PCIE0);
 
 	return 0;
 }

arch/arm/mach-mvebu/Kconfig

@@ -15,6 +15,7 @@ config ARCH_MVEBU
 	select MVEBU_CLK_GATING
 	select MVEBU_MBUS
 	select ZONE_DMA if ARM_LPAE
+	select ARCH_REQUIRE_GPIOLIB
 
 if ARCH_MVEBU
 

arch/arm/mach-mvebu/armada-370-xp.c

@@ -53,13 +53,6 @@ void __init armada_370_xp_init_early(void)
 {
 	char *mbus_soc_name;
 
-	/*
-	 * Some Armada 370/XP devices allocate their coherent buffers
-	 * from atomic context. Increase size of atomic coherent pool
-	 * to make sure such the allocations won't fail.
-	 */
-	init_dma_coherent_pool_size(SZ_1M);
-
 	/*
 	 * This initialization will be replaced by a DT-based
 	 * initialization once the mvebu-mbus driver gains DT support.

arch/arm/mach-omap1/dma.c

@@ -345,6 +345,7 @@ static int __init omap1_system_dma_init(void)
 		dev_err(&pdev->dev,
 			"%s: Memory allocation failed for d->chan!\n",
 			__func__);
+		ret = -ENOMEM;
 		goto exit_release_d;
 	}
 

arch/arm/mach-omap2/cclock33xx_data.c

@@ -454,9 +454,29 @@ DEFINE_CLK_GATE(cefuse_fck, "sys_clkin_ck", &sys_clkin_ck, 0x0,
  */
 DEFINE_CLK_FIXED_FACTOR(clkdiv32k_ck, "clk_24mhz", &clk_24mhz, 0x0, 1, 732);
 
-DEFINE_CLK_GATE(clkdiv32k_ick, "clkdiv32k_ck", &clkdiv32k_ck, 0x0,
-		AM33XX_CM_PER_CLKDIV32K_CLKCTRL, AM33XX_MODULEMODE_SWCTRL_SHIFT,
-		0x0, NULL);
+static struct clk clkdiv32k_ick;
+
+static const char *clkdiv32k_ick_parent_names[] = {
+	"clkdiv32k_ck",
+};
+
+static const struct clk_ops clkdiv32k_ick_ops = {
+	.enable         = &omap2_dflt_clk_enable,
+	.disable        = &omap2_dflt_clk_disable,
+	.is_enabled     = &omap2_dflt_clk_is_enabled,
+	.init           = &omap2_init_clk_clkdm,
+};
+
+static struct clk_hw_omap clkdiv32k_ick_hw = {
+	.hw	= {
+		.clk	= &clkdiv32k_ick,
+	},
+	.enable_reg	= AM33XX_CM_PER_CLKDIV32K_CLKCTRL,
+	.enable_bit	= AM33XX_MODULEMODE_SWCTRL_SHIFT,
+	.clkdm_name	= "clk_24mhz_clkdm",
+};
+
+DEFINE_STRUCT_CLK(clkdiv32k_ick, clkdiv32k_ick_parent_names, clkdiv32k_ick_ops);
 
 /* "usbotg_fck" is an additional clock and not really a modulemode */
 DEFINE_CLK_GATE(usbotg_fck, "dpll_per_ck", &dpll_per_ck, 0x0,

arch/arm/mach-omap2/omap_hwmod.c

@@ -1356,13 +1356,27 @@ static void _enable_sysc(struct omap_hwmod *oh)
 
 	clkdm = _get_clkdm(oh);
 	if (sf & SYSC_HAS_SIDLEMODE) {
+		if (oh->flags & HWMOD_SWSUP_SIDLE ||
+		    oh->flags & HWMOD_SWSUP_SIDLE_ACT) {
+			idlemode = HWMOD_IDLEMODE_NO;
+		} else {
+			if (sf & SYSC_HAS_ENAWAKEUP)
+				_enable_wakeup(oh, &v);
+			if (oh->class->sysc->idlemodes & SIDLE_SMART_WKUP)
+				idlemode = HWMOD_IDLEMODE_SMART_WKUP;
+			else
+				idlemode = HWMOD_IDLEMODE_SMART;
+		}
+
+		/*
+		 * This is special handling for some IPs like
+		 * 32k sync timer. Force them to idle!
+		 */
 		clkdm_act = (clkdm && clkdm->flags & CLKDM_ACTIVE_WITH_MPU);
 		if (clkdm_act && !(oh->class->sysc->idlemodes &
 				   (SIDLE_SMART | SIDLE_SMART_WKUP)))
 			idlemode = HWMOD_IDLEMODE_FORCE;
-		else
-			idlemode = (oh->flags & HWMOD_SWSUP_SIDLE) ?
-				HWMOD_IDLEMODE_NO : HWMOD_IDLEMODE_SMART;
+
 		_set_slave_idlemode(oh, idlemode, &v);
 	}
 
@@ -1391,10 +1405,6 @@ static void _enable_sysc(struct omap_hwmod *oh)
 	    (sf & SYSC_HAS_CLOCKACTIVITY))
 		_set_clockactivity(oh, oh->class->sysc->clockact, &v);
 
-	/* If slave is in SMARTIDLE, also enable wakeup */
-	if ((sf & SYSC_HAS_SIDLEMODE) && !(oh->flags & HWMOD_SWSUP_SIDLE))
-		_enable_wakeup(oh, &v);
-
 	_write_sysconfig(v, oh);
 
 	/*
@@ -1430,13 +1440,16 @@ static void _idle_sysc(struct omap_hwmod *oh)
 	sf = oh->class->sysc->sysc_flags;
 
 	if (sf & SYSC_HAS_SIDLEMODE) {
-		/* XXX What about HWMOD_IDLEMODE_SMART_WKUP? */
-		if (oh->flags & HWMOD_SWSUP_SIDLE ||
-		    !(oh->class->sysc->idlemodes &
-		      (SIDLE_SMART | SIDLE_SMART_WKUP)))
+		if (oh->flags & HWMOD_SWSUP_SIDLE) {
 			idlemode = HWMOD_IDLEMODE_FORCE;
+		} else {
+			if (sf & SYSC_HAS_ENAWAKEUP)
+				_enable_wakeup(oh, &v);
+			if (oh->class->sysc->idlemodes & SIDLE_SMART_WKUP)
+				idlemode = HWMOD_IDLEMODE_SMART_WKUP;
 			else
 				idlemode = HWMOD_IDLEMODE_SMART;
+		}
 		_set_slave_idlemode(oh, idlemode, &v);
 	}
 
@@ -1455,10 +1468,6 @@ static void _idle_sysc(struct omap_hwmod *oh)
 		_set_master_standbymode(oh, idlemode, &v);
 	}
 
-	/* If slave is in SMARTIDLE, also enable wakeup */
-	if ((sf & SYSC_HAS_SIDLEMODE) && !(oh->flags & HWMOD_SWSUP_SIDLE))
-		_enable_wakeup(oh, &v);
-
 	_write_sysconfig(v, oh);
 }
 
@@ -2065,7 +2074,7 @@ static int _omap4_get_context_lost(struct omap_hwmod *oh)
  * do so is present in the hwmod data, then call it and pass along the
  * return value; otherwise, return 0.
  */
-static int __init _enable_preprogram(struct omap_hwmod *oh)
+static int _enable_preprogram(struct omap_hwmod *oh)
 {
 	if (!oh->class->enable_preprogram)
 		return 0;
@@ -2245,42 +2254,6 @@ static int _idle(struct omap_hwmod *oh)
 	return 0;
 }
 
-/**
- * omap_hwmod_set_ocp_autoidle - set the hwmod's OCP autoidle bit
- * @oh: struct omap_hwmod *
- * @autoidle: desired AUTOIDLE bitfield value (0 or 1)
- *
- * Sets the IP block's OCP autoidle bit in hardware, and updates our
- * local copy. Intended to be used by drivers that require
- * direct manipulation of the AUTOIDLE bits.
- * Returns -EINVAL if @oh is null or is not in the ENABLED state, or passes
- * along the return value from _set_module_autoidle().
- *
- * Any users of this function should be scrutinized carefully.
- */
-int omap_hwmod_set_ocp_autoidle(struct omap_hwmod *oh, u8 autoidle)
-{
-	u32 v;
-	int retval = 0;
-	unsigned long flags;
-
-	if (!oh || oh->_state != _HWMOD_STATE_ENABLED)
-		return -EINVAL;
-
-	spin_lock_irqsave(&oh->_lock, flags);
-
-	v = oh->_sysc_cache;
-
-	retval = _set_module_autoidle(oh, autoidle, &v);
-
-	if (!retval)
-		_write_sysconfig(v, oh);
-
-	spin_unlock_irqrestore(&oh->_lock, flags);
-
-	return retval;
-}
-
 /**
  * _shutdown - shutdown an omap_hwmod
  * @oh: struct omap_hwmod *
@@ -3179,38 +3152,6 @@ int omap_hwmod_softreset(struct omap_hwmod *oh)
 	return ret;
 }
 
-/**
- * omap_hwmod_set_slave_idlemode - set the hwmod's OCP slave idlemode
- * @oh: struct omap_hwmod *
- * @idlemode: SIDLEMODE field bits (shifted to bit 0)
- *
- * Sets the IP block's OCP slave idlemode in hardware, and updates our
- * local copy.  Intended to be used by drivers that have some erratum
- * that requires direct manipulation of the SIDLEMODE bits.  Returns
- * -EINVAL if @oh is null, or passes along the return value from
- * _set_slave_idlemode().
- *
- * XXX Does this function have any current users?  If not, we should
- * remove it; it is better to let the rest of the hwmod code handle this.
- * Any users of this function should be scrutinized carefully.
- */
-int omap_hwmod_set_slave_idlemode(struct omap_hwmod *oh, u8 idlemode)
-{
-	u32 v;
-	int retval = 0;
-
-	if (!oh)
-		return -EINVAL;
-
-	v = oh->_sysc_cache;
-
-	retval = _set_slave_idlemode(oh, idlemode, &v);
-	if (!retval)
-		_write_sysconfig(v, oh);
-
-	return retval;
-}
-
 /**
  * omap_hwmod_lookup - look up a registered omap_hwmod by name
  * @name: name of the omap_hwmod to look up

arch/arm/mach-omap2/omap_hwmod.h

@@ -463,6 +463,9 @@ struct omap_hwmod_omap4_prcm {
  *     is kept in force-standby mode. Failing to do so causes PM problems
  *     with musb on OMAP3630 at least. Note that musb has a dedicated register
  *     to control MSTANDBY signal when MIDLEMODE is set to force-standby.
+ * HWMOD_SWSUP_SIDLE_ACT: omap_hwmod code should manually bring the module
+ *     out of idle, but rely on smart-idle to the put it back in idle,
+ *     so the wakeups are still functional (Only known case for now is UART)
  */
 #define HWMOD_SWSUP_SIDLE			(1 << 0)
 #define HWMOD_SWSUP_MSTANDBY			(1 << 1)
@@ -476,6 +479,7 @@ struct omap_hwmod_omap4_prcm {
 #define HWMOD_EXT_OPT_MAIN_CLK			(1 << 9)
 #define HWMOD_BLOCK_WFI				(1 << 10)
 #define HWMOD_FORCE_MSTANDBY			(1 << 11)
+#define HWMOD_SWSUP_SIDLE_ACT			(1 << 12)
 
 /*
  * omap_hwmod._int_flags definitions
@@ -641,9 +645,6 @@ int omap_hwmod_read_hardreset(struct omap_hwmod *oh, const char *name);
 int omap_hwmod_enable_clocks(struct omap_hwmod *oh);
 int omap_hwmod_disable_clocks(struct omap_hwmod *oh);
 
-int omap_hwmod_set_slave_idlemode(struct omap_hwmod *oh, u8 idlemode);
-int omap_hwmod_set_ocp_autoidle(struct omap_hwmod *oh, u8 autoidle);
-
 int omap_hwmod_reset(struct omap_hwmod *oh);
 void omap_hwmod_ocp_barrier(struct omap_hwmod *oh);
 

arch/arm/mach-omap2/omap_hwmod_2xxx_ipblock_data.c

@@ -512,6 +512,7 @@ struct omap_hwmod omap2xxx_uart1_hwmod = {
 	.mpu_irqs	= omap2_uart1_mpu_irqs,
 	.sdma_reqs	= omap2_uart1_sdma_reqs,
 	.main_clk	= "uart1_fck",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.prcm		= {
 		.omap2 = {
 			.module_offs = CORE_MOD,
@@ -531,6 +532,7 @@ struct omap_hwmod omap2xxx_uart2_hwmod = {
 	.mpu_irqs	= omap2_uart2_mpu_irqs,
 	.sdma_reqs	= omap2_uart2_sdma_reqs,
 	.main_clk	= "uart2_fck",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.prcm		= {
 		.omap2 = {
 			.module_offs = CORE_MOD,
@@ -550,6 +552,7 @@ struct omap_hwmod omap2xxx_uart3_hwmod = {
 	.mpu_irqs	= omap2_uart3_mpu_irqs,
 	.sdma_reqs	= omap2_uart3_sdma_reqs,
 	.main_clk	= "uart3_fck",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.prcm		= {
 		.omap2 = {
 			.module_offs = CORE_MOD,

arch/arm/mach-omap2/omap_hwmod_33xx_data.c

@@ -1995,6 +1995,7 @@ static struct omap_hwmod am33xx_uart1_hwmod = {
 	.name		= "uart1",
 	.class		= &uart_class,
 	.clkdm_name	= "l4_wkup_clkdm",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.mpu_irqs	= am33xx_uart1_irqs,
 	.sdma_reqs	= uart1_edma_reqs,
 	.main_clk	= "dpll_per_m2_div4_wkupdm_ck",
@@ -2015,6 +2016,7 @@ static struct omap_hwmod am33xx_uart2_hwmod = {
 	.name		= "uart2",
 	.class		= &uart_class,
 	.clkdm_name	= "l4ls_clkdm",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.mpu_irqs	= am33xx_uart2_irqs,
 	.sdma_reqs	= uart1_edma_reqs,
 	.main_clk	= "dpll_per_m2_div4_ck",
@@ -2042,6 +2044,7 @@ static struct omap_hwmod am33xx_uart3_hwmod = {
 	.name		= "uart3",
 	.class		= &uart_class,
 	.clkdm_name	= "l4ls_clkdm",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.mpu_irqs	= am33xx_uart3_irqs,
 	.sdma_reqs	= uart3_edma_reqs,
 	.main_clk	= "dpll_per_m2_div4_ck",
@@ -2062,6 +2065,7 @@ static struct omap_hwmod am33xx_uart4_hwmod = {
 	.name		= "uart4",
 	.class		= &uart_class,
 	.clkdm_name	= "l4ls_clkdm",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.mpu_irqs	= am33xx_uart4_irqs,
 	.sdma_reqs	= uart1_edma_reqs,
 	.main_clk	= "dpll_per_m2_div4_ck",
@@ -2082,6 +2086,7 @@ static struct omap_hwmod am33xx_uart5_hwmod = {
 	.name		= "uart5",
 	.class		= &uart_class,
 	.clkdm_name	= "l4ls_clkdm",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.mpu_irqs	= am33xx_uart5_irqs,
 	.sdma_reqs	= uart1_edma_reqs,
 	.main_clk	= "dpll_per_m2_div4_ck",
@@ -2102,6 +2107,7 @@ static struct omap_hwmod am33xx_uart6_hwmod = {
 	.name		= "uart6",
 	.class		= &uart_class,
 	.clkdm_name	= "l4ls_clkdm",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.mpu_irqs	= am33xx_uart6_irqs,
 	.sdma_reqs	= uart1_edma_reqs,
 	.main_clk	= "dpll_per_m2_div4_ck",

arch/arm/mach-omap2/omap_hwmod_3xxx_data.c

@@ -490,6 +490,7 @@ static struct omap_hwmod omap3xxx_uart1_hwmod = {
 	.mpu_irqs	= omap2_uart1_mpu_irqs,
 	.sdma_reqs	= omap2_uart1_sdma_reqs,
 	.main_clk	= "uart1_fck",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.prcm		= {
 		.omap2 = {
 			.module_offs = CORE_MOD,
@@ -508,6 +509,7 @@ static struct omap_hwmod omap3xxx_uart2_hwmod = {
 	.mpu_irqs	= omap2_uart2_mpu_irqs,
 	.sdma_reqs	= omap2_uart2_sdma_reqs,
 	.main_clk	= "uart2_fck",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.prcm		= {
 		.omap2 = {
 			.module_offs = CORE_MOD,
@@ -526,6 +528,7 @@ static struct omap_hwmod omap3xxx_uart3_hwmod = {
 	.mpu_irqs	= omap2_uart3_mpu_irqs,
 	.sdma_reqs	= omap2_uart3_sdma_reqs,
 	.main_clk	= "uart3_fck",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.prcm		= {
 		.omap2 = {
 			.module_offs = OMAP3430_PER_MOD,
@@ -555,6 +558,7 @@ static struct omap_hwmod omap36xx_uart4_hwmod = {
 	.mpu_irqs	= uart4_mpu_irqs,
 	.sdma_reqs	= uart4_sdma_reqs,
 	.main_clk	= "uart4_fck",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.prcm		= {
 		.omap2 = {
 			.module_offs = OMAP3430_PER_MOD,

arch/arm/mach-omap2/omap_hwmod_44xx_data.c

@@ -3434,6 +3434,7 @@ static struct omap_hwmod omap44xx_uart1_hwmod = {
 	.name		= "uart1",
 	.class		= &omap44xx_uart_hwmod_class,
 	.clkdm_name	= "l4_per_clkdm",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.mpu_irqs	= omap44xx_uart1_irqs,
 	.sdma_reqs	= omap44xx_uart1_sdma_reqs,
 	.main_clk	= "func_48m_fclk",
@@ -3462,6 +3463,7 @@ static struct omap_hwmod omap44xx_uart2_hwmod = {
 	.name		= "uart2",
 	.class		= &omap44xx_uart_hwmod_class,
 	.clkdm_name	= "l4_per_clkdm",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.mpu_irqs	= omap44xx_uart2_irqs,
 	.sdma_reqs	= omap44xx_uart2_sdma_reqs,
 	.main_clk	= "func_48m_fclk",
@@ -3490,7 +3492,8 @@ static struct omap_hwmod omap44xx_uart3_hwmod = {
 	.name		= "uart3",
 	.class		= &omap44xx_uart_hwmod_class,
 	.clkdm_name	= "l4_per_clkdm",
-	.flags		= HWMOD_INIT_NO_IDLE | HWMOD_INIT_NO_RESET,
+	.flags		= HWMOD_INIT_NO_IDLE | HWMOD_INIT_NO_RESET |
+				HWMOD_SWSUP_SIDLE_ACT,
 	.mpu_irqs	= omap44xx_uart3_irqs,
 	.sdma_reqs	= omap44xx_uart3_sdma_reqs,
 	.main_clk	= "func_48m_fclk",
@@ -3519,6 +3522,7 @@ static struct omap_hwmod omap44xx_uart4_hwmod = {
 	.name		= "uart4",
 	.class		= &omap44xx_uart_hwmod_class,
 	.clkdm_name	= "l4_per_clkdm",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.mpu_irqs	= omap44xx_uart4_irqs,
 	.sdma_reqs	= omap44xx_uart4_sdma_reqs,
 	.main_clk	= "func_48m_fclk",

arch/arm/mach-omap2/serial.c

@@ -95,38 +95,9 @@ static void omap_uart_enable_wakeup(struct device *dev, bool enable)
 		omap_hwmod_disable_wakeup(od->hwmods[0]);
 }
 
-/*
- * Errata i291: [UART]:Cannot Acknowledge Idle Requests
- * in Smartidle Mode When Configured for DMA Operations.
- * WA: configure uart in force idle mode.
- */
-static void omap_uart_set_noidle(struct device *dev)
-{
-	struct platform_device *pdev = to_platform_device(dev);
-	struct omap_device *od = to_omap_device(pdev);
-
-	omap_hwmod_set_slave_idlemode(od->hwmods[0], HWMOD_IDLEMODE_NO);
-}
-
-static void omap_uart_set_smartidle(struct device *dev)
-{
-	struct platform_device *pdev = to_platform_device(dev);
-	struct omap_device *od = to_omap_device(pdev);
-	u8 idlemode;
-
-	if (od->hwmods[0]->class->sysc->idlemodes & SIDLE_SMART_WKUP)
-		idlemode = HWMOD_IDLEMODE_SMART_WKUP;
-	else
-		idlemode = HWMOD_IDLEMODE_SMART;
-
-	omap_hwmod_set_slave_idlemode(od->hwmods[0], idlemode);
-}
-
 #else
 static void omap_uart_enable_wakeup(struct device *dev, bool enable)
 {}
-static void omap_uart_set_noidle(struct device *dev) {}
-static void omap_uart_set_smartidle(struct device *dev) {}
 #endif /* CONFIG_PM */
 
 #ifdef CONFIG_OMAP_MUX
@@ -299,8 +270,6 @@ void __init omap_serial_init_port(struct omap_board_data *bdata,
 	omap_up.uartclk = OMAP24XX_BASE_BAUD * 16;
 	omap_up.flags = UPF_BOOT_AUTOCONF;
 	omap_up.get_context_loss_count = omap_pm_get_dev_context_loss_count;
-	omap_up.set_forceidle = omap_uart_set_smartidle;
-	omap_up.set_noidle = omap_uart_set_noidle;
 	omap_up.enable_wakeup = omap_uart_enable_wakeup;
 	omap_up.dma_rx_buf_size = info->dma_rx_buf_size;
 	omap_up.dma_rx_timeout = info->dma_rx_timeout;

arch/arm/mach-orion5x/common.c

@@ -199,13 +199,6 @@ void __init orion5x_init_early(void)
 
 	orion_time_set_base(TIMER_VIRT_BASE);
 
-	/*
-	 * Some Orion5x devices allocate their coherent buffers from atomic
-	 * context. Increase size of atomic coherent pool to make sure such
-	 * the allocations won't fail.
-	 */
-	init_dma_coherent_pool_size(SZ_1M);
-
 	/* Initialize the MBUS driver */
 	orion5x_pcie_id(&dev, &rev);
 	if (dev == MV88F5281_DEV_ID)

arch/arm/mach-shmobile/board-marzen.c

@@ -212,8 +212,8 @@ static struct platform_device *marzen_devices[] __initdata = {
 static struct usb_phy *phy;
 static int usb_power_on(struct platform_device *pdev)
 {
-	if (!phy)
-		return -EIO;
+	if (IS_ERR(phy))
+		return PTR_ERR(phy);
 
 	pm_runtime_enable(&pdev->dev);
 	pm_runtime_get_sync(&pdev->dev);
@@ -225,7 +225,7 @@ static int usb_power_on(struct platform_device *pdev)
 
 static void usb_power_off(struct platform_device *pdev)
 {
-	if (!phy)
+	if (IS_ERR(phy))
 		return;
 
 	usb_phy_shutdown(phy);

arch/arm/mach-sunxi/Kconfig

 config ARCH_SUNXI
 	bool "Allwinner A1X SOCs" if ARCH_MULTI_V7
+	select ARCH_REQUIRE_GPIOLIB
 	select CLKSRC_MMIO
 	select CLKSRC_OF
 	select COMMON_CLK

arch/arm/mach-ux500/Kconfig

@@ -51,6 +51,7 @@ config MACH_MOP500
 	bool "U8500 Development platform, MOP500 versions"
 	select I2C
 	select I2C_NOMADIK
+	select REGULATOR
 	select REGULATOR_FIXED_VOLTAGE
 	select SOC_BUS
 	select UX500_SOC_DB8500

arch/arm/mach-ux500/board-mop500.c

@@ -623,7 +623,7 @@ static void __init mop500_init_machine(void)
 	sdi0_reg_info.gpios[0].gpio = GPIO_SDMMC_1V8_3V_SEL;
 
 	mop500_pinmaps_init();
-	parent = u8500_init_devices(&ab8500_platdata);
+	parent = u8500_init_devices();
 
 	for (i = 0; i < ARRAY_SIZE(mop500_platform_devs); i++)
 		mop500_platform_devs[i]->dev.parent = parent;
@@ -660,7 +660,7 @@ static void __init snowball_init_machine(void)
 	sdi0_reg_info.gpios[0].gpio = SNOWBALL_SDMMC_1V8_3V_GPIO;
 
 	snowball_pinmaps_init();
-	parent = u8500_init_devices(&ab8500_platdata);
+	parent = u8500_init_devices();
 
 	for (i = 0; i < ARRAY_SIZE(snowball_platform_devs); i++)
 		snowball_platform_devs[i]->dev.parent = parent;
@@ -698,7 +698,7 @@ static void __init hrefv60_init_machine(void)
 	sdi0_reg_info.gpios[0].gpio = HREFV60_SDMMC_1V8_3V_GPIO;
 
 	hrefv60_pinmaps_init();
-	parent = u8500_init_devices(&ab8500_platdata);
+	parent = u8500_init_devices();
 
 	for (i = 0; i < ARRAY_SIZE(mop500_platform_devs); i++)
 		mop500_platform_devs[i]->dev.parent = parent;

arch/arm/mach-ux500/cpu-db8500.c

@@ -206,7 +206,7 @@ static struct device * __init db8500_soc_device_init(void)
 /*
  * This function is called from the board init
  */
-struct device * __init u8500_init_devices(struct ab8500_platform_data *ab8500)
+struct device * __init u8500_init_devices(void)
 {
 	struct device *parent;
 	int i;
@@ -220,8 +220,6 @@ struct device * __init u8500_init_devices(struct ab8500_platform_data *ab8500)
 	for (i = 0; i < ARRAY_SIZE(platform_devs); i++)
 		platform_devs[i]->dev.parent = parent;
 
-	db8500_prcmu_device.dev.platform_data = ab8500;
-
 	platform_add_devices(platform_devs, ARRAY_SIZE(platform_devs));
 
 	return parent;
@@ -278,7 +276,7 @@ static struct of_dev_auxdata u8500_auxdata_lookup[] __initdata = {
 	OF_DEV_AUXDATA("st,nomadik-i2c", 0x8012a000, "nmk-i2c.4", NULL),
 	OF_DEV_AUXDATA("stericsson,db8500-prcmu", 0x80157000, "db8500-prcmu",
 			&db8500_prcmu_pdata),
-	OF_DEV_AUXDATA("smsc,lan9115", 0x50000000, "smsc911x", NULL),
+	OF_DEV_AUXDATA("smsc,lan9115", 0x50000000, "smsc911x.0", NULL),
 	/* Requires device name bindings. */
 	OF_DEV_AUXDATA("stericsson,nmk-pinctrl", U8500_PRCMU_BASE,
 		"pinctrl-db8500", NULL),

arch/arm/mach-ux500/setup.h

@@ -18,7 +18,7 @@
 void __init ux500_map_io(void);
 extern void __init u8500_map_io(void);
 
-extern struct device * __init u8500_init_devices(struct ab8500_platform_data *ab8500);
+extern struct device * __init u8500_init_devices(void);
 
 extern void __init ux500_init_irq(void);
 extern void __init ux500_init_late(void);

arch/arm/mach-vt8500/vt8500.c

@@ -173,6 +173,7 @@ static const char * const vt8500_dt_compat[] = {
 	"wm,wm8505",
 	"wm,wm8750",
 	"wm,wm8850",
+	NULL
 };
 
 DT_MACHINE_START(WMT_DT, "VIA/Wondermedia SoC (Device Tree Support)")

arch/arm/plat-orion/common.c

@@ -383,7 +383,7 @@ static struct resource orion_ge10_shared_resources[] = {
 
 static struct platform_device orion_ge10_shared = {
 	.name		= MV643XX_ETH_SHARED_NAME,
-	.id		= 1,
+	.id		= 2,
 	.dev		= {
 		.platform_data	= &orion_ge10_shared_data,
 	},
@@ -398,8 +398,8 @@ static struct resource orion_ge10_resources[] = {
 
 static struct platform_device orion_ge10 = {
 	.name		= MV643XX_ETH_NAME,
-	.id		= 1,
-	.num_resources	= 2,
+	.id		= 2,
+	.num_resources	= 1,
 	.resource	= orion_ge10_resources,
 	.dev		= {
 		.coherent_dma_mask	= DMA_BIT_MASK(32),
@@ -432,7 +432,7 @@ static struct resource orion_ge11_shared_resources[] = {
 
 static struct platform_device orion_ge11_shared = {
 	.name		= MV643XX_ETH_SHARED_NAME,
-	.id		= 1,
+	.id		= 3,
 	.dev		= {
 		.platform_data	= &orion_ge11_shared_data,
 	},
@@ -447,8 +447,8 @@ static struct resource orion_ge11_resources[] = {
 
 static struct platform_device orion_ge11 = {
 	.name		= MV643XX_ETH_NAME,
-	.id		= 1,
-	.num_resources	= 2,
+	.id		= 3,
+	.num_resources	= 1,
 	.resource	= orion_ge11_resources,
 	.dev		= {
 		.coherent_dma_mask	= DMA_BIT_MASK(32),

arch/arm/plat-orion/include/plat/common.h

@@ -10,6 +10,7 @@
 
 #ifndef __PLAT_COMMON_H
 #include <linux/mv643xx_eth.h>
+#include <linux/platform_data/usb-ehci-orion.h>
 
 struct dsa_platform_data;
 struct mv_sata_platform_data;

drivers/clk/tegra/clk-tegra20.c

@@ -872,6 +872,14 @@ static void __init tegra20_periph_clk_init(void)
 	struct clk *clk;
 	int i;
 
+	/* ac97 */
+	clk = tegra_clk_register_periph_gate("ac97", "pll_a_out0",
+				    TEGRA_PERIPH_ON_APB,
+				    clk_base, 0, 3, &periph_l_regs,
+				    periph_clk_enb_refcnt);
+	clk_register_clkdev(clk, NULL, "tegra20-ac97");
+	clks[ac97] = clk;
+
 	/* apbdma */
 	clk = tegra_clk_register_periph_gate("apbdma", "pclk", 0, clk_base,
 				    0, 34, &periph_h_regs,
@@ -1234,9 +1242,6 @@ static __initdata struct tegra_clk_init_table init_table[] = {
 	{uartc, pll_p, 0, 0},
 	{uartd, pll_p, 0, 0},
 	{uarte, pll_p, 0, 0},
-	{usbd, clk_max, 12000000, 0},
-	{usb2, clk_max, 12000000, 0},
-	{usb3, clk_max, 12000000, 0},
 	{pll_a, clk_max, 56448000, 1},
 	{pll_a_out0, clk_max, 11289600, 1},
 	{cdev1, clk_max, 0, 1},

drivers/tty/serial/omap-serial.c

@@ -202,26 +202,6 @@ static int serial_omap_get_context_loss_count(struct uart_omap_port *up)
 	return pdata->get_context_loss_count(up->dev);
 }
 
-static void serial_omap_set_forceidle(struct uart_omap_port *up)
-{
-	struct omap_uart_port_info *pdata = up->dev->platform_data;
-
-	if (!pdata || !pdata->set_forceidle)
-		return;
-
-	pdata->set_forceidle(up->dev);
-}
-
-static void serial_omap_set_noidle(struct uart_omap_port *up)
-{
-	struct omap_uart_port_info *pdata = up->dev->platform_data;
-
-	if (!pdata || !pdata->set_noidle)
-		return;
-
-	pdata->set_noidle(up->dev);
-}
-
 static void serial_omap_enable_wakeup(struct uart_omap_port *up, bool enable)
 {
 	struct omap_uart_port_info *pdata = up->dev->platform_data;
@@ -298,8 +278,6 @@ static void serial_omap_stop_tx(struct uart_port *port)
 		serial_out(up, UART_IER, up->ier);
 	}
 
-	serial_omap_set_forceidle(up);
-
 	pm_runtime_mark_last_busy(up->dev);
 	pm_runtime_put_autosuspend(up->dev);
 }
@@ -364,7 +342,6 @@ static void serial_omap_start_tx(struct uart_port *port)
 
 	pm_runtime_get_sync(up->dev);
 	serial_omap_enable_ier_thri(up);
-	serial_omap_set_noidle(up);
 	pm_runtime_mark_last_busy(up->dev);
 	pm_runtime_put_autosuspend(up->dev);
 }

include/linux/platform_data/serial-omap.h

@@ -43,8 +43,6 @@ struct omap_uart_port_info {
 	int			DTR_present;
 
 	int (*get_context_loss_count)(struct device *);
-	void (*set_forceidle)(struct device *);
-	void (*set_noidle)(struct device *);
 	void (*enable_wakeup)(struct device *, bool);
 };