Merge git://git.kernel.org/pub/scm/linux/kernel/git/nico/orion into devel-stable

arch/arm/mach-dove/mpp.c

@@ -11,24 +11,17 @@
 #include <linux/kernel.h>
 #include <linux/gpio.h>
 #include <linux/io.h>
-
+#include <plat/mpp.h>
 #include <mach/dove.h>
-
 #include "mpp.h"
 
-#define MPP_NR_REGS 4
-#define MPP_CTRL(i)	((i) == 3 ?				\
-			 DOVE_MPP_CTRL4_VIRT_BASE :		\
-			 DOVE_MPP_VIRT_BASE + (i) * 4)
-#define PMU_SIG_REGS 2
-#define PMU_SIG_CTRL(i)	(DOVE_PMU_SIG_CTRL + (i) * 4)
-
 struct dove_mpp_grp {
 	int start;
 	int end;
 };
 
-static struct dove_mpp_grp dove_mpp_grp[] = {
+/* Map a group to a range of GPIO pins in that group */
+static const struct dove_mpp_grp dove_mpp_grp[] = {
 	[MPP_24_39] = {
 		.start	= 24,
 		.end	= 39,
@@ -38,8 +31,8 @@ static struct dove_mpp_grp dove_mpp_grp[] = {
 		.end	= 45,
 	},
 	[MPP_46_51] = {
-		.start	= 40,
-		.end	= 45,
+		.start	= 46,
+		.end	= 51,
 	},
 	[MPP_58_61] = {
 		.start	= 58,
@@ -51,6 +44,8 @@ static struct dove_mpp_grp dove_mpp_grp[] = {
 	},
 };
 
+/* Enable gpio for a range of pins. mode should be a combination of
+   GPIO_OUTPUT_OK | GPIO_INPUT_OK */
 static void dove_mpp_gpio_mode(int start, int end, int gpio_mode)
 {
 	int i;
@@ -59,24 +54,17 @@ static void dove_mpp_gpio_mode(int start, int end, int gpio_mode)
 		orion_gpio_set_valid(i, gpio_mode);
 }
 
+/* Dump all the extra MPP registers. The platform code will dump the
+   registers for pins 0-23. */
 static void dove_mpp_dump_regs(void)
 {
-#ifdef DEBUG
-	int i;
-
-	pr_debug("MPP_CTRL regs:");
-	for (i = 0; i < MPP_NR_REGS; i++)
-		printk(" %08x", readl(MPP_CTRL(i)));
-	printk("\n");
+	pr_debug("PMU_CTRL4_CTRL: %08x\n",
+		 readl(DOVE_MPP_CTRL4_VIRT_BASE));
 
-	pr_debug("PMU_SIG_CTRL regs:");
-	for (i = 0; i < PMU_SIG_REGS; i++)
-		printk(" %08x", readl(PMU_SIG_CTRL(i)));
-	printk("\n");
+	pr_debug("PMU_MPP_GENERAL_CTRL: %08x\n",
+		 readl(DOVE_PMU_MPP_GENERAL_CTRL));
 
-	pr_debug("PMU_MPP_GENERAL_CTRL: %08x\n", readl(DOVE_PMU_MPP_GENERAL_CTRL));
 	pr_debug("MPP_GENERAL: %08x\n", readl(DOVE_MPP_GENERAL_VIRT_BASE));
-#endif
 }
 
 static void dove_mpp_cfg_nfc(int sel)
@@ -128,82 +116,46 @@ static void dove_mpp_cfg_au1(int sel)
 	writel(global_cfg_2, DOVE_GLOBAL_CONFIG_2);
 }
 
-static void dove_mpp_conf_grp(int num, int sel, u32 *mpp_ctrl)
+/* Configure the group registers, enabling GPIO if sel indicates the
+   pin is to be used for GPIO */
+static void dove_mpp_conf_grp(unsigned int *mpp_grp_list)
 {
-	int start = dove_mpp_grp[num].start;
-	int end = dove_mpp_grp[num].end;
-	int gpio_mode = sel ? GPIO_OUTPUT_OK | GPIO_INPUT_OK : 0;
-
-	*mpp_ctrl &= ~(0x1 << num);
-	*mpp_ctrl |= sel << num;
-
-	dove_mpp_gpio_mode(start, end, gpio_mode);
-}
-
-void __init dove_mpp_conf(unsigned int *mpp_list)
-{
-	u32 mpp_ctrl[MPP_NR_REGS];
-	u32 pmu_mpp_ctrl = 0;
-	u32 pmu_sig_ctrl[PMU_SIG_REGS];
-	int i;
-
-	for (i = 0; i < MPP_NR_REGS; i++)
-		mpp_ctrl[i] = readl(MPP_CTRL(i));
-
-	for (i = 0; i < PMU_SIG_REGS; i++)
-		pmu_sig_ctrl[i] = readl(PMU_SIG_CTRL(i));
-
-	pmu_mpp_ctrl = readl(DOVE_PMU_MPP_GENERAL_CTRL);
-
-	dove_mpp_dump_regs();
-
-	for ( ; *mpp_list != MPP_END; mpp_list++) {
-		unsigned int num = MPP_NUM(*mpp_list);
-		unsigned int sel = MPP_SEL(*mpp_list);
-		int shift, gpio_mode;
-
-		if (num > MPP_MAX) {
-			pr_err("dove: invalid MPP number (%u)\n", num);
-			continue;
-		}
-
-		if (*mpp_list & MPP_NFC_MASK) {
-			dove_mpp_cfg_nfc(sel);
-			continue;
-		}
+	u32 mpp_ctrl4 = readl(DOVE_MPP_CTRL4_VIRT_BASE);
+	int gpio_mode;
 
-		if (*mpp_list & MPP_AU1_MASK) {
-			dove_mpp_cfg_au1(sel);
-			continue;
-		}
+	for ( ; *mpp_grp_list; mpp_grp_list++) {
+		unsigned int num = MPP_NUM(*mpp_grp_list);
+		unsigned int sel = MPP_SEL(*mpp_grp_list);
 
-		if (*mpp_list & MPP_GRP_MASK) {
-			dove_mpp_conf_grp(num, sel, &mpp_ctrl[3]);
+		if (num > MPP_GRP_MAX) {
+			pr_err("dove: invalid MPP GRP number (%u)\n", num);
 			continue;
 		}
 
-		shift = (num & 7) << 2;
-		if (*mpp_list & MPP_PMU_MASK) {
-			pmu_mpp_ctrl |= (0x1 << num);
-			pmu_sig_ctrl[num / 8] &= ~(0xf << shift);
-			pmu_sig_ctrl[num / 8] |= 0xf << shift;
-			gpio_mode = 0;
-		} else {
-			mpp_ctrl[num / 8] &= ~(0xf << shift);
-			mpp_ctrl[num / 8] |= sel << shift;
-			gpio_mode = GPIO_OUTPUT_OK | GPIO_INPUT_OK;
-		}
+		mpp_ctrl4 &= ~(0x1 << num);
+		mpp_ctrl4 |= sel << num;
 
-		orion_gpio_set_valid(num, gpio_mode);
+		gpio_mode = sel ? GPIO_OUTPUT_OK | GPIO_INPUT_OK : 0;
+		dove_mpp_gpio_mode(dove_mpp_grp[num].start,
+				   dove_mpp_grp[num].end, gpio_mode);
 	}
+	writel(mpp_ctrl4, DOVE_MPP_CTRL4_VIRT_BASE);
+}
 
-	for (i = 0; i < MPP_NR_REGS; i++)
-		writel(mpp_ctrl[i], MPP_CTRL(i));
+/* Configure the various MPP pins on Dove */
+void __init dove_mpp_conf(unsigned int *mpp_list,
+			  unsigned int *mpp_grp_list,
+			  unsigned int grp_au1_52_57,
+			  unsigned int grp_nfc_64_71)
+{
+	dove_mpp_dump_regs();
 
-	for (i = 0; i < PMU_SIG_REGS; i++)
-		writel(pmu_sig_ctrl[i], PMU_SIG_CTRL(i));
+	/* Use platform code for pins 0-23 */
+	orion_mpp_conf(mpp_list, 0, MPP_MAX, DOVE_MPP_VIRT_BASE);
 
-	writel(pmu_mpp_ctrl, DOVE_PMU_MPP_GENERAL_CTRL);
+	dove_mpp_conf_grp(mpp_grp_list);
+	dove_mpp_cfg_au1(grp_au1_52_57);
+	dove_mpp_cfg_nfc(grp_nfc_64_71);
 
 	dove_mpp_dump_regs();
 }

arch/arm/mach-kirkwood/include/mach/irqs.h

@@ -51,6 +51,7 @@
 #define IRQ_KIRKWOOD_GPIO_HIGH_16_23	41
 #define IRQ_KIRKWOOD_GE00_ERR	46
 #define IRQ_KIRKWOOD_GE01_ERR	47
+#define IRQ_KIRKWOOD_RTC        53
 
 /*
  * KIRKWOOD General Purpose Pins

arch/arm/mach-kirkwood/mpp.c

@@ -14,6 +14,7 @@
 #include <linux/io.h>
 #include <asm/gpio.h>
 #include <mach/hardware.h>
+#include <plat/mpp.h>
 #include "common.h"
 #include "mpp.h"
 
@@ -36,61 +37,8 @@ static unsigned int __init kirkwood_variant(void)
 	return 0;
 }
 
-#define MPP_CTRL(i)	(DEV_BUS_VIRT_BASE + (i) * 4)
-#define MPP_NR_REGS	(1 + MPP_MAX/8)
-
 void __init kirkwood_mpp_conf(unsigned int *mpp_list)
 {
-	u32 mpp_ctrl[MPP_NR_REGS];
-	unsigned int variant_mask;
-	int i;
-
-	variant_mask = kirkwood_variant();
-	if (!variant_mask)
-		return;
-
-	printk(KERN_DEBUG "initial MPP regs:");
-	for (i = 0; i < MPP_NR_REGS; i++) {
-		mpp_ctrl[i] = readl(MPP_CTRL(i));
-		printk(" %08x", mpp_ctrl[i]);
-	}
-	printk("\n");
-
-	for ( ; *mpp_list; mpp_list++) {
-		unsigned int num = MPP_NUM(*mpp_list);
-		unsigned int sel = MPP_SEL(*mpp_list);
-		int shift, gpio_mode;
-
-		if (num > MPP_MAX) {
-			printk(KERN_ERR "kirkwood_mpp_conf: invalid MPP "
-					"number (%u)\n", num);
-			continue;
-		}
-		if (!(*mpp_list & variant_mask)) {
-			printk(KERN_WARNING
-			       "kirkwood_mpp_conf: requested MPP%u config "
-			       "unavailable on this hardware\n", num);
-			continue;
-		}
-
-		shift = (num & 7) << 2;
-		mpp_ctrl[num / 8] &= ~(0xf << shift);
-		mpp_ctrl[num / 8] |= sel << shift;
-
-		gpio_mode = 0;
-		if (*mpp_list & MPP_INPUT_MASK)
-			gpio_mode |= GPIO_INPUT_OK;
-		if (*mpp_list & MPP_OUTPUT_MASK)
-			gpio_mode |= GPIO_OUTPUT_OK;
-		if (sel != 0)
-			gpio_mode = 0;
-		orion_gpio_set_valid(num, gpio_mode);
-	}
-
-	printk(KERN_DEBUG "  final MPP regs:");
-	for (i = 0; i < MPP_NR_REGS; i++) {
-		writel(mpp_ctrl[i], MPP_CTRL(i));
-		printk(" %08x", mpp_ctrl[i]);
-	}
-	printk("\n");
+	orion_mpp_conf(mpp_list, kirkwood_variant(),
+		       MPP_MAX, DEV_BUS_VIRT_BASE);
 }

arch/arm/mach-kirkwood/mpp.h

@@ -22,14 +22,8 @@
 	/* available on F6281 */	((!!(_F6281)) << 17) | \
 	/* available on F6282 */	((!!(_F6282)) << 18))
 
-#define MPP_NUM(x)	((x) & 0xff)
-#define MPP_SEL(x)	(((x) >> 8) & 0xf)
-
 				/*   num sel  i  o  6180 6190 6192 6281 6282 */
 
-#define MPP_INPUT_MASK		MPP(  0, 0x0, 1, 0, 0,   0,   0,   0,   0 )
-#define MPP_OUTPUT_MASK		MPP(  0, 0x0, 0, 1, 0,   0,   0,   0,   0 )
-
 #define MPP_F6180_MASK		MPP(  0, 0x0, 0, 0, 1,   0,   0,   0,   0 )
 #define MPP_F6190_MASK		MPP(  0, 0x0, 0, 0, 0,   1,   0,   0,   0 )
 #define MPP_F6192_MASK		MPP(  0, 0x0, 0, 0, 0,   0,   1,   0,   0 )

arch/arm/mach-loki/common.c

@@ -13,7 +13,7 @@
 #include <linux/platform_device.h>
 #include <linux/serial_8250.h>
 #include <linux/mbus.h>
-#include <linux/mv643xx_eth.h>
+#include <linux/dma-mapping.h>
 #include <asm/page.h>
 #include <asm/timex.h>
 #include <asm/mach/map.h>
@@ -22,6 +22,7 @@
 #include <mach/loki.h>
 #include <plat/orion_nand.h>
 #include <plat/time.h>
+#include <plat/common.h>
 #include "common.h"
 
 /*****************************************************************************
@@ -43,116 +44,28 @@ void __init loki_map_io(void)
 
 
 /*****************************************************************************
- * GE0
+ * GE00
  ****************************************************************************/
-struct mv643xx_eth_shared_platform_data loki_ge0_shared_data = {
-	.t_clk		= LOKI_TCLK,
-	.dram		= &loki_mbus_dram_info,
-};
-
-static struct resource loki_ge0_shared_resources[] = {
-	{
-		.name	= "ge0 base",
-		.start	= GE0_PHYS_BASE + 0x2000,
-		.end	= GE0_PHYS_BASE + 0x3fff,
-		.flags	= IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device loki_ge0_shared = {
-	.name		= MV643XX_ETH_SHARED_NAME,
-	.id		= 0,
-	.dev		= {
-		.platform_data	= &loki_ge0_shared_data,
-	},
-	.num_resources	= 1,
-	.resource	= loki_ge0_shared_resources,
-};
-
-static struct resource loki_ge0_resources[] = {
-	{
-		.name	= "ge0 irq",
-		.start	= IRQ_LOKI_GBE_A_INT,
-		.end	= IRQ_LOKI_GBE_A_INT,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device loki_ge0 = {
-	.name		= MV643XX_ETH_NAME,
-	.id		= 0,
-	.num_resources	= 1,
-	.resource	= loki_ge0_resources,
-	.dev		= {
-		.coherent_dma_mask	= 0xffffffff,
-	},
-};
-
 void __init loki_ge0_init(struct mv643xx_eth_platform_data *eth_data)
 {
-	eth_data->shared = &loki_ge0_shared;
-	loki_ge0.dev.platform_data = eth_data;
-
 	writel(0x00079220, GE0_VIRT_BASE + 0x20b0);
-	platform_device_register(&loki_ge0_shared);
-	platform_device_register(&loki_ge0);
+
+	orion_ge00_init(eth_data, &loki_mbus_dram_info,
+			GE0_PHYS_BASE, IRQ_LOKI_GBE_A_INT,
+			0, LOKI_TCLK);
 }
 
 
 /*****************************************************************************
- * GE1
+ * GE01
  ****************************************************************************/
-struct mv643xx_eth_shared_platform_data loki_ge1_shared_data = {
-	.t_clk		= LOKI_TCLK,
-	.dram		= &loki_mbus_dram_info,
-};
-
-static struct resource loki_ge1_shared_resources[] = {
-	{
-		.name	= "ge1 base",
-		.start	= GE1_PHYS_BASE + 0x2000,
-		.end	= GE1_PHYS_BASE + 0x3fff,
-		.flags	= IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device loki_ge1_shared = {
-	.name		= MV643XX_ETH_SHARED_NAME,
-	.id		= 1,
-	.dev		= {
-		.platform_data	= &loki_ge1_shared_data,
-	},
-	.num_resources	= 1,
-	.resource	= loki_ge1_shared_resources,
-};
-
-static struct resource loki_ge1_resources[] = {
-	{
-		.name	= "ge1 irq",
-		.start	= IRQ_LOKI_GBE_B_INT,
-		.end	= IRQ_LOKI_GBE_B_INT,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device loki_ge1 = {
-	.name		= MV643XX_ETH_NAME,
-	.id		= 1,
-	.num_resources	= 1,
-	.resource	= loki_ge1_resources,
-	.dev		= {
-		.coherent_dma_mask	= 0xffffffff,
-	},
-};
-
 void __init loki_ge1_init(struct mv643xx_eth_platform_data *eth_data)
 {
-	eth_data->shared = &loki_ge1_shared;
-	loki_ge1.dev.platform_data = eth_data;
-
 	writel(0x00079220, GE1_VIRT_BASE + 0x20b0);
-	platform_device_register(&loki_ge1_shared);
-	platform_device_register(&loki_ge1);
+
+	orion_ge01_init(eth_data, &loki_mbus_dram_info,
+			GE1_PHYS_BASE, IRQ_LOKI_GBE_B_INT,
+			0, LOKI_TCLK);
 }
 
 
@@ -187,7 +100,7 @@ static struct platform_device loki_sas = {
 	.name		= "mvsas",
 	.id		= 0,
 	.dev		= {
-		.coherent_dma_mask	= 0xffffffff,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
 	},
 	.num_resources	= ARRAY_SIZE(loki_sas_resources),
 	.resource	= loki_sas_resources,
@@ -203,88 +116,19 @@ void __init loki_sas_init(void)
 /*****************************************************************************
  * UART0
  ****************************************************************************/
-static struct plat_serial8250_port loki_uart0_data[] = {
-	{
-		.mapbase	= UART0_PHYS_BASE,
-		.membase	= (char *)UART0_VIRT_BASE,
-		.irq		= IRQ_LOKI_UART0,
-		.flags		= UPF_SKIP_TEST | UPF_BOOT_AUTOCONF,
-		.iotype		= UPIO_MEM,
-		.regshift	= 2,
-		.uartclk	= LOKI_TCLK,
-	}, {
-	},
-};
-
-static struct resource loki_uart0_resources[] = {
-	{
-		.start		= UART0_PHYS_BASE,
-		.end		= UART0_PHYS_BASE + 0xff,
-		.flags		= IORESOURCE_MEM,
-	}, {
-		.start		= IRQ_LOKI_UART0,
-		.end		= IRQ_LOKI_UART0,
-		.flags		= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device loki_uart0 = {
-	.name			= "serial8250",
-	.id			= 0,
-	.dev			= {
-		.platform_data	= loki_uart0_data,
-	},
-	.resource		= loki_uart0_resources,
-	.num_resources		= ARRAY_SIZE(loki_uart0_resources),
-};
-
 void __init loki_uart0_init(void)
 {
-	platform_device_register(&loki_uart0);
+	orion_uart0_init(UART0_VIRT_BASE, UART0_PHYS_BASE,
+			 IRQ_LOKI_UART0, LOKI_TCLK);
 }
 
-
 /*****************************************************************************
  * UART1
  ****************************************************************************/
-static struct plat_serial8250_port loki_uart1_data[] = {
-	{
-		.mapbase	= UART1_PHYS_BASE,
-		.membase	= (char *)UART1_VIRT_BASE,
-		.irq		= IRQ_LOKI_UART1,
-		.flags		= UPF_SKIP_TEST | UPF_BOOT_AUTOCONF,
-		.iotype		= UPIO_MEM,
-		.regshift	= 2,
-		.uartclk	= LOKI_TCLK,
-	}, {
-	},
-};
-
-static struct resource loki_uart1_resources[] = {
-	{
-		.start		= UART1_PHYS_BASE,
-		.end		= UART1_PHYS_BASE + 0xff,
-		.flags		= IORESOURCE_MEM,
-	}, {
-		.start		= IRQ_LOKI_UART1,
-		.end		= IRQ_LOKI_UART1,
-		.flags		= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device loki_uart1 = {
-	.name			= "serial8250",
-	.id			= 1,
-	.dev			= {
-		.platform_data	= loki_uart1_data,
-	},
-	.resource		= loki_uart1_resources,
-	.num_resources		= ARRAY_SIZE(loki_uart1_resources),
-};
-
 void __init loki_uart1_init(void)
 {
-	platform_device_register(&loki_uart1);
+	orion_uart1_init(UART1_VIRT_BASE, UART1_PHYS_BASE,
+			 IRQ_LOKI_UART1, LOKI_TCLK);
 }
 
 

arch/arm/mach-mv78xx0/mpp.c

@@ -12,6 +12,7 @@
 #include <linux/init.h>
 #include <linux/mbus.h>
 #include <linux/io.h>
+#include <plat/mpp.h>
 #include <asm/gpio.h>
 #include <mach/hardware.h>
 #include "common.h"
@@ -31,61 +32,8 @@ static unsigned int __init mv78xx0_variant(void)
 	return 0;
 }
 
-#define MPP_CTRL(i)	(DEV_BUS_VIRT_BASE + (i) * 4)
-#define MPP_NR_REGS	(1 + MPP_MAX/8)
-
 void __init mv78xx0_mpp_conf(unsigned int *mpp_list)
 {
-	u32 mpp_ctrl[MPP_NR_REGS];
-	unsigned int variant_mask;
-	int i;
-
-	variant_mask = mv78xx0_variant();
-	if (!variant_mask)
-		return;
-
-	printk(KERN_DEBUG "initial MPP regs:");
-	for (i = 0; i < MPP_NR_REGS; i++) {
-		mpp_ctrl[i] = readl(MPP_CTRL(i));
-		printk(" %08x", mpp_ctrl[i]);
-	}
-	printk("\n");
-
-	for ( ; *mpp_list; mpp_list++) {
-		unsigned int num = MPP_NUM(*mpp_list);
-		unsigned int sel = MPP_SEL(*mpp_list);
-		int shift, gpio_mode;
-
-		if (num > MPP_MAX) {
-			printk(KERN_ERR "mv78xx0_mpp_conf: invalid MPP "
-					"number (%u)\n", num);
-			continue;
-		}
-		if (!(*mpp_list & variant_mask)) {
-			printk(KERN_WARNING
-					"mv78xx0_mpp_conf: requested MPP%u config "
-					"unavailable on this hardware\n", num);
-			continue;
-		}
-
-		shift = (num & 7) << 2;
-		mpp_ctrl[num / 8] &= ~(0xf << shift);
-		mpp_ctrl[num / 8] |= sel << shift;
-
-		gpio_mode = 0;
-		if (*mpp_list & MPP_INPUT_MASK)
-			gpio_mode |= GPIO_INPUT_OK;
-		if (*mpp_list & MPP_OUTPUT_MASK)
-			gpio_mode |= GPIO_OUTPUT_OK;
-		if (sel != 0)
-			gpio_mode = 0;
-		orion_gpio_set_valid(num, gpio_mode);
-	}
-
-	printk(KERN_DEBUG "  final MPP regs:");
-	for (i = 0; i < MPP_NR_REGS; i++) {
-		writel(mpp_ctrl[i], MPP_CTRL(i));
-		printk(" %08x", mpp_ctrl[i]);
-	}
-	printk("\n");
+	orion_mpp_conf(mpp_list, mv78xx0_variant(),
+		       MPP_MAX, DEV_BUS_VIRT_BASE);
 }

arch/arm/mach-mv78xx0/mpp.h

@@ -19,14 +19,8 @@
     /* may be output signal */    ((!!(_out)) << 13) | \
     /* available on A0 */    ((!!(_78100_A0)) << 14))
 
-#define MPP_NUM(x)    ((x) & 0xff)
-#define MPP_SEL(x)    (((x) >> 8) & 0xf)
-
                 /*   num sel  i  o  78100_A0  */
 
-#define MPP_INPUT_MASK        MPP(0, 0x0, 1, 0, 0)
-#define MPP_OUTPUT_MASK        MPP(0, 0x0, 0, 1, 0)
-
 #define MPP_78100_A0_MASK    MPP(0, 0x0, 0, 0, 1)
 
 #define MPP0_GPIO        MPP(0, 0x0, 1, 1, 1)

arch/arm/mach-orion5x/d2net-setup.c

@@ -267,28 +267,28 @@ static struct platform_device d2net_gpio_buttons = {
  * General Setup
  ****************************************************************************/
 
-static struct orion5x_mpp_mode d2net_mpp_modes[] __initdata = {
-	{  0, MPP_GPIO },	/* Board ID (bit 0) */
-	{  1, MPP_GPIO },	/* Board ID (bit 1) */
-	{  2, MPP_GPIO },	/* Board ID (bit 2) */
-	{  3, MPP_GPIO },	/* SATA 0 power */
-	{  4, MPP_UNUSED },
-	{  5, MPP_GPIO },	/* Fan fail detection */
-	{  6, MPP_GPIO },	/* Red front LED */
-	{  7, MPP_UNUSED },
-	{  8, MPP_GPIO },	/* Rear power switch (on|auto) */
-	{  9, MPP_GPIO },	/* Rear power switch (auto|off) */
-	{ 10, MPP_UNUSED },
-	{ 11, MPP_UNUSED },
-	{ 12, MPP_GPIO },	/* SATA 1 power */
-	{ 13, MPP_UNUSED },
-	{ 14, MPP_SATA_LED },	/* SATA 0 active */
-	{ 15, MPP_SATA_LED },	/* SATA 1 active */
-	{ 16, MPP_GPIO },	/* Blue front LED blink control */
-	{ 17, MPP_UNUSED },
-	{ 18, MPP_GPIO },	/* Front button (0 = Released, 1 = Pushed ) */
-	{ 19, MPP_UNUSED },
-	{ -1 }
+static unsigned int d2net_mpp_modes[] __initdata = {
+	MPP0_GPIO,	/* Board ID (bit 0) */
+	MPP1_GPIO,	/* Board ID (bit 1) */
+	MPP2_GPIO,	/* Board ID (bit 2) */
+	MPP3_GPIO,	/* SATA 0 power */
+	MPP4_UNUSED,
+	MPP5_GPIO,	/* Fan fail detection */
+	MPP6_GPIO,	/* Red front LED */
+	MPP7_UNUSED,
+	MPP8_GPIO,	/* Rear power switch (on|auto) */
+	MPP9_GPIO,	/* Rear power switch (auto|off) */
+	MPP10_UNUSED,
+	MPP11_UNUSED,
+	MPP12_GPIO,	/* SATA 1 power */
+	MPP13_UNUSED,
+	MPP14_SATA_LED,	/* SATA 0 active */
+	MPP15_SATA_LED,	/* SATA 1 active */
+	MPP16_GPIO,	/* Blue front LED blink control */
+	MPP17_UNUSED,
+	MPP18_GPIO,	/* Front button (0 = Released, 1 = Pushed ) */
+	MPP19_UNUSED,
+	0,
 	/* 22: USB port 1 fuse (0 = Fail, 1 = Ok) */
 	/* 23: Blue front LED off */
 	/* 24: Inhibit board power off (0 = Disabled, 1 = Enabled) */

arch/arm/mach-orion5x/db88f5281-setup.c

@@ -298,28 +298,28 @@ static struct i2c_board_info __initdata db88f5281_i2c_rtc = {
 /*****************************************************************************
  * General Setup
  ****************************************************************************/
-static struct orion5x_mpp_mode db88f5281_mpp_modes[] __initdata = {
-	{  0, MPP_GPIO },		/* USB Over Current */
-	{  1, MPP_GPIO },		/* USB Vbat input */
-	{  2, MPP_PCI_ARB },		/* PCI_REQn[2] */
-	{  3, MPP_PCI_ARB },		/* PCI_GNTn[2] */
-	{  4, MPP_PCI_ARB },		/* PCI_REQn[3] */
-	{  5, MPP_PCI_ARB },		/* PCI_GNTn[3] */
-	{  6, MPP_GPIO },		/* JP0, CON17.2 */
-	{  7, MPP_GPIO },		/* JP1, CON17.1 */
-	{  8, MPP_GPIO },		/* JP2, CON11.2 */
-	{  9, MPP_GPIO },		/* JP3, CON11.3 */
-	{ 10, MPP_GPIO },		/* RTC int */
-	{ 11, MPP_GPIO },		/* Baud Rate Generator */
-	{ 12, MPP_GPIO },		/* PCI int 1 */
-	{ 13, MPP_GPIO },		/* PCI int 2 */
-	{ 14, MPP_NAND },		/* NAND_REn[2] */
-	{ 15, MPP_NAND },		/* NAND_WEn[2] */
-	{ 16, MPP_UART },		/* UART1_RX */
-	{ 17, MPP_UART },		/* UART1_TX */
-	{ 18, MPP_UART },		/* UART1_CTSn */
-	{ 19, MPP_UART },		/* UART1_RTSn */
-	{ -1 },
+static unsigned int db88f5281_mpp_modes[] __initdata = {
+	MPP0_GPIO,		/* USB Over Current */
+	MPP1_GPIO,		/* USB Vbat input */
+	MPP2_PCI_ARB,		/* PCI_REQn[2] */
+	MPP3_PCI_ARB,		/* PCI_GNTn[2] */
+	MPP4_PCI_ARB,		/* PCI_REQn[3] */
+	MPP5_PCI_ARB,		/* PCI_GNTn[3] */
+	MPP6_GPIO,		/* JP0, CON17.2 */
+	MPP7_GPIO,		/* JP1, CON17.1 */
+	MPP8_GPIO,		/* JP2, CON11.2 */
+	MPP9_GPIO,		/* JP3, CON11.3 */
+	MPP10_GPIO,		/* RTC int */
+	MPP11_GPIO,		/* Baud Rate Generator */
+	MPP12_GPIO,		/* PCI int 1 */
+	MPP13_GPIO,		/* PCI int 2 */
+	MPP14_NAND,		/* NAND_REn[2] */
+	MPP15_NAND,		/* NAND_WEn[2] */
+	MPP16_UART,		/* UART1_RX */
+	MPP17_UART,		/* UART1_TX */
+	MPP18_UART,		/* UART1_CTSn */
+	MPP19_UART,		/* UART1_RTSn */
+	0,
 };
 
 static void __init db88f5281_init(void)

arch/arm/mach-orion5x/dns323-setup.c

@@ -385,76 +385,76 @@ static struct mv_sata_platform_data dns323_sata_data = {
 /****************************************************************************
  * General Setup
  */
-static struct orion5x_mpp_mode dns323a_mpp_modes[] __initdata = {
-	{  0, MPP_PCIE_RST_OUTn },
-	{  1, MPP_GPIO },		/* right amber LED (sata ch0) */
-	{  2, MPP_GPIO },		/* left amber LED (sata ch1) */
-	{  3, MPP_UNUSED },
-	{  4, MPP_GPIO },		/* power button LED */
-	{  5, MPP_GPIO },		/* power button LED */
-	{  6, MPP_GPIO },		/* GMT G751-2f overtemp */
-	{  7, MPP_GPIO },		/* M41T80 nIRQ/OUT/SQW */
-	{  8, MPP_GPIO },		/* triggers power off */
-	{  9, MPP_GPIO },		/* power button switch */
-	{ 10, MPP_GPIO },		/* reset button switch */
-	{ 11, MPP_UNUSED },
-	{ 12, MPP_UNUSED },
-	{ 13, MPP_UNUSED },
-	{ 14, MPP_UNUSED },
-	{ 15, MPP_UNUSED },
-	{ 16, MPP_UNUSED },
-	{ 17, MPP_UNUSED },
-	{ 18, MPP_UNUSED },
-	{ 19, MPP_UNUSED },
-	{ -1 },
+static unsigned int dns323a_mpp_modes[] __initdata = {
+	MPP0_PCIE_RST_OUTn,
+	MPP1_GPIO,		/* right amber LED (sata ch0) */
+	MPP2_GPIO,		/* left amber LED (sata ch1) */
+	MPP3_UNUSED,
+	MPP4_GPIO,		/* power button LED */
+	MPP5_GPIO,		/* power button LED */
+	MPP6_GPIO,		/* GMT G751-2f overtemp */
+	MPP7_GPIO,		/* M41T80 nIRQ/OUT/SQW */
+	MPP8_GPIO,		/* triggers power off */
+	MPP9_GPIO,		/* power button switch */
+	MPP10_GPIO,		/* reset button switch */
+	MPP11_UNUSED,
+	MPP12_UNUSED,
+	MPP13_UNUSED,
+	MPP14_UNUSED,
+	MPP15_UNUSED,
+	MPP16_UNUSED,
+	MPP17_UNUSED,
+	MPP18_UNUSED,
+	MPP19_UNUSED,
+	0,
 };
 
-static struct orion5x_mpp_mode dns323b_mpp_modes[] __initdata = {
-	{  0, MPP_UNUSED },
-	{  1, MPP_GPIO },		/* right amber LED (sata ch0) */
-	{  2, MPP_GPIO },		/* left amber LED (sata ch1) */
-	{  3, MPP_GPIO },		/* system up flag */
-	{  4, MPP_GPIO },		/* power button LED */
-	{  5, MPP_GPIO },		/* power button LED */
-	{  6, MPP_GPIO },		/* GMT G751-2f overtemp */
-	{  7, MPP_GPIO },		/* M41T80 nIRQ/OUT/SQW */
-	{  8, MPP_GPIO },		/* triggers power off */
-	{  9, MPP_GPIO },		/* power button switch */
-	{ 10, MPP_GPIO },		/* reset button switch */
-	{ 11, MPP_UNUSED },
-	{ 12, MPP_SATA_LED },
-	{ 13, MPP_SATA_LED },
-	{ 14, MPP_SATA_LED },
-	{ 15, MPP_SATA_LED },
-	{ 16, MPP_UNUSED },
-	{ 17, MPP_UNUSED },
-	{ 18, MPP_UNUSED },
-	{ 19, MPP_UNUSED },
-	{ -1 },
+static unsigned int dns323b_mpp_modes[] __initdata = {
+	MPP0_UNUSED,
+	MPP1_GPIO,		/* right amber LED (sata ch0) */
+	MPP2_GPIO,		/* left amber LED (sata ch1) */
+	MPP3_GPIO,		/* system up flag */
+	MPP4_GPIO,		/* power button LED */
+	MPP5_GPIO,		/* power button LED */
+	MPP6_GPIO,		/* GMT G751-2f overtemp */
+	MPP7_GPIO,		/* M41T80 nIRQ/OUT/SQW */
+	MPP8_GPIO,		/* triggers power off */
+	MPP9_GPIO,		/* power button switch */
+	MPP10_GPIO,		/* reset button switch */
+	MPP11_UNUSED,
+	MPP12_SATA_LED,
+	MPP13_SATA_LED,
+	MPP14_SATA_LED,
+	MPP15_SATA_LED,
+	MPP16_UNUSED,
+	MPP17_UNUSED,
+	MPP18_UNUSED,
+	MPP19_UNUSED,
+	0,
 };
 
-static struct orion5x_mpp_mode dns323c_mpp_modes[] __initdata = {
-	{  0, MPP_GPIO },		/* ? input */
-	{  1, MPP_GPIO },		/* input power switch (0 = pressed) */
-	{  2, MPP_GPIO },		/* output power off */
-	{  3, MPP_UNUSED },		/* ? output */
-	{  4, MPP_UNUSED },		/* ? output */
-	{  5, MPP_UNUSED },		/* ? output */
-	{  6, MPP_UNUSED },		/* ? output */
-	{  7, MPP_UNUSED },		/* ? output */
-	{  8, MPP_GPIO },		/* i/o right amber LED */
-	{  9, MPP_GPIO },		/* i/o left amber LED */
-	{ 10, MPP_GPIO },		/* input */
-	{ 11, MPP_UNUSED },
-	{ 12, MPP_SATA_LED },
-	{ 13, MPP_SATA_LED },
-	{ 14, MPP_SATA_LED },
-	{ 15, MPP_SATA_LED },
-	{ 16, MPP_UNUSED },
-	{ 17, MPP_GPIO },		/* power button LED */
-	{ 18, MPP_GPIO },		/* fan speed bit 0 */
-	{ 19, MPP_GPIO },		/* fan speed bit 1 */
-	{ -1 },
+static unsigned int dns323c_mpp_modes[] __initdata = {
+	MPP0_GPIO,		/* ? input */
+	MPP1_GPIO,		/* input power switch (0 = pressed) */
+	MPP2_GPIO,		/* output power off */
+	MPP3_UNUSED,		/* ? output */
+	MPP4_UNUSED,		/* ? output */
+	MPP5_UNUSED,		/* ? output */
+	MPP6_UNUSED,		/* ? output */
+	MPP7_UNUSED,		/* ? output */
+	MPP8_GPIO,		/* i/o right amber LED */
+	MPP9_GPIO,		/* i/o left amber LED */
+	MPP10_GPIO,		/* input */
+	MPP11_UNUSED,
+	MPP12_SATA_LED,
+	MPP13_SATA_LED,
+	MPP14_SATA_LED,
+	MPP15_SATA_LED,
+	MPP16_UNUSED,
+	MPP17_GPIO,		/* power button LED */
+	MPP18_GPIO,		/* fan speed bit 0 */
+	MPP19_GPIO,		/* fan speed bit 1 */
+	0,
 };
 
 /* Rev C1 Fan speed notes:

arch/arm/mach-orion5x/edmini_v2-setup.c

@@ -180,31 +180,31 @@ static struct platform_device edmini_v2_gpio_buttons = {
 /*****************************************************************************
  * General Setup
  ****************************************************************************/
-static struct orion5x_mpp_mode edminiv2_mpp_modes[] __initdata = {
-	{  0, MPP_UNUSED },
-	{  1, MPP_UNUSED },
-	{  2, MPP_UNUSED },
-	{  3, MPP_GPIO },	/* RTC interrupt */
-	{  4, MPP_UNUSED },
-	{  5, MPP_UNUSED },
-	{  6, MPP_UNUSED },
-	{  7, MPP_UNUSED },
-	{  8, MPP_UNUSED },
-	{  9, MPP_UNUSED },
-	{ 10, MPP_UNUSED },
-	{ 11, MPP_UNUSED },
-	{ 12, MPP_SATA_LED },	/* SATA 0 presence */
-	{ 13, MPP_SATA_LED },	/* SATA 1 presence */
-	{ 14, MPP_SATA_LED },	/* SATA 0 active */
-	{ 15, MPP_SATA_LED },	/* SATA 1 active */
+static unsigned int edminiv2_mpp_modes[] __initdata = {
+	MPP0_UNUSED,
+	MPP1_UNUSED,
+	MPP2_UNUSED,
+	MPP3_GPIO,	/* RTC interrupt */
+	MPP4_UNUSED,
+	MPP5_UNUSED,
+	MPP6_UNUSED,
+	MPP7_UNUSED,
+	MPP8_UNUSED,
+	MPP9_UNUSED,
+	MPP10_UNUSED,
+	MPP11_UNUSED,
+	MPP12_SATA_LED,	/* SATA 0 presence */
+	MPP13_SATA_LED,	/* SATA 1 presence */
+	MPP14_SATA_LED,	/* SATA 0 active */
+	MPP15_SATA_LED,	/* SATA 1 active */
 	/* 16: Power LED control (0 = On, 1 = Off) */
-	{ 16, MPP_GPIO },
+	MPP16_GPIO,
 	/* 17: Power LED control select (0 = CPLD, 1 = GPIO16) */
-	{ 17, MPP_GPIO },
+	MPP17_GPIO,
 	/* 18: Power button status (0 = Released, 1 = Pressed) */
-	{ 18, MPP_GPIO },
-	{ 19, MPP_UNUSED },
-	{ -1 }
+	MPP18_GPIO,
+	MPP19_UNUSED,
+	0,
 };
 
 static void __init edmini_v2_init(void)

arch/arm/mach-orion5x/kurobox_pro-setup.c

@@ -315,28 +315,28 @@ static void kurobox_pro_power_off(void)
 /*****************************************************************************
  * General Setup
  ****************************************************************************/
-static struct orion5x_mpp_mode kurobox_pro_mpp_modes[] __initdata = {
-	{  0, MPP_UNUSED },
-	{  1, MPP_UNUSED },
-	{  2, MPP_GPIO },		/* GPIO Micon */
-	{  3, MPP_GPIO },		/* GPIO Rtc */
-	{  4, MPP_UNUSED },
-	{  5, MPP_UNUSED },
-	{  6, MPP_NAND },		/* NAND Flash REn */
-	{  7, MPP_NAND },		/* NAND Flash WEn */
-	{  8, MPP_UNUSED },
-	{  9, MPP_UNUSED },
-	{ 10, MPP_UNUSED },
-	{ 11, MPP_UNUSED },
-	{ 12, MPP_SATA_LED },		/* SATA 0 presence */
-	{ 13, MPP_SATA_LED },		/* SATA 1 presence */
-	{ 14, MPP_SATA_LED },		/* SATA 0 active */
-	{ 15, MPP_SATA_LED },		/* SATA 1 active */
-	{ 16, MPP_UART },		/* UART1 RXD */
-	{ 17, MPP_UART },		/* UART1 TXD */
-	{ 18, MPP_UART },		/* UART1 CTSn */
-	{ 19, MPP_UART },		/* UART1 RTSn */
-	{ -1 },
+static unsigned int kurobox_pro_mpp_modes[] __initdata = {
+	MPP0_UNUSED,
+	MPP1_UNUSED,
+	MPP2_GPIO,		/* GPIO Micon */
+	MPP3_GPIO,		/* GPIO Rtc */
+	MPP4_UNUSED,
+	MPP5_UNUSED,
+	MPP6_NAND,		/* NAND Flash REn */
+	MPP7_NAND,		/* NAND Flash WEn */
+	MPP8_UNUSED,
+	MPP9_UNUSED,
+	MPP10_UNUSED,
+	MPP11_UNUSED,
+	MPP12_SATA_LED,		/* SATA 0 presence */
+	MPP13_SATA_LED,		/* SATA 1 presence */
+	MPP14_SATA_LED,		/* SATA 0 active */
+	MPP15_SATA_LED,		/* SATA 1 active */
+	MPP16_UART,		/* UART1 RXD */
+	MPP17_UART,		/* UART1 TXD */
+	MPP18_UART,		/* UART1 CTSn */
+	MPP19_UART,		/* UART1 RTSn */
+	0,
 };
 
 static void __init kurobox_pro_init(void)

arch/arm/mach-orion5x/ls-chl-setup.c

@@ -251,28 +251,28 @@ static struct platform_device lschl_fan_device = {
  * GPIO Data
  ****************************************************************************/
 
-static struct orion5x_mpp_mode lschl_mpp_modes[] __initdata = {
-	{  0, MPP_GPIO }, /* LED POWER */
-	{  1, MPP_GPIO }, /* HDD POWER */
-	{  2, MPP_GPIO }, /* LED ALARM */
-	{  3, MPP_GPIO }, /* LED INFO */
-	{  4, MPP_UNUSED },
-	{  5, MPP_UNUSED },
-	{  6, MPP_GPIO }, /* FAN LOCK */
-	{  7, MPP_GPIO }, /* SW INIT */
-	{  8, MPP_GPIO }, /* SW POWER */
-	{  9, MPP_GPIO }, /* USB POWER */
-	{ 10, MPP_GPIO }, /* SW AUTO POWER */
-	{ 11, MPP_UNUSED },
-	{ 12, MPP_UNUSED },
-	{ 13, MPP_UNUSED },
-	{ 14, MPP_GPIO }, /* FAN HIGH */
-	{ 15, MPP_GPIO }, /* SW FUNC */
-	{ 16, MPP_GPIO }, /* FAN LOW */
-	{ 17, MPP_GPIO }, /* LED FUNC */
-	{ 18, MPP_UNUSED },
-	{ 19, MPP_UNUSED },
-	{ -1 },
+static unsigned int lschl_mpp_modes[] __initdata = {
+	MPP0_GPIO, /* LED POWER */
+	MPP1_GPIO, /* HDD POWER */
+	MPP2_GPIO, /* LED ALARM */
+	MPP3_GPIO, /* LED INFO */
+	MPP4_UNUSED,
+	MPP5_UNUSED,
+	MPP6_GPIO, /* FAN LOCK */
+	MPP7_GPIO, /* SW INIT */
+	MPP8_GPIO, /* SW POWER */
+	MPP9_GPIO, /* USB POWER */
+	MPP10_GPIO, /* SW AUTO POWER */
+	MPP11_UNUSED,
+	MPP12_UNUSED,
+	MPP13_UNUSED,
+	MPP14_GPIO, /* FAN HIGH */
+	MPP15_GPIO, /* SW FUNC */
+	MPP16_GPIO, /* FAN LOW */
+	MPP17_GPIO, /* LED FUNC */
+	MPP18_UNUSED,
+	MPP19_UNUSED,
+	0,
 };
 
 static void __init lschl_init(void)

arch/arm/mach-orion5x/ls_hgl-setup.c

@@ -200,28 +200,28 @@ static void ls_hgl_power_off(void)
 
 #define LS_HGL_GPIO_HDD_POWER	1
 
-static struct orion5x_mpp_mode ls_hgl_mpp_modes[] __initdata = {
-	{  0, MPP_GPIO }, /* LED_PWR */
-	{  1, MPP_GPIO }, /* HDD_PWR */
-	{  2, MPP_GPIO }, /* LED_ALARM */
-	{  3, MPP_GPIO }, /* LED_INFO */
-	{  4, MPP_UNUSED },
-	{  5, MPP_UNUSED },
-	{  6, MPP_GPIO }, /* FAN_LCK */
-	{  7, MPP_GPIO }, /* INIT */
-	{  8, MPP_GPIO }, /* POWER */
-	{  9, MPP_GPIO }, /* USB_PWR */
-	{ 10, MPP_GPIO }, /* AUTO_POWER */
-	{ 11, MPP_UNUSED }, /* LED_ETH (dummy) */
-	{ 12, MPP_UNUSED },
-	{ 13, MPP_UNUSED },
-	{ 14, MPP_UNUSED },
-	{ 15, MPP_GPIO }, /* FUNC */
-	{ 16, MPP_UNUSED },
-	{ 17, MPP_GPIO }, /* LED_FUNC */
-	{ 18, MPP_UNUSED },
-	{ 19, MPP_UNUSED },
-	{ -1 },
+static unsigned int ls_hgl_mpp_modes[] __initdata = {
+	MPP0_GPIO, /* LED_PWR */
+	MPP1_GPIO, /* HDD_PWR */
+	MPP2_GPIO, /* LED_ALARM */
+	MPP3_GPIO, /* LED_INFO */
+	MPP4_UNUSED,
+	MPP5_UNUSED,
+	MPP6_GPIO, /* FAN_LCK */
+	MPP7_GPIO, /* INIT */
+	MPP8_GPIO, /* POWER */
+	MPP9_GPIO, /* USB_PWR */
+	MPP10_GPIO, /* AUTO_POWER */
+	MPP11_UNUSED, /* LED_ETH (dummy) */
+	MPP12_UNUSED,
+	MPP13_UNUSED,
+	MPP14_UNUSED,
+	MPP15_GPIO, /* FUNC */
+	MPP16_UNUSED,
+	MPP17_GPIO, /* LED_FUNC */
+	MPP18_UNUSED,
+	MPP19_UNUSED,
+	0,
 };
 
 static void __init ls_hgl_init(void)

arch/arm/mach-orion5x/lsmini-setup.c

@@ -201,28 +201,28 @@ static void lsmini_power_off(void)
 #define LSMINI_GPIO_HDD_POWER0	1
 #define LSMINI_GPIO_HDD_POWER1	19
 
-static struct orion5x_mpp_mode lsmini_mpp_modes[] __initdata = {
-	{  0, MPP_UNUSED }, /* LED_RESERVE1 (unused) */
-	{  1, MPP_GPIO }, /* HDD_PWR */
-	{  2, MPP_GPIO }, /* LED_ALARM */
-	{  3, MPP_GPIO }, /* LED_INFO */
-	{  4, MPP_UNUSED },
-	{  5, MPP_UNUSED },
-	{  6, MPP_UNUSED },
-	{  7, MPP_UNUSED },
-	{  8, MPP_UNUSED },
-	{  9, MPP_GPIO }, /* LED_FUNC */
-	{ 10, MPP_UNUSED },
-	{ 11, MPP_UNUSED }, /* LED_ETH (dummy) */
-	{ 12, MPP_UNUSED },
-	{ 13, MPP_UNUSED },
-	{ 14, MPP_GPIO }, /* LED_PWR */
-	{ 15, MPP_GPIO }, /* FUNC */
-	{ 16, MPP_GPIO }, /* USB_PWR */
-	{ 17, MPP_GPIO }, /* AUTO_POWER */
-	{ 18, MPP_GPIO }, /* POWER */
-	{ 19, MPP_GPIO }, /* HDD_PWR1 */
-	{ -1 },
+static unsigned int lsmini_mpp_modes[] __initdata = {
+	MPP0_UNUSED, /* LED_RESERVE1 (unused) */
+	MPP1_GPIO, /* HDD_PWR */
+	MPP2_GPIO, /* LED_ALARM */
+	MPP3_GPIO, /* LED_INFO */
+	MPP4_UNUSED,
+	MPP5_UNUSED,
+	MPP6_UNUSED,
+	MPP7_UNUSED,
+	MPP8_UNUSED,
+	MPP9_GPIO, /* LED_FUNC */
+	MPP10_UNUSED,
+	MPP11_UNUSED, /* LED_ETH (dummy) */
+	MPP12_UNUSED,
+	MPP13_UNUSED,
+	MPP14_GPIO, /* LED_PWR */
+	MPP15_GPIO, /* FUNC */
+	MPP16_GPIO, /* USB_PWR */
+	MPP17_GPIO, /* AUTO_POWER */
+	MPP18_GPIO, /* POWER */
+	MPP19_GPIO, /* HDD_PWR1 */
+	0,
 };
 
 static void __init lsmini_init(void)

arch/arm/mach-orion5x/mpp.c

@@ -12,154 +12,34 @@
 #include <linux/init.h>
 #include <linux/mbus.h>
 #include <linux/io.h>
-#include <asm/gpio.h>
 #include <mach/hardware.h>
-#include "common.h"
+#include <plat/mpp.h>
 #include "mpp.h"
+#include "common.h"
 
-static int is_5181l(void)
-{
-	u32 dev;
-	u32 rev;
-
-	orion5x_pcie_id(&dev, &rev);
-
-	return !!(dev == MV88F5181_DEV_ID && rev >= MV88F5181L_REV_A0);
-}
-
-static int is_5182(void)
-{
-	u32 dev;
-	u32 rev;
-
-	orion5x_pcie_id(&dev, &rev);
-
-	return !!(dev == MV88F5182_DEV_ID);
-}
-
-static int is_5281(void)
+static unsigned int __init orion5x_variant(void)
 {
 	u32 dev;
 	u32 rev;
 
 	orion5x_pcie_id(&dev, &rev);
 
-	return !!(dev == MV88F5281_DEV_ID);
-}
-
-static int __init determine_type_encoding(int mpp, enum orion5x_mpp_type type)
-{
-	switch (type) {
-	case MPP_UNUSED:
-	case MPP_GPIO:
-		if (mpp == 0)
-			return 3;
-		if (mpp >= 1 && mpp <= 15)
-			return 0;
-		if (mpp >= 16 && mpp <= 19) {
-			if (is_5182())
-				return 5;
-			if (type == MPP_UNUSED)
-				return 0;
-		}
-		return -1;
-
-	case MPP_PCIE_RST_OUTn:
-		if (mpp == 0)
-			return 0;
-		return -1;
-
-	case MPP_PCI_ARB:
-		if (mpp >= 0 && mpp <= 7)
-			return 2;
-		return -1;
-
-	case MPP_PCI_PMEn:
-		if (mpp == 2)
-			return 3;
-		return -1;
-
-	case MPP_GIGE:
-		if (mpp >= 8 && mpp <= 19)
-			return 1;
-		return -1;
-
-	case MPP_NAND:
-		if (is_5182() || is_5281()) {
-			if (mpp >= 4 && mpp <= 7)
-				return 4;
-			if (mpp >= 12 && mpp <= 17)
-				return 4;
-		}
-		return -1;
+	if (dev == MV88F5181_DEV_ID && rev >= MV88F5181L_REV_A0)
+		return MPP_F5181_MASK;
 
-	case MPP_PCI_CLK:
-		if (is_5181l() && mpp >= 6 && mpp <= 7)
-			return 5;
-		return -1;
+	if (dev == MV88F5182_DEV_ID)
+		return MPP_F5182_MASK;
 
-	case MPP_SATA_LED:
-		if (is_5182()) {
-			if (mpp >= 4 && mpp <= 7)
-				return 5;
-			if (mpp >= 12 && mpp <= 15)
-				return 5;
-		}
-		return -1;
+	if (dev == MV88F5281_DEV_ID)
+		return MPP_F5281_MASK;
 
-	case MPP_UART:
-		if (mpp >= 16 && mpp <= 19)
+	printk(KERN_ERR "MPP setup: unknown orion5x variant "
+	       "(dev %#x rev %#x)\n", dev, rev);
 	return 0;
-		return -1;
-	}
-
-	printk(KERN_INFO "unknown MPP type %d\n", type);
-
-	return -1;
 }
 
-void __init orion5x_mpp_conf(struct orion5x_mpp_mode *mode)
+void __init orion5x_mpp_conf(unsigned int *mpp_list)
 {
-	u32 mpp_0_7_ctrl = readl(MPP_0_7_CTRL);
-	u32 mpp_8_15_ctrl = readl(MPP_8_15_CTRL);
-	u32 mpp_16_19_ctrl = readl(MPP_16_19_CTRL);
-
-	for ( ; mode->mpp >= 0; mode++) {
-		u32 *reg;
-		int num_type;
-		int shift;
-
-		if (mode->mpp >= 0 && mode->mpp <= 7)
-			reg = &mpp_0_7_ctrl;
-		else if (mode->mpp >= 8 && mode->mpp <= 15)
-			reg = &mpp_8_15_ctrl;
-		else if (mode->mpp >= 16 && mode->mpp <= 19)
-			reg = &mpp_16_19_ctrl;
-		else {
-			printk(KERN_ERR "orion5x_mpp_conf: invalid MPP "
-					"(%d)\n", mode->mpp);
-			continue;
-		}
-
-		num_type = determine_type_encoding(mode->mpp, mode->type);
-		if (num_type < 0) {
-			printk(KERN_ERR "orion5x_mpp_conf: invalid MPP "
-					"combination (%d, %d)\n", mode->mpp,
-					mode->type);
-			continue;
-		}
-
-		shift = (mode->mpp & 7) << 2;
-		*reg &= ~(0xf << shift);
-		*reg |= (num_type & 0xf) << shift;
-
-		if (mode->type == MPP_UNUSED && (mode->mpp < 16 || is_5182()))
-			orion_gpio_set_unused(mode->mpp);
-
-		orion_gpio_set_valid(mode->mpp, !!(mode->type == MPP_GPIO));
-	}
-
-	writel(mpp_0_7_ctrl, MPP_0_7_CTRL);
-	writel(mpp_8_15_ctrl, MPP_8_15_CTRL);
-	writel(mpp_16_19_ctrl, MPP_16_19_CTRL);
+	orion_mpp_conf(mpp_list, orion5x_variant(),
+		       MPP_MAX, ORION5X_DEV_BUS_VIRT_BASE);
 }

arch/arm/mach-orion5x/mpp.h

 #ifndef __ARCH_ORION5X_MPP_H
 #define __ARCH_ORION5X_MPP_H
 
-enum orion5x_mpp_type {
-	/*
-	 * This MPP is unused.
-	 */
-	MPP_UNUSED,
-
-	/*
-	 * This MPP pin is used as a generic GPIO pin.  Valid for
-	 * MPPs 0-15 and device bus data pins 16-31.  On 5182, also
-	 * valid for MPPs 16-19.
-	 */
-	MPP_GPIO,
-
-	/*
-	 * This MPP is used as PCIe_RST_OUTn pin.  Valid for
-	 * MPP 0 only.
-	 */
-	MPP_PCIE_RST_OUTn,
-
-	/*
-	 * This MPP is used as PCI arbiter pin (REQn/GNTn).
-	 * Valid for MPPs 0-7 only.
-	 */
-	MPP_PCI_ARB,
-
-	/*
-	 * This MPP is used as PCI_PMEn pin.  Valid for MPP 2 only.
-	 */
-	MPP_PCI_PMEn,
-
-	/*
-	 * This MPP is used as GigE half-duplex (COL, CRS) or GMII
-	 * (RXERR, CRS, TXERR, TXD[7:4], RXD[7:4]) pin.  Valid for
-	 * MPPs 8-19 only.
-	 */
-	MPP_GIGE,
-
-	/*
-	 * This MPP is used as NAND REn/WEn pin.  Valid for MPPs
-	 * 4-7 and 12-17 only, and only on the 5181l/5182/5281.
-	 */
-	MPP_NAND,
-
-	/*
-	 * This MPP is used as a PCI clock output pin.  Valid for
-	 * MPPs 6-7 only, and only on the 5181l.
-	 */
-	MPP_PCI_CLK,
-
-	/*
-	 * This MPP is used as a SATA presence/activity LED.
-	 * Valid for MPPs 4-7 and 12-15 only, and only on the 5182.
-	 */
-	MPP_SATA_LED,
-
-	/*
-	 * This MPP is used as UART1 RXD/TXD/CTSn/RTSn pin.
-	 * Valid for MPPs 16-19 only.
-	 */
-	MPP_UART,
-};
-
-struct orion5x_mpp_mode {
-	int			mpp;
-	enum orion5x_mpp_type	type;
-};
-
-void orion5x_mpp_conf(struct orion5x_mpp_mode *mode);
+#define MPP(_num, _sel, _in, _out, _F5181l, _F5182, _F5281) ( \
+	/* MPP number */		((_num) & 0xff) | \
+	/* MPP select value */		(((_sel) & 0xf) << 8) | \
+	/* may be input signal */	((!!(_in)) << 12) | \
+	/* may be output signal */	((!!(_out)) << 13) | \
+	/* available on F5181l */	((!!(_F5181l)) << 14) | \
+	/* available on F5182 */	((!!(_F5182)) << 15) | \
+	/* available on F5281 */	((!!(_F5281)) << 16))
 
+				/* num sel  i  o  5181 5182 5281 */
+
+#define MPP_F5181_MASK		MPP(0,  0x0, 0, 0, 1,   0,   0)
+#define MPP_F5182_MASK		MPP(0,  0x0, 0, 0, 0,   1,   0)
+#define MPP_F5281_MASK		MPP(0,  0x0, 0, 0, 0,   0,   1)
+
+#define MPP0_UNUSED	        MPP(0,  0x3, 0, 0, 1,   1,   1)
+#define MPP0_GPIO		MPP(0,  0x3, 1, 1, 1,   1,   1)
+#define MPP0_PCIE_RST_OUTn	MPP(0,  0x0, 0, 0, 1,   1,   1)
+#define MPP0_PCI_ARB            MPP(0,  0x2, 0, 0, 1,   1,   1)
+
+#define MPP1_UNUSED		MPP(1,  0x0, 0, 0, 1,   1,   1)
+#define MPP1_GPIO		MPP(1,  0x0, 1, 1, 1,   1,   1)
+#define MPP1_PCI_ARB            MPP(1,  0x2, 0, 0, 1,   1,   1)
+
+#define MPP2_UNUSED		MPP(2,  0x0, 0, 0, 1,   1,   1)
+#define MPP2_GPIO		MPP(2,  0x0, 1, 1, 1,   1,   1)
+#define MPP2_PCI_ARB            MPP(2,  0x2, 0, 0, 1,   1,   1)
+#define MPP2_PCI_PMEn           MPP(2,  0x3, 0, 0, 1,   1,   1)
+
+#define MPP3_UNUSED		MPP(3,  0x0, 0, 0, 1,   1,   1)
+#define MPP3_GPIO		MPP(3,  0x0, 1, 1, 1,   1,   1)
+#define MPP3_PCI_ARB            MPP(3,  0x2, 0, 0, 1,   1,   1)
+
+#define MPP4_UNUSED		MPP(4,  0x0, 0, 0, 1,   1,   1)
+#define MPP4_GPIO		MPP(4,  0x0, 1, 1, 1,   1,   1)
+#define MPP4_PCI_ARB            MPP(4,  0x2, 0, 0, 1,   1,   1)
+#define MPP4_NAND               MPP(4,  0x4, 0, 0, 0,   1,   1)
+#define MPP4_SATA_LED           MPP(4,  0x5, 0, 0, 0,   1,   0)
+
+#define MPP5_UNUSED		MPP(5,  0x0, 0, 0, 1,   1,   1)
+#define MPP5_GPIO		MPP(5,  0x0, 1, 1, 1,   1,   1)
+#define MPP5_PCI_ARB            MPP(5,  0x2, 0, 0, 1,   1,   1)
+#define MPP5_NAND               MPP(5,  0x4, 0, 0, 0,   1,   1)
+#define MPP5_SATA_LED           MPP(5,  0x5, 0, 0, 0,   1,   0)
+
+#define MPP6_UNUSED		MPP(6,  0x0, 0, 0, 1,   1,   1)
+#define MPP6_GPIO		MPP(6,  0x0, 1, 1, 1,   1,   1)
+#define MPP6_PCI_ARB            MPP(6,  0x2, 0, 0, 1,   1,   1)
+#define MPP6_NAND               MPP(6,  0x4, 0, 0, 0,   1,   1)
+#define MPP6_PCI_CLK            MPP(6,  0x5, 0, 0, 1,   0,   0)
+#define MPP6_SATA_LED           MPP(6,  0x5, 0, 0, 0,   1,   0)
+
+#define MPP7_UNUSED		MPP(7,  0x0, 0, 0, 1,   1,   1)
+#define MPP7_GPIO		MPP(7,  0x0, 1, 1, 1,   1,   1)
+#define MPP7_PCI_ARB            MPP(7,  0x2, 0, 0, 1,   1,   1)
+#define MPP7_NAND               MPP(7,  0x4, 0, 0, 0,   1,   1)
+#define MPP7_PCI_CLK            MPP(7,  0x5, 0, 0, 1,   0,   0)
+#define MPP7_SATA_LED           MPP(7,  0x5, 0, 0, 0,   1,   0)
+
+#define MPP8_UNUSED		MPP(8,  0x0, 0, 0, 1,   1,   1)
+#define MPP8_GPIO		MPP(8,  0x0, 1, 1, 1,   1,   1)
+#define MPP8_GIGE               MPP(8,  0x1, 0, 0, 1,   1,   1)
+
+#define MPP9_UNUSED		MPP(9,  0x0, 0, 0, 1,   1,   1)
+#define MPP9_GPIO		MPP(9,  0x0, 0, 0, 1,   1,   1)
+#define MPP9_GIGE               MPP(9,  0x1, 1, 1, 1,   1,   1)
+
+#define MPP10_UNUSED		MPP(10, 0x0, 0, 0, 1,   1,   1)
+#define MPP10_GPIO		MPP(10, 0x0, 1, 1, 1,   1,   1)
+#define MPP10_GIGE              MPP(10, 0x1, 0, 0, 1,   1,   1)
+
+#define MPP11_UNUSED		MPP(11, 0x0, 0, 0, 1,   1,   1)
+#define MPP11_GPIO		MPP(11, 0x0, 1, 1, 1,   1,   1)
+#define MPP11_GIGE              MPP(11, 0x1, 0, 0, 1,   1,   1)
+
+#define MPP12_UNUSED		MPP(12, 0x0, 0, 0, 1,   1,   1)
+#define MPP12_GPIO		MPP(12, 0x0, 1, 1, 1,   1,   1)
+#define MPP12_GIGE              MPP(12, 0x1, 0, 0, 1,   1,   1)
+#define MPP12_NAND              MPP(12, 0x4, 0, 0, 0,   1,   1)
+#define MPP12_SATA_LED          MPP(12, 0x5, 0, 0, 0,   1,   0)
+
+#define MPP13_UNUSED		MPP(13, 0x0, 0, 0, 1,   1,   1)
+#define MPP13_GPIO		MPP(13, 0x0, 1, 1, 1,   1,   1)
+#define MPP13_GIGE              MPP(13, 0x1, 0, 0, 1,   1,   1)
+#define MPP13_NAND              MPP(13, 0x4, 0, 0, 0,   1,   1)
+#define MPP13_SATA_LED          MPP(13, 0x5, 0, 0, 0,   1,   0)
+
+#define MPP14_UNUSED		MPP(14, 0x0, 0, 0, 1,   1,   1)
+#define MPP14_GPIO		MPP(14, 0x0, 1, 1, 1,   1,   1)
+#define MPP14_GIGE              MPP(14, 0x1, 0, 0, 1,   1,   1)
+#define MPP14_NAND              MPP(14, 0x4, 0, 0, 0,   1,   1)
+#define MPP14_SATA_LED          MPP(14, 0x5, 0, 0, 0,   1,   0)
+
+#define MPP15_UNUSED		MPP(15, 0x0, 0, 0, 1,   1,   1)
+#define MPP15_GPIO		MPP(15, 0x0, 1, 1, 1,   1,   1)
+#define MPP15_GIGE              MPP(15, 0x1, 0, 0, 1,   1,   1)
+#define MPP15_NAND              MPP(15, 0x4, 0, 0, 0,   1,   1)
+#define MPP15_SATA_LED          MPP(15, 0x5, 0, 0, 0,   1,   0)
+
+#define MPP16_UNUSED		MPP(16, 0x0, 0, 0, 1,   1,   1)
+#define MPP16_GPIO		MPP(16, 0x5, 1, 1, 0,   1,   0)
+#define MPP16_GIGE              MPP(16, 0x1, 0, 0, 1,   1,   1)
+#define MPP16_NAND              MPP(16, 0x4, 0, 0, 0,   1,   1)
+#define MPP16_UART              MPP(16, 0x0, 0, 0, 0,   1,   1)
+
+#define MPP17_UNUSED		MPP(17, 0x0, 0, 0, 1,   1,   1)
+#define MPP17_GPIO		MPP(17, 0x5, 1, 1, 0,   1,   0)
+#define MPP17_GIGE              MPP(17, 0x1, 0, 0, 1,   1,   1)
+#define MPP17_NAND              MPP(17, 0x4, 0, 0, 0,   1,   1)
+#define MPP17_UART              MPP(17, 0x0, 0, 0, 0,   1,   1)
+
+#define MPP18_UNUSED		MPP(18, 0x0, 0, 0, 1,   1,   1)
+#define MPP18_GPIO		MPP(18, 0x5, 1, 1, 0,   1,   0)
+#define MPP18_GIGE              MPP(18, 0x1, 0, 0, 1,   1,   1)
+#define MPP18_UART              MPP(18, 0x0, 0, 0, 0,   1,   1)
+
+#define MPP19_UNUSED		MPP(19, 0x0, 0, 0, 1,   1,   1)
+#define MPP19_GPIO		MPP(19, 0x5, 1, 1, 0,   1,   0)
+#define MPP19_GIGE              MPP(19, 0x1, 0, 0, 1,   1,   1)
+#define MPP19_UART              MPP(19, 0x0, 0, 0, 0,   1,   1)
+
+#define MPP_MAX			19
+
+void orion5x_mpp_conf(unsigned int *mpp_list);
 
 #endif

arch/arm/mach-orion5x/mss2-setup.c

@@ -193,28 +193,28 @@ static void mss2_power_off(void)
 /****************************************************************************
  * General Setup
  ****************************************************************************/
-static struct orion5x_mpp_mode mss2_mpp_modes[] __initdata = {
-	{  0, MPP_GPIO },		/* Power LED */
-	{  1, MPP_GPIO },		/* Error LED */
-	{  2, MPP_UNUSED },
-	{  3, MPP_GPIO },		/* RTC interrupt */
-	{  4, MPP_GPIO },		/* HDD ind. (Single/Dual)*/
-	{  5, MPP_GPIO },		/* HD0 5V control */
-	{  6, MPP_GPIO },		/* HD0 12V control */
-	{  7, MPP_GPIO },		/* HD1 5V control */
-	{  8, MPP_GPIO },		/* HD1 12V control */
-	{  9, MPP_UNUSED },
-	{ 10, MPP_GPIO },		/* Fan control */
-	{ 11, MPP_GPIO },		/* Power button */
-	{ 12, MPP_GPIO },		/* Reset button */
-	{ 13, MPP_UNUSED },
-	{ 14, MPP_SATA_LED },		/* SATA 0 active */
-	{ 15, MPP_SATA_LED },		/* SATA 1 active */
-	{ 16, MPP_UNUSED },
-	{ 17, MPP_UNUSED },
-	{ 18, MPP_UNUSED },
-	{ 19, MPP_UNUSED },
-	{ -1 },
+static unsigned int mss2_mpp_modes[] __initdata = {
+	MPP0_GPIO,		/* Power LED */
+	MPP1_GPIO,		/* Error LED */
+	MPP2_UNUSED,
+	MPP3_GPIO,		/* RTC interrupt */
+	MPP4_GPIO,		/* HDD ind. (Single/Dual)*/
+	MPP5_GPIO,		/* HD0 5V control */
+	MPP6_GPIO,		/* HD0 12V control */
+	MPP7_GPIO,		/* HD1 5V control */
+	MPP8_GPIO,		/* HD1 12V control */
+	MPP9_UNUSED,
+	MPP10_GPIO,		/* Fan control */
+	MPP11_GPIO,		/* Power button */
+	MPP12_GPIO,		/* Reset button */
+	MPP13_UNUSED,
+	MPP14_SATA_LED,		/* SATA 0 active */
+	MPP15_SATA_LED,		/* SATA 1 active */
+	MPP16_UNUSED,
+	MPP17_UNUSED,
+	MPP18_UNUSED,
+	MPP19_UNUSED,
+	0,
 };
 
 static void __init mss2_init(void)

arch/arm/mach-orion5x/mv2120-setup.c

@@ -108,28 +108,28 @@ static struct platform_device mv2120_button_device = {
 /****************************************************************************
  * General Setup
  ****************************************************************************/
-static struct orion5x_mpp_mode mv2120_mpp_modes[] __initdata = {
-	{  0, MPP_GPIO },		/* Sys status LED */
-	{  1, MPP_GPIO },		/* Sys error LED */
-	{  2, MPP_GPIO },		/* OverTemp interrupt */
-	{  3, MPP_GPIO },		/* RTC interrupt */
-	{  4, MPP_GPIO },		/* V_LED 5V */
-	{  5, MPP_GPIO },		/* V_LED 3.3V */
-	{  6, MPP_UNUSED },
-	{  7, MPP_UNUSED },
-	{  8, MPP_GPIO },		/* SATA 0 fail LED */
-	{  9, MPP_GPIO },		/* SATA 1 fail LED */
-	{ 10, MPP_UNUSED },
-	{ 11, MPP_UNUSED },
-	{ 12, MPP_SATA_LED },		/* SATA 0 presence */
-	{ 13, MPP_SATA_LED },		/* SATA 1 presence */
-	{ 14, MPP_SATA_LED },		/* SATA 0 active */
-	{ 15, MPP_SATA_LED },		/* SATA 1 active */
-	{ 16, MPP_UNUSED },
-	{ 17, MPP_GPIO },		/* Reset button */
-	{ 18, MPP_GPIO },		/* Power button */
-	{ 19, MPP_GPIO },		/* Power off */
-	{ -1 },
+static unsigned int mv2120_mpp_modes[] __initdata = {
+	MPP0_GPIO,		/* Sys status LED */
+	MPP1_GPIO,		/* Sys error LED */
+	MPP2_GPIO,		/* OverTemp interrupt */
+	MPP3_GPIO,		/* RTC interrupt */
+	MPP4_GPIO,		/* V_LED 5V */
+	MPP5_GPIO,		/* V_LED 3.3V */
+	MPP6_UNUSED,
+	MPP7_UNUSED,
+	MPP8_GPIO,		/* SATA 0 fail LED */
+	MPP9_GPIO,		/* SATA 1 fail LED */
+	MPP10_UNUSED,
+	MPP11_UNUSED,
+	MPP12_SATA_LED,		/* SATA 0 presence */
+	MPP13_SATA_LED,		/* SATA 1 presence */
+	MPP14_SATA_LED,		/* SATA 0 active */
+	MPP15_SATA_LED,		/* SATA 1 active */
+	MPP16_UNUSED,
+	MPP17_GPIO,		/* Reset button */
+	MPP18_GPIO,		/* Power button */
+	MPP19_GPIO,		/* Power off */
+	0,
 };
 
 static struct i2c_board_info __initdata mv2120_i2c_rtc = {

arch/arm/mach-orion5x/net2big-setup.c

@@ -339,28 +339,28 @@ static struct platform_device net2big_gpio_buttons = {
  * General Setup
  ****************************************************************************/
 
-static struct orion5x_mpp_mode net2big_mpp_modes[] __initdata = {
-	{  0, MPP_GPIO },	/* Raid mode (bit 0) */
-	{  1, MPP_GPIO },	/* USB port 2 fuse (0 = Fail, 1 = Ok) */
-	{  2, MPP_GPIO },	/* Raid mode (bit 1) */
-	{  3, MPP_GPIO },	/* Board ID (bit 0) */
-	{  4, MPP_GPIO },	/* Fan activity (0 = Off, 1 = On) */
-	{  5, MPP_GPIO },	/* Fan fail detection */
-	{  6, MPP_GPIO },	/* Red front LED (0 = Off, 1 = On) */
-	{  7, MPP_GPIO },	/* Disable initial blinking on front LED */
-	{  8, MPP_GPIO },	/* Rear power switch (on|auto) */
-	{  9, MPP_GPIO },	/* Rear power switch (auto|off) */
-	{ 10, MPP_GPIO },	/* SATA 1 red LED (0 = Off, 1 = On) */
-	{ 11, MPP_GPIO },	/* SATA 0 red LED (0 = Off, 1 = On) */
-	{ 12, MPP_GPIO },	/* Board ID (bit 1) */
-	{ 13, MPP_GPIO },	/* SATA 1 blue LED blink control */
-	{ 14, MPP_SATA_LED },
-	{ 15, MPP_SATA_LED },
-	{ 16, MPP_GPIO },	/* Blue front LED control */
-	{ 17, MPP_GPIO },	/* SATA 0 blue LED blink control */
-	{ 18, MPP_GPIO },	/* Front button (0 = Released, 1 = Pushed ) */
-	{ 19, MPP_GPIO },	/* SATA{0,1} power On/Off request */
-	{ -1 }
+static unsigned int net2big_mpp_modes[] __initdata = {
+	MPP0_GPIO,	/* Raid mode (bit 0) */
+	MPP1_GPIO,	/* USB port 2 fuse (0 = Fail, 1 = Ok) */
+	MPP2_GPIO,	/* Raid mode (bit 1) */
+	MPP3_GPIO,	/* Board ID (bit 0) */
+	MPP4_GPIO,	/* Fan activity (0 = Off, 1 = On) */
+	MPP5_GPIO,	/* Fan fail detection */
+	MPP6_GPIO,	/* Red front LED (0 = Off, 1 = On) */
+	MPP7_GPIO,	/* Disable initial blinking on front LED */
+	MPP8_GPIO,	/* Rear power switch (on|auto) */
+	MPP9_GPIO,	/* Rear power switch (auto|off) */
+	MPP10_GPIO,	/* SATA 1 red LED (0 = Off, 1 = On) */
+	MPP11_GPIO,	/* SATA 0 red LED (0 = Off, 1 = On) */
+	MPP12_GPIO,	/* Board ID (bit 1) */
+	MPP13_GPIO,	/* SATA 1 blue LED blink control */
+	MPP14_SATA_LED,
+	MPP15_SATA_LED,
+	MPP16_GPIO,	/* Blue front LED control */
+	MPP17_GPIO,	/* SATA 0 blue LED blink control */
+	MPP18_GPIO,	/* Front button (0 = Released, 1 = Pushed ) */
+	MPP19_GPIO,	/* SATA{0,1} power On/Off request */
+	0,
 	/* 22: USB port 1 fuse (0 = Fail, 1 = Ok) */
 	/* 23: SATA 0 power status */
 	/* 24: Board power off */

arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c

@@ -64,28 +64,28 @@ static struct platform_device rd88f5181l_fxo_nor_boot_flash = {
 /*****************************************************************************
  * General Setup
  ****************************************************************************/
-static struct orion5x_mpp_mode rd88f5181l_fxo_mpp_modes[] __initdata = {
-	{  0, MPP_GPIO },		/* LED1 CardBus LED (front panel) */
-	{  1, MPP_GPIO },		/* PCI_intA */
-	{  2, MPP_GPIO },		/* Hard Reset / Factory Init*/
-	{  3, MPP_GPIO },		/* FXS or DAA select */
-	{  4, MPP_GPIO },		/* LED6 - phone LED (front panel) */
-	{  5, MPP_GPIO },		/* LED5 - phone LED (front panel) */
-	{  6, MPP_PCI_CLK },		/* CPU PCI refclk */
-	{  7, MPP_PCI_CLK },		/* PCI/PCIe refclk */
-	{  8, MPP_GPIO },		/* CardBus reset */
-	{  9, MPP_GPIO },		/* GE_RXERR */
-	{ 10, MPP_GPIO },		/* LED2 MiniPCI LED (front panel) */
-	{ 11, MPP_GPIO },		/* Lifeline control */
-	{ 12, MPP_GIGE },		/* GE_TXD[4] */
-	{ 13, MPP_GIGE },		/* GE_TXD[5] */
-	{ 14, MPP_GIGE },		/* GE_TXD[6] */
-	{ 15, MPP_GIGE },		/* GE_TXD[7] */
-	{ 16, MPP_GIGE },		/* GE_RXD[4] */
-	{ 17, MPP_GIGE },		/* GE_RXD[5] */
-	{ 18, MPP_GIGE },		/* GE_RXD[6] */
-	{ 19, MPP_GIGE },		/* GE_RXD[7] */
-	{ -1 },
+static unsigned int rd88f5181l_fxo_mpp_modes[] __initdata = {
+	MPP0_GPIO,		/* LED1 CardBus LED (front panel) */
+	MPP1_GPIO,		/* PCI_intA */
+	MPP2_GPIO,		/* Hard Reset / Factory Init*/
+	MPP3_GPIO,		/* FXS or DAA select */
+	MPP4_GPIO,		/* LED6 - phone LED (front panel) */
+	MPP5_GPIO,		/* LED5 - phone LED (front panel) */
+	MPP6_PCI_CLK,		/* CPU PCI refclk */
+	MPP7_PCI_CLK,		/* PCI/PCIe refclk */
+	MPP8_GPIO,		/* CardBus reset */
+	MPP9_GPIO,		/* GE_RXERR */
+	MPP10_GPIO,		/* LED2 MiniPCI LED (front panel) */
+	MPP11_GPIO,		/* Lifeline control */
+	MPP12_GIGE,		/* GE_TXD[4] */
+	MPP13_GIGE,		/* GE_TXD[5] */
+	MPP14_GIGE,		/* GE_TXD[6] */
+	MPP15_GIGE,		/* GE_TXD[7] */
+	MPP16_GIGE,		/* GE_RXD[4] */
+	MPP17_GIGE,		/* GE_RXD[5] */
+	MPP18_GIGE,		/* GE_RXD[6] */
+	MPP19_GIGE,		/* GE_RXD[7] */
+	0,
 };
 
 static struct mv643xx_eth_platform_data rd88f5181l_fxo_eth_data = {

arch/arm/mach-orion5x/rd88f5181l-ge-setup.c

@@ -65,28 +65,28 @@ static struct platform_device rd88f5181l_ge_nor_boot_flash = {
 /*****************************************************************************
  * General Setup
  ****************************************************************************/
-static struct orion5x_mpp_mode rd88f5181l_ge_mpp_modes[] __initdata = {
-	{  0, MPP_GPIO },		/* LED1 */
-	{  1, MPP_GPIO },		/* LED5 */
-	{  2, MPP_GPIO },		/* LED4 */
-	{  3, MPP_GPIO },		/* LED3 */
-	{  4, MPP_GPIO },		/* PCI_intA */
-	{  5, MPP_GPIO },		/* RTC interrupt */
-	{  6, MPP_PCI_CLK },		/* CPU PCI refclk */
-	{  7, MPP_PCI_CLK },		/* PCI/PCIe refclk */
-	{  8, MPP_GPIO },		/* 88e6131 interrupt */
-	{  9, MPP_GPIO },		/* GE_RXERR */
-	{ 10, MPP_GPIO },		/* PCI_intB */
-	{ 11, MPP_GPIO },		/* LED2 */
-	{ 12, MPP_GIGE },		/* GE_TXD[4] */
-	{ 13, MPP_GIGE },		/* GE_TXD[5] */
-	{ 14, MPP_GIGE },		/* GE_TXD[6] */
-	{ 15, MPP_GIGE },		/* GE_TXD[7] */
-	{ 16, MPP_GIGE },		/* GE_RXD[4] */
-	{ 17, MPP_GIGE },		/* GE_RXD[5] */
-	{ 18, MPP_GIGE },		/* GE_RXD[6] */
-	{ 19, MPP_GIGE },		/* GE_RXD[7] */
-	{ -1 },
+static unsigned int rd88f5181l_ge_mpp_modes[] __initdata = {
+	MPP0_GPIO,		/* LED1 */
+	MPP1_GPIO,		/* LED5 */
+	MPP2_GPIO,		/* LED4 */
+	MPP3_GPIO,		/* LED3 */
+	MPP4_GPIO,		/* PCI_intA */
+	MPP5_GPIO,		/* RTC interrupt */
+	MPP6_PCI_CLK,		/* CPU PCI refclk */
+	MPP7_PCI_CLK,		/* PCI/PCIe refclk */
+	MPP8_GPIO,		/* 88e6131 interrupt */
+	MPP9_GPIO,		/* GE_RXERR */
+	MPP10_GPIO,		/* PCI_intB */
+	MPP11_GPIO,		/* LED2 */
+	MPP12_GIGE,		/* GE_TXD[4] */
+	MPP13_GIGE,		/* GE_TXD[5] */
+	MPP14_GIGE,		/* GE_TXD[6] */
+	MPP15_GIGE,		/* GE_TXD[7] */
+	MPP16_GIGE,		/* GE_RXD[4] */
+	MPP17_GIGE,		/* GE_RXD[5] */
+	MPP18_GIGE,		/* GE_RXD[6] */
+	MPP19_GIGE,		/* GE_RXD[7] */
+	0,
 };
 
 static struct mv643xx_eth_platform_data rd88f5181l_ge_eth_data = {

arch/arm/mach-orion5x/rd88f5182-setup.c

@@ -241,28 +241,28 @@ static struct mv_sata_platform_data rd88f5182_sata_data = {
 /*****************************************************************************
  * General Setup
  ****************************************************************************/
-static struct orion5x_mpp_mode rd88f5182_mpp_modes[] __initdata = {
-	{  0, MPP_GPIO },		/* Debug Led */
-	{  1, MPP_GPIO },		/* Reset Switch */
-	{  2, MPP_UNUSED },
-	{  3, MPP_GPIO },		/* RTC Int */
-	{  4, MPP_GPIO },
-	{  5, MPP_GPIO },
-	{  6, MPP_GPIO },		/* PCI_intA */
-	{  7, MPP_GPIO },		/* PCI_intB */
-	{  8, MPP_UNUSED },
-	{  9, MPP_UNUSED },
-	{ 10, MPP_UNUSED },
-	{ 11, MPP_UNUSED },
-	{ 12, MPP_SATA_LED },		/* SATA 0 presence */
-	{ 13, MPP_SATA_LED },		/* SATA 1 presence */
-	{ 14, MPP_SATA_LED },		/* SATA 0 active */
-	{ 15, MPP_SATA_LED },		/* SATA 1 active */
-	{ 16, MPP_UNUSED },
-	{ 17, MPP_UNUSED },
-	{ 18, MPP_UNUSED },
-	{ 19, MPP_UNUSED },
-	{ -1 },
+static unsigned int rd88f5182_mpp_modes[] __initdata = {
+	MPP0_GPIO,		/* Debug Led */
+	MPP1_GPIO,		/* Reset Switch */
+	MPP2_UNUSED,
+	MPP3_GPIO,		/* RTC Int */
+	MPP4_GPIO,
+	MPP5_GPIO,
+	MPP6_GPIO,		/* PCI_intA */
+	MPP7_GPIO,		/* PCI_intB */
+	MPP8_UNUSED,
+	MPP9_UNUSED,
+	MPP10_UNUSED,
+	MPP11_UNUSED,
+	MPP12_SATA_LED,		/* SATA 0 presence */
+	MPP13_SATA_LED,		/* SATA 1 presence */
+	MPP14_SATA_LED,		/* SATA 0 active */
+	MPP15_SATA_LED,		/* SATA 1 active */
+	MPP16_UNUSED,
+	MPP17_UNUSED,
+	MPP18_UNUSED,
+	MPP19_UNUSED,
+	0,
 };
 
 static void __init rd88f5182_init(void)

arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c

@@ -27,7 +27,6 @@
 #include <asm/mach/pci.h>
 #include <mach/orion5x.h>
 #include "common.h"
-#include "mpp.h"
 
 static struct mv643xx_eth_platform_data rd88f6183ap_ge_eth_data = {
 	.phy_addr	= -1,

arch/arm/plat-orion/Makefile

@@ -2,7 +2,7 @@
 # Makefile for the linux kernel.
 #
 
-obj-y	:= irq.o pcie.o time.o
+obj-y	:= irq.o pcie.o time.o common.o mpp.o
 obj-m	:=
 obj-n	:=
 obj-	:=

arch/arm/plat-orion/include/plat/gpio.h

@@ -39,7 +39,6 @@ void __init orion_gpio_init(int gpio_base, int ngpio,
 /*
  * GPIO interrupt handling.
  */
-extern struct irq_chip orion_gpio_irq_chip;
 void orion_gpio_irq_handler(int irqoff);