[SCSI] qla2xxx: Add internal loopback support for ISP81xx.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

drivers/scsi/qla2xxx/qla_bsg.c

@@ -483,6 +483,98 @@ qla2x00_process_ct(struct fc_bsg_job *bsg_job)
 	return rval;
 }
 
+/* Set the port configuration to enable the
+ * internal loopback on ISP81XX
+ */
+static inline int
+qla81xx_set_internal_loopback(scsi_qla_host_t *vha, uint16_t *config,
+    uint16_t *new_config)
+{
+	int ret = 0;
+	int rval = 0;
+	struct qla_hw_data *ha = vha->hw;
+
+	if (!IS_QLA81XX(ha))
+		goto done_set_internal;
+
+	new_config[0] = config[0] | (ENABLE_INTERNAL_LOOPBACK << 1);
+	memcpy(&new_config[1], &config[1], sizeof(uint16_t) * 3) ;
+
+	ha->notify_dcbx_comp = 1;
+	ret = qla81xx_set_port_config(vha, new_config);
+	if (ret != QLA_SUCCESS) {
+		DEBUG2(printk(KERN_ERR
+		    "%s(%lu): Set port config failed\n",
+		    __func__, vha->host_no));
+		ha->notify_dcbx_comp = 0;
+		rval = -EINVAL;
+		goto done_set_internal;
+	}
+
+	/* Wait for DCBX complete event */
+	if (!wait_for_completion_timeout(&ha->dcbx_comp, (20 * HZ))) {
+		DEBUG2(qla_printk(KERN_WARNING, ha,
+		    "State change notificaition not received.\n"));
+	} else
+		DEBUG2(qla_printk(KERN_INFO, ha,
+		    "State change RECEIVED\n"));
+
+	ha->notify_dcbx_comp = 0;
+
+done_set_internal:
+	return rval;
+}
+
+/* Set the port configuration to disable the
+ * internal loopback on ISP81XX
+ */
+static inline int
+qla81xx_reset_internal_loopback(scsi_qla_host_t *vha, uint16_t *config,
+    int wait)
+{
+	int ret = 0;
+	int rval = 0;
+	uint16_t new_config[4];
+	struct qla_hw_data *ha = vha->hw;
+
+	if (!IS_QLA81XX(ha))
+		goto done_reset_internal;
+
+	memset(new_config, 0 , sizeof(new_config));
+	if ((config[0] & INTERNAL_LOOPBACK_MASK) >> 1 ==
+			ENABLE_INTERNAL_LOOPBACK) {
+		new_config[0] = config[0] & ~INTERNAL_LOOPBACK_MASK;
+		memcpy(&new_config[1], &config[1], sizeof(uint16_t) * 3) ;
+
+		ha->notify_dcbx_comp = wait;
+		ret = qla81xx_set_port_config(vha, new_config);
+		if (ret != QLA_SUCCESS) {
+			DEBUG2(printk(KERN_ERR
+			    "%s(%lu): Set port config failed\n",
+			     __func__, vha->host_no));
+			ha->notify_dcbx_comp = 0;
+			rval = -EINVAL;
+			goto done_reset_internal;
+		}
+
+		/* Wait for DCBX complete event */
+		if (wait && !wait_for_completion_timeout(&ha->dcbx_comp,
+			(20 * HZ))) {
+			DEBUG2(qla_printk(KERN_WARNING, ha,
+			    "State change notificaition not received.\n"));
+			ha->notify_dcbx_comp = 0;
+			rval = -EINVAL;
+			goto done_reset_internal;
+		} else
+			DEBUG2(qla_printk(KERN_INFO, ha,
+			    "State change RECEIVED\n"));
+
+		ha->notify_dcbx_comp = 0;
+	}
+done_reset_internal:
+	return rval;
+}
+
 static int
 qla2x00_process_loopback(struct fc_bsg_job *bsg_job)
 {
@@ -494,6 +586,7 @@ qla2x00_process_loopback(struct fc_bsg_job *bsg_job)
 	char *type;
 	struct msg_echo_lb elreq;
 	uint16_t response[MAILBOX_REGISTER_COUNT];
+	uint16_t config[4], new_config[4];
 	uint8_t *fw_sts_ptr;
 	uint8_t *req_data = NULL;
 	dma_addr_t req_data_dma;
@@ -568,7 +661,58 @@ qla2x00_process_loopback(struct fc_bsg_job *bsg_job)
 
 	elreq.options = bsg_job->request->rqst_data.h_vendor.vendor_cmd[1];
 
-	if (ha->current_topology != ISP_CFG_F) {
+	if ((ha->current_topology == ISP_CFG_F ||
+	    (IS_QLA81XX(ha) &&
+	    le32_to_cpu(*(uint32_t *)req_data) == ELS_OPCODE_BYTE
+	    && req_data_len == MAX_ELS_FRAME_PAYLOAD)) &&
+		elreq.options == EXTERNAL_LOOPBACK) {
+		type = "FC_BSG_HST_VENDOR_ECHO_DIAG";
+		DEBUG2(qla_printk(KERN_INFO, ha,
+			"scsi(%ld) bsg rqst type: %s\n", vha->host_no, type));
+		command_sent = INT_DEF_LB_ECHO_CMD;
+		rval = qla2x00_echo_test(vha, &elreq, response);
+	} else {
+		if (IS_QLA81XX(ha)) {
+			memset(config, 0, sizeof(config));
+			memset(new_config, 0, sizeof(new_config));
+			if (qla81xx_get_port_config(vha, config)) {
+				DEBUG2(printk(KERN_ERR
+					"%s(%lu): Get port config failed\n",
+					__func__, vha->host_no));
+				bsg_job->reply->reply_payload_rcv_len = 0;
+				bsg_job->reply->result = (DID_ERROR << 16);
+				rval = -EPERM;
+				goto done_free_dma_req;
+			}
+
+			if (elreq.options != EXTERNAL_LOOPBACK) {
+				DEBUG2(qla_printk(KERN_INFO, ha,
+					"Internal: current port config = %x\n",
+					config[0]));
+				if (qla81xx_set_internal_loopback(vha, config,
+					new_config)) {
+					bsg_job->reply->reply_payload_rcv_len =
+						0;
+					bsg_job->reply->result =
+						(DID_ERROR << 16);
+					rval = -EPERM;
+					goto done_free_dma_req;
+				}
+			} else {
+				/* For external loopback to work
+				 * ensure internal loopback is disabled
+				 */
+				if (qla81xx_reset_internal_loopback(vha,
+					config, 1)) {
+					bsg_job->reply->reply_payload_rcv_len =
+						0;
+					bsg_job->reply->result =
+						(DID_ERROR << 16);
+					rval = -EPERM;
+					goto done_free_dma_req;
+				}
+			}
+
 			type = "FC_BSG_HST_VENDOR_LOOPBACK";
 			DEBUG2(qla_printk(KERN_INFO, ha,
 				"scsi(%ld) bsg rqst type: %s\n",
@@ -576,21 +720,43 @@ qla2x00_process_loopback(struct fc_bsg_job *bsg_job)
 
 			command_sent = INT_DEF_LB_LOOPBACK_CMD;
 			rval = qla2x00_loopback_test(vha, &elreq, response);
-		if (IS_QLA81XX(ha)) {
+
+			if (new_config[1]) {
+				/* Revert back to original port config
+				 * Also clear internal loopback
+				 */
+				qla81xx_reset_internal_loopback(vha,
+				    new_config, 0);
+			}
+
 			if (response[0] == MBS_COMMAND_ERROR &&
 					response[1] == MBS_LB_RESET) {
 				DEBUG2(printk(KERN_ERR "%s(%ld): ABORTing "
 					"ISP\n", __func__, vha->host_no));
 				set_bit(ISP_ABORT_NEEDED, &vha->dpc_flags);
 				qla2xxx_wake_dpc(vha);
+				qla2x00_wait_for_chip_reset(vha);
+				/* Also reset the MPI */
+				if (qla81xx_restart_mpi_firmware(vha) !=
+				    QLA_SUCCESS) {
+					qla_printk(KERN_INFO, ha,
+					    "MPI reset failed for host%ld.\n",
+					    vha->host_no);
 				}
+
+				bsg_job->reply->reply_payload_rcv_len = 0;
+				bsg_job->reply->result = (DID_ERROR << 16);
+				rval = -EIO;
+				goto done_free_dma_req;
 			}
 		} else {
-		type = "FC_BSG_HST_VENDOR_ECHO_DIAG";
+			type = "FC_BSG_HST_VENDOR_LOOPBACK";
 			DEBUG2(qla_printk(KERN_INFO, ha,
-		    "scsi(%ld) bsg rqst type: %s\n", vha->host_no, type));
-		command_sent = INT_DEF_LB_ECHO_CMD;
-		rval = qla2x00_echo_test(vha, &elreq, response);
+				"scsi(%ld) bsg rqst type: %s\n",
+				vha->host_no, type));
+			command_sent = INT_DEF_LB_LOOPBACK_CMD;
+			rval = qla2x00_loopback_test(vha, &elreq, response);
+		}
 	}
 
 	if (rval) {

drivers/scsi/qla2xxx/qla_bsg.h

@@ -19,6 +19,13 @@
 #define INT_DEF_LB_LOOPBACK_CMD         0
 #define INT_DEF_LB_ECHO_CMD             1
 
+/* Loopback related definations */
+#define EXTERNAL_LOOPBACK		0xF2
+#define ENABLE_INTERNAL_LOOPBACK	0x02
+#define INTERNAL_LOOPBACK_MASK		0x000E
+#define MAX_ELS_FRAME_PAYLOAD		252
+#define ELS_OPCODE_BYTE			0x10
+
 /* BSG Vendor specific definations */
 #define A84_ISSUE_WRITE_TYPE_CMD        0
 #define A84_ISSUE_READ_TYPE_CMD         1

drivers/scsi/qla2xxx/qla_def.h

@@ -714,6 +714,8 @@ typedef struct {
 #define MBC_SEND_RNFT_ELS		0x5e	/* Send RNFT ELS request */
 #define MBC_GET_LINK_PRIV_STATS		0x6d	/* Get link & private data. */
 #define MBC_SET_VENDOR_ID		0x76	/* Set Vendor ID. */
+#define MBC_SET_PORT_CONFIG		0x122	/* Set port configuration */
+#define MBC_GET_PORT_CONFIG		0x123	/* Get port configuration */
 
 /* Firmware return data sizes */
 #define FCAL_MAP_SIZE	128
@@ -2631,6 +2633,8 @@ struct qla_hw_data {
 	struct mutex vport_lock;        /* Virtual port synchronization */
 	struct completion mbx_cmd_comp; /* Serialize mbx access */
 	struct completion mbx_intr_comp;  /* Used for completion notification */
+	struct completion dcbx_comp;	/* For set port config notification */
+	int notify_dcbx_comp;
 
 	/* Basic firmware related information. */
 	uint16_t	fw_major_version;

drivers/scsi/qla2xxx/qla_gbl.h

@@ -357,6 +357,11 @@ qla2x00_write_ram_word(scsi_qla_host_t *, uint32_t, uint32_t);
 extern int qla2x00_get_data_rate(scsi_qla_host_t *);
 extern int qla24xx_set_fcp_prio(scsi_qla_host_t *, uint16_t, uint16_t,
 	uint16_t *);
+extern int
+qla81xx_get_port_config(scsi_qla_host_t *, uint16_t *);
+
+extern int
+qla81xx_set_port_config(scsi_qla_host_t *, uint16_t *);
 
 /*
  * Global Function Prototypes in qla_isr.c source file.

drivers/scsi/qla2xxx/qla_isr.c

@@ -545,10 +545,13 @@ qla2x00_async_event(scsi_qla_host_t *vha, struct rsp_que *rsp, uint16_t *mb)
 		if (IS_QLA2100(ha))
 			break;
 
-		if (IS_QLA8XXX_TYPE(ha))
+		if (IS_QLA8XXX_TYPE(ha)) {
 			DEBUG2(printk("scsi(%ld): DCBX Completed -- %04x %04x "
 			    "%04x\n", vha->host_no, mb[1], mb[2], mb[3]));
-		else
+			if (ha->notify_dcbx_comp)
+				complete(&ha->dcbx_comp);
+
+		} else
 			DEBUG2(printk("scsi(%ld): Asynchronous P2P MODE "
 			    "received.\n", vha->host_no));
 

drivers/scsi/qla2xxx/qla_mbx.c

@@ -3949,6 +3949,72 @@ qla2x00_get_data_rate(scsi_qla_host_t *vha)
 	return rval;
 }
 
+int
+qla81xx_get_port_config(scsi_qla_host_t *vha, uint16_t *mb)
+{
+	int rval;
+	mbx_cmd_t mc;
+	mbx_cmd_t *mcp = &mc;
+	struct qla_hw_data *ha = vha->hw;
+
+	DEBUG11(printk(KERN_INFO
+	    "%s(%ld): entered.\n", __func__, vha->host_no));
+
+	if (!IS_QLA81XX(ha))
+		return QLA_FUNCTION_FAILED;
+	mcp->mb[0] = MBC_GET_PORT_CONFIG;
+	mcp->out_mb = MBX_0;
+	mcp->in_mb = MBX_4|MBX_3|MBX_2|MBX_1|MBX_0;
+	mcp->tov = MBX_TOV_SECONDS;
+	mcp->flags = 0;
+
+	rval = qla2x00_mailbox_command(vha, mcp);
+
+	if (rval != QLA_SUCCESS) {
+		DEBUG2_3_11(printk(KERN_WARNING
+		    "%s(%ld): failed=%x (%x).\n", __func__,
+		    vha->host_no, rval, mcp->mb[0]));
+	} else {
+		/* Copy all bits to preserve original value */
+		memcpy(mb, &mcp->mb[1], sizeof(uint16_t) * 4);
+
+		DEBUG11(printk(KERN_INFO
+		    "%s(%ld): done.\n", __func__, vha->host_no));
+	}
+	return rval;
+}
+
+int
+qla81xx_set_port_config(scsi_qla_host_t *vha, uint16_t *mb)
+{
+	int rval;
+	mbx_cmd_t mc;
+	mbx_cmd_t *mcp = &mc;
+
+	DEBUG11(printk(KERN_INFO
+	    "%s(%ld): entered.\n", __func__, vha->host_no));
+
+	mcp->mb[0] = MBC_SET_PORT_CONFIG;
+	/* Copy all bits to preserve original setting */
+	memcpy(&mcp->mb[1], mb, sizeof(uint16_t) * 4);
+	mcp->out_mb = MBX_4|MBX_3|MBX_2|MBX_1|MBX_0;
+	mcp->in_mb = MBX_0;
+	mcp->tov = MBX_TOV_SECONDS;
+	mcp->flags = 0;
+	rval = qla2x00_mailbox_command(vha, mcp);
+
+	if (rval != QLA_SUCCESS) {
+		DEBUG2_3_11(printk(KERN_WARNING
+		    "%s(%ld): failed=%x (%x).\n", __func__,
+		    vha->host_no, rval, mcp->mb[0]));
+	} else
+		DEBUG11(printk(KERN_INFO
+		    "%s(%ld): done.\n", __func__, vha->host_no));
+
+	return rval;
+}
+
+
 int
 qla24xx_set_fcp_prio(scsi_qla_host_t *vha, uint16_t loop_id, uint16_t priority,
 		uint16_t *mb)

drivers/scsi/qla2xxx/qla_os.c

@@ -2128,6 +2128,7 @@ qla2x00_probe_one(struct pci_dev *pdev, const struct pci_device_id *id)
 	init_completion(&ha->mbx_cmd_comp);
 	complete(&ha->mbx_cmd_comp);
 	init_completion(&ha->mbx_intr_comp);
+	init_completion(&ha->dcbx_comp);
 
 	set_bit(0, (unsigned long *) ha->vp_idx_map);