V4L/DVB (8555): au8522: add mechanism to configure IF frequency for vsb and qam

Add a mechanism to configure IF frequency for vsb and qam.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

drivers/media/dvb/frontends/au8522.c

@@ -304,6 +304,70 @@ static int au8522_mse2snr_lookup(struct mse2snr_tab *tab, int sz, int mse,
 	return ret;
 }
 
+/* 3.25 MHz IF Frequency table */
+static struct {
+	u16 reg;
+	u16 data;
+} if_3_25_mhz_tab[] = {
+	{ 0x80b5, 0x00 },
+	{ 0x80b6, 0x3d },
+	{ 0x80b7, 0xa0 },
+};
+
+/* 4.00 MHz IF Frequency table */
+static struct {
+	u16 reg;
+	u16 data;
+} if_4_mhz_tab[] = {
+	{ 0x80b5, 0x00 },
+	{ 0x80b6, 0x4b },
+	{ 0x80b7, 0xd9 },
+};
+
+/* 6.00 MHz IF Frequency table */
+static struct {
+	u16 reg;
+	u16 data;
+} if_6_mhz_tab[] = {
+	{ 0x80b5, 0xfb },
+	{ 0x80b6, 0x8e },
+	{ 0x80b7, 0x39 },
+};
+
+static int au8522_set_if(struct dvb_frontend *fe, enum au8522_if_freq if_freq)
+{
+	struct au8522_state *state = fe->demodulator_priv;
+	int i;
+
+	switch (if_freq) {
+	case AU8522_IF_3_25MHZ:
+		dprintk("%s() 3.25 MHz\n", __func__);
+		for (i = 0; i < ARRAY_SIZE(if_3_25_mhz_tab); i++)
+			au8522_writereg(state,
+					if_3_25_mhz_tab[i].reg,
+					if_3_25_mhz_tab[i].data);
+		break;
+	case AU8522_IF_4MHZ:
+		dprintk("%s() 4.00 MHz\n", __func__);
+		for (i = 0; i < ARRAY_SIZE(if_4_mhz_tab); i++)
+			au8522_writereg(state,
+					if_4_mhz_tab[i].reg,
+					if_4_mhz_tab[i].data);
+		break;
+	case AU8522_IF_6MHZ:
+		dprintk("%s() 6.00 MHz\n", __func__);
+		for (i = 0; i < ARRAY_SIZE(if_6_mhz_tab); i++)
+			au8522_writereg(state,
+					if_6_mhz_tab[i].reg,
+					if_6_mhz_tab[i].data);
+		break;
+	default:
+		dprintk("%s() IF Frequency not supported\n", __func__);
+		return -EINVAL;
+	}
+	return 0;
+}
+
 /* VSB Modulation table */
 static struct {
 	u16 reg;
@@ -438,6 +502,7 @@ static int au8522_enable_modulation(struct dvb_frontend *fe,
 			au8522_writereg(state,
 				VSB_mod_tab[i].reg,
 				VSB_mod_tab[i].data);
+		au8522_set_if(fe, state->config->vsb_if);
 		break;
 	case QAM_64:
 	case QAM_256:
@@ -446,6 +511,7 @@ static int au8522_enable_modulation(struct dvb_frontend *fe,
 			au8522_writereg(state,
 				QAM_mod_tab[i].reg,
 				QAM_mod_tab[i].data);
+		au8522_set_if(fe, state->config->qam_if);
 		break;
 	default:
 		dprintk("%s() Invalid modulation\n", __func__);

drivers/media/dvb/frontends/au8522.h

@@ -24,6 +24,12 @@
 
 #include <linux/dvb/frontend.h>
 
+enum au8522_if_freq {
+	AU8522_IF_6MHZ = 0,
+	AU8522_IF_4MHZ,
+	AU8522_IF_3_25MHZ,
+};
+
 struct au8522_config {
 	/* the demodulator's i2c address */
 	u8 demod_address;
@@ -32,6 +38,9 @@ struct au8522_config {
 #define AU8522_TUNERLOCKING 0
 #define AU8522_DEMODLOCKING 1
 	u8 status_mode;
+
+	enum au8522_if_freq vsb_if;
+	enum au8522_if_freq qam_if;
 };
 
 #if defined(CONFIG_DVB_AU8522) || 				\