dt/bindings: remove device_type "network" references

device_type is deprecated and the kernel doesn't require it in most
cases. The only exceptions for flat tree users are the "gianfar",
"ucc_geth" and "ibm,emac" bindings, and arguably that requirement could
be relaxed for ucc_geth and ibm,emac (that is a task for separate
patches though).

This patch removes references to device_type="network" from the binding
documentation where possible and removes the properties from ARM and
microblaze dts files. This patch does not modify the powerpc .dts files
since there are a much larger number of them affected and I think the
ucc_geth, ibm,emac and gianfar users should be addressed before clearing
out the references to reduce the chance of breakage.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Michal Simek <monstr@monstr.eu>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>

Documentation/devicetree/bindings/marvell.txt

@@ -130,7 +130,6 @@ prefixed with the string "marvell,", for Marvell Technology Group Ltd.
    Ethernet port node
 
    Required properties:
-     - device_type : Should be "network".
      - compatible : Should be "marvell,mv64360-eth".
      - reg : Should be <0>, <1>, or <2>, according to which registers
        within the silicon block the device uses.
@@ -143,7 +142,6 @@ prefixed with the string "marvell,", for Marvell Technology Group Ltd.
 
    Example Discovery Ethernet port node:
      ethernet@0 {
-	     device_type = "network";
 	     compatible = "marvell,mv64360-eth";
 	     reg = <0>;
 	     interrupts = <32>;

Documentation/devicetree/bindings/net/marvell-orion-net.txt

@@ -32,7 +32,6 @@ Optional controller properties:
 * Ethernet port node
 
 Required port properties:
- - device_type: shall be "network".
  - compatible: shall be one of "marvell,orion-eth-port",
       "marvell,kirkwood-eth-port".
  - reg: port number relative to ethernet controller, shall be 0, 1, or 2.
@@ -74,7 +73,6 @@ eth: ethernet-controller@72000 {
 	marvell,tx-checksum-limit = <1600>;
 
 	ethernet@0 {
-		device_type = "network";
 		compatible = "marvell,orion-eth-port";
 		reg = <0>;
 		interrupts = <29>;

Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/network.txt

@@ -10,7 +10,6 @@ Currently defined compatibles:
 Example:
 
 	ethernet@11300 {
-		device_type = "network";
 		compatible = "fsl,mpc8272-fcc-enet",
 			     "fsl,cpm2-fcc-enet";
 		reg = <11300 20 8400 100 11390 1>;

arch/arm/boot/dts/dove.dtsi

@@ -573,7 +573,6 @@ eth: ethernet-ctrl@72000 {
 				status = "disabled";
 
 				ethernet-port@0 {
-					device_type = "network";
 					compatible = "marvell,orion-eth-port";
 					reg = <0>;
 					interrupts = <29>;

arch/arm/boot/dts/kirkwood.dtsi

@@ -253,7 +253,6 @@ eth0: ethernet-controller@72000 {
 			status = "disabled";
 
 			ethernet0-port@0 {
-				device_type = "network";
 				compatible = "marvell,kirkwood-eth-port";
 				reg = <0>;
 				interrupts = <11>;
@@ -273,7 +272,6 @@ eth1: ethernet-controller@76000 {
 			status = "disabled";
 
 			ethernet1-port@0 {
-				device_type = "network";
 				compatible = "marvell,kirkwood-eth-port";
 				reg = <0>;
 				interrupts = <15>;

arch/arm/boot/dts/orion5x.dtsi

@@ -154,7 +154,6 @@ eth: ethernet-controller@72000 {
 			status = "disabled";
 
 			ethernet-port@0 {
-				device_type = "network";
 				compatible = "marvell,orion-eth-port";
 				reg = <0>;
 				/* overwrite MAC address in bootloader */

arch/microblaze/platform/generic/system.dts

@@ -222,7 +222,6 @@ Hard_Ethernet_MAC: xps-ll-temac@81c00000 {
 			ranges ;
 			ethernet@81c00000 {
 				compatible = "xlnx,xps-ll-temac-1.01.b", "xlnx,xps-ll-temac-1.00.a";
-				device_type = "network";
 				interrupt-parent = <&xps_intc_0>;
 				interrupts = < 5 2 >;
 				llink-connected = <&PIM3>;