arm64: dts: qcom: msm8916-huawei-g7: Add sound card

The huawei-g7 uses the msm8916-wcd-digital/analog audio codecs similar
to apq8016-sbc, so we can mostly copy paste it from there to make audio
work correctly. The main difference is the hphl-jack-type-normally-open
property, which is needed to avoid inverted audio jack detection.

Note that at least on my device the jack detection is not fully
reliable: sometimes headphones are detected as headsets (with
microphone). However, this is not a big problem for typical usage.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220410195113.13646-3-stephan@gerhold.net

arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts

@@ -8,6 +8,7 @@
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/leds/common.h>
+#include <dt-bindings/sound/apq8016-lpass.h>
 
 /*
  * Note: The original firmware from Huawei can only boot 32-bit kernels.
@@ -211,6 +212,10 @@ &blsp1_uart2 {
 	status = "okay";
 };
 
+&lpass {
+	status = "okay";
+};
+
 &pm8916_resin {
 	status = "okay";
 	linux,code = <KEY_VOLUMEDOWN>;
@@ -255,6 +260,40 @@ &sdhc_2 {
 	cd-gpios = <&msmgpio 56 GPIO_ACTIVE_LOW>;
 };
 
+&sound {
+	status = "okay";
+
+	model = "msm8916";
+	audio-routing =
+		"AMIC1", "MIC BIAS External1",
+		"AMIC2", "MIC BIAS External2",
+		"AMIC3", "MIC BIAS External1";
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&cdc_pdm_lines_act>;
+	pinctrl-1 = <&cdc_pdm_lines_sus>;
+
+	primary-dai-link {
+		link-name = "WCD";
+		cpu {
+			sound-dai = <&lpass MI2S_PRIMARY>;
+		};
+		codec {
+			sound-dai = <&lpass_codec 0>, <&wcd_codec 0>;
+		};
+	};
+
+	tertiary-dai-link {
+		link-name = "WCD-Capture";
+		cpu {
+			sound-dai = <&lpass MI2S_TERTIARY>;
+		};
+		codec {
+			sound-dai = <&lpass_codec 1>, <&wcd_codec 1>;
+		};
+	};
+};
+
 &usb {
 	status = "okay";
 	extcon = <&usb_id>, <&usb_id>;
@@ -264,6 +303,13 @@ &usb_hs_phy {
 	extcon = <&usb_id>;
 };
 
+&wcd_codec {
+	qcom,micbias-lvl = <2800>;
+	qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
+	qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
+	qcom,hphl-jack-type-normally-open;
+};
+
 &smd_rpm_regulators {
 	vdd_l1_l2_l3-supply = <&pm8916_s3>;
 	vdd_l4_l5_l6-supply = <&pm8916_s4>;