drm/meson: Add G12A support for the DW-HDMI Glue

The Amlogic G12A embeds the same Synopsys DW-HDMI Controller,
but with :
- a "backport" of the HDR signaling registers from more recent
  DW-HDMI controllers, this will need a tweak since it's not
  normally present on this version of the DW-HDMI controller
- A direct mapping of TOP and DW-HDMI registers instead of an
  internal bus accessed using read/write registers
- Support for RX-SENSE, but not yet implemented
- Support for HDMI 2.1 Dynamic HDR, but not yet implemented
- Different registers mapping for the HDMI PHY setup

This patchs adds support for these changes while providing exact
same support as the previous GXBB, GXL & GXM SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-12-narmstrong@baylibre.com

drivers/gpu/drm/meson/meson_dw_hdmi.h

@@ -21,9 +21,12 @@
 #define __MESON_DW_HDMI_H
 
 /*
- * Bit 7 RW Reserved. Default 1.
- * Bit 6 RW Reserved. Default 1.
- * Bit 5 RW Reserved. Default 1.
+ * Bit 15-10: RW Reserved. Default 1 starting from G12A
+ * Bit 9 RW sw_reset_i2c starting from G12A
+ * Bit 8 RW sw_reset_axiarb starting from G12A
+ * Bit 7 RW Reserved. Default 1, sw_reset_emp starting from G12A
+ * Bit 6 RW Reserved. Default 1, sw_reset_flt starting from G12A
+ * Bit 5 RW Reserved. Default 1, sw_reset_hdcp22 starting from G12A
  * Bit 4 RW sw_reset_phyif: PHY interface. 1=Apply reset; 0=Release from reset.
  *     Default 1.
  * Bit 3 RW sw_reset_intr: interrupt module. 1=Apply reset;
@@ -39,12 +42,16 @@
 #define HDMITX_TOP_SW_RESET                     (0x000)
 
 /*
+ * Bit 31 RW free_clk_en: 0=Enable clock gating for power saving; 1= Disable
  * Bit 12 RW i2s_ws_inv:1=Invert i2s_ws; 0=No invert. Default 0.
  * Bit 11 RW i2s_clk_inv: 1=Invert i2s_clk; 0=No invert. Default 0.
  * Bit 10 RW spdif_clk_inv: 1=Invert spdif_clk; 0=No invert. Default 0.
  * Bit 9 RW tmds_clk_inv: 1=Invert tmds_clk; 0=No invert. Default 0.
  * Bit 8 RW pixel_clk_inv: 1=Invert pixel_clk; 0=No invert. Default 0.
- * Bit 4 RW cec_clk_en: 1=enable cec_clk; 0=disable. Default 0.
+ * Bit 7 RW hdcp22_skpclk_en: starting from G12A, 1=enable; 0=disable
+ * Bit 6 RW hdcp22_esmclk_en: starting from G12A, 1=enable; 0=disable
+ * Bit 5 RW hdcp22_tmdsclk_en: starting from G12A, 1=enable; 0=disable
+ * Bit 4 RW cec_clk_en: 1=enable cec_clk; 0=disable. Default 0. Reserved for G12A
  * Bit 3 RW i2s_clk_en: 1=enable i2s_clk; 0=disable. Default 0.
  * Bit 2 RW spdif_clk_en: 1=enable spdif_clk; 0=disable. Default 0.
  * Bit 1 RW tmds_clk_en: 1=enable tmds_clk;  0=disable. Default 0.
@@ -53,6 +60,8 @@
 #define HDMITX_TOP_CLK_CNTL                     (0x001)
 
 /*
+ * Bit 31:28 RW rxsense_glitch_width: starting from G12A
+ * Bit 27:16 RW rxsense_valid_width: starting from G12A
  * Bit 11: 0 RW hpd_valid_width: filter out width <= M*1024.    Default 0.
  * Bit 15:12 RW hpd_glitch_width: filter out glitch <= N.       Default 0.
  */
@@ -61,6 +70,9 @@
 /*
  * intr_maskn: MASK_N, one bit per interrupt source.
  *     1=Enable interrupt source; 0=Disable interrupt source. Default 0.
+ * [  7] rxsense_fall starting from G12A
+ * [  6] rxsense_rise starting from G12A
+ * [  5] err_i2c_timeout starting from G12A
  * [  4] hdcp22_rndnum_err
  * [  3] nonce_rfrsh_rise
  * [  2] hpd_fall_intr
@@ -73,6 +85,9 @@
  * Bit 30: 0 RW intr_stat: For each bit, write 1 to manually set the interrupt
  *     bit, read back the interrupt status.
  * Bit    31 R  IP interrupt status
+ * Bit     7 RW rxsense_fall starting from G12A
+ * Bit     6 RW rxsense_rise starting from G12A
+ * Bit     5 RW err_i2c_timeout starting from G12A
  * Bit     2 RW hpd_fall
  * Bit     1 RW hpd_rise
  * Bit     0 RW IP interrupt
@@ -80,6 +95,9 @@
 #define HDMITX_TOP_INTR_STAT                    (0x004)
 
 /*
+ * [7]    rxsense_fall starting from G12A
+ * [6]    rxsense_rise starting from G12A
+ * [5]    err_i2c_timeout starting from G12A
  * [4]	  hdcp22_rndnum_err
  * [3]	  nonce_rfrsh_rise
  * [2]	  hpd_fall
@@ -91,6 +109,8 @@
 #define HDMITX_TOP_INTR_CORE		BIT(0)
 #define HDMITX_TOP_INTR_HPD_RISE	BIT(1)
 #define HDMITX_TOP_INTR_HPD_FALL	BIT(2)
+#define HDMITX_TOP_INTR_RXSENSE_RISE	BIT(6)
+#define HDMITX_TOP_INTR_RXSENSE_FALL	BIT(7)
 
 /* Bit 14:12 RW tmds_sel: 3'b000=Output zero; 3'b001=Output normal TMDS data;
  *     3'b010=Output PRBS data; 3'b100=Output shift pattern. Default 0.
@@ -140,7 +160,9 @@
  */
 #define HDMITX_TOP_REVOCMEM_STAT                (0x00D)
 
-/* Bit     0 R  filtered HPD status. */
+/* Bit	   1 R	filtered RxSense status
+ * Bit     0 R  filtered HPD status.
+ */
 #define HDMITX_TOP_STAT0                        (0x00E)
 
 #endif /* __MESON_DW_HDMI_H */