arch: arm64: dts: Add support for AM69 Starter Kit

AM69 Starter Kit is a single board designed for TI AM69 SOC that
provides advanced system integration in automotive ADAS applications,
autonomous mobile robot and edge AI applications. The SOC comprises
of Cortex-A72s in dual clusters, lockstep capable dual Cortex-R5F MCUs,
Vision Processing Accelerators (VPAC) with Image Signal Processor (ISP)
and multiple vision assist accelerators, Depth and Motion Processing
Accelerators (DMPAC), Deep-learning Matrix Multiply Accelerator(MMA)
and C7x floating point vector DSP

AM69 SK supports the following interfaces:
       * 32 GB LPDDR4 RAM
       * x1 Gigabit Ethernet interface
       * x3 USB 3.0 Type-A ports
       * x1 USB 3.0 Type-C port
       * x1 UHS-1 capable micro-SD card slot
       * x4 MCAN instances
       * 32 GB eMMC Flash
       * 512 Mbit OSPI flash
       * x2 Display connectors
       * x1 PCIe M.2 M Key
       * x1 PCIe M.2 E Key
       * x1 4L PCIe Card Slot
       * x3 CSI2 Camera interface
       * 40-pin Raspberry Pi header

Add initial support for the AM69 SK board.

Design Files: https://www.ti.com/lit/zip/SPRR466
TRM: https://www.ti.com/lit/zip/spruj52Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20230119132958.124435-3-sabiya.d@ti.com

arch/arm64/boot/dts/ti/Makefile

@@ -25,6 +25,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-j7200-common-proc-board.dtb
 
 dtb-$(CONFIG_ARCH_K3) += k3-j721s2-common-proc-board.dtb
 
+dtb-$(CONFIG_ARCH_K3) += k3-am69-sk.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm.dtb
 
 dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb

arch/arm64/boot/dts/ti/k3-am69-sk.dts

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022-2023 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ * Design Files: https://www.ti.com/lit/zip/SPRR466
+ * TRM: https://www.ti.com/lit/zip/spruj52
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "k3-j784s4.dtsi"
+
+/ {
+	compatible = "ti,am69-sk", "ti,j784s4";
+	model = "Texas Instruments AM69 SK";
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+	};
+
+	aliases {
+		serial2 = &main_uart8;
+		mmc1 = &main_sdhci1;
+		i2c0 = &main_i2c0;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		/* 32G RAM */
+		reg = <0x00 0x80000000 0x00 0x80000000>,
+		      <0x08 0x80000000 0x07 0x80000000>;
+	};
+
+	reserved_memory: reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		secure_ddr: optee@9e800000 {
+			reg = <0x00 0x9e800000 0x00 0x01800000>;
+			no-map;
+		};
+	};
+
+	vusb_main: regulator-vusb-main5v0 {
+		/* USB MAIN INPUT 5V DC */
+		compatible = "regulator-fixed";
+		regulator-name = "vusb-main5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vsys_5v0: regulator-vsys5v0 {
+		/* Output of LM61460 */
+		compatible = "regulator-fixed";
+		regulator-name = "vsys_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vusb_main>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vsys_3v3: regulator-vsys3v3 {
+		/* Output of LM5143 */
+		compatible = "regulator-fixed";
+		regulator-name = "vsys_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vusb_main>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_mmc1: regulator-sd {
+		/* Output of TPS22918 */
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_mmc1";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		enable-active-high;
+		vin-supply = <&vsys_3v3>;
+		gpio = <&exp1 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	vdd_sd_dv: regulator-tlv71033 {
+		/* Output of TLV71033 */
+		compatible = "regulator-gpio";
+		regulator-name = "tlv71033";
+		pinctrl-names = "default";
+		pinctrl-0 = <&vdd_sd_dv_pins_default>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		vin-supply = <&vsys_5v0>;
+		gpios = <&main_gpio0 49 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0x0>,
+			 <3300000 0x1>;
+	};
+};
+
+&main_pmx0 {
+	main_uart8_pins_default: main-uart8-pins-default {
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x0d0, PIN_INPUT, 11) /* (AP38) SPI0_CS1.UART8_RXD */
+			J784S4_IOPAD(0x0d4, PIN_OUTPUT, 11) /* (AN38) SPI0_CLK.UART8_TXD */
+		>;
+	};
+
+	main_i2c0_pins_default: main-i2c0-pins-default {
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x0e0, PIN_INPUT_PULLUP, 0) /* (AN36) I2C0_SCL */
+			J784S4_IOPAD(0x0e4, PIN_INPUT_PULLUP, 0) /* (AP37) I2C0_SDA */
+		>;
+	};
+
+	main_mmc1_pins_default: main-mmc1-pins-default {
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x104, PIN_INPUT, 0) /* (AB38) MMC1_CLK */
+			J784S4_IOPAD(0x108, PIN_INPUT, 0) /* (AB36) MMC1_CMD */
+			J784S4_IOPAD(0x100, PIN_INPUT, 0) /* (No Pin) MMC1_CLKLB */
+			J784S4_IOPAD(0x0fc, PIN_INPUT, 0) /* (AA33) MMC1_DAT0 */
+			J784S4_IOPAD(0x0f8, PIN_INPUT, 0) /* (AB34) MMC1_DAT1 */
+			J784S4_IOPAD(0x0f4, PIN_INPUT, 0) /* (AA32) MMC1_DAT2 */
+			J784S4_IOPAD(0x0f0, PIN_INPUT, 0) /* (AC38) MMC1_DAT3 */
+			J784S4_IOPAD(0x0e8, PIN_INPUT, 8) /* (AR38) TIMER_IO0.MMC1_SDCD */
+		>;
+	};
+
+	vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x0C4, PIN_INPUT, 7) /* (AD36) ECAP0_IN_APWM_OUT.GPIO0_49 */
+		>;
+	};
+};
+
+&main_uart8 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_uart8_pins_default>;
+};
+
+&main_i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c0_pins_default>;
+	clock-frequency = <400000>;
+
+	exp1: gpio@21 {
+		compatible = "ti,tca6416";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names	= "BOARDID_EEPROM_WP", "CAN_STB", "GPIO_uSD_PWR_EN",
+				"IO_EXP_MCU_RGMII_RST#", "IO_EXP_PCIe0_4L_PERST#",
+				"IO_EXP_PCIe1_M.2_RTSz", "IO_EXP_PCIe3_M.2_RTSz",
+				"PM_INA_BUS_EN", "ENET1_EXP_PWRDN", "EXP1_ENET_RSTz",
+				"ENET1_I2CMUX_SEL", "PCIe0_CLKREQ#", "PCIe1_M.2_CLKREQ#",
+				"PCIe3_M2_CLKREQ#", "PCIe0_PRSNT2#_1", "PCIe0_PRSNT2#_2";
+	};
+};
+
+&main_sdhci1 {
+	/* SD card */
+	status = "okay";
+	pinctrl-0 = <&main_mmc1_pins_default>;
+	pinctrl-names = "default";
+	disable-wp;
+	vmmc-supply = <&vdd_mmc1>;
+	vqmmc-supply = <&vdd_sd_dv>;
+};
+
+&main_gpio0 {
+	status = "okay";
+};