Merge tag 'soc-late-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull more ARM SoC updates from Arnd Bergmann:
 "These are changes that for some reason ended up not making it into the
  first four branches but that should still make it into 6.9:

   - A rework of the omap clock support that touches both drivers and
     device tree files

   - The reset controller branch changes that had a dependency on late
     bugfixes. Merging them here avoids a backmerge of 6.8-rc5 into the
     drivers branch

   - The RISC-V/starfive, RISC-V/microchip and ARM/Broadcom devicetree
     changes that got delayed and needed some extra time in linux-next
     for wider testing"

* tag 'soc-late-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (31 commits)
  soc: fsl: dpio: fix kcalloc() argument order
  bus: ts-nbus: Improve error reporting
  bus: ts-nbus: Convert to atomic pwm API
  riscv: dts: starfive: jh7110: Add camera subsystem nodes
  ARM: bcm: stop selecing CONFIG_TICK_ONESHOT
  ARM: dts: omap3: Update clksel clocks to use reg instead of ti,bit-shift
  ARM: dts: am3: Update clksel clocks to use reg instead of ti,bit-shift
  clk: ti: Improve clksel clock bit parsing for reg property
  clk: ti: Handle possible address in the node name
  dt-bindings: pwm: opencores: Add compatible for StarFive JH8100
  dt-bindings: riscv: cpus: reg matches hart ID
  reset: Instantiate reset GPIO controller for shared reset-gpios
  reset: gpio: Add GPIO-based reset controller
  cpufreq: do not open-code of_phandle_args_equal()
  of: Add of_phandle_args_equal() helper
  reset: simple: add support for Sophgo SG2042
  dt-bindings: reset: sophgo: support SG2042
  riscv: dts: microchip: add specific compatible for mpfs pdma
  riscv: dts: microchip: add missing CAN bus clocks
  ARM: brcmstb: Add debug UART entry for 74165
  ...

Documentation/devicetree/bindings/bus/brcm,gisb-arb.yaml

@@ -18,6 +18,7 @@ properties:
           - const: brcm,gisb-arb
       - items:
           - enum:
+              - brcm,bcm74165-gisb-arb  # for V7 new style 16nm chips
               - brcm,bcm7278-gisb-arb  # for V7 28nm chips
               - brcm,bcm7435-gisb-arb  # for newer 40nm chips
               - brcm,bcm7400-gisb-arb  # for older 40nm chips and all 65nm chips

Documentation/devicetree/bindings/pwm/opencores,pwm.yaml

+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pwm/opencores,pwm.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: OpenCores PWM controller
+
+maintainers:
+  - William Qiu <william.qiu@starfivetech.com>
+
+description:
+  The OpenCores PTC ip core contains a PWM controller. When operating in PWM
+  mode, the PTC core generates binary signal with user-programmable low and
+  high periods. All PTC counters and registers are 32-bit.
+
+allOf:
+  - $ref: pwm.yaml#
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - starfive,jh7100-pwm
+          - starfive,jh7110-pwm
+          - starfive,jh8100-pwm
+      - const: opencores,pwm-v1
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  resets:
+    maxItems: 1
+
+  "#pwm-cells":
+    const: 3
+
+required:
+  - compatible
+  - reg
+  - clocks
+
+additionalProperties: false
+
+examples:
+  - |
+    pwm@12490000 {
+        compatible = "starfive,jh7110-pwm", "opencores,pwm-v1";
+        reg = <0x12490000 0x10000>;
+        clocks = <&clkgen 181>;
+        resets = <&rstgen 109>;
+        #pwm-cells = <3>;
+    };

Documentation/devicetree/bindings/reset/sophgo,sg2042-reset.yaml

+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/reset/sophgo,sg2042-reset.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Sophgo SG2042 SoC Reset Controller
+
+maintainers:
+  - Chen Wang <unicorn_wang@outlook.com>
+
+properties:
+  compatible:
+    const: sophgo,sg2042-reset
+
+  reg:
+    maxItems: 1
+
+  "#reset-cells":
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - "#reset-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    rstgen: reset-controller@c00 {
+        compatible = "sophgo,sg2042-reset";
+        reg = <0xc00 0xc>;
+        #reset-cells = <1>;
+    };

Documentation/devicetree/bindings/riscv/cpus.yaml

@@ -75,6 +75,10 @@ properties:
       - riscv,sv57
       - riscv,none
 
+  reg:
+    description:
+      The hart ID of this CPU node.
+
   riscv,cbom-block-size:
     $ref: /schemas/types.yaml#/definitions/uint32
     description:

MAINTAINERS

@@ -8987,6 +8987,11 @@ F:	Documentation/i2c/muxes/i2c-mux-gpio.rst
 F:	drivers/i2c/muxes/i2c-mux-gpio.c
 F:	include/linux/platform_data/i2c-mux-gpio.h
 
+GENERIC GPIO RESET DRIVER
+M:	Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
+S:	Maintained
+F:	drivers/reset/reset-gpio.c
+
 GENERIC HDLC (WAN) DRIVERS
 M:	Krzysztof Halasa <khc@pm.waw.pl>
 S:	Maintained

arch/arm/boot/dts/ti/omap/am33xx-clocks.dtsi

@@ -108,30 +108,31 @@ clock@664 {
 		compatible = "ti,clksel";
 		reg = <0x664>;
 		#clock-cells = <2>;
-		#address-cells = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		ehrpwm0_tbclk: clock-ehrpwm0-tbclk {
+		ehrpwm0_tbclk: clock-ehrpwm0-tbclk@0 {
+			reg = <0>;
 			#clock-cells = <0>;
 			compatible = "ti,gate-clock";
 			clock-output-names = "ehrpwm0_tbclk";
 			clocks = <&l4ls_gclk>;
-			ti,bit-shift = <0>;
 		};
 
-		ehrpwm1_tbclk: clock-ehrpwm1-tbclk {
+		ehrpwm1_tbclk: clock-ehrpwm1-tbclk@1 {
+			reg = <1>;
 			#clock-cells = <0>;
 			compatible = "ti,gate-clock";
 			clock-output-names = "ehrpwm1_tbclk";
 			clocks = <&l4ls_gclk>;
-			ti,bit-shift = <1>;
 		};
 
-		ehrpwm2_tbclk: clock-ehrpwm2-tbclk {
+		ehrpwm2_tbclk: clock-ehrpwm2-tbclk@2 {
+			reg = <2>;
 			#clock-cells = <0>;
 			compatible = "ti,gate-clock";
 			clock-output-names = "ehrpwm2_tbclk";
 			clocks = <&l4ls_gclk>;
-			ti,bit-shift = <2>;
 		};
 	};
 };
@@ -566,17 +567,19 @@ clock@52c {
 		compatible = "ti,clksel";
 		reg = <0x52c>;
 		#clock-cells = <2>;
-		#address-cells = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		gfx_fclk_clksel_ck: clock-gfx-fclk-clksel {
+		gfx_fclk_clksel_ck: clock-gfx-fclk-clksel@1 {
+			reg = <1>;
 			#clock-cells = <0>;
 			compatible = "ti,mux-clock";
 			clock-output-names = "gfx_fclk_clksel_ck";
 			clocks = <&dpll_core_m4_ck>, <&dpll_per_m2_ck>;
-			ti,bit-shift = <1>;
 		};
 
-		gfx_fck_div_ck: clock-gfx-fck-div {
+		gfx_fck_div_ck: clock-gfx-fck-div@0 {
+			reg = <0>;
 			#clock-cells = <0>;
 			compatible = "ti,divider-clock";
 			clock-output-names = "gfx_fck_div_ck";
@@ -589,30 +592,32 @@ clock@700 {
 		compatible = "ti,clksel";
 		reg = <0x700>;
 		#clock-cells = <2>;
-		#address-cells = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		sysclkout_pre_ck: clock-sysclkout-pre {
+		sysclkout_pre_ck: clock-sysclkout-pre@0 {
+			reg = <0>;
 			#clock-cells = <0>;
 			compatible = "ti,mux-clock";
 			clock-output-names = "sysclkout_pre_ck";
 			clocks = <&clk_32768_ck>, <&l3_gclk>, <&dpll_ddr_m2_ck>, <&dpll_per_m2_ck>, <&lcd_gclk>;
 		};
 
-		clkout2_div_ck: clock-clkout2-div {
+		clkout2_div_ck: clock-clkout2-div@3 {
+			reg = <3>;
 			#clock-cells = <0>;
 			compatible = "ti,divider-clock";
 			clock-output-names = "clkout2_div_ck";
 			clocks = <&sysclkout_pre_ck>;
-			ti,bit-shift = <3>;
 			ti,max-div = <8>;
 		};
 
-		clkout2_ck: clock-clkout2 {
+		clkout2_ck: clock-clkout2@7 {
+			reg = <7>;
 			#clock-cells = <0>;
 			compatible = "ti,gate-clock";
 			clock-output-names = "clkout2_ck";
 			clocks = <&clkout2_div_ck>;
-			ti,bit-shift = <7>;
 		};
 	};
 };

arch/arm/boot/dts/ti/omap/am35xx-clocks.dtsi

@@ -66,22 +66,23 @@ clock@a10 {
 		compatible = "ti,clksel";
 		reg = <0xa10>;
 		#clock-cells = <2>;
-		#address-cells = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		ipss_ick: clock-ipss-ick {
+		ipss_ick: clock-ipss-ick@4 {
+			reg = <4>;
 			#clock-cells = <0>;
 			compatible = "ti,am35xx-interface-clock";
 			clock-output-names = "ipss_ick";
 			clocks = <&core_l3_ick>;
-			ti,bit-shift = <4>;
 		};
 
-		uart4_ick_am35xx: clock-uart4-ick-am35xx {
+		uart4_ick_am35xx: clock-uart4-ick-am35xx@23 {
+			reg = <23>;
 			#clock-cells = <0>;
 			compatible = "ti,omap3-interface-clock";
 			clock-output-names = "uart4_ick_am35xx";
 			clocks = <&core_l4_ick>;
-			ti,bit-shift = <23>;
 		};
 	};
 
@@ -101,14 +102,15 @@ clock@a00 {
 		compatible = "ti,clksel";
 		reg = <0xa00>;
 		#clock-cells = <2>;
-		#address-cells = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		uart4_fck_am35xx: clock-uart4-fck-am35xx {
+		uart4_fck_am35xx: clock-uart4-fck-am35xx@23 {
+			reg = <23>;
 			#clock-cells = <0>;
 			compatible = "ti,wait-gate-clock";
 			clock-output-names = "uart4_fck_am35xx";
 			clocks = <&core_48m_fck>;
-			ti,bit-shift = <23>;
 		};
 	};
 };

arch/arm/boot/dts/ti/omap/omap3430es1-clocks.dtsi

@@ -50,30 +50,31 @@ clock@a00 {
 		compatible = "ti,clksel";
 		reg = <0xa00>;
 		#clock-cells = <2>;
-		#address-cells = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		d2d_26m_fck: clock-d2d-26m-fck {
+		d2d_26m_fck: clock-d2d-26m-fck@3 {
+			reg = <3>;
 			#clock-cells = <0>;
 			compatible = "ti,wait-gate-clock";
 			clock-output-names = "d2d_26m_fck";
 			clocks = <&sys_ck>;
-			ti,bit-shift = <3>;
 		};
 
-		fshostusb_fck: clock-fshostusb-fck {
+		fshostusb_fck: clock-fshostusb-fck@5 {
+			reg = <5>;
 			#clock-cells = <0>;
 			compatible = "ti,wait-gate-clock";
 			clock-output-names = "fshostusb_fck";
 			clocks = <&core_48m_fck>;
-			ti,bit-shift = <5>;
 		};
 
-		ssi_ssr_gate_fck_3430es1: clock-ssi-ssr-gate-fck-3430es1 {
+		ssi_ssr_gate_fck_3430es1: clock-ssi-ssr-gate-fck-3430es1@0 {
+			reg = <0>;
 			#clock-cells = <0>;
 			compatible = "ti,composite-no-wait-gate-clock";
 			clock-output-names = "ssi_ssr_gate_fck_3430es1";
 			clocks = <&corex2_fck>;
-			ti,bit-shift = <0>;
 		};
 	};
 
@@ -81,23 +82,24 @@ clock@a40 {
 		compatible = "ti,clksel";
 		reg = <0xa40>;
 		#clock-cells = <2>;
-		#address-cells = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		ssi_ssr_div_fck_3430es1: clock-ssi-ssr-div-fck-3430es1 {
+		ssi_ssr_div_fck_3430es1: clock-ssi-ssr-div-fck-3430es1@8 {
+			reg = <8>;
 			#clock-cells = <0>;
 			compatible = "ti,composite-divider-clock";
 			clock-output-names = "ssi_ssr_div_fck_3430es1";
 			clocks = <&corex2_fck>;
-			ti,bit-shift = <8>;
 			ti,dividers = <0>, <1>, <2>, <3>, <4>, <0>, <6>, <0>, <8>;
 		};
 
-		usb_l4_div_ick: clock-usb-l4-div-ick {
+		usb_l4_div_ick: clock-usb-l4-div-ick@4 {
+			reg = <4>;
 			#clock-cells = <0>;
 			compatible = "ti,composite-divider-clock";
 			clock-output-names = "usb_l4_div_ick";
 			clocks = <&l4_ick>;
-			ti,bit-shift = <4>;
 			ti,max-div = <1>;
 			ti,index-starts-at-one;
 		};
@@ -121,38 +123,39 @@ clock@a10 {
 		compatible = "ti,clksel";
 		reg = <0xa10>;
 		#clock-cells = <2>;
-		#address-cells = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		hsotgusb_ick_3430es1: clock-hsotgusb-ick-3430es1 {
+		hsotgusb_ick_3430es1: clock-hsotgusb-ick-3430es1@4 {
+			reg = <4>;
 			#clock-cells = <0>;
 			compatible = "ti,omap3-no-wait-interface-clock";
 			clock-output-names = "hsotgusb_ick_3430es1";
 			clocks = <&core_l3_ick>;
-			ti,bit-shift = <4>;
 		};
 
-		fac_ick: clock-fac-ick {
+		fac_ick: clock-fac-ick@8 {
+			reg = <8>;
 			#clock-cells = <0>;
 			compatible = "ti,omap3-interface-clock";
 			clock-output-names = "fac_ick";
 			clocks = <&core_l4_ick>;
-			ti,bit-shift = <8>;
 		};
 
-		ssi_ick: clock-ssi-ick-3430es1 {
+		ssi_ick: clock-ssi-ick-3430es1@0 {
+			reg = <0>;
 			#clock-cells = <0>;
 			compatible = "ti,omap3-no-wait-interface-clock";
 			clock-output-names = "ssi_ick_3430es1";
 			clocks = <&ssi_l4_ick>;
-			ti,bit-shift = <0>;
 		};
 
-		usb_l4_gate_ick: clock-usb-l4-gate-ick {
+		usb_l4_gate_ick: clock-usb-l4-gate-ick@5 {
+			reg = <5>;
 			#clock-cells = <0>;
 			compatible = "ti,composite-interface-clock";
 			clock-output-names = "usb_l4_gate_ick";
 			clocks = <&l4_ick>;
-			ti,bit-shift = <5>;
 		};
 	};
 
@@ -174,14 +177,15 @@ clock@e00 {
 		compatible = "ti,clksel";
 		reg = <0xe00>;
 		#clock-cells = <2>;
-		#address-cells = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		dss1_alwon_fck: clock-dss1-alwon-fck-3430es1 {
+		dss1_alwon_fck: clock-dss1-alwon-fck-3430es1@0 {
+			reg = <0>;
 			#clock-cells = <0>;
 			compatible = "ti,gate-clock";
 			clock-output-names = "dss1_alwon_fck_3430es1";
 			clocks = <&dpll4_m4x2_ck>;
-			ti,bit-shift = <0>;
 			ti,set-rate-parent;
 		};
 	};

arch/arm/boot/dts/ti/omap/omap34xx-omap36xx-clocks.dtsi

@@ -17,46 +17,47 @@ clock@a14 {
 		compatible = "ti,clksel";
 		reg = <0xa14>;
 		#clock-cells = <2>;
-		#address-cells = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		aes1_ick: clock-aes1-ick {
+		aes1_ick: clock-aes1-ick@3 {
+			reg = <3>;
 			#clock-cells = <0>;
 			compatible = "ti,omap3-interface-clock";
 			clock-output-names = "aes1_ick";
 			clocks = <&security_l4_ick2>;
-			ti,bit-shift = <3>;
 		};
 
-		rng_ick: clock-rng-ick {
+		rng_ick: clock-rng-ick@2 {
+			reg = <2>;
 			#clock-cells = <0>;
 			compatible = "ti,omap3-interface-clock";
 			clock-output-names = "rng_ick";
 			clocks = <&security_l4_ick2>;
-			ti,bit-shift = <2>;
 		};
 
-		sha11_ick: clock-sha11-ick {
+		sha11_ick: clock-sha11-ick@1 {
+			reg = <1>;
 			#clock-cells = <0>;
 			compatible = "ti,omap3-interface-clock";
 			clock-output-names = "sha11_ick";
 			clocks = <&security_l4_ick2>;
-			ti,bit-shift = <1>;
 		};
 
-		des1_ick: clock-des1-ick {
+		des1_ick: clock-des1-ick@0 {
+			reg = <0>;
 			#clock-cells = <0>;
 			compatible = "ti,omap3-interface-clock";
 			clock-output-names = "des1_ick";
 			clocks = <&security_l4_ick2>;
-			ti,bit-shift = <0>;
 		};
 
-		pka_ick: clock-pka-ick {
+		pka_ick: clock-pka-ick@4 {
+			reg = <4>;
 			#clock-cells = <0>;
 			compatible = "ti,omap3-interface-clock";
 			clock-output-names = "pka_ick";
 			clocks = <&security_l3_ick>;
-			ti,bit-shift = <4>;
 		};
 	};
 
@@ -65,23 +66,24 @@ clock@f00 {
 		compatible = "ti,clksel";
 		reg = <0xf00>;
 		#clock-cells = <2>;
-		#address-cells = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		cam_mclk: clock-cam-mclk {
+		cam_mclk: clock-cam-mclk@0 {
+			reg = <0>;
 			#clock-cells = <0>;
 			compatible = "ti,gate-clock";
 			clock-output-names = "cam_mclk";
 			clocks = <&dpll4_m5x2_ck>;
-			ti,bit-shift = <0>;
 			ti,set-rate-parent;
 		};
 
-		csi2_96m_fck: clock-csi2-96m-fck {
+		csi2_96m_fck: clock-csi2-96m-fck@1 {
+			reg = <1>;
 			#clock-cells = <0>;
 			compatible = "ti,gate-clock";
 			clock-output-names = "csi2_96m_fck";
 			clocks = <&core_96m_fck>;
-			ti,bit-shift = <1>;
 		};
 	};
 
@@ -105,46 +107,47 @@ clock@a10 {
 		compatible = "ti,clksel";
 		reg = <0xa10>;
 		#clock-cells = <2>;
-		#address-cells = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		icr_ick: clock-icr-ick {
+		icr_ick: clock-icr-ick@29 {
+			reg = <29>;
 			#clock-cells = <0>;
 			compatible = "ti,omap3-interface-clock";
 			clock-output-names = "icr_ick";
 			clocks = <&core_l4_ick>;
-			ti,bit-shift = <29>;
 		};
 
-		des2_ick: clock-des2-ick {
+		des2_ick: clock-des2-ick@26 {
+			reg = <26>;
 			#clock-cells = <0>;
 			compatible = "ti,omap3-interface-clock";
 			clock-output-names = "des2_ick";
 			clocks = <&core_l4_ick>;
-			ti,bit-shift = <26>;
 		};
 
-		mspro_ick: clock-mspro-ick {
+		mspro_ick: clock-mspro-ick@23 {
+			reg = <23>;
 			#clock-cells = <0>;
 			compatible = "ti,omap3-interface-clock";
 			clock-output-names = "mspro_ick";
 			clocks = <&core_l4_ick>;
-			ti,bit-shift = <23>;
 		};
 
-		mailboxes_ick: clock-mailboxes-ick {
+		mailboxes_ick: clock-mailboxes-ick@7 {
+			reg = <7>;
 			#clock-cells = <0>;
 			compatible = "ti,omap3-interface-clock";
 			clock-output-names = "mailboxes_ick";
 			clocks = <&core_l4_ick>;
-			ti,bit-shift = <7>;
 		};
 
-		sad2d_ick: clock-sad2d-ick {
+		sad2d_ick: clock-sad2d-ick@3 {
+			reg = <3>;
 			#clock-cells = <0>;
 			compatible = "ti,omap3-interface-clock";
 			clock-output-names = "sad2d_ick";
 			clocks = <&l3_ick>;
-			ti,bit-shift = <3>;
 		};
 	};
 
@@ -160,22 +163,23 @@ clock@c00 {
 		compatible = "ti,clksel";
 		reg = <0xc00>;
 		#clock-cells = <2>;
-		#address-cells = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		sr1_fck: clock-sr1-fck {
+		sr1_fck: clock-sr1-fck@6 {
+			reg = <6>;
 			#clock-cells = <0>;
 			compatible = "ti,wait-gate-clock";
 			clock-output-names = "sr1_fck";
 			clocks = <&sys_ck>;
-			ti,bit-shift = <6>;
 		};
 
-		sr2_fck: clock-sr2-fck {
+		sr2_fck: clock-sr2-fck@7 {
+			reg = <7>;
 			#clock-cells = <0>;
 			compatible = "ti,wait-gate-clock";
 			clock-output-names = "sr2_fck";
 			clocks = <&sys_ck>;
-			ti,bit-shift = <7>;
 		};
 	};
 
@@ -228,22 +232,23 @@ clock@a00 {
 		compatible = "ti,clksel";
 		reg = <0xa00>;
 		#clock-cells = <2>;
-		#address-cells = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		modem_fck: clock-modem-fck {
+		modem_fck: clock-modem-fck@31 {
+			reg = <31>;
 			#clock-cells = <0>;
 			compatible = "ti,omap3-interface-clock";
 			clock-output-names = "modem_fck";
 			clocks = <&sys_ck>;
-			ti,bit-shift = <31>;
 		};
 
-		mspro_fck: clock-mspro-fck {
+		mspro_fck: clock-mspro-fck@23 {
+			reg = <23>;
 			#clock-cells = <0>;
 			compatible = "ti,wait-gate-clock";
 			clock-output-names = "mspro_fck";
 			clocks = <&core_96m_fck>;
-			ti,bit-shift = <23>;
 		};
 	};
 
@@ -252,14 +257,15 @@ clock@a18 {
 		compatible = "ti,clksel";
 		reg = <0xa18>;
 		#clock-cells = <2>;
-		#address-cells = <0>;
+		#address-cells = <1>;
+		#ssize-cells = <0>;
 
-		mad2d_ick: clock-mad2d-ick {
+		mad2d_ick: clock-mad2d-ick@3 {
+			reg = <3>;
 			#clock-cells = <0>;
 			compatible = "ti,omap3-interface-clock";
 			clock-output-names = "mad2d_ick";
 			clocks = <&l3_ick>;
-			ti,bit-shift = <3>;
 		};
 	};
 

arch/arm/boot/dts/ti/omap/omap36xx-am35xx-omap3430es2plus-clocks.dtsi

@@ -138,14 +138,15 @@ clock@a18 {
 		compatible = "ti,clksel";
 		reg = <0xa18>;
 		#clock-cells = <2>;
-		#address-cells = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		usbtll_ick: clock-usbtll-ick {
+		usbtll_ick: clock-usbtll-ick@2 {
+			reg = <2>;
 			#clock-cells = <0>;
 			compatible = "ti,omap3-interface-clock";
 			clock-output-names = "usbtll_ick";
 			clocks = <&core_l4_ick>;
-			ti,bit-shift = <2>;
 		};
 	};
 
@@ -153,14 +154,15 @@ clock@a10 {
 		compatible = "ti,clksel";
 		reg = <0xa10>;
 		#clock-cells = <2>;
-		#address-cells = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		mmchs3_ick: clock-mmchs3-ick {
+		mmchs3_ick: clock-mmchs3-ick@30 {
+			reg = <30>;
 			#clock-cells = <0>;
 			compatible = "ti,omap3-interface-clock";
 			clock-output-names = "mmchs3_ick";
 			clocks = <&core_l4_ick>;
-			ti,bit-shift = <30>;
 		};
 	};
 
@@ -168,14 +170,15 @@ clock@a00 {
 		compatible = "ti,clksel";
 		reg = <0xa00>;
 		#clock-cells = <2>;
-		#address-cells = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		mmchs3_fck: clock-mmchs3-fck {
+		mmchs3_fck: clock-mmchs3-fck@30 {
+			reg = <30>;
 			#clock-cells = <0>;
 			compatible = "ti,wait-gate-clock";
 			clock-output-names = "mmchs3_fck";
 			clocks = <&core_96m_fck>;
-			ti,bit-shift = <30>;
 		};
 	};
 
@@ -183,14 +186,15 @@ clock@e00 {
 		compatible = "ti,clksel";
 		reg = <0xe00>;
 		#clock-cells = <2>;
-		#address-cells = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		dss1_alwon_fck: clock-dss1-alwon-fck-3430es2 {
+		dss1_alwon_fck: clock-dss1-alwon-fck-3430es2@0 {
+			reg = <0>;
 			#clock-cells = <0>;
 			compatible = "ti,dss-gate-clock";
 			clock-output-names = "dss1_alwon_fck_3430es2";
 			clocks = <&dpll4_m4x2_ck>;
-			ti,bit-shift = <0>;
 			ti,set-rate-parent;
 		};
 	};

arch/arm/boot/dts/ti/omap/omap36xx-clocks.dtsi

@@ -62,14 +62,15 @@ clock@1000 {
 		compatible = "ti,clksel";
 		reg = <0x1000>;
 		#clock-cells = <2>;
-		#address-cells = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		uart4_fck: clock-uart4-fck {
+		uart4_fck: clock-uart4-fck@18 {
+			reg = <18>;
 			#clock-cells = <0>;
 			compatible = "ti,wait-gate-clock";
 			clock-output-names = "uart4_fck";
 			clocks = <&per_48m_fck>;
-			ti,bit-shift = <18>;
 		};
 	};
 };

arch/arm/boot/dts/ti/omap/omap36xx-omap3430es2plus-clocks.dtsi

@@ -9,14 +9,15 @@ clock@a00 {
 		compatible = "ti,clksel";
 		reg = <0xa00>;
 		#clock-cells = <2>;
-		#address-cells = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		ssi_ssr_gate_fck_3430es2: clock-ssi-ssr-gate-fck-3430es2 {
+		ssi_ssr_gate_fck_3430es2: clock-ssi-ssr-gate-fck-3430es2@0 {
+			reg = <0>;
 			#clock-cells = <0>;
 			compatible = "ti,composite-no-wait-gate-clock";
 			clock-output-names = "ssi_ssr_gate_fck_3430es2";
 			clocks = <&corex2_fck>;
-			ti,bit-shift = <0>;
 		};
 	};
 
@@ -24,14 +25,15 @@ clock@a40 {
 		compatible = "ti,clksel";
 		reg = <0xa40>;
 		#clock-cells = <2>;
-		#address-cells = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		ssi_ssr_div_fck_3430es2: clock-ssi-ssr-div-fck-3430es2 {
+		ssi_ssr_div_fck_3430es2: clock-ssi-ssr-div-fck-3430es2@8 {
+			reg = <8>;
 			#clock-cells = <0>;
 			compatible = "ti,composite-divider-clock";
 			clock-output-names = "ssi_ssr_div_fck_3430es2";
 			clocks = <&corex2_fck>;
-			ti,bit-shift = <8>;
 			ti,dividers = <0>, <1>, <2>, <3>, <4>, <0>, <6>, <0>, <8>;
 		};
 	};
@@ -54,22 +56,23 @@ clock@a10 {
 		compatible = "ti,clksel";
 		reg = <0xa10>;
 		#clock-cells = <2>;
-		#address-cells = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		hsotgusb_ick_3430es2: clock-hsotgusb-ick-3430es2 {
+		hsotgusb_ick_3430es2: clock-hsotgusb-ick-3430es2@4 {
+			reg = <4>;
 			#clock-cells = <0>;
 			compatible = "ti,omap3-hsotgusb-interface-clock";
 			clock-output-names = "hsotgusb_ick_3430es2";
 			clocks = <&core_l3_ick>;
-			ti,bit-shift = <4>;
 		};
 
-		ssi_ick: clock-ssi-ick-3430es2 {
+		ssi_ick: clock-ssi-ick-3430es2@0 {
+			reg = <0>;
 			#clock-cells = <0>;
 			compatible = "ti,omap3-ssi-interface-clock";
 			clock-output-names = "ssi_ick_3430es2";
 			clocks = <&ssi_l4_ick>;
-			ti,bit-shift = <0>;
 		};
 	};
 
@@ -85,14 +88,15 @@ clock@c00 {
 		compatible = "ti,clksel";
 		reg = <0xc00>;
 		#clock-cells = <2>;
-		#address-cells = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		usim_gate_fck: clock-usim-gate-fck {
+		usim_gate_fck: clock-usim-gate-fck@9 {
+			reg = <9>;
 			#clock-cells = <0>;
 			compatible = "ti,composite-gate-clock";
 			clock-output-names = "usim_gate_fck";
 			clocks = <&omap_96m_fck>;
-			ti,bit-shift = <9>;
 		};
 	};
 
@@ -172,14 +176,15 @@ clock@c40 {
 		compatible = "ti,clksel";
 		reg = <0xc40>;
 		#clock-cells = <2>;
-		#address-cells = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		usim_mux_fck: clock-usim-mux-fck {
+		usim_mux_fck: clock-usim-mux-fck@3 {
+			reg = <3>;
 			#clock-cells = <0>;
 			compatible = "ti,composite-mux-clock";
 			clock-output-names = "usim_mux_fck";
 			clocks = <&sys_ck>, <&sys_d2_ck>, <&omap_96m_d2_fck>, <&omap_96m_d4_fck>, <&omap_96m_d8_fck>, <&omap_96m_d10_fck>, <&dpll5_m2_d4_ck>, <&dpll5_m2_d8_ck>, <&dpll5_m2_d16_ck>, <&dpll5_m2_d20_ck>;
-			ti,bit-shift = <3>;
 			ti,index-starts-at-one;
 		};
 	};
@@ -194,14 +199,15 @@ clock@c10 {
 		compatible = "ti,clksel";
 		reg = <0xc10>;
 		#clock-cells = <2>;
-		#address-cells = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		usim_ick: clock-usim-ick {
+		usim_ick: clock-usim-ick@9 {
+			reg = <9>;
 			#clock-cells = <0>;
 			compatible = "ti,omap3-interface-clock";
 			clock-output-names = "usim_ick";
 			clocks = <&wkup_l4_ick>;
-			ti,bit-shift = <9>;
 		};
 	};
 };

arch/arm/include/debug/brcmstb.S

@@ -27,6 +27,7 @@
 #define UARTA_72165		UARTA_7278
 #define UARTA_7364		REG_PHYS_ADDR(0x40b000)
 #define UARTA_7366		UARTA_7364
+#define UARTA_74165		UARTA_7278
 #define UARTA_74371		REG_PHYS_ADDR(0x406b00)
 #define UARTA_7439		REG_PHYS_ADDR(0x40a900)
 #define UARTA_7445		REG_PHYS_ADDR(0x40ab00)
@@ -88,9 +89,10 @@ ARM_BE8(	rev	\rv, \rv )
 30:		checkuart(\rp, \rv, 0x72780000, 7278)
 31:		checkuart(\rp, \rv, 0x73640000, 7364)
 32:		checkuart(\rp, \rv, 0x73660000, 7366)
-33:		checkuart(\rp, \rv, 0x07437100, 74371)
-34:		checkuart(\rp, \rv, 0x74390000, 7439)
-35:		checkuart(\rp, \rv, 0x74450000, 7445)
+33:		checkuart(\rp, \rv, 0x07416500, 74165)
+34:		checkuart(\rp, \rv, 0x07437100, 74371)
+35:		checkuart(\rp, \rv, 0x74390000, 7439)
+36:		checkuart(\rp, \rv, 0x74450000, 7445)
 
 		/* No valid UART found */
 90:		mov	\rp, #0

arch/arm/mach-bcm/Kconfig

@@ -93,7 +93,6 @@ config ARCH_BCM_MOBILE
 	select ARM_ERRATA_775420
 	select ARM_GIC
 	select GPIO_BCM_KONA
-	select TICK_ONESHOT
 	select HAVE_ARM_ARCH_TIMER
 	select PINCTRL
 	select ARCH_BCM_MOBILE_SMP if SMP

arch/arm64/boot/dts/broadcom/bcmbca/bcm4908-asus-gt-ac5300.dts

@@ -185,18 +185,19 @@ partitions {
 		#size-cells = <1>;
 
 		partition@0 {
-			compatible = "nvmem-cells";
 			label = "cferom";
 			reg = <0x0 0x100000>;
 
+			nvmem-layout {
+				compatible = "fixed-layout";
 				#address-cells = <1>;
 				#size-cells = <1>;
-			ranges = <0 0x0 0x100000>;
 
 				base_mac_addr: mac@106a0 {
 					reg = <0x106a0 0x6>;
 				};
 			};
+		};
 
 		partition@100000 {
 			compatible = "brcm,bcm4908-firmware";

arch/arm64/boot/dts/broadcom/bcmbca/bcm4908.dtsi

@@ -227,9 +227,6 @@ ethernet-switch@0 {
 				brcm,num-gphy = <5>;
 				brcm,num-rgmii-ports = <2>;
 
-				#address-cells = <1>;
-				#size-cells = <0>;
-
 				ports: ports {
 					#address-cells = <1>;
 					#size-cells = <0>;

arch/riscv/boot/dts/microchip/mpfs.dtsi

@@ -243,7 +243,7 @@ plic: interrupt-controller@c000000 {
 		};
 
 		pdma: dma-controller@3000000 {
-			compatible = "sifive,fu540-c000-pdma", "sifive,pdma0";
+			compatible = "microchip,mpfs-pdma", "sifive,pdma0";
 			reg = <0x0 0x3000000 0x0 0x8000>;
 			interrupt-parent = <&plic>;
 			interrupts = <5 6>, <7 8>, <9 10>, <11 12>;
@@ -422,7 +422,7 @@ i2c1: i2c@2010b000 {
 		can0: can@2010c000 {
 			compatible = "microchip,mpfs-can";
 			reg = <0x0 0x2010c000 0x0 0x1000>;
-			clocks = <&clkcfg CLK_CAN0>;
+			clocks = <&clkcfg CLK_CAN0>, <&clkcfg CLK_MSSPLL3>;
 			interrupt-parent = <&plic>;
 			interrupts = <56>;
 			status = "disabled";
@@ -431,7 +431,7 @@ can0: can@2010c000 {
 		can1: can@2010d000 {
 			compatible = "microchip,mpfs-can";
 			reg = <0x0 0x2010d000 0x0 0x1000>;
-			clocks = <&clkcfg CLK_CAN1>;
+			clocks = <&clkcfg CLK_CAN1>, <&clkcfg CLK_MSSPLL3>;
 			interrupt-parent = <&plic>;
 			interrupts = <57>;
 			status = "disabled";

arch/riscv/boot/dts/starfive/jh7100-beaglev-starlight.dts

@@ -11,3 +11,14 @@ / {
 	model = "BeagleV Starlight Beta";
 	compatible = "beagle,beaglev-starlight-jh7100-r0", "starfive,jh7100";
 };
+
+&gmac {
+	phy-handle = <&phy>;
+};
+
+&mdio {
+	phy: ethernet-phy@7 {
+		reg = <7>;
+		reset-gpios = <&gpio 63 GPIO_ACTIVE_LOW>;
+	};
+};

arch/riscv/boot/dts/starfive/jh7100-common.dtsi

@@ -72,7 +72,91 @@ wifi_pwrseq: wifi-pwrseq {
 	};
 };
 
+&gmac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac_pins>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	mdio: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+	};
+};
+
 &gpio {
+	gmac_pins: gmac-0 {
+		gtxclk-pins {
+			pins = <PAD_FUNC_SHARE(115)>;
+			bias-pull-up;
+			drive-strength = <35>;
+			input-enable;
+			input-schmitt-enable;
+			slew-rate = <0>;
+		};
+		miitxclk-pins {
+			pins = <PAD_FUNC_SHARE(116)>;
+			bias-pull-up;
+			drive-strength = <14>;
+			input-enable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+		tx-pins {
+			pins = <PAD_FUNC_SHARE(117)>,
+			       <PAD_FUNC_SHARE(119)>,
+			       <PAD_FUNC_SHARE(120)>,
+			       <PAD_FUNC_SHARE(121)>,
+			       <PAD_FUNC_SHARE(122)>,
+			       <PAD_FUNC_SHARE(123)>,
+			       <PAD_FUNC_SHARE(124)>,
+			       <PAD_FUNC_SHARE(125)>,
+			       <PAD_FUNC_SHARE(126)>;
+			bias-pull-up;
+			drive-strength = <35>;
+			input-disable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+		rxclk-pins {
+			pins = <PAD_FUNC_SHARE(127)>;
+			bias-pull-up;
+			drive-strength = <14>;
+			input-enable;
+			input-schmitt-disable;
+			slew-rate = <6>;
+		};
+		rxer-pins {
+			pins = <PAD_FUNC_SHARE(129)>;
+			bias-pull-up;
+			drive-strength = <14>;
+			input-enable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+		rx-pins {
+			pins = <PAD_FUNC_SHARE(128)>,
+			       <PAD_FUNC_SHARE(130)>,
+			       <PAD_FUNC_SHARE(131)>,
+			       <PAD_FUNC_SHARE(132)>,
+			       <PAD_FUNC_SHARE(133)>,
+			       <PAD_FUNC_SHARE(134)>,
+			       <PAD_FUNC_SHARE(135)>,
+			       <PAD_FUNC_SHARE(136)>,
+			       <PAD_FUNC_SHARE(137)>,
+			       <PAD_FUNC_SHARE(138)>,
+			       <PAD_FUNC_SHARE(139)>,
+			       <PAD_FUNC_SHARE(140)>,
+			       <PAD_FUNC_SHARE(141)>;
+			bias-pull-up;
+			drive-strength = <14>;
+			input-enable;
+			input-schmitt-enable;
+			slew-rate = <0>;
+		};
+	};
+
 	i2c0_pins: i2c0-0 {
 		i2c-pins {
 			pinmux = <GPIOMUX(62, GPO_LOW,
@@ -115,6 +199,24 @@ GPO_I2C2_PAD_SDA_OEN,
 		};
 	};
 
+	pwm_pins: pwm-0 {
+		pwm-pins {
+			pinmux = <GPIOMUX(7,
+				  GPO_PWM_PAD_OUT_BIT0,
+				  GPO_PWM_PAD_OE_N_BIT0,
+				  GPI_NONE)>,
+				 <GPIOMUX(5,
+				  GPO_PWM_PAD_OUT_BIT1,
+				  GPO_PWM_PAD_OE_N_BIT1,
+				  GPI_NONE)>;
+			bias-disable;
+			drive-strength = <35>;
+			input-disable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+	};
+
 	sdio0_pins: sdio0-0 {
 		clk-pins {
 			pinmux = <GPIOMUX(54, GPO_SDIO0_PAD_CCLK_OUT,
@@ -257,6 +359,12 @@ &osc_aud {
 	clock-frequency = <27000000>;
 };
 
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm_pins>;
+	status = "okay";
+};
+
 &sdio0 {
 	broken-cd;
 	bus-width = <4>;

arch/riscv/boot/dts/starfive/jh7100-starfive-visionfive-v1.dts

@@ -6,7 +6,6 @@
 
 /dts-v1/;
 #include "jh7100-common.dtsi"
-#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "StarFive VisionFive V1";
@@ -18,3 +17,24 @@ gpio-restart {
 		priority = <224>;
 	};
 };
+
+&gmac {
+	phy-handle = <&phy>;
+};
+
+/*
+ * The board uses a Motorcomm YT8521 PHY supporting RGMII-ID, but requires
+ * manual adjustment of the RX internal delay to work properly.  The default
+ * RX delay provided by the driver (1.95ns) is too high, but applying a 50%
+ * reduction seems to mitigate the issue.
+ *
+ * It is worth noting the adjustment is not necessary on BeagleV Starlight SBC,
+ * which uses a Microchip PHY.  Hence, most likely the Motorcomm PHY is the one
+ * responsible for the misbehaviour, not the GMAC.
+ */
+&mdio {
+	phy: ethernet-phy@0 {
+		reg = <0>;
+		rx-internal-delay-ps = <900>;
+	};
+};

arch/riscv/boot/dts/starfive/jh7100.dtsi

@@ -208,6 +208,37 @@ sdio1: mmc@10010000 {
 			status = "disabled";
 		};
 
+		gmac: ethernet@10020000 {
+			compatible = "starfive,jh7100-dwmac", "snps,dwmac";
+			reg = <0x0 0x10020000 0x0 0x10000>;
+			clocks = <&clkgen JH7100_CLK_GMAC_ROOT_DIV>,
+				 <&clkgen JH7100_CLK_GMAC_AHB>,
+				 <&clkgen JH7100_CLK_GMAC_PTP_REF>,
+				 <&clkgen JH7100_CLK_GMAC_TX_INV>,
+				 <&clkgen JH7100_CLK_GMAC_GTX>;
+			clock-names = "stmmaceth", "pclk", "ptp_ref", "tx", "gtx";
+			resets = <&rstgen JH7100_RSTN_GMAC_AHB>;
+			reset-names = "ahb";
+			interrupts = <6>, <7>;
+			interrupt-names = "macirq", "eth_wake_irq";
+			max-frame-size = <9000>;
+			snps,multicast-filter-bins = <32>;
+			snps,perfect-filter-entries = <128>;
+			starfive,syscon = <&sysmain 0x70 0>;
+			rx-fifo-depth = <32768>;
+			tx-fifo-depth = <16384>;
+			snps,axi-config = <&stmmac_axi_setup>;
+			snps,fixed-burst;
+			snps,force_thresh_dma_mode;
+			status = "disabled";
+
+			stmmac_axi_setup: stmmac-axi-config {
+				snps,wr_osr_lmt = <16>;
+				snps,rd_osr_lmt = <16>;
+				snps,blen = <256 128 64 32 0 0 0>;
+			};
+		};
+
 		clkgen: clock-controller@11800000 {
 			compatible = "starfive,jh7100-clkgen";
 			reg = <0x0 0x11800000 0x0 0x10000>;
@@ -222,6 +253,11 @@ rstgen: reset-controller@11840000 {
 			#reset-cells = <1>;
 		};
 
+		sysmain: syscon@11850000 {
+			compatible = "starfive,jh7100-sysmain", "syscon";
+			reg = <0x0 0x11850000 0x0 0x10000>;
+		};
+
 		i2c0: i2c@118b0000 {
 			compatible = "snps,designware-i2c";
 			reg = <0x0 0x118b0000 0x0 0x10000>;
@@ -324,6 +360,15 @@ watchdog@12480000 {
 				 <&rstgen JH7100_RSTN_WDT>;
 		};
 
+		pwm: pwm@12490000 {
+			compatible = "starfive,jh7100-pwm", "opencores,pwm-v1";
+			reg = <0x0 0x12490000 0x0 0x10000>;
+			clocks = <&clkgen JH7100_CLK_PWM_APB>;
+			resets = <&rstgen JH7100_RSTN_PWM_APB>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
 		sfctemp: temperature-sensor@124a0000 {
 			compatible = "starfive,jh7100-temp";
 			reg = <0x0 0x124a0000 0x0 0x10000>;

arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi

@@ -125,6 +125,55 @@ &tdm_ext {
 	clock-frequency = <49152000>;
 };
 
+&camss {
+	assigned-clocks = <&ispcrg JH7110_ISPCLK_DOM4_APB_FUNC>,
+			  <&ispcrg JH7110_ISPCLK_MIPI_RX0_PXL>;
+	assigned-clock-rates = <49500000>, <198000000>;
+	status = "okay";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+		};
+
+		port@1 {
+			reg = <1>;
+
+			camss_from_csi2rx: endpoint {
+				remote-endpoint = <&csi2rx_to_camss>;
+			};
+		};
+	};
+};
+
+&csi2rx {
+	assigned-clocks = <&ispcrg JH7110_ISPCLK_VIN_SYS>;
+	assigned-clock-rates = <297000000>;
+	status = "okay";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			/* remote MIPI sensor endpoint */
+		};
+
+		port@1 {
+			reg = <1>;
+
+			csi2rx_to_camss: endpoint {
+				remote-endpoint = <&camss_from_csi2rx>;
+			};
+		};
+	};
+};
+
 &gmac0 {
 	phy-handle = <&phy0>;
 	phy-mode = "rgmii-id";
@@ -323,6 +372,12 @@ reserved-data@600000 {
 	};
 };
 
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm_pins>;
+	status = "okay";
+};
+
 &spi0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&spi0_pins>;
@@ -513,6 +568,22 @@ GPOEN_ENABLE,
 		};
 	};
 
+	pwm_pins: pwm-0 {
+		pwm-pins {
+			pinmux = <GPIOMUX(46, GPOUT_SYS_PWM_CHANNEL0,
+					      GPOEN_SYS_PWM0_CHANNEL0,
+					      GPI_NONE)>,
+				 <GPIOMUX(59, GPOUT_SYS_PWM_CHANNEL1,
+					      GPOEN_SYS_PWM0_CHANNEL1,
+					      GPI_NONE)>;
+			bias-disable;
+			drive-strength = <12>;
+			input-disable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+	};
+
 	spi0_pins: spi0-0 {
 		mosi-pins {
 			pinmux = <GPIOMUX(52, GPOUT_SYS_SPI0_TXD,

arch/riscv/boot/dts/starfive/jh7110.dtsi

@@ -829,6 +829,15 @@ i2stx1: i2s@120c0000 {
 			status = "disabled";
 		};
 
+		pwm: pwm@120d0000 {
+			compatible = "starfive,jh7110-pwm", "opencores,pwm-v1";
+			reg = <0x0 0x120d0000 0x0 0x10000>;
+			clocks = <&syscrg JH7110_SYSCLK_PWM_APB>;
+			resets = <&syscrg JH7110_SYSRST_PWM_APB>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
 		sfctemp: temperature-sensor@120e0000 {
 			compatible = "starfive,jh7110-temp";
 			reg = <0x0 0x120e0000 0x0 0x10000>;
@@ -1104,6 +1113,32 @@ pwrc: power-controller@17030000 {
 			#power-domain-cells = <1>;
 		};
 
+		csi2rx: csi@19800000 {
+			compatible = "starfive,jh7110-csi2rx", "cdns,csi2rx";
+			reg = <0x0 0x19800000 0x0 0x10000>;
+			clocks = <&ispcrg JH7110_ISPCLK_VIN_SYS>,
+				 <&ispcrg JH7110_ISPCLK_VIN_APB>,
+				 <&ispcrg JH7110_ISPCLK_VIN_PIXEL_IF0>,
+				 <&ispcrg JH7110_ISPCLK_VIN_PIXEL_IF1>,
+				 <&ispcrg JH7110_ISPCLK_VIN_PIXEL_IF2>,
+				 <&ispcrg JH7110_ISPCLK_VIN_PIXEL_IF3>;
+			clock-names = "sys_clk", "p_clk",
+				      "pixel_if0_clk", "pixel_if1_clk",
+				      "pixel_if2_clk", "pixel_if3_clk";
+			resets = <&ispcrg JH7110_ISPRST_VIN_SYS>,
+				 <&ispcrg JH7110_ISPRST_VIN_APB>,
+				 <&ispcrg JH7110_ISPRST_VIN_PIXEL_IF0>,
+				 <&ispcrg JH7110_ISPRST_VIN_PIXEL_IF1>,
+				 <&ispcrg JH7110_ISPRST_VIN_PIXEL_IF2>,
+				 <&ispcrg JH7110_ISPRST_VIN_PIXEL_IF3>;
+			reset-names = "sys", "reg_bank",
+				      "pixel_if0", "pixel_if1",
+				      "pixel_if2", "pixel_if3";
+			phys = <&csi_phy>;
+			phy-names = "dphy";
+			status = "disabled";
+		};
+
 		ispcrg: clock-controller@19810000 {
 			compatible = "starfive,jh7110-ispcrg";
 			reg = <0x0 0x19810000 0x0 0x10000>;
@@ -1121,6 +1156,47 @@ ispcrg: clock-controller@19810000 {
 			power-domains = <&pwrc JH7110_PD_ISP>;
 		};
 
+		csi_phy: phy@19820000 {
+			compatible = "starfive,jh7110-dphy-rx";
+			reg = <0x0 0x19820000 0x0 0x10000>;
+			clocks = <&ispcrg JH7110_ISPCLK_M31DPHY_CFG_IN>,
+				 <&ispcrg JH7110_ISPCLK_M31DPHY_REF_IN>,
+				 <&ispcrg JH7110_ISPCLK_M31DPHY_TX_ESC_LAN0>;
+			clock-names = "cfg", "ref", "tx";
+			resets = <&ispcrg JH7110_ISPRST_M31DPHY_HW>,
+				 <&ispcrg JH7110_ISPRST_M31DPHY_B09_AON>;
+			power-domains = <&aon_syscon JH7110_AON_PD_DPHY_RX>;
+			#phy-cells = <0>;
+		};
+
+		camss: isp@19840000 {
+			compatible = "starfive,jh7110-camss";
+			reg = <0x0 0x19840000 0x0 0x10000>,
+			      <0x0 0x19870000 0x0 0x30000>;
+			reg-names = "syscon", "isp";
+			clocks = <&ispcrg JH7110_ISPCLK_DOM4_APB_FUNC>,
+				 <&ispcrg JH7110_ISPCLK_ISPV2_TOP_WRAPPER_C>,
+				 <&ispcrg JH7110_ISPCLK_DVP_INV>,
+				 <&ispcrg JH7110_ISPCLK_VIN_P_AXI_WR>,
+				 <&ispcrg JH7110_ISPCLK_MIPI_RX0_PXL>,
+				 <&syscrg JH7110_SYSCLK_ISP_TOP_CORE>,
+				 <&syscrg JH7110_SYSCLK_ISP_TOP_AXI>;
+			clock-names = "apb_func", "wrapper_clk_c", "dvp_inv",
+				      "axiwr", "mipi_rx0_pxl", "ispcore_2x",
+				      "isp_axi";
+			resets = <&ispcrg JH7110_ISPRST_ISPV2_TOP_WRAPPER_P>,
+				 <&ispcrg JH7110_ISPRST_ISPV2_TOP_WRAPPER_C>,
+				 <&ispcrg JH7110_ISPRST_VIN_P_AXI_RD>,
+				 <&ispcrg JH7110_ISPRST_VIN_P_AXI_WR>,
+				 <&syscrg JH7110_SYSRST_ISP_TOP>,
+				 <&syscrg JH7110_SYSRST_ISP_TOP_AXI>;
+			reset-names = "wrapper_p", "wrapper_c", "axird",
+				      "axiwr", "isp_top_n", "isp_top_axi";
+			power-domains = <&pwrc JH7110_PD_ISP>;
+			interrupts = <92>, <87>, <90>, <88>;
+			status = "disabled";
+		};
+
 		voutcrg: clock-controller@295c0000 {
 			compatible = "starfive,jh7110-voutcrg";
 			reg = <0x0 0x295c0000 0x0 0x10000>;

drivers/bus/brcmstb_gisb.c

@@ -96,6 +96,20 @@ static const int gisb_offsets_bcm7400[] = {
 	[ARB_ERR_CAP_MASTER]	= 0x0d8,
 };
 
+static const int gisb_offsets_bcm74165[] = {
+	[ARB_TIMER]		= 0x008,
+	[ARB_BP_CAP_CLR]	= 0x044,
+	[ARB_BP_CAP_HI_ADDR]	= -1,
+	[ARB_BP_CAP_ADDR]	= 0x048,
+	[ARB_BP_CAP_STATUS]	= 0x058,
+	[ARB_BP_CAP_MASTER]	= 0x05c,
+	[ARB_ERR_CAP_CLR]	= 0x038,
+	[ARB_ERR_CAP_HI_ADDR]	= -1,
+	[ARB_ERR_CAP_ADDR]	= 0x020,
+	[ARB_ERR_CAP_STATUS]	= 0x030,
+	[ARB_ERR_CAP_MASTER]	= 0x034,
+};
+
 static const int gisb_offsets_bcm7435[] = {
 	[ARB_TIMER]		= 0x00c,
 	[ARB_BP_CAP_CLR]	= 0x014,
@@ -393,6 +407,7 @@ static const struct of_device_id brcmstb_gisb_arb_of_match[] = {
 	{ .compatible = "brcm,bcm7400-gisb-arb", .data = gisb_offsets_bcm7400 },
 	{ .compatible = "brcm,bcm7278-gisb-arb", .data = gisb_offsets_bcm7278 },
 	{ .compatible = "brcm,bcm7038-gisb-arb", .data = gisb_offsets_bcm7038 },
+	{ .compatible = "brcm,bcm74165-gisb-arb", .data = gisb_offsets_bcm74165 },
 	{ },
 };
 

drivers/bus/ts-nbus.c

@@ -39,45 +39,39 @@ struct ts_nbus {
 /*
  * request all gpios required by the bus.
  */
-static int ts_nbus_init_pdata(struct platform_device *pdev, struct ts_nbus
-		*ts_nbus)
+static int ts_nbus_init_pdata(struct platform_device *pdev,
+			      struct ts_nbus *ts_nbus)
 {
 	ts_nbus->data = devm_gpiod_get_array(&pdev->dev, "ts,data",
 			GPIOD_OUT_HIGH);
-	if (IS_ERR(ts_nbus->data)) {
-		dev_err(&pdev->dev, "failed to retrieve ts,data-gpio from dts\n");
-		return PTR_ERR(ts_nbus->data);
-	}
+	if (IS_ERR(ts_nbus->data))
+		return dev_err_probe(&pdev->dev, PTR_ERR(ts_nbus->data),
+				     "failed to retrieve ts,data-gpio from dts\n");
 
 	ts_nbus->csn = devm_gpiod_get(&pdev->dev, "ts,csn", GPIOD_OUT_HIGH);
-	if (IS_ERR(ts_nbus->csn)) {
-		dev_err(&pdev->dev, "failed to retrieve ts,csn-gpio from dts\n");
-		return PTR_ERR(ts_nbus->csn);
-	}
+	if (IS_ERR(ts_nbus->csn))
+		return dev_err_probe(&pdev->dev, PTR_ERR(ts_nbus->csn),
+			      "failed to retrieve ts,csn-gpio from dts\n");
 
 	ts_nbus->txrx = devm_gpiod_get(&pdev->dev, "ts,txrx", GPIOD_OUT_HIGH);
-	if (IS_ERR(ts_nbus->txrx)) {
-		dev_err(&pdev->dev, "failed to retrieve ts,txrx-gpio from dts\n");
-		return PTR_ERR(ts_nbus->txrx);
-	}
+	if (IS_ERR(ts_nbus->txrx))
+		return dev_err_probe(&pdev->dev, PTR_ERR(ts_nbus->txrx),
+				     "failed to retrieve ts,txrx-gpio from dts\n");
 
 	ts_nbus->strobe = devm_gpiod_get(&pdev->dev, "ts,strobe", GPIOD_OUT_HIGH);
-	if (IS_ERR(ts_nbus->strobe)) {
-		dev_err(&pdev->dev, "failed to retrieve ts,strobe-gpio from dts\n");
-		return PTR_ERR(ts_nbus->strobe);
-	}
+	if (IS_ERR(ts_nbus->strobe))
+		return dev_err_probe(&pdev->dev, PTR_ERR(ts_nbus->strobe),
+				     "failed to retrieve ts,strobe-gpio from dts\n");
 
 	ts_nbus->ale = devm_gpiod_get(&pdev->dev, "ts,ale", GPIOD_OUT_HIGH);
-	if (IS_ERR(ts_nbus->ale)) {
-		dev_err(&pdev->dev, "failed to retrieve ts,ale-gpio from dts\n");
-		return PTR_ERR(ts_nbus->ale);
-	}
+	if (IS_ERR(ts_nbus->ale))
+		return dev_err_probe(&pdev->dev, PTR_ERR(ts_nbus->ale),
+				     "failed to retrieve ts,ale-gpio from dts\n");
 
 	ts_nbus->rdy = devm_gpiod_get(&pdev->dev, "ts,rdy", GPIOD_IN);
-	if (IS_ERR(ts_nbus->rdy)) {
-		dev_err(&pdev->dev, "failed to retrieve ts,rdy-gpio from dts\n");
-		return PTR_ERR(ts_nbus->rdy);
-	}
+	if (IS_ERR(ts_nbus->rdy))
+		return dev_err_probe(&pdev->dev, PTR_ERR(ts_nbus->rdy),
+				     "failed to retrieve ts,rdy-gpio from dts\n");
 
 	return 0;
 }
@@ -273,7 +267,7 @@ EXPORT_SYMBOL_GPL(ts_nbus_write);
 static int ts_nbus_probe(struct platform_device *pdev)
 {
 	struct pwm_device *pwm;
-	struct pwm_args pargs;
+	struct pwm_state state;
 	struct device *dev = &pdev->dev;
 	struct ts_nbus *ts_nbus;
 	int ret;
@@ -289,32 +283,24 @@ static int ts_nbus_probe(struct platform_device *pdev)
 		return ret;
 
 	pwm = devm_pwm_get(dev, NULL);
-	if (IS_ERR(pwm)) {
-		ret = PTR_ERR(pwm);
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "unable to request PWM\n");
-		return ret;
-	}
+	if (IS_ERR(pwm))
+		return dev_err_probe(dev, PTR_ERR(pwm),
+				     "unable to request PWM\n");
 
-	pwm_get_args(pwm, &pargs);
-	if (!pargs.period) {
-		dev_err(&pdev->dev, "invalid PWM period\n");
-		return -EINVAL;
-	}
+	pwm_init_state(pwm, &state);
+	if (!state.period)
+		return dev_err_probe(dev, -EINVAL, "invalid PWM period\n");
 
-	/*
-	 * FIXME: pwm_apply_args() should be removed when switching to
-	 * the atomic PWM API.
-	 */
-	pwm_apply_args(pwm);
-	ret = pwm_config(pwm, pargs.period, pargs.period);
+	state.duty_cycle = state.period;
+	state.enabled = true;
+
+	ret = pwm_apply_state(pwm, &state);
 	if (ret < 0)
-		return ret;
+		return dev_err_probe(dev, ret, "failed to configure PWM\n");
 
 	/*
 	 * we can now start the FPGA and populate the peripherals.
 	 */
-	pwm_enable(pwm);
 	ts_nbus->pwm = pwm;
 
 	/*
@@ -324,7 +310,8 @@ static int ts_nbus_probe(struct platform_device *pdev)
 
 	ret = of_platform_populate(dev->of_node, NULL, NULL, dev);
 	if (ret < 0)
-		return ret;
+		return dev_err_probe(dev, ret,
+				     "failed to populate platform devices on bus\n");
 
 	dev_info(dev, "initialized\n");
 

drivers/clk/ti/apll.c

@@ -376,14 +376,9 @@ static void __init of_omap2_apll_setup(struct device_node *node)
 	}
 	clk_hw->fixed_rate = val;
 
-	if (of_property_read_u32(node, "ti,bit-shift", &val)) {
-		pr_err("%pOFn missing bit-shift\n", node);
-		goto cleanup;
-	}
-
-	clk_hw->enable_bit = val;
-	ad->enable_mask = 0x3 << val;
-	ad->autoidle_mask = 0x3 << val;
+	clk_hw->enable_bit = ti_clk_get_legacy_bit_shift(node);
+	ad->enable_mask = 0x3 << clk_hw->enable_bit;
+	ad->autoidle_mask = 0x3 << clk_hw->enable_bit;
 
 	if (of_property_read_u32(node, "ti,idlest-shift", &val)) {
 		pr_err("%pOFn missing idlest-shift\n", node);

drivers/clk/ti/clk.c

@@ -7,6 +7,7 @@
  * Tero Kristo <t-kristo@ti.com>
  */
 
+#include <linux/cleanup.h>
 #include <linux/clk.h>
 #include <linux/clk-provider.h>
 #include <linux/clkdev.h>
@@ -15,6 +16,7 @@
 #include <linux/of.h>
 #include <linux/of_address.h>
 #include <linux/list.h>
+#include <linux/minmax.h>
 #include <linux/regmap.h>
 #include <linux/string_helpers.h>
 #include <linux/memblock.h>
@@ -114,20 +116,26 @@ int ti_clk_setup_ll_ops(struct ti_clk_ll_ops *ops)
 
 /*
  * Eventually we could standardize to using '_' for clk-*.c files to follow the
- * TRM naming and leave out the tmp name here.
+ * TRM naming.
  */
 static struct device_node *ti_find_clock_provider(struct device_node *from,
 						  const char *name)
 {
+	char *tmp __free(kfree) = NULL;
 	struct device_node *np;
 	bool found = false;
 	const char *n;
-	char *tmp;
+	char *p;
 
 	tmp = kstrdup_and_replace(name, '-', '_', GFP_KERNEL);
 	if (!tmp)
 		return NULL;
 
+	/* Ignore a possible address for the node name */
+	p = strchr(tmp, '@');
+	if (p)
+		*p = '\0';
+
 	/* Node named "clock" with "clock-output-names" */
 	for_each_of_allnodes_from(from, np) {
 		if (of_property_read_string_index(np, "clock-output-names",
@@ -140,7 +148,6 @@ static struct device_node *ti_find_clock_provider(struct device_node *from,
 			break;
 		}
 	}
-	kfree(tmp);
 
 	if (found) {
 		of_node_put(from);
@@ -148,7 +155,7 @@ static struct device_node *ti_find_clock_provider(struct device_node *from,
 	}
 
 	/* Fall back to using old node name base provider name */
-	return of_find_node_by_name(from, name);
+	return of_find_node_by_name(from, tmp);
 }
 
 /**
@@ -301,8 +308,9 @@ int __init ti_clk_retry_init(struct device_node *node, void *user,
 int ti_clk_get_reg_addr(struct device_node *node, int index,
 			struct clk_omap_reg *reg)
 {
-	u32 val;
-	int i;
+	u32 clksel_addr, val;
+	bool is_clksel = false;
+	int i, err;
 
 	for (i = 0; i < CLK_MAX_MEMMAPS; i++) {
 		if (clocks_node_ptr[i] == node->parent)
@@ -318,21 +326,62 @@ int ti_clk_get_reg_addr(struct device_node *node, int index,
 
 	reg->index = i;
 
-	if (of_property_read_u32_index(node, "reg", index, &val)) {
-		if (of_property_read_u32_index(node->parent, "reg",
-					       index, &val)) {
-			pr_err("%pOFn or parent must have reg[%d]!\n",
-			       node, index);
+	if (of_device_is_compatible(node->parent, "ti,clksel")) {
+		err = of_property_read_u32_index(node->parent, "reg", index, &clksel_addr);
+		if (err) {
+			pr_err("%pOFn parent clksel must have reg[%d]!\n", node, index);
 			return -EINVAL;
 		}
+		is_clksel = true;
+	}
+
+	err = of_property_read_u32_index(node, "reg", index, &val);
+	if (err && is_clksel) {
+		/* Legacy clksel with no reg and a possible ti,bit-shift property */
+		reg->offset = clksel_addr;
+		reg->bit = ti_clk_get_legacy_bit_shift(node);
+		reg->ptr = NULL;
+
+		return 0;
+	}
+
+	/* Updated clksel clock with a proper reg property */
+	if (is_clksel) {
+		reg->offset = clksel_addr;
+		reg->bit = val;
+		reg->ptr = NULL;
+		return 0;
 	}
 
+	/* Other clocks that may or may not have ti,bit-shift property  */
 	reg->offset = val;
+	reg->bit = ti_clk_get_legacy_bit_shift(node);
 	reg->ptr = NULL;
 
 	return 0;
 }
 
+/**
+ * ti_clk_get_legacy_bit_shift - get bit shift for a clock register
+ * @node: device node for the clock
+ *
+ * Gets the clock register bit shift using the legacy ti,bit-shift
+ * property. Only needed for legacy clock, and can be eventually
+ * dropped once all the composite clocks use a clksel node with a
+ * proper reg property.
+ */
+int ti_clk_get_legacy_bit_shift(struct device_node *node)
+{
+	int err;
+	u32 val;
+
+	err = of_property_read_u32(node, "ti,bit-shift", &val);
+	if (!err && in_range(val, 0, 32))
+		return val;
+
+	return 0;
+}
+
 void ti_clk_latch(struct clk_omap_reg *reg, s8 shift)
 {
 	u32 latch;

drivers/clk/ti/clock.h

@@ -216,6 +216,7 @@ int ti_clk_parse_divider_data(int *div_table, int num_dividers, int max_div,
 
 int ti_clk_get_reg_addr(struct device_node *node, int index,
 			struct clk_omap_reg *reg);
+int ti_clk_get_legacy_bit_shift(struct device_node *node);
 void ti_dt_clocks_register(struct ti_dt_clk *oclks);
 int ti_clk_retry_init(struct device_node *node, void *user,
 		      ti_of_clk_init_cb_t func);

drivers/clk/ti/divider.c

@@ -477,10 +477,7 @@ static int __init ti_clk_divider_populate(struct device_node *node,
 	if (ret)
 		return ret;
 
-	if (!of_property_read_u32(node, "ti,bit-shift", &val))
-		div->shift = val;
-	else
-		div->shift = 0;
+	div->shift = div->reg.bit;
 
 	if (!of_property_read_u32(node, "ti,latch-bit", &val))
 		div->latch = val;

drivers/clk/ti/gate.c

@@ -132,7 +132,6 @@ static void __init _of_ti_gate_clk_setup(struct device_node *node,
 	struct clk_omap_reg reg;
 	const char *name;
 	u8 enable_bit = 0;
-	u32 val;
 	u32 flags = 0;
 	u8 clk_gate_flags = 0;
 
@@ -140,8 +139,7 @@ static void __init _of_ti_gate_clk_setup(struct device_node *node,
 		if (ti_clk_get_reg_addr(node, 0, &reg))
 			return;
 
-		if (!of_property_read_u32(node, "ti,bit-shift", &val))
-			enable_bit = val;
+		enable_bit = reg.bit;
 	}
 
 	if (of_clk_get_parent_count(node) != 1) {
@@ -170,7 +168,6 @@ _of_ti_composite_gate_clk_setup(struct device_node *node,
 				const struct clk_hw_omap_ops *hw_ops)
 {
 	struct clk_hw_omap *gate;
-	u32 val = 0;
 
 	gate = kzalloc(sizeof(*gate), GFP_KERNEL);
 	if (!gate)
@@ -179,9 +176,7 @@ _of_ti_composite_gate_clk_setup(struct device_node *node,
 	if (ti_clk_get_reg_addr(node, 0, &gate->enable_reg))
 		goto cleanup;
 
-	of_property_read_u32(node, "ti,bit-shift", &val);
-
-	gate->enable_bit = val;
+	gate->enable_bit = gate->enable_reg.bit;
 	gate->ops = hw_ops;
 
 	if (!ti_clk_add_component(node, &gate->hw, CLK_COMPONENT_TYPE_GATE))

drivers/clk/ti/interface.c

@@ -66,13 +66,11 @@ static void __init _of_ti_interface_clk_setup(struct device_node *node,
 	struct clk_omap_reg reg;
 	u8 enable_bit = 0;
 	const char *name;
-	u32 val;
 
 	if (ti_clk_get_reg_addr(node, 0, &reg))
 		return;
 
-	if (!of_property_read_u32(node, "ti,bit-shift", &val))
-		enable_bit = val;
+	enable_bit = reg.bit;
 
 	parent_name = of_clk_get_parent_name(node, 0);
 	if (!parent_name) {

drivers/clk/ti/mux.c

@@ -189,7 +189,7 @@ static void of_mux_clk_setup(struct device_node *node)
 	if (ti_clk_get_reg_addr(node, 0, &reg))
 		goto cleanup;
 
-	of_property_read_u32(node, "ti,bit-shift", &shift);
+	shift = reg.bit;
 
 	of_property_read_u32(node, "ti,latch-bit", &latch);
 
@@ -252,7 +252,6 @@ static void __init of_ti_composite_mux_clk_setup(struct device_node *node)
 {
 	struct clk_omap_mux *mux;
 	unsigned int num_parents;
-	u32 val;
 
 	mux = kzalloc(sizeof(*mux), GFP_KERNEL);
 	if (!mux)
@@ -261,8 +260,7 @@ static void __init of_ti_composite_mux_clk_setup(struct device_node *node)
 	if (ti_clk_get_reg_addr(node, 0, &mux->reg))
 		goto cleanup;
 
-	if (!of_property_read_u32(node, "ti,bit-shift", &val))
-		mux->shift = val;
+	mux->shift = mux->reg.bit;
 
 	if (of_property_read_bool(node, "ti,index-starts-at-one"))
 		mux->flags |= CLK_MUX_INDEX_ONE;

drivers/reset/Kconfig

@@ -66,6 +66,15 @@ config RESET_BRCMSTB_RESCAL
 	  This enables the RESCAL reset controller for SATA, PCIe0, or PCIe1 on
 	  BCM7216.
 
+config RESET_GPIO
+	tristate "GPIO reset controller"
+	help
+	  This enables a generic reset controller for resets attached via
+	  GPIOs.  Typically for OF platforms this driver expects "reset-gpios"
+	  property.
+
+	  If compiled as module, it will be called reset-gpio.
+
 config RESET_HSDK
 	bool "Synopsys HSDK Reset Driver"
 	depends on HAS_IOMEM
@@ -213,7 +222,7 @@ config RESET_SCMI
 
 config RESET_SIMPLE
 	bool "Simple Reset Controller Driver" if COMPILE_TEST || EXPERT
-	default ARCH_ASPEED || ARCH_BCMBCA || ARCH_BITMAIN || ARCH_REALTEK || ARCH_STM32 || (ARCH_INTEL_SOCFPGA && ARM64) || ARCH_SUNXI || ARC
+	default ARCH_ASPEED || ARCH_BCMBCA || ARCH_BITMAIN || ARCH_REALTEK || ARCH_SOPHGO || ARCH_STM32 || (ARCH_INTEL_SOCFPGA && ARM64) || ARCH_SUNXI || ARC
 	depends on HAS_IOMEM
 	help
 	  This enables a simple reset controller driver for reset lines that
@@ -228,6 +237,7 @@ config RESET_SIMPLE
 	   - RCC reset controller in STM32 MCUs
 	   - Allwinner SoCs
 	   - SiFive FU740 SoCs
+	   - Sophgo SoCs
 
 config RESET_SOCFPGA
 	bool "SoCFPGA Reset Driver" if COMPILE_TEST && (!ARM || !ARCH_INTEL_SOCFPGA)

drivers/reset/Makefile

@@ -11,6 +11,7 @@ obj-$(CONFIG_RESET_BCM6345) += reset-bcm6345.o
 obj-$(CONFIG_RESET_BERLIN) += reset-berlin.o
 obj-$(CONFIG_RESET_BRCMSTB) += reset-brcmstb.o
 obj-$(CONFIG_RESET_BRCMSTB_RESCAL) += reset-brcmstb-rescal.o
+obj-$(CONFIG_RESET_GPIO) += reset-gpio.o
 obj-$(CONFIG_RESET_HSDK) += reset-hsdk.o
 obj-$(CONFIG_RESET_IMX7) += reset-imx7.o
 obj-$(CONFIG_RESET_INTEL_GW) += reset-intel-gw.o

drivers/reset/core.c

@@ -5,14 +5,19 @@
  * Copyright 2013 Philipp Zabel, Pengutronix
  */
 #include <linux/atomic.h>
+#include <linux/cleanup.h>
 #include <linux/device.h>
 #include <linux/err.h>
 #include <linux/export.h>
 #include <linux/kernel.h>
 #include <linux/kref.h>
+#include <linux/gpio/driver.h>
+#include <linux/gpio/machine.h>
+#include <linux/idr.h>
 #include <linux/module.h>
 #include <linux/of.h>
 #include <linux/acpi.h>
+#include <linux/platform_device.h>
 #include <linux/reset.h>
 #include <linux/reset-controller.h>
 #include <linux/slab.h>
@@ -23,6 +28,11 @@ static LIST_HEAD(reset_controller_list);
 static DEFINE_MUTEX(reset_lookup_mutex);
 static LIST_HEAD(reset_lookup_list);
 
+/* Protects reset_gpio_lookup_list */
+static DEFINE_MUTEX(reset_gpio_lookup_mutex);
+static LIST_HEAD(reset_gpio_lookup_list);
+static DEFINE_IDA(reset_gpio_ida);
+
 /**
  * struct reset_control - a reset control
  * @rcdev: a pointer to the reset controller device
@@ -63,6 +73,16 @@ struct reset_control_array {
 	struct reset_control *rstc[] __counted_by(num_rstcs);
 };
 
+/**
+ * struct reset_gpio_lookup - lookup key for ad-hoc created reset-gpio devices
+ * @of_args: phandle to the reset controller with all the args like GPIO number
+ * @list: list entry for the reset_gpio_lookup_list
+ */
+struct reset_gpio_lookup {
+	struct of_phandle_args of_args;
+	struct list_head list;
+};
+
 static const char *rcdev_name(struct reset_controller_dev *rcdev)
 {
 	if (rcdev->dev)
@@ -71,6 +91,9 @@ static const char *rcdev_name(struct reset_controller_dev *rcdev)
 	if (rcdev->of_node)
 		return rcdev->of_node->full_name;
 
+	if (rcdev->of_args)
+		return rcdev->of_args->np->full_name;
+
 	return NULL;
 }
 
@@ -99,6 +122,9 @@ static int of_reset_simple_xlate(struct reset_controller_dev *rcdev,
  */
 int reset_controller_register(struct reset_controller_dev *rcdev)
 {
+	if (rcdev->of_node && rcdev->of_args)
+		return -EINVAL;
+
 	if (!rcdev->of_xlate) {
 		rcdev->of_reset_n_cells = 1;
 		rcdev->of_xlate = of_reset_simple_xlate;
@@ -813,12 +839,171 @@ static void __reset_control_put_internal(struct reset_control *rstc)
 	kref_put(&rstc->refcnt, __reset_control_release);
 }
 
+static int __reset_add_reset_gpio_lookup(int id, struct device_node *np,
+					 unsigned int gpio,
+					 unsigned int of_flags)
+{
+	const struct fwnode_handle *fwnode = of_fwnode_handle(np);
+	unsigned int lookup_flags;
+	const char *label_tmp;
+
+	/*
+	 * Later we map GPIO flags between OF and Linux, however not all
+	 * constants from include/dt-bindings/gpio/gpio.h and
+	 * include/linux/gpio/machine.h match each other.
+	 */
+	if (of_flags > GPIO_ACTIVE_LOW) {
+		pr_err("reset-gpio code does not support GPIO flags %u for GPIO %u\n",
+		       of_flags, gpio);
+		return -EINVAL;
+	}
+
+	struct gpio_device *gdev __free(gpio_device_put) = gpio_device_find_by_fwnode(fwnode);
+	if (!gdev)
+		return -EPROBE_DEFER;
+
+	label_tmp = gpio_device_get_label(gdev);
+	if (!label_tmp)
+		return -EINVAL;
+
+	char *label __free(kfree) = kstrdup(label_tmp, GFP_KERNEL);
+	if (!label)
+		return -ENOMEM;
+
+	/* Size: one lookup entry plus sentinel */
+	struct gpiod_lookup_table *lookup __free(kfree) = kzalloc(struct_size(lookup, table, 2),
+								  GFP_KERNEL);
+	if (!lookup)
+		return -ENOMEM;
+
+	lookup->dev_id = kasprintf(GFP_KERNEL, "reset-gpio.%d", id);
+	if (!lookup->dev_id)
+		return -ENOMEM;
+
+	lookup_flags = GPIO_PERSISTENT;
+	lookup_flags |= of_flags & GPIO_ACTIVE_LOW;
+	lookup->table[0] = GPIO_LOOKUP(no_free_ptr(label), gpio, "reset",
+				       lookup_flags);
+
+	/* Not freed on success, because it is persisent subsystem data. */
+	gpiod_add_lookup_table(no_free_ptr(lookup));
+
+	return 0;
+}
+
+/*
+ * @args:	phandle to the GPIO provider with all the args like GPIO number
+ */
+static int __reset_add_reset_gpio_device(const struct of_phandle_args *args)
+{
+	struct reset_gpio_lookup *rgpio_dev;
+	struct platform_device *pdev;
+	int id, ret;
+
+	/*
+	 * Currently only #gpio-cells=2 is supported with the meaning of:
+	 * args[0]: GPIO number
+	 * args[1]: GPIO flags
+	 * TODO: Handle other cases.
+	 */
+	if (args->args_count != 2)
+		return -ENOENT;
+
+	/*
+	 * Registering reset-gpio device might cause immediate
+	 * bind, resulting in its probe() registering new reset controller thus
+	 * taking reset_list_mutex lock via reset_controller_register().
+	 */
+	lockdep_assert_not_held(&reset_list_mutex);
+
+	mutex_lock(&reset_gpio_lookup_mutex);
+
+	list_for_each_entry(rgpio_dev, &reset_gpio_lookup_list, list) {
+		if (args->np == rgpio_dev->of_args.np) {
+			if (of_phandle_args_equal(args, &rgpio_dev->of_args))
+				goto out; /* Already on the list, done */
+		}
+	}
+
+	id = ida_alloc(&reset_gpio_ida, GFP_KERNEL);
+	if (id < 0) {
+		ret = id;
+		goto err_unlock;
+	}
+
+	/* Not freed on success, because it is persisent subsystem data. */
+	rgpio_dev = kzalloc(sizeof(*rgpio_dev), GFP_KERNEL);
+	if (!rgpio_dev) {
+		ret = -ENOMEM;
+		goto err_ida_free;
+	}
+
+	ret = __reset_add_reset_gpio_lookup(id, args->np, args->args[0],
+					    args->args[1]);
+	if (ret < 0)
+		goto err_kfree;
+
+	rgpio_dev->of_args = *args;
+	/*
+	 * We keep the device_node reference, but of_args.np is put at the end
+	 * of __of_reset_control_get(), so get it one more time.
+	 * Hold reference as long as rgpio_dev memory is valid.
+	 */
+	of_node_get(rgpio_dev->of_args.np);
+	pdev = platform_device_register_data(NULL, "reset-gpio", id,
+					     &rgpio_dev->of_args,
+					     sizeof(rgpio_dev->of_args));
+	ret = PTR_ERR_OR_ZERO(pdev);
+	if (ret)
+		goto err_put;
+
+	list_add(&rgpio_dev->list, &reset_gpio_lookup_list);
+
+out:
+	mutex_unlock(&reset_gpio_lookup_mutex);
+
+	return 0;
+
+err_put:
+	of_node_put(rgpio_dev->of_args.np);
+err_kfree:
+	kfree(rgpio_dev);
+err_ida_free:
+	ida_free(&reset_gpio_ida, id);
+err_unlock:
+	mutex_unlock(&reset_gpio_lookup_mutex);
+
+	return ret;
+}
+
+static struct reset_controller_dev *__reset_find_rcdev(const struct of_phandle_args *args,
+						       bool gpio_fallback)
+{
+	struct reset_controller_dev *rcdev;
+
+	lockdep_assert_held(&reset_list_mutex);
+
+	list_for_each_entry(rcdev, &reset_controller_list, list) {
+		if (gpio_fallback) {
+			if (rcdev->of_args && of_phandle_args_equal(args,
+								    rcdev->of_args))
+				return rcdev;
+		} else {
+			if (args->np == rcdev->of_node)
+				return rcdev;
+		}
+	}
+
+	return NULL;
+}
+
 struct reset_control *
 __of_reset_control_get(struct device_node *node, const char *id, int index,
 		       bool shared, bool optional, bool acquired)
 {
+	bool gpio_fallback = false;
 	struct reset_control *rstc;
-	struct reset_controller_dev *r, *rcdev;
+	struct reset_controller_dev *rcdev;
 	struct of_phandle_args args;
 	int rstc_id;
 	int ret;
@@ -839,39 +1024,52 @@ __of_reset_control_get(struct device_node *node, const char *id, int index,
 					 index, &args);
 	if (ret == -EINVAL)
 		return ERR_PTR(ret);
+	if (ret) {
+		if (!IS_ENABLED(CONFIG_RESET_GPIO))
+			return optional ? NULL : ERR_PTR(ret);
+
+		/*
+		 * There can be only one reset-gpio for regular devices, so
+		 * don't bother with the "reset-gpios" phandle index.
+		 */
+		ret = of_parse_phandle_with_args(node, "reset-gpios", "#gpio-cells",
+						 0, &args);
 		if (ret)
 			return optional ? NULL : ERR_PTR(ret);
 
-	mutex_lock(&reset_list_mutex);
-	rcdev = NULL;
-	list_for_each_entry(r, &reset_controller_list, list) {
-		if (args.np == r->of_node) {
-			rcdev = r;
-			break;
+		gpio_fallback = true;
+
+		ret = __reset_add_reset_gpio_device(&args);
+		if (ret) {
+			rstc = ERR_PTR(ret);
+			goto out_put;
 		}
 	}
 
+	mutex_lock(&reset_list_mutex);
+	rcdev = __reset_find_rcdev(&args, gpio_fallback);
 	if (!rcdev) {
 		rstc = ERR_PTR(-EPROBE_DEFER);
-		goto out;
+		goto out_unlock;
 	}
 
 	if (WARN_ON(args.args_count != rcdev->of_reset_n_cells)) {
 		rstc = ERR_PTR(-EINVAL);
-		goto out;
+		goto out_unlock;
 	}
 
 	rstc_id = rcdev->of_xlate(rcdev, &args);
 	if (rstc_id < 0) {
 		rstc = ERR_PTR(rstc_id);
-		goto out;
+		goto out_unlock;
 	}
 
 	/* reset_list_mutex also protects the rcdev's reset_control list */
 	rstc = __reset_control_get_internal(rcdev, rstc_id, shared, acquired);
 
-out:
+out_unlock:
 	mutex_unlock(&reset_list_mutex);
+out_put:
 	of_node_put(args.np);
 
 	return rstc;

drivers/reset/reset-gpio.c

+// SPDX-License-Identifier: GPL-2.0
+
+#include <linux/gpio/consumer.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/reset-controller.h>
+
+struct reset_gpio_priv {
+	struct reset_controller_dev rc;
+	struct gpio_desc *reset;
+};
+
+static inline struct reset_gpio_priv
+*rc_to_reset_gpio(struct reset_controller_dev *rc)
+{
+	return container_of(rc, struct reset_gpio_priv, rc);
+}
+
+static int reset_gpio_assert(struct reset_controller_dev *rc, unsigned long id)
+{
+	struct reset_gpio_priv *priv = rc_to_reset_gpio(rc);
+
+	gpiod_set_value_cansleep(priv->reset, 1);
+
+	return 0;
+}
+
+static int reset_gpio_deassert(struct reset_controller_dev *rc,
+			       unsigned long id)
+{
+	struct reset_gpio_priv *priv = rc_to_reset_gpio(rc);
+
+	gpiod_set_value_cansleep(priv->reset, 0);
+
+	return 0;
+}
+
+static int reset_gpio_status(struct reset_controller_dev *rc, unsigned long id)
+{
+	struct reset_gpio_priv *priv = rc_to_reset_gpio(rc);
+
+	return gpiod_get_value_cansleep(priv->reset);
+}
+
+static const struct reset_control_ops reset_gpio_ops = {
+	.assert = reset_gpio_assert,
+	.deassert = reset_gpio_deassert,
+	.status = reset_gpio_status,
+};
+
+static int reset_gpio_of_xlate(struct reset_controller_dev *rcdev,
+			       const struct of_phandle_args *reset_spec)
+{
+	return reset_spec->args[0];
+}
+
+static void reset_gpio_of_node_put(void *data)
+{
+	of_node_put(data);
+}
+
+static int reset_gpio_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct of_phandle_args *platdata = dev_get_platdata(dev);
+	struct reset_gpio_priv *priv;
+	int ret;
+
+	if (!platdata)
+		return -EINVAL;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, &priv->rc);
+
+	priv->reset = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(priv->reset))
+		return dev_err_probe(dev, PTR_ERR(priv->reset),
+				     "Could not get reset gpios\n");
+
+	priv->rc.ops = &reset_gpio_ops;
+	priv->rc.owner = THIS_MODULE;
+	priv->rc.dev = dev;
+	priv->rc.of_args = platdata;
+	ret = devm_add_action_or_reset(dev, reset_gpio_of_node_put,
+				       priv->rc.of_node);
+	if (ret)
+		return ret;
+
+	/* Cells to match GPIO specifier, but it's not really used */
+	priv->rc.of_reset_n_cells = 2;
+	priv->rc.of_xlate = reset_gpio_of_xlate;
+	priv->rc.nr_resets = 1;
+
+	return devm_reset_controller_register(dev, &priv->rc);
+}
+
+static const struct platform_device_id reset_gpio_ids[] = {
+	{ .name = "reset-gpio", },
+	{}
+};
+MODULE_DEVICE_TABLE(platform, reset_gpio_ids);
+
+static struct platform_driver reset_gpio_driver = {
+	.probe		= reset_gpio_probe,
+	.id_table	= reset_gpio_ids,
+	.driver	= {
+		.name = "reset-gpio",
+	},
+};
+module_platform_driver(reset_gpio_driver);
+
+MODULE_AUTHOR("Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>");
+MODULE_DESCRIPTION("Generic GPIO reset driver");
+MODULE_LICENSE("GPL");

drivers/reset/reset-simple.c

@@ -151,6 +151,8 @@ static const struct of_device_id reset_simple_dt_ids[] = {
 	{ .compatible = "snps,dw-high-reset" },
 	{ .compatible = "snps,dw-low-reset",
 		.data = &reset_simple_active_low },
+	{ .compatible = "sophgo,sg2042-reset",
+		.data = &reset_simple_active_low },
 	{ /* sentinel */ },
 };
 

drivers/soc/fsl/dpio/dpio-service.c

@@ -523,7 +523,7 @@ int dpaa2_io_service_enqueue_multiple_desc_fq(struct dpaa2_io *d,
 	struct qbman_eq_desc *ed;
 	int i, ret;
 
-	ed = kcalloc(sizeof(struct qbman_eq_desc), 32, GFP_KERNEL);
+	ed = kcalloc(32, sizeof(struct qbman_eq_desc), GFP_KERNEL);
 	if (!ed)
 		return -ENOMEM;
 

include/dt-bindings/reset/sophgo,sg2042-reset.h

+/* SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause */
+/*
+ * Copyright (C) 2023 Sophgo Technology Inc. All rights reserved.
+ */
+
+#ifndef __DT_BINDINGS_RESET_SOPHGO_SG2042_H_
+#define __DT_BINDINGS_RESET_SOPHGO_SG2042_H_
+
+#define RST_MAIN_AP			0
+#define RST_RISCV_CPU			1
+#define RST_RISCV_LOW_SPEED_LOGIC	2
+#define RST_RISCV_CMN			3
+#define RST_HSDMA			4
+#define RST_SYSDMA			5
+#define RST_EFUSE0			6
+#define RST_EFUSE1			7
+#define RST_RTC				8
+#define RST_TIMER			9
+#define RST_WDT				10
+#define RST_AHB_ROM0			11
+#define RST_AHB_ROM1			12
+#define RST_I2C0			13
+#define RST_I2C1			14
+#define RST_I2C2			15
+#define RST_I2C3			16
+#define RST_GPIO0			17
+#define RST_GPIO1			18
+#define RST_GPIO2			19
+#define RST_PWM				20
+#define RST_AXI_SRAM0			21
+#define RST_AXI_SRAM1			22
+#define RST_SF0				23
+#define RST_SF1				24
+#define RST_LPC				25
+#define RST_ETH0			26
+#define RST_EMMC			27
+#define RST_SD				28
+#define RST_UART0			29
+#define RST_UART1			30
+#define RST_UART2			31
+#define RST_UART3			32
+#define RST_SPI0			33
+#define RST_SPI1			34
+#define RST_DBG_I2C			35
+#define RST_PCIE0			36
+#define RST_PCIE1			37
+#define RST_DDR0			38
+#define RST_DDR1			39
+#define RST_DDR2			40
+#define RST_DDR3			41
+#define RST_FAU0			42
+#define RST_FAU1			43
+#define RST_FAU2			44
+#define RST_RXU0			45
+#define RST_RXU1			46
+#define RST_RXU2			47
+#define RST_RXU3			48
+#define RST_RXU4			49
+#define RST_RXU5			50
+#define RST_RXU6			51
+#define RST_RXU7			52
+#define RST_RXU8			53
+#define RST_RXU9			54
+#define RST_RXU10			55
+#define RST_RXU11			56
+#define RST_RXU12			57
+#define RST_RXU13			58
+#define RST_RXU14			59
+#define RST_RXU15			60
+#define RST_RXU16			61
+#define RST_RXU17			62
+#define RST_RXU18			63
+#define RST_RXU19			64
+#define RST_RXU20			65
+#define RST_RXU21			66
+#define RST_RXU22			67
+#define RST_RXU23			68
+#define RST_RXU24			69
+#define RST_RXU25			70
+#define RST_RXU26			71
+#define RST_RXU27			72
+#define RST_RXU28			73
+#define RST_RXU29			74
+#define RST_RXU30			75
+#define RST_RXU31			76
+
+#endif /* __DT_BINDINGS_RESET_SOPHGO_SG2042_H_ */

include/linux/clk/ti.h

@@ -13,11 +13,14 @@
 /**
  * struct clk_omap_reg - OMAP register declaration
  * @offset: offset from the master IP module base address
+ * @bit: register bit offset
  * @index: index of the master IP module
+ * @flags: flags
  */
 struct clk_omap_reg {
 	void __iomem *ptr;
 	u16 offset;
+	u8 bit;
 	u8 index;
 	u8 flags;
 };

include/linux/cpufreq.h

@@ -1141,8 +1141,7 @@ static inline int of_perf_domain_get_sharing_cpumask(int pcpu, const char *list_
 		if (ret < 0)
 			continue;
 
-		if (pargs->np == args.np && pargs->args_count == args.args_count &&
-		    !memcmp(pargs->args, args.args, sizeof(args.args[0]) * args.args_count))
+		if (of_phandle_args_equal(pargs, &args))
 			cpumask_set_cpu(cpu, cpumask);
 
 		of_node_put(args.np);

include/linux/of.h

@@ -1083,6 +1083,22 @@ static inline int of_parse_phandle_with_optional_args(const struct device_node *
 					    0, index, out_args);
 }
 
+/**
+ * of_phandle_args_equal() - Compare two of_phandle_args
+ * @a1:		First of_phandle_args to compare
+ * @a2:		Second of_phandle_args to compare
+ *
+ * Return: True if a1 and a2 are the same (same node pointer, same phandle
+ * args), false otherwise.
+ */
+static inline bool of_phandle_args_equal(const struct of_phandle_args *a1,
+					 const struct of_phandle_args *a2)
+{
+	return a1->np == a2->np &&
+	       a1->args_count == a2->args_count &&
+	       !memcmp(a1->args, a2->args, sizeof(a1->args[0]) * a1->args_count);
+}
+
 /**
  * of_property_count_u8_elems - Count the number of u8 elements in a property
  *

include/linux/reset-controller.h

@@ -60,6 +60,9 @@ struct reset_control_lookup {
  * @reset_control_head: head of internal list of requested reset controls
  * @dev: corresponding driver model device struct
  * @of_node: corresponding device tree node as phandle target
+ * @of_args: for reset-gpios controllers: corresponding phandle args with
+ *           of_node and GPIO number complementing of_node; either this or
+ *           of_node should be present
  * @of_reset_n_cells: number of cells in reset line specifiers
  * @of_xlate: translation function to translate from specifier as found in the
  *            device tree to id as given to the reset control ops, defaults
@@ -73,6 +76,7 @@ struct reset_controller_dev {
 	struct list_head reset_control_head;
 	struct device *dev;
 	struct device_node *of_node;
+	const struct of_phandle_args *of_args;
 	int of_reset_n_cells;
 	int (*of_xlate)(struct reset_controller_dev *rcdev,
 			const struct of_phandle_args *reset_spec);