dmaengine: qcom: bam_dma: allow omitting num-{channels,ees}

The bam_dma driver needs to know the number of channels and execution
environments (EEs) at probe time. If we are in full control of the BAM
controller this information can be obtained from the BAM identification
registers (BAM_REVISION/BAM_NUM_PIPES).

When the BAM is "controlled remotely" it is more complicated. The BAM
might not be on at probe time, so reading the registers could fail.
This is why the information must be added to the device tree in this
case, using "num-channels" and "qcom,num-ees".

However, there are also some BAM instances that are initialized by
something else but we still have a clock that allows to turn it on when
needed. This can be set up in the DT with "qcom,controlled-remotely"
and "clocks" and is already supported by the bam_dma driver. Examples
for this are the typical BLSP BAM instances on older SoCs, QPIC BAM
(for NAND) and the crypto BAM on some SoCs.

In this case, there is no need to read "num-channels" and
"qcom,num-ees" from the DT. The BAN can be turned on using the clock
so we can just read it from the BAM registers like in the normal case.

Check for the BAM clock earlier and skip reading "num-channels" and
"qcom,num-ees" if it is present to allow simplifying the DT description
a bit.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Link: https://lore.kernel.org/r/20230518-bamclk-dt-v2-1-a1a857b966ca@gerhold.netSigned-off-by: Vinod Koul <vkoul@kernel.org>

drivers/dma/qcom/bam_dma.c

@@ -1272,7 +1272,15 @@ static int bam_dma_probe(struct platform_device *pdev)
 	bdev->powered_remotely = of_property_read_bool(pdev->dev.of_node,
 						"qcom,powered-remotely");
 
-	if (bdev->controlled_remotely || bdev->powered_remotely) {
+	if (bdev->controlled_remotely || bdev->powered_remotely)
+		bdev->bamclk = devm_clk_get_optional(bdev->dev, "bam_clk");
+	else
+		bdev->bamclk = devm_clk_get(bdev->dev, "bam_clk");
+
+	if (IS_ERR(bdev->bamclk))
+		return PTR_ERR(bdev->bamclk);
+
+	if (!bdev->bamclk) {
 		ret = of_property_read_u32(pdev->dev.of_node, "num-channels",
 					   &bdev->num_channels);
 		if (ret)
@@ -1284,14 +1292,6 @@ static int bam_dma_probe(struct platform_device *pdev)
 			dev_err(bdev->dev, "num-ees unspecified in dt\n");
 	}
 
-	if (bdev->controlled_remotely || bdev->powered_remotely)
-		bdev->bamclk = devm_clk_get_optional(bdev->dev, "bam_clk");
-	else
-		bdev->bamclk = devm_clk_get(bdev->dev, "bam_clk");
-
-	if (IS_ERR(bdev->bamclk))
-		return PTR_ERR(bdev->bamclk);
-
 	ret = clk_prepare_enable(bdev->bamclk);
 	if (ret) {
 		dev_err(bdev->dev, "failed to prepare/enable clock\n");