Merge tag 'char-misc-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc

Pull char/misc driver fixes from Greg KH:
 "Here are a number of small char/misc/whatever driver fixes. They
  include:

   - IIO driver fixes for some reported problems

   - nvmem driver fixes

   - fpga driver fixes

   - debugfs memory leak fix in the hv_balloon and irqdomain code
     (irqdomain change was acked by the maintainer)

  All have been in linux-next with no reported problems"

* tag 'char-misc-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (33 commits)
  kernel/irq/irqdomain.c: fix memory leak with using debugfs_lookup()
  HV: hv_balloon: fix memory leak with using debugfs_lookup()
  nvmem: qcom-spmi-sdam: fix module autoloading
  nvmem: core: fix return value
  nvmem: core: fix cell removal on error
  nvmem: core: fix device node refcounting
  nvmem: core: fix registration vs use race
  nvmem: core: fix cleanup after dev_set_name()
  nvmem: core: remove nvmem_config wp_gpio
  nvmem: core: initialise nvmem->id early
  nvmem: sunxi_sid: Always use 32-bit MMIO reads
  nvmem: brcm_nvram: Add check for kzalloc
  iio: imu: fxos8700: fix MAGN sensor scale and unit
  iio: imu: fxos8700: remove definition FXOS8700_CTRL_ODR_MIN
  iio: imu: fxos8700: fix failed initialization ODR mode assignment
  iio: imu: fxos8700: fix incorrect ODR mode readback
  iio: light: cm32181: Fix PM support on system with 2 I2C resources
  iio: hid: fix the retval in gyro_3d_capture_sample
  iio: hid: fix the retval in accel_3d_capture_sample
  iio: imu: st_lsm6dsx: fix build when CONFIG_IIO_TRIGGERED_BUFFER=m
  ...

drivers/fpga/intel-m10-bmc-sec-update.c

@@ -574,20 +574,27 @@ static int m10bmc_sec_probe(struct platform_device *pdev)
 	len = scnprintf(buf, SEC_UPDATE_LEN_MAX, "secure-update%d",
 			sec->fw_name_id);
 	sec->fw_name = kmemdup_nul(buf, len, GFP_KERNEL);
-	if (!sec->fw_name)
-		return -ENOMEM;
+	if (!sec->fw_name) {
+		ret = -ENOMEM;
+		goto fw_name_fail;
+	}
 
 	fwl = firmware_upload_register(THIS_MODULE, sec->dev, sec->fw_name,
 				       &m10bmc_ops, sec);
 	if (IS_ERR(fwl)) {
 		dev_err(sec->dev, "Firmware Upload driver failed to start\n");
-		kfree(sec->fw_name);
-		xa_erase(&fw_upload_xa, sec->fw_name_id);
-		return PTR_ERR(fwl);
+		ret = PTR_ERR(fwl);
+		goto fw_uploader_fail;
 	}
 
 	sec->fwl = fwl;
 	return 0;
+
+fw_uploader_fail:
+	kfree(sec->fw_name);
+fw_name_fail:
+	xa_erase(&fw_upload_xa, sec->fw_name_id);
+	return ret;
 }
 
 static int m10bmc_sec_remove(struct platform_device *pdev)

drivers/fpga/stratix10-soc.c

@@ -213,9 +213,9 @@ static int s10_ops_write_init(struct fpga_manager *mgr,
 	/* Allocate buffers from the service layer's pool. */
 	for (i = 0; i < NUM_SVC_BUFS; i++) {
 		kbuf = stratix10_svc_allocate_memory(priv->chan, SVC_BUF_SIZE);
-		if (!kbuf) {
+		if (IS_ERR(kbuf)) {
 			s10_free_buffers(mgr);
-			ret = -ENOMEM;
+			ret = PTR_ERR(kbuf);
 			goto init_done;
 		}
 

drivers/hv/hv_balloon.c

@@ -1963,7 +1963,7 @@ static void  hv_balloon_debugfs_init(struct hv_dynmem_device *b)
 
 static void  hv_balloon_debugfs_exit(struct hv_dynmem_device *b)
 {
-	debugfs_remove(debugfs_lookup("hv-balloon", NULL));
+	debugfs_lookup_and_remove("hv-balloon", NULL);
 }
 
 #else

drivers/iio/accel/hid-sensor-accel-3d.c

@@ -280,6 +280,7 @@ static int accel_3d_capture_sample(struct hid_sensor_hub_device *hsdev,
 			hid_sensor_convert_timestamp(
 					&accel_state->common_attributes,
 					*(int64_t *)raw_data);
+		ret = 0;
 	break;
 	default:
 		break;

drivers/iio/adc/berlin2-adc.c

@@ -298,8 +298,10 @@ static int berlin2_adc_probe(struct platform_device *pdev)
 	int ret;
 
 	indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*priv));
-	if (!indio_dev)
+	if (!indio_dev) {
+		of_node_put(parent_np);
 		return -ENOMEM;
+	}
 
 	priv = iio_priv(indio_dev);
 

drivers/iio/adc/imx8qxp-adc.c

@@ -86,6 +86,8 @@
 
 #define IMX8QXP_ADC_TIMEOUT		msecs_to_jiffies(100)
 
+#define IMX8QXP_ADC_MAX_FIFO_SIZE		16
+
 struct imx8qxp_adc {
 	struct device *dev;
 	void __iomem *regs;
@@ -95,6 +97,7 @@ struct imx8qxp_adc {
 	/* Serialise ADC channel reads */
 	struct mutex lock;
 	struct completion completion;
+	u32 fifo[IMX8QXP_ADC_MAX_FIFO_SIZE];
 };
 
 #define IMX8QXP_ADC_CHAN(_idx) {				\
@@ -238,8 +241,7 @@ static int imx8qxp_adc_read_raw(struct iio_dev *indio_dev,
 			return ret;
 		}
 
-		*val = FIELD_GET(IMX8QXP_ADC_RESFIFO_VAL_MASK,
-				 readl(adc->regs + IMX8QXP_ADR_ADC_RESFIFO));
+		*val = adc->fifo[0];
 
 		mutex_unlock(&adc->lock);
 		return IIO_VAL_INT;
@@ -265,10 +267,15 @@ static irqreturn_t imx8qxp_adc_isr(int irq, void *dev_id)
 {
 	struct imx8qxp_adc *adc = dev_id;
 	u32 fifo_count;
+	int i;
 
 	fifo_count = FIELD_GET(IMX8QXP_ADC_FCTRL_FCOUNT_MASK,
 			       readl(adc->regs + IMX8QXP_ADR_ADC_FCTRL));
 
+	for (i = 0; i < fifo_count; i++)
+		adc->fifo[i] = FIELD_GET(IMX8QXP_ADC_RESFIFO_VAL_MASK,
+				readl_relaxed(adc->regs + IMX8QXP_ADR_ADC_RESFIFO));
+
 	if (fifo_count)
 		complete(&adc->completion);
 

drivers/iio/adc/stm32-dfsdm-adc.c

@@ -1520,6 +1520,7 @@ static const struct of_device_id stm32_dfsdm_adc_match[] = {
 	},
 	{}
 };
+MODULE_DEVICE_TABLE(of, stm32_dfsdm_adc_match);
 
 static int stm32_dfsdm_adc_probe(struct platform_device *pdev)
 {

drivers/iio/adc/twl6030-gpadc.c

@@ -57,6 +57,18 @@
 #define TWL6030_GPADCS				BIT(1)
 #define TWL6030_GPADCR				BIT(0)
 
+#define USB_VBUS_CTRL_SET			0x04
+#define USB_ID_CTRL_SET				0x06
+
+#define TWL6030_MISC1				0xE4
+#define VBUS_MEAS				0x01
+#define ID_MEAS					0x01
+
+#define VAC_MEAS                0x04
+#define VBAT_MEAS               0x02
+#define BB_MEAS                 0x01
+
+
 /**
  * struct twl6030_chnl_calib - channel calibration
  * @gain:		slope coefficient for ideal curve
@@ -927,6 +939,26 @@ static int twl6030_gpadc_probe(struct platform_device *pdev)
 		return ret;
 	}
 
+	ret = twl_i2c_write_u8(TWL_MODULE_USB, VBUS_MEAS, USB_VBUS_CTRL_SET);
+	if (ret < 0) {
+		dev_err(dev, "failed to wire up inputs\n");
+		return ret;
+	}
+
+	ret = twl_i2c_write_u8(TWL_MODULE_USB, ID_MEAS, USB_ID_CTRL_SET);
+	if (ret < 0) {
+		dev_err(dev, "failed to wire up inputs\n");
+		return ret;
+	}
+
+	ret = twl_i2c_write_u8(TWL6030_MODULE_ID0,
+				VBAT_MEAS | BB_MEAS | VAC_MEAS,
+				TWL6030_MISC1);
+	if (ret < 0) {
+		dev_err(dev, "failed to wire up inputs\n");
+		return ret;
+	}
+
 	indio_dev->name = DRIVER_NAME;
 	indio_dev->info = &twl6030_gpadc_iio_info;
 	indio_dev->modes = INDIO_DIRECT_MODE;

drivers/iio/adc/xilinx-ams.c

@@ -1329,7 +1329,7 @@ static int ams_parse_firmware(struct iio_dev *indio_dev)
 
 	dev_channels = devm_krealloc(dev, ams_channels, dev_size, GFP_KERNEL);
 	if (!dev_channels)
-		ret = -ENOMEM;
+		return -ENOMEM;
 
 	indio_dev->channels = dev_channels;
 	indio_dev->num_channels = num_channels;

drivers/iio/gyro/hid-sensor-gyro-3d.c

@@ -231,6 +231,7 @@ static int gyro_3d_capture_sample(struct hid_sensor_hub_device *hsdev,
 		gyro_state->timestamp =
 			hid_sensor_convert_timestamp(&gyro_state->common_attributes,
 						     *(s64 *)raw_data);
+		ret = 0;
 	break;
 	default:
 		break;

drivers/iio/imu/fxos8700_core.c

@@ -10,6 +10,7 @@
 #include <linux/regmap.h>
 #include <linux/acpi.h>
 #include <linux/bitops.h>
+#include <linux/bitfield.h>
 
 #include <linux/iio/iio.h>
 #include <linux/iio/sysfs.h>
@@ -144,9 +145,8 @@
 #define FXOS8700_NVM_DATA_BNK0      0xa7
 
 /* Bit definitions for FXOS8700_CTRL_REG1 */
-#define FXOS8700_CTRL_ODR_MSK       0x38
 #define FXOS8700_CTRL_ODR_MAX       0x00
-#define FXOS8700_CTRL_ODR_MIN       GENMASK(4, 3)
+#define FXOS8700_CTRL_ODR_MSK       GENMASK(5, 3)
 
 /* Bit definitions for FXOS8700_M_CTRL_REG1 */
 #define FXOS8700_HMS_MASK           GENMASK(1, 0)
@@ -320,7 +320,7 @@ static enum fxos8700_sensor fxos8700_to_sensor(enum iio_chan_type iio_type)
 	switch (iio_type) {
 	case IIO_ACCEL:
 		return FXOS8700_ACCEL;
-	case IIO_ANGL_VEL:
+	case IIO_MAGN:
 		return FXOS8700_MAGN;
 	default:
 		return -EINVAL;
@@ -345,15 +345,35 @@ static int fxos8700_set_active_mode(struct fxos8700_data *data,
 static int fxos8700_set_scale(struct fxos8700_data *data,
 			      enum fxos8700_sensor t, int uscale)
 {
-	int i;
+	int i, ret, val;
+	bool active_mode;
 	static const int scale_num = ARRAY_SIZE(fxos8700_accel_scale);
 	struct device *dev = regmap_get_device(data->regmap);
 
 	if (t == FXOS8700_MAGN) {
-		dev_err(dev, "Magnetometer scale is locked at 1200uT\n");
+		dev_err(dev, "Magnetometer scale is locked at 0.001Gs\n");
 		return -EINVAL;
 	}
 
+	/*
+	 * When device is in active mode, it failed to set an ACCEL
+	 * full-scale range(2g/4g/8g) in FXOS8700_XYZ_DATA_CFG.
+	 * This is not align with the datasheet, but it is a fxos8700
+	 * chip behavier. Set the device in standby mode before setting
+	 * an ACCEL full-scale range.
+	 */
+	ret = regmap_read(data->regmap, FXOS8700_CTRL_REG1, &val);
+	if (ret)
+		return ret;
+
+	active_mode = val & FXOS8700_ACTIVE;
+	if (active_mode) {
+		ret = regmap_write(data->regmap, FXOS8700_CTRL_REG1,
+				   val & ~FXOS8700_ACTIVE);
+		if (ret)
+			return ret;
+	}
+
 	for (i = 0; i < scale_num; i++)
 		if (fxos8700_accel_scale[i].uscale == uscale)
 			break;
@@ -361,8 +381,12 @@ static int fxos8700_set_scale(struct fxos8700_data *data,
 	if (i == scale_num)
 		return -EINVAL;
 
-	return regmap_write(data->regmap, FXOS8700_XYZ_DATA_CFG,
+	ret = regmap_write(data->regmap, FXOS8700_XYZ_DATA_CFG,
 			    fxos8700_accel_scale[i].bits);
+	if (ret)
+		return ret;
+	return regmap_write(data->regmap, FXOS8700_CTRL_REG1,
+				  active_mode);
 }
 
 static int fxos8700_get_scale(struct fxos8700_data *data,
@@ -372,7 +396,7 @@ static int fxos8700_get_scale(struct fxos8700_data *data,
 	static const int scale_num = ARRAY_SIZE(fxos8700_accel_scale);
 
 	if (t == FXOS8700_MAGN) {
-		*uscale = 1200; /* Magnetometer is locked at 1200uT */
+		*uscale = 1000; /* Magnetometer is locked at 0.001Gs */
 		return 0;
 	}
 
@@ -394,22 +418,61 @@ static int fxos8700_get_data(struct fxos8700_data *data, int chan_type,
 			     int axis, int *val)
 {
 	u8 base, reg;
+	s16 tmp;
 	int ret;
-	enum fxos8700_sensor type = fxos8700_to_sensor(chan_type);
 
-	base = type ? FXOS8700_OUT_X_MSB : FXOS8700_M_OUT_X_MSB;
+	/*
+	 * Different register base addresses varies with channel types.
+	 * This bug hasn't been noticed before because using an enum is
+	 * really hard to read. Use an a switch statement to take over that.
+	 */
+	switch (chan_type) {
+	case IIO_ACCEL:
+		base = FXOS8700_OUT_X_MSB;
+		break;
+	case IIO_MAGN:
+		base = FXOS8700_M_OUT_X_MSB;
+		break;
+	default:
+		return -EINVAL;
+	}
 
 	/* Block read 6 bytes of device output registers to avoid data loss */
 	ret = regmap_bulk_read(data->regmap, base, data->buf,
-			       FXOS8700_DATA_BUF_SIZE);
+			       sizeof(data->buf));
 	if (ret)
 		return ret;
 
 	/* Convert axis to buffer index */
 	reg = axis - IIO_MOD_X;
 
+	/*
+	 * Convert to native endianness. The accel data and magn data
+	 * are signed, so a forced type conversion is needed.
+	 */
+	tmp = be16_to_cpu(data->buf[reg]);
+
+	/*
+	 * ACCEL output data registers contain the X-axis, Y-axis, and Z-axis
+	 * 14-bit left-justified sample data and MAGN output data registers
+	 * contain the X-axis, Y-axis, and Z-axis 16-bit sample data. Apply
+	 * a signed 2 bits right shift to the readback raw data from ACCEL
+	 * output data register and keep that from MAGN sensor as the origin.
+	 * Value should be extended to 32 bit.
+	 */
+	switch (chan_type) {
+	case IIO_ACCEL:
+		tmp = tmp >> 2;
+		break;
+	case IIO_MAGN:
+		/* Nothing to do */
+		break;
+	default:
+		return -EINVAL;
+	}
+
 	/* Convert to native endianness */
-	*val = sign_extend32(be16_to_cpu(data->buf[reg]), 15);
+	*val = sign_extend32(tmp, 15);
 
 	return 0;
 }
@@ -445,10 +508,9 @@ static int fxos8700_set_odr(struct fxos8700_data *data, enum fxos8700_sensor t,
 	if (i >= odr_num)
 		return -EINVAL;
 
-	return regmap_update_bits(data->regmap,
-				  FXOS8700_CTRL_REG1,
-				  FXOS8700_CTRL_ODR_MSK + FXOS8700_ACTIVE,
-				  fxos8700_odr[i].bits << 3 | active_mode);
+	val &= ~FXOS8700_CTRL_ODR_MSK;
+	val |= FIELD_PREP(FXOS8700_CTRL_ODR_MSK, fxos8700_odr[i].bits) | FXOS8700_ACTIVE;
+	return regmap_write(data->regmap, FXOS8700_CTRL_REG1, val);
 }
 
 static int fxos8700_get_odr(struct fxos8700_data *data, enum fxos8700_sensor t,
@@ -461,7 +523,7 @@ static int fxos8700_get_odr(struct fxos8700_data *data, enum fxos8700_sensor t,
 	if (ret)
 		return ret;
 
-	val &= FXOS8700_CTRL_ODR_MSK;
+	val = FIELD_GET(FXOS8700_CTRL_ODR_MSK, val);
 
 	for (i = 0; i < odr_num; i++)
 		if (val == fxos8700_odr[i].bits)
@@ -526,7 +588,7 @@ static IIO_CONST_ATTR(in_accel_sampling_frequency_available,
 static IIO_CONST_ATTR(in_magn_sampling_frequency_available,
 		      "1.5625 6.25 12.5 50 100 200 400 800");
 static IIO_CONST_ATTR(in_accel_scale_available, "0.000244 0.000488 0.000976");
-static IIO_CONST_ATTR(in_magn_scale_available, "0.000001200");
+static IIO_CONST_ATTR(in_magn_scale_available, "0.001000");
 
 static struct attribute *fxos8700_attrs[] = {
 	&iio_const_attr_in_accel_sampling_frequency_available.dev_attr.attr,
@@ -592,14 +654,19 @@ static int fxos8700_chip_init(struct fxos8700_data *data, bool use_spi)
 	if (ret)
 		return ret;
 
-	/* Max ODR (800Hz individual or 400Hz hybrid), active mode */
-	ret = regmap_write(data->regmap, FXOS8700_CTRL_REG1,
-			   FXOS8700_CTRL_ODR_MAX | FXOS8700_ACTIVE);
+	/*
+	 * Set max full-scale range (+/-8G) for ACCEL sensor in chip
+	 * initialization then activate the device.
+	 */
+	ret = regmap_write(data->regmap, FXOS8700_XYZ_DATA_CFG, MODE_8G);
 	if (ret)
 		return ret;
 
-	/* Set for max full-scale range (+/-8G) */
-	return regmap_write(data->regmap, FXOS8700_XYZ_DATA_CFG, MODE_8G);
+	/* Max ODR (800Hz individual or 400Hz hybrid), active mode */
+	return regmap_update_bits(data->regmap, FXOS8700_CTRL_REG1,
+				FXOS8700_CTRL_ODR_MSK | FXOS8700_ACTIVE,
+				FIELD_PREP(FXOS8700_CTRL_ODR_MSK, FXOS8700_CTRL_ODR_MAX) |
+				FXOS8700_ACTIVE);
 }
 
 static void fxos8700_chip_uninit(void *data)

drivers/iio/imu/st_lsm6dsx/Kconfig

@@ -4,6 +4,7 @@ config IIO_ST_LSM6DSX
 	tristate "ST_LSM6DSx driver for STM 6-axis IMU MEMS sensors"
 	depends on (I2C || SPI || I3C)
 	select IIO_BUFFER
+	select IIO_TRIGGERED_BUFFER
 	select IIO_KFIFO_BUF
 	select IIO_ST_LSM6DSX_I2C if (I2C)
 	select IIO_ST_LSM6DSX_SPI if (SPI_MASTER)

drivers/iio/light/cm32181.c

@@ -440,6 +440,8 @@ static int cm32181_probe(struct i2c_client *client)
 	if (!indio_dev)
 		return -ENOMEM;
 
+	i2c_set_clientdata(client, indio_dev);
+
 	/*
 	 * Some ACPI systems list 2 I2C resources for the CM3218 sensor, the
 	 * SMBus Alert Response Address (ARA, 0x0c) and the actual I2C address.
@@ -460,8 +462,6 @@ static int cm32181_probe(struct i2c_client *client)
 			return PTR_ERR(client);
 	}
 
-	i2c_set_clientdata(client, indio_dev);
-
 	cm32181 = iio_priv(indio_dev);
 	cm32181->client = client;
 	cm32181->dev = dev;
@@ -490,7 +490,8 @@ static int cm32181_probe(struct i2c_client *client)
 
 static int cm32181_suspend(struct device *dev)
 {
-	struct i2c_client *client = to_i2c_client(dev);
+	struct cm32181_chip *cm32181 = iio_priv(dev_get_drvdata(dev));
+	struct i2c_client *client = cm32181->client;
 
 	return i2c_smbus_write_word_data(client, CM32181_REG_ADDR_CMD,
 					 CM32181_CMD_ALS_DISABLE);
@@ -498,8 +499,8 @@ static int cm32181_suspend(struct device *dev)
 
 static int cm32181_resume(struct device *dev)
 {
-	struct i2c_client *client = to_i2c_client(dev);
 	struct cm32181_chip *cm32181 = iio_priv(dev_get_drvdata(dev));
+	struct i2c_client *client = cm32181->client;
 
 	return i2c_smbus_write_word_data(client, CM32181_REG_ADDR_CMD,
 					 cm32181->conf_regs[CM32181_REG_ADDR_CMD]);

drivers/nvmem/brcm_nvram.c

@@ -98,6 +98,9 @@ static int brcm_nvram_parse(struct brcm_nvram *priv)
 	len = le32_to_cpu(header.len);
 
 	data = kzalloc(len, GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
 	memcpy_fromio(data, priv->base, len);
 	data[len - 1] = '\0';
 

drivers/nvmem/core.c

@@ -770,31 +770,32 @@ struct nvmem_device *nvmem_register(const struct nvmem_config *config)
 		return ERR_PTR(rval);
 	}
 
-	if (config->wp_gpio)
-		nvmem->wp_gpio = config->wp_gpio;
-	else if (!config->ignore_wp)
+	nvmem->id = rval;
+
+	nvmem->dev.type = &nvmem_provider_type;
+	nvmem->dev.bus = &nvmem_bus_type;
+	nvmem->dev.parent = config->dev;
+
+	device_initialize(&nvmem->dev);
+
+	if (!config->ignore_wp)
 		nvmem->wp_gpio = gpiod_get_optional(config->dev, "wp",
 						    GPIOD_OUT_HIGH);
 	if (IS_ERR(nvmem->wp_gpio)) {
-		ida_free(&nvmem_ida, nvmem->id);
 		rval = PTR_ERR(nvmem->wp_gpio);
-		kfree(nvmem);
-		return ERR_PTR(rval);
+		nvmem->wp_gpio = NULL;
+		goto err_put_device;
 	}
 
 	kref_init(&nvmem->refcnt);
 	INIT_LIST_HEAD(&nvmem->cells);
 
-	nvmem->id = rval;
 	nvmem->owner = config->owner;
 	if (!nvmem->owner && config->dev->driver)
 		nvmem->owner = config->dev->driver->owner;
 	nvmem->stride = config->stride ?: 1;
 	nvmem->word_size = config->word_size ?: 1;
 	nvmem->size = config->size;
-	nvmem->dev.type = &nvmem_provider_type;
-	nvmem->dev.bus = &nvmem_bus_type;
-	nvmem->dev.parent = config->dev;
 	nvmem->root_only = config->root_only;
 	nvmem->priv = config->priv;
 	nvmem->type = config->type;
@@ -822,11 +823,8 @@ struct nvmem_device *nvmem_register(const struct nvmem_config *config)
 		break;
 	}
 
-	if (rval) {
-		ida_free(&nvmem_ida, nvmem->id);
-		kfree(nvmem);
-		return ERR_PTR(rval);
-	}
+	if (rval)
+		goto err_put_device;
 
 	nvmem->read_only = device_property_present(config->dev, "read-only") ||
 			   config->read_only || !nvmem->reg_write;
@@ -835,28 +833,22 @@ struct nvmem_device *nvmem_register(const struct nvmem_config *config)
 	nvmem->dev.groups = nvmem_dev_groups;
 #endif
 
-	dev_dbg(&nvmem->dev, "Registering nvmem device %s\n", config->name);
-
-	rval = device_register(&nvmem->dev);
-	if (rval)
-		goto err_put_device;
-
 	if (nvmem->nkeepout) {
 		rval = nvmem_validate_keepouts(nvmem);
 		if (rval)
-			goto err_device_del;
+			goto err_put_device;
 	}
 
 	if (config->compat) {
 		rval = nvmem_sysfs_setup_compat(nvmem, config);
 		if (rval)
-			goto err_device_del;
+			goto err_put_device;
 	}
 
 	if (config->cells) {
 		rval = nvmem_add_cells(nvmem, config->cells, config->ncells);
 		if (rval)
-			goto err_teardown_compat;
+			goto err_remove_cells;
 	}
 
 	rval = nvmem_add_cells_from_table(nvmem);
@@ -867,17 +859,20 @@ struct nvmem_device *nvmem_register(const struct nvmem_config *config)
 	if (rval)
 		goto err_remove_cells;
 
+	dev_dbg(&nvmem->dev, "Registering nvmem device %s\n", config->name);
+
+	rval = device_add(&nvmem->dev);
+	if (rval)
+		goto err_remove_cells;
+
 	blocking_notifier_call_chain(&nvmem_notifier, NVMEM_ADD, nvmem);
 
 	return nvmem;
 
 err_remove_cells:
 	nvmem_device_remove_all_cells(nvmem);
-err_teardown_compat:
 	if (config->compat)
 		nvmem_sysfs_remove_compat(nvmem, config);
-err_device_del:
-	device_del(&nvmem->dev);
 err_put_device:
 	put_device(&nvmem->dev);
 
@@ -1242,16 +1237,21 @@ struct nvmem_cell *of_nvmem_cell_get(struct device_node *np, const char *id)
 	if (!cell_np)
 		return ERR_PTR(-ENOENT);
 
-	nvmem_np = of_get_next_parent(cell_np);
-	if (!nvmem_np)
+	nvmem_np = of_get_parent(cell_np);
+	if (!nvmem_np) {
+		of_node_put(cell_np);
 		return ERR_PTR(-EINVAL);
+	}
 
 	nvmem = __nvmem_device_get(nvmem_np, device_match_of_node);
 	of_node_put(nvmem_np);
-	if (IS_ERR(nvmem))
+	if (IS_ERR(nvmem)) {
+		of_node_put(cell_np);
 		return ERR_CAST(nvmem);
+	}
 
 	cell_entry = nvmem_find_cell_entry_by_node(nvmem, cell_np);
+	of_node_put(cell_np);
 	if (!cell_entry) {
 		__nvmem_device_put(nvmem);
 		return ERR_PTR(-ENOENT);

drivers/nvmem/qcom-spmi-sdam.c

@@ -166,6 +166,7 @@ static const struct of_device_id sdam_match_table[] = {
 	{ .compatible = "qcom,spmi-sdam" },
 	{},
 };
+MODULE_DEVICE_TABLE(of, sdam_match_table);
 
 static struct platform_driver sdam_driver = {
 	.driver = {

drivers/nvmem/sunxi_sid.c

@@ -41,8 +41,21 @@ static int sunxi_sid_read(void *context, unsigned int offset,
 			  void *val, size_t bytes)
 {
 	struct sunxi_sid *sid = context;
+	u32 word;
+
+	/* .stride = 4 so offset is guaranteed to be aligned */
+	__ioread32_copy(val, sid->base + sid->value_offset + offset, bytes / 4);
 
-	memcpy_fromio(val, sid->base + sid->value_offset + offset, bytes);
+	val += round_down(bytes, 4);
+	offset += round_down(bytes, 4);
+	bytes = bytes % 4;
+
+	if (!bytes)
+		return 0;
+
+	/* Handle any trailing bytes */
+	word = readl_relaxed(sid->base + sid->value_offset + offset);
+	memcpy(val, &word, bytes);
 
 	return 0;
 }

include/linux/nvmem-provider.h

@@ -70,7 +70,6 @@ struct nvmem_keepout {
  * @word_size:	Minimum read/write access granularity.
  * @stride:	Minimum read/write access stride.
  * @priv:	User context passed to read/write callbacks.
- * @wp-gpio:	Write protect pin
  * @ignore_wp:  Write Protect pin is managed by the provider.
  *
  * Note: A default "nvmem<id>" name will be assigned to the device if
@@ -85,7 +84,6 @@ struct nvmem_config {
 	const char		*name;
 	int			id;
 	struct module		*owner;
-	struct gpio_desc	*wp_gpio;
 	const struct nvmem_cell_info	*cells;
 	int			ncells;
 	const struct nvmem_keepout *keepout;

kernel/irq/irqdomain.c

@@ -1915,7 +1915,7 @@ static void debugfs_add_domain_dir(struct irq_domain *d)
 
 static void debugfs_remove_domain_dir(struct irq_domain *d)
 {
-	debugfs_remove(debugfs_lookup(d->name, domain_dir));
+	debugfs_lookup_and_remove(d->name, domain_dir);
 }
 
 void __init irq_domain_debugfs_init(struct dentry *root)