Merge branch 'ib-extcon-mfd-4.16' into extcon-next

drivers/extcon/extcon-axp288.c

@@ -24,8 +24,6 @@
 #include <linux/notifier.h>
 #include <linux/extcon-provider.h>
 #include <linux/regmap.h>
-#include <linux/gpio.h>
-#include <linux/gpio/consumer.h>
 #include <linux/mfd/axp20x.h>
 
 /* Power source status register */
@@ -79,11 +77,6 @@ enum axp288_extcon_reg {
 	AXP288_BC_DET_STAT_REG		= 0x2f,
 };
 
-enum axp288_mux_select {
-	EXTCON_GPIO_MUX_SEL_PMIC = 0,
-	EXTCON_GPIO_MUX_SEL_SOC,
-};
-
 enum axp288_extcon_irq {
 	VBUS_FALLING_IRQ = 0,
 	VBUS_RISING_IRQ,
@@ -104,10 +97,8 @@ struct axp288_extcon_info {
 	struct device *dev;
 	struct regmap *regmap;
 	struct regmap_irq_chip_data *regmap_irqc;
-	struct gpio_desc *gpio_mux_cntl;
 	int irq[EXTCON_IRQ_END];
 	struct extcon_dev *edev;
-	struct notifier_block extcon_nb;
 	unsigned int previous_cable;
 };
 
@@ -197,15 +188,6 @@ static int axp288_handle_chrg_det_event(struct axp288_extcon_info *info)
 	}
 
 no_vbus:
-	/*
-	 * If VBUS is absent Connect D+/D- lines to PMIC for BC
-	 * detection. Else connect them to SOC for USB communication.
-	 */
-	if (info->gpio_mux_cntl)
-		gpiod_set_value(info->gpio_mux_cntl,
-			vbus_attach ? EXTCON_GPIO_MUX_SEL_SOC
-					: EXTCON_GPIO_MUX_SEL_PMIC);
-
 	extcon_set_state_sync(info->edev, info->previous_cable, false);
 	if (info->previous_cable == EXTCON_CHG_USB_SDP)
 		extcon_set_state_sync(info->edev, EXTCON_USB, false);
@@ -253,8 +235,7 @@ static int axp288_extcon_probe(struct platform_device *pdev)
 {
 	struct axp288_extcon_info *info;
 	struct axp20x_dev *axp20x = dev_get_drvdata(pdev->dev.parent);
-	struct axp288_extcon_pdata *pdata = pdev->dev.platform_data;
-	int ret, i, pirq, gpio;
+	int ret, i, pirq;
 
 	info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL);
 	if (!info)
@@ -264,8 +245,6 @@ static int axp288_extcon_probe(struct platform_device *pdev)
 	info->regmap = axp20x->regmap;
 	info->regmap_irqc = axp20x->regmap_irqc;
 	info->previous_cable = EXTCON_NONE;
-	if (pdata)
-		info->gpio_mux_cntl = pdata->gpio_mux_cntl;
 
 	platform_set_drvdata(pdev, info);
 
@@ -286,21 +265,11 @@ static int axp288_extcon_probe(struct platform_device *pdev)
 		return ret;
 	}
 
-	/* Set up gpio control for USB Mux */
-	if (info->gpio_mux_cntl) {
-		gpio = desc_to_gpio(info->gpio_mux_cntl);
-		ret = devm_gpio_request(&pdev->dev, gpio, "USB_MUX");
-		if (ret < 0) {
-			dev_err(&pdev->dev,
-				"failed to request the gpio=%d\n", gpio);
-			return ret;
-		}
-		gpiod_direction_output(info->gpio_mux_cntl,
-						EXTCON_GPIO_MUX_SEL_PMIC);
-	}
-
 	for (i = 0; i < EXTCON_IRQ_END; i++) {
 		pirq = platform_get_irq(pdev, i);
+		if (pirq < 0)
+			return pirq;
+
 		info->irq[i] = regmap_irq_get_virq(info->regmap_irqc, pirq);
 		if (info->irq[i] < 0) {
 			dev_err(&pdev->dev,

drivers/extcon/extcon-usbc-cros-ec.c

@@ -34,16 +34,26 @@ struct cros_ec_extcon_info {
 
 	struct notifier_block notifier;
 
+	unsigned int dr; /* data role */
+	bool pr; /* power role (true if VBUS enabled) */
 	bool dp; /* DisplayPort enabled */
 	bool mux; /* SuperSpeed (usb3) enabled */
 	unsigned int power_type;
 };
 
 static const unsigned int usb_type_c_cable[] = {
+	EXTCON_USB,
+	EXTCON_USB_HOST,
 	EXTCON_DISP_DP,
 	EXTCON_NONE,
 };
 
+enum usb_data_roles {
+	DR_NONE,
+	DR_HOST,
+	DR_DEVICE,
+};
+
 /**
  * cros_ec_pd_command() - Send a command to the EC.
  * @info: pointer to struct cros_ec_extcon_info
@@ -150,6 +160,7 @@ static int cros_ec_usb_get_role(struct cros_ec_extcon_info *info,
 	pd_control.port = info->port_id;
 	pd_control.role = USB_PD_CTRL_ROLE_NO_CHANGE;
 	pd_control.mux = USB_PD_CTRL_MUX_NO_CHANGE;
+	pd_control.swap = USB_PD_CTRL_SWAP_NONE;
 	ret = cros_ec_pd_command(info, EC_CMD_USB_PD_CONTROL, 1,
 				 &pd_control, sizeof(pd_control),
 				 &resp, sizeof(resp));
@@ -183,11 +194,72 @@ static int cros_ec_pd_get_num_ports(struct cros_ec_extcon_info *info)
 	return resp.num_ports;
 }
 
+static const char *cros_ec_usb_role_string(unsigned int role)
+{
+	return role == DR_NONE ? "DISCONNECTED" :
+		(role == DR_HOST ? "DFP" : "UFP");
+}
+
+static const char *cros_ec_usb_power_type_string(unsigned int type)
+{
+	switch (type) {
+	case USB_CHG_TYPE_NONE:
+		return "USB_CHG_TYPE_NONE";
+	case USB_CHG_TYPE_PD:
+		return "USB_CHG_TYPE_PD";
+	case USB_CHG_TYPE_PROPRIETARY:
+		return "USB_CHG_TYPE_PROPRIETARY";
+	case USB_CHG_TYPE_C:
+		return "USB_CHG_TYPE_C";
+	case USB_CHG_TYPE_BC12_DCP:
+		return "USB_CHG_TYPE_BC12_DCP";
+	case USB_CHG_TYPE_BC12_CDP:
+		return "USB_CHG_TYPE_BC12_CDP";
+	case USB_CHG_TYPE_BC12_SDP:
+		return "USB_CHG_TYPE_BC12_SDP";
+	case USB_CHG_TYPE_OTHER:
+		return "USB_CHG_TYPE_OTHER";
+	case USB_CHG_TYPE_VBUS:
+		return "USB_CHG_TYPE_VBUS";
+	case USB_CHG_TYPE_UNKNOWN:
+		return "USB_CHG_TYPE_UNKNOWN";
+	default:
+		return "USB_CHG_TYPE_UNKNOWN";
+	}
+}
+
+static bool cros_ec_usb_power_type_is_wall_wart(unsigned int type,
+						unsigned int role)
+{
+	switch (type) {
+	/* FIXME : Guppy, Donnettes, and other chargers will be miscategorized
+	 * because they identify with USB_CHG_TYPE_C, but we can't return true
+	 * here from that code because that breaks Suzy-Q and other kinds of
+	 * USB Type-C cables and peripherals.
+	 */
+	case USB_CHG_TYPE_PROPRIETARY:
+	case USB_CHG_TYPE_BC12_DCP:
+		return true;
+	case USB_CHG_TYPE_PD:
+	case USB_CHG_TYPE_C:
+	case USB_CHG_TYPE_BC12_CDP:
+	case USB_CHG_TYPE_BC12_SDP:
+	case USB_CHG_TYPE_OTHER:
+	case USB_CHG_TYPE_VBUS:
+	case USB_CHG_TYPE_UNKNOWN:
+	case USB_CHG_TYPE_NONE:
+	default:
+		return false;
+	}
+}
+
 static int extcon_cros_ec_detect_cable(struct cros_ec_extcon_info *info,
 				       bool force)
 {
 	struct device *dev = info->dev;
 	int role, power_type;
+	unsigned int dr = DR_NONE;
+	bool pr = false;
 	bool polarity = false;
 	bool dp = false;
 	bool mux = false;
@@ -206,9 +278,12 @@ static int extcon_cros_ec_detect_cable(struct cros_ec_extcon_info *info,
 			dev_err(dev, "failed getting role err = %d\n", role);
 			return role;
 		}
+		dev_dbg(dev, "disconnected\n");
 	} else {
 		int pd_mux_state;
 
+		dr = (role & PD_CTRL_RESP_ROLE_DATA) ? DR_HOST : DR_DEVICE;
+		pr = (role & PD_CTRL_RESP_ROLE_POWER);
 		pd_mux_state = cros_ec_usb_get_pd_mux_state(info);
 		if (pd_mux_state < 0)
 			pd_mux_state = USB_PD_MUX_USB_ENABLED;
@@ -216,20 +291,62 @@ static int extcon_cros_ec_detect_cable(struct cros_ec_extcon_info *info,
 		dp = pd_mux_state & USB_PD_MUX_DP_ENABLED;
 		mux = pd_mux_state & USB_PD_MUX_USB_ENABLED;
 		hpd = pd_mux_state & USB_PD_MUX_HPD_IRQ;
-	}
 
-	if (force || info->dp != dp || info->mux != mux ||
-		info->power_type != power_type) {
+		dev_dbg(dev,
+			"connected role 0x%x pwr type %d dr %d pr %d pol %d mux %d dp %d hpd %d\n",
+			role, power_type, dr, pr, polarity, mux, dp, hpd);
+	}
 
+	/*
+	 * When there is no USB host (e.g. USB PD charger),
+	 * we are not really a UFP for the AP.
+	 */
+	if (dr == DR_DEVICE &&
+	    cros_ec_usb_power_type_is_wall_wart(power_type, role))
+		dr = DR_NONE;
+
+	if (force || info->dr != dr || info->pr != pr || info->dp != dp ||
+	    info->mux != mux || info->power_type != power_type) {
+		bool host_connected = false, device_connected = false;
+
+		dev_dbg(dev, "Type/Role switch! type = %s role = %s\n",
+			cros_ec_usb_power_type_string(power_type),
+			cros_ec_usb_role_string(dr));
+		info->dr = dr;
+		info->pr = pr;
 		info->dp = dp;
 		info->mux = mux;
 		info->power_type = power_type;
 
-		extcon_set_state(info->edev, EXTCON_DISP_DP, dp);
+		if (dr == DR_DEVICE)
+			device_connected = true;
+		else if (dr == DR_HOST)
+			host_connected = true;
 
+		extcon_set_state(info->edev, EXTCON_USB, device_connected);
+		extcon_set_state(info->edev, EXTCON_USB_HOST, host_connected);
+		extcon_set_state(info->edev, EXTCON_DISP_DP, dp);
+		extcon_set_property(info->edev, EXTCON_USB,
+				    EXTCON_PROP_USB_VBUS,
+				    (union extcon_property_value)(int)pr);
+		extcon_set_property(info->edev, EXTCON_USB_HOST,
+				    EXTCON_PROP_USB_VBUS,
+				    (union extcon_property_value)(int)pr);
+		extcon_set_property(info->edev, EXTCON_USB,
+				    EXTCON_PROP_USB_TYPEC_POLARITY,
+				    (union extcon_property_value)(int)polarity);
+		extcon_set_property(info->edev, EXTCON_USB_HOST,
+				    EXTCON_PROP_USB_TYPEC_POLARITY,
+				    (union extcon_property_value)(int)polarity);
 		extcon_set_property(info->edev, EXTCON_DISP_DP,
 				    EXTCON_PROP_USB_TYPEC_POLARITY,
 				    (union extcon_property_value)(int)polarity);
+		extcon_set_property(info->edev, EXTCON_USB,
+				    EXTCON_PROP_USB_SS,
+				    (union extcon_property_value)(int)mux);
+		extcon_set_property(info->edev, EXTCON_USB_HOST,
+				    EXTCON_PROP_USB_SS,
+				    (union extcon_property_value)(int)mux);
 		extcon_set_property(info->edev, EXTCON_DISP_DP,
 				    EXTCON_PROP_USB_SS,
 				    (union extcon_property_value)(int)mux);
@@ -237,6 +354,8 @@ static int extcon_cros_ec_detect_cable(struct cros_ec_extcon_info *info,
 				    EXTCON_PROP_DISP_HPD,
 				    (union extcon_property_value)(int)hpd);
 
+		extcon_sync(info->edev, EXTCON_USB);
+		extcon_sync(info->edev, EXTCON_USB_HOST);
 		extcon_sync(info->edev, EXTCON_DISP_DP);
 
 	} else if (hpd) {
@@ -322,13 +441,28 @@ static int extcon_cros_ec_probe(struct platform_device *pdev)
 		return ret;
 	}
 
+	extcon_set_property_capability(info->edev, EXTCON_USB,
+				       EXTCON_PROP_USB_VBUS);
+	extcon_set_property_capability(info->edev, EXTCON_USB_HOST,
+				       EXTCON_PROP_USB_VBUS);
+	extcon_set_property_capability(info->edev, EXTCON_USB,
+				       EXTCON_PROP_USB_TYPEC_POLARITY);
+	extcon_set_property_capability(info->edev, EXTCON_USB_HOST,
+				       EXTCON_PROP_USB_TYPEC_POLARITY);
 	extcon_set_property_capability(info->edev, EXTCON_DISP_DP,
 				       EXTCON_PROP_USB_TYPEC_POLARITY);
+	extcon_set_property_capability(info->edev, EXTCON_USB,
+				       EXTCON_PROP_USB_SS);
+	extcon_set_property_capability(info->edev, EXTCON_USB_HOST,
+				       EXTCON_PROP_USB_SS);
 	extcon_set_property_capability(info->edev, EXTCON_DISP_DP,
 				       EXTCON_PROP_USB_SS);
 	extcon_set_property_capability(info->edev, EXTCON_DISP_DP,
 				       EXTCON_PROP_DISP_HPD);
 
+	info->dr = DR_NONE;
+	info->pr = false;
+
 	platform_set_drvdata(pdev, info);
 
 	/* Get PD events from the EC */

include/linux/mfd/axp20x.h

@@ -645,11 +645,6 @@ struct axp20x_dev {
 	const struct regmap_irq_chip	*regmap_irq_chip;
 };
 
-struct axp288_extcon_pdata {
-	/* GPIO pin control to switch D+/D- lines b/w PMIC and SOC */
-	struct gpio_desc *gpio_mux_cntl;
-};
-
 /* generic helper function for reading 9-16 bit wide regs */
 static inline int axp20x_read_variable_width(struct regmap *regmap,
 	unsigned int reg, unsigned int width)

include/linux/mfd/cros_ec_commands.h

@@ -2904,16 +2904,33 @@ enum usb_pd_control_mux {
 	USB_PD_CTRL_MUX_AUTO = 5,
 };
 
+enum usb_pd_control_swap {
+	USB_PD_CTRL_SWAP_NONE = 0,
+	USB_PD_CTRL_SWAP_DATA = 1,
+	USB_PD_CTRL_SWAP_POWER = 2,
+	USB_PD_CTRL_SWAP_VCONN = 3,
+	USB_PD_CTRL_SWAP_COUNT
+};
+
 struct ec_params_usb_pd_control {
 	uint8_t port;
 	uint8_t role;
 	uint8_t mux;
+	uint8_t swap;
 } __packed;
 
 #define PD_CTRL_RESP_ENABLED_COMMS      (1 << 0) /* Communication enabled */
 #define PD_CTRL_RESP_ENABLED_CONNECTED  (1 << 1) /* Device connected */
 #define PD_CTRL_RESP_ENABLED_PD_CAPABLE (1 << 2) /* Partner is PD capable */
 
+#define PD_CTRL_RESP_ROLE_POWER         BIT(0) /* 0=SNK/1=SRC */
+#define PD_CTRL_RESP_ROLE_DATA          BIT(1) /* 0=UFP/1=DFP */
+#define PD_CTRL_RESP_ROLE_VCONN         BIT(2) /* Vconn status */
+#define PD_CTRL_RESP_ROLE_DR_POWER      BIT(3) /* Partner is dualrole power */
+#define PD_CTRL_RESP_ROLE_DR_DATA       BIT(4) /* Partner is dualrole data */
+#define PD_CTRL_RESP_ROLE_USB_COMM      BIT(5) /* Partner USB comm capable */
+#define PD_CTRL_RESP_ROLE_EXT_POWERED   BIT(6) /* Partner externally powerd */
+
 struct ec_response_usb_pd_control_v1 {
 	uint8_t enabled;
 	uint8_t role;