Support MC_CMD_PTP_OUT_GET_TIMESTAMP_CORRECTIONS_V2.  Extract general
 timestamp corrections in addition to PTP corrections.  Apply receive
 timestamp corrections for general datapath receive timestamping, and
 correspondingly for transmit.
Signed-off-by: Laurence Evans <levans@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use timestamp conversion function with correction to avoid duplicate
 correction handling.
Signed-off-by: Laurence Evans <levans@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We check the license for TX hardware timestamping capability.
The PTP probe will have enabled PTP sync events from the adapter.  If
 later, at TX queue init, it turns out we do not have the license, we
 don't need the sync events either.
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For this we create and use one or more new TX queues on the PTP channel,
 and enable sync events for it.
Based on a patch by Martin Habets <mhabets@solarflare.com>.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TX timestamps on 8000 series are supplied from the MAC. This timestamp is
 only 48 bits long. The high order bits from the last time sync event are
 used for the top 16 bits.
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we try to enable the feature and do not have the license for it, the
 MCPU will refuse and fail our TX queue init.
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We can now transmit SKBs in 2 ways:
1. Via the MC (for the 7XXX series and earlier), using
   efx_ptp_xmit_skb_mc().
2. Via the TX queues on the dedicated PTP channel (8XXX series and later),
   using efx_ptp_xmit_skb_queue().
The PTP worker thread uses the method set up at probe time. It never
 checked the return code from the old efx_ptp_xmit_skb(), so it now
 returns void.
We increment the TX dropped counter of the device if the transmit fails.

As a result of the probe per channel the remove gets called multiple times.
 Clean up efx->ptp_data properly to avoid the 2nd call blowing up.
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use MC capability MC_CMD_GET_CAPABILITIES_V2_OUT_TX_MAC_TIMESTAMPING to
 detect whether the NIC supports timestamping packets sent out the main
 datapath.
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before this work, TX timestamping is done by sending each SKB to the MC.
On the 8000 series (Medford1) we have high speed timestamping via the
 MAC, which means we can use normal TX queues for this without a
 significant drop in bandwidth.  On the X2000 series (Medford2) support
 for transmitting via the MC is removed, so the new way must be used.

This patch enables timestamping on a TX queue, if requested.
It also enhances TX event handling to process the extra completion events,
 and puts the time in the SKB.
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The NAPI budget is only for RX processing work, not other work such as
 TX or MCDI completion handling.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, we unhash a dying net from netns_ids lists
under rtnl_lock(). It's a leftover from the time when
net::netns_ids was introduced. There was no net::nsid_lock,
and rtnl_lock() was mostly need to order modification
of alive nets nsid idr, i.e. for:
	for_each_net(tmp) {
		...
		id = __peernet2id(tmp, net);
		idr_remove(&tmp->netns_ids, id);
		...
	}

Since we have net::nsid_lock, the modifications are
protected by this local lock, and now we may introduce
better scheme of netns_ids destruction.

Let's look at the functions peernet2id_alloc() and
get_net_ns_by_id(). Previous commits taught these
functions to work well with dying net acquired from
rtnl unlocked lists. And they are the only functions
which can hash a net to netns_ids or obtain from there.
And as easy to check, other netns_ids operating functions
works with id, not with net pointers. So, we do not
need rtnl_lock to synchronize cleanup_net() with all them.

The another property, which is used in the patch,
is that net is unhashed from net_namespace_list
in the only place and by the only process. So,
we avoid excess rcu_read_lock() or rtnl_lock(),
when we'are iterating over the list in unhash_nsid().

All the above makes possible to keep rtnl_lock() locked
only for net->list deletion, and completely avoid it
for netns_ids unhashing and destruction. As these two
doings may take long time (e.g., memory allocation
to send skb), the patch should positively act on
the scalability and signify decrease the time, which
rtnl_lock() is held in cleanup_net().
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Avoid negative netdev refcount in error flow of xfrm state add, from
    Aviad Yehezkel.

 2) Fix tcpdump decoding of IPSEC decap'd frames by filling in the
    ethernet header protocol field in xfrm{4,6}_mode_tunnel_input().
    From Yossi Kuperman.

 3) Fix a syzbot triggered skb_under_panic in pppoe having to do with
    failing to allocate an appropriate amount of headroom. From
    Guillaume Nault.

 4) Fix memory leak in vmxnet3 driver, from Neil Horman.

 5) Cure out-of-bounds packet memory access in em_nbyte EMATCH module,
    from Wolfgang Bumiller.

 6) Restrict what kinds of sockets can be bound to the KCM multiplexer
    and also disallow when another layer has attached to the socket and
    made use of sk_user_data. From Tom Herbert.

 7) Fix use before init of IOTLB in vhost code, from Jason Wang.

 8) Correct STACR register write bit definition in IBM emac driver, from
    Ivan Mikhaylov.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net/ibm/emac: wrong bit is used for STA control register write
  net/ibm/emac: add 8192 rx/tx fifo size
  vhost: do not try to access device IOTLB when not initialized
  vhost: use mutex_lock_nested() in vhost_dev_lock_vqs()
  i40e: flower: check if TC offload is enabled on a netdev
  qed: Free reserved MR tid
  qed: Remove reserveration of dpi for kernel
  kcm: Check if sk_user_data already set in kcm_attach
  kcm: Only allow TCP sockets to be attached to a KCM mux
  net: sched: fix TCF_LAYER_LINK case in tcf_get_base_ptr
  net: sched: em_nbyte: don't add the data offset twice
  mlxsw: spectrum_router: Don't log an error on missing neighbor
  vmxnet3: repair memory leak
  ipv6: Fix getsockopt() for sockets with default IPV6_AUTOFLOWLABEL
  pppoe: take ->needed_headroom of lower device into account on xmit
  xfrm: fix boolean assignment in xfrm_get_type_offload
  xfrm: Fix eth_hdr(skb)->h_proto to reflect inner IP version
  xfrm: fix error flow in case of add state fails
  xfrm: Add SA to hardware at the end of xfrm_state_construct()

no users since 2014
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

same story...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Same story as with dev_ifsioc(), except that the last cases with non-trivial
conversions had been taken out in 2013...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Once upon a time net/socket.c:dev_ifsioc() used to handle SIOCSHWTSTAMP and
SIOCSIFMAP.  These have different native and compat layout, so the format
conversion had been needed.  In 2009 these two cases had been taken out,
turning the rest into a convoluted way to calling sock_do_ioctl().  We copy
compat structure into native one, call sock_do_ioctl() on that and copy
the result back for the in/out ioctls.  No layout transformation anywhere,
so we might as well just call sock_do_ioctl() and skip all the headache with
copying.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Only two of dev_ioctl() callers may pass SIOCGIFCONF to it.
Separating that codepath from the rest of dev_ioctl() allows both
to simplify dev_ioctl() itself (all other cases work with struct ifreq *)
*and* seriously simplify the compat side of that beast: all it takes
is passing to inet_gifconf() an extra argument - the size of individual
records (sizeof(struct ifreq) or sizeof(struct compat_ifreq)).  With
dev_ifconf() called directly from sock_do_ioctl()/compat_dev_ifconf()
that's easy to arrange.

As the result, compat side of SIOCGIFCONF doesn't need any
allocations, copy_in_user() back and forth, etc.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull sparc bugfix from David Miller:
 "Sparc Makefile typo fix"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: fix typo in CONFIG_CRYPTO_DES_SPARC64 => CONFIG_CRYPTO_CAMELLIA_SPARC64

STA control register has areas of mode and opcodes for opeations. 18 bit is
using for mode selection, where 0 is old MIO/MDIO access method and 1 is
indirect access mode. 19-20 bits are using for setting up read/write
operation(STA opcodes). In current state 'read' is set into old MIO/MDIO mode
with 19 bit and write operation is set into 18 bit which is mode selection,
not a write operation. To correlate write with read we set it into 20 bit.
All those bit operations are MSB 0 based.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

emac4syn chips has availability to use 8192 rx/tx fifo buffer sizes,
in current state if we set it up in dts 8192 as example, we will get
only 2048 which may impact on network speed.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
100GbE Intel Wired LAN Driver Updates 2018-01-24

This series contains updates to fm10k only.

Alex fixes MACVLAN offload for fm10k, where we were not seeing unicast
packets being received because we did not correctly configure the
default VLAN ID for the port and defaulting to 0.

Jake cleans up unnecessary parenthesis in a couple of "if" statements.
Fixed the driver to stop adding VLAN 0 into the VLAN table, since it
would cause the VLAN table to be inconsistent between the PF and VF.
Also fixed an issue where we were assuming that VLAN 1 is enabled when
the default VLAN ID is not set, so resolve by not requesting any filters
for the default_vid if it has not yet been assigned.

Ngai fixes an issue which was generating a dmesg regarding unbale to
kill a particular VLAN ID for the device.  This is due to
ndo_vlan_rx_kill_vid() exits with an error and the handler for this ndo
is fm10k_update_vid() which exits prematurely under PF VLAN management.
So to resolve, we must check the VLAN update action type before exiting
fm10k_update_vid(), and act appropriately based on the action type.
Also corrected code comment typos.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Clarify the comment for when entering promiscuous mode that we update
the VLAN table. Add a comment distinguishing the case where we're
exiting promiscuous mode and need to clear the entire VLAN table.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@gmail.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Since commit 856dfd69e84f ("fm10k: Fix multicast mode synch issues",
2016-03-03) we've incorrectly assumed that VLAN 1 is enabled when the
default VID is not set.

This occurs because we check the default_vid and if it's zero, start
several loops over the active_vlans bitmask at 1, instead of checking to
ensure that that bit is active.

This happened because of commit d9ff3ee8efe9 ("fm10k: Add support for
VLAN 0 w/o default VLAN", 2014-08-07) which mistakenly assumed that we
should send requests for MAC and VLAN filters with VLAN 0 when the
default_vid isn't set.

However, the switch generally considers this an invalid configuration,
so the only time we'd have a default_vid of 0 is when the switch is
down.

Instead, lets just not request any filters for the default_vid if it's
not yet been assigned.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently, when the driver loads, it sends a request to add VLAN 0 to the
VLAN table. For the PF, this is honored, and VLAN 0 is indeed set. For
the VF, this request is silently converted into a request for the
default VLAN as defined by either the switch vid or the PF vid.

This results in the odd behavior that the VLAN table doesn't appear
consistent between the PF and the VF.

Furthermore, setting a MAC filter with VLAN 0 is generally considered an
invalid configuration by the switch, and since commit 856dfd69e84f
("fm10k: Fix multicast mode synch issues", 2016-03-03) we've had code
which prevents us from ever sending such a request.

Since there's not really a good reason to keep VLAN 0 in the VLAN table,
stop requesting it in fm10k_restore_rx_state().

This might seem to indicate that we would no longer properly configure
the MAC and VLAN tables for the default vid. However, due to the way
that fm10k_find_next_vlan() behaves, it will always return the
default_vid as enabled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When a VF is under PF VLAN assignment:

ip link set <pf> vf <#> vlan <vid>

This will remove all previous entries in the VLAN table including those
generated by VLAN interfaces created on the VF. The issue arises when
the VF is under PF VLAN assignment and one or more of these VLAN
interfaces of the VF are deleted. When deleting these VLAN interfaces,
the following message will be generated in "dmesg":

failed to kill vid 0081/<vid> for device <vf>

This is due to the fact that "ndo_vlan_rx_kill_vid" exits with an error.
The handler for this ndo is "fm10k_update_vid". Any calls to this
function while under PF VLAN management will exit prematurely and, thus,
it will generate the failure message.

Additionally, since "fm10k_update_vid" exits prematurely, none of the
VLAN update is performed. So, even though the actual VLAN interfaces of
the VF will be deleted, the active_vlans bitmask is not cleared. When
the VF is no longer under PF VLAN assignment, the driver mistakenly
restores the previous entries of the VLAN table based on an
unsynchronized list of active VLANs.

The solution to this issue involves checking the VLAN update action type
before exiting "fm10k_update_vid". If the VLAN update action type is to
"add", this action will not be permitted while the VF is under PF VLAN
assignment and the VLAN update is abandoned like before.

However, if the VLAN update action type is to "kill", then we need to
also clear the active_vlans bitmask. However, we don't need to actually
queue any messages to the PF, because the MAC and VLAN tables have
already been cleared, and the PF would silently ignore these requests
anyways.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This fixes a few warnings found by checkpatch.pl --strict
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Fixes the following sparse warning:

drivers/net/ethernet/chelsio/cxgb4/cxgb4_tc_flower.c:46:27: warning:
 symbol 'pedits' was not declared. Should it be static?

Fixes: 27ece1f3 ("cxgb4: add tc flower support for ETH-DMAC rewrite")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The code will try to access dev->iotlb when processing
VHOST_IOTLB_INVALIDATE even if it was not initialized which may lead
to NULL pointer dereference. Fixes this by check dev->iotlb before.

Fixes: 6b1e6cc7 ("vhost: new device IOTLB API")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We used to call mutex_lock() in vhost_dev_lock_vqs() which tries to
hold mutexes of all virtqueues. This may confuse lockdep to report a
possible deadlock because of trying to hold locks belong to same
class. Switch to use mutex_lock_nested() to avoid false positive.

Fixes: 6b1e6cc7 ("vhost: new device IOTLB API")
Reported-by: syzbot+dbb7c1161485e61b0241@syzkaller.appspotmail.com
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When building the erspan header for either v1 or v2, the eth_hdr()
does not point to the right inner packet's eth_hdr,
causing kasan report use-after-free and slab-out-of-bouds read.

The patch fixes the following syzkaller issues:
[1] BUG: KASAN: slab-out-of-bounds in erspan_xmit+0x22d4/0x2430 net/ipv4/ip_gre.c:735
[2] BUG: KASAN: slab-out-of-bounds in erspan_build_header+0x3bf/0x3d0 net/ipv4/ip_gre.c:698
[3] BUG: KASAN: use-after-free in erspan_xmit+0x22d4/0x2430 net/ipv4/ip_gre.c:735
[4] BUG: KASAN: use-after-free in erspan_build_header+0x3bf/0x3d0 net/ipv4/ip_gre.c:698

[2] CPU: 0 PID: 3654 Comm: syzkaller377964 Not tainted 4.15.0-rc9+ #185
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:17 [inline]
 dump_stack+0x194/0x257 lib/dump_stack.c:53
 print_address_description+0x73/0x250 mm/kasan/report.c:252
 kasan_report_error mm/kasan/report.c:351 [inline]
 kasan_report+0x25b/0x340 mm/kasan/report.c:409
 __asan_report_load_n_noabort+0xf/0x20 mm/kasan/report.c:440
 erspan_build_header+0x3bf/0x3d0 net/ipv4/ip_gre.c:698
 erspan_xmit+0x3b8/0x13b0 net/ipv4/ip_gre.c:740
 __netdev_start_xmit include/linux/netdevice.h:4042 [inline]
 netdev_start_xmit include/linux/netdevice.h:4051 [inline]
 packet_direct_xmit+0x315/0x6b0 net/packet/af_packet.c:266
 packet_snd net/packet/af_packet.c:2943 [inline]
 packet_sendmsg+0x3aed/0x60b0 net/packet/af_packet.c:2968
 sock_sendmsg_nosec net/socket.c:638 [inline]
 sock_sendmsg+0xca/0x110 net/socket.c:648
 SYSC_sendto+0x361/0x5c0 net/socket.c:1729
 SyS_sendto+0x40/0x50 net/socket.c:1697
 do_syscall_32_irqs_on arch/x86/entry/common.c:327 [inline]
 do_fast_syscall_32+0x3ee/0xf9d arch/x86/entry/common.c:389
 entry_SYSENTER_compat+0x54/0x63 arch/x86/entry/entry_64_compat.S:129
RIP: 0023:0xf7fcfc79
RSP: 002b:00000000ffc6976c EFLAGS: 00000286 ORIG_RAX: 0000000000000171
RAX: ffffffffffffffda RBX: 0000000000000004 RCX: 0000000020011000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000020008000
RBP: 000000000000001c R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000

Fixes: f551c91d ("net: erspan: introduce erspan v2 for ip_gre")
Fixes: 84e54fe0 ("gre: introduce native tunnel support for ERSPAN")
Reported-by: syzbot+9723f2d288e49b492cf0@syzkaller.appspotmail.com
Reported-by: syzbot+f0ddeb2b032a8e1d9098@syzkaller.appspotmail.com
Reported-by: syzbot+f14b3703cd8d7670203f@syzkaller.appspotmail.com
Reported-by: syzbot+eefa384efad8d7997f20@syzkaller.appspotmail.com
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since TC block changes drivers are required to check if
the TC hw offload flag is set on the interface themselves.

Fixes: 2f4b411a ("i40e: Enable cloud filters via tc-flower")
Fixes: 44ae12a7 ("net: sched: move the can_offload check from binding phase to rule insertion phase")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the typo CONFIG_CRYPTO_DES_SPARC64 => CONFIG_CRYPTO_CAMELLIA_SPARC64

Fixes: 81658ad0 ("sparc64: Add CAMELLIA driver making use of the new camellia opcodes.")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>