After a few updates against swnode APIs the kernel documentation, i.e.
for swnode group registration and unregistration deviates from the one
for swnode array. In general, the same rules are applied to both.
Hence, synchronize descriptions of swnode array and group APIs
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210308103644.81960-1-andriy.shevchenko@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This is a follow-up for:
commit 3c9ea428 ("clk: Mark fwnodes when their clock provider is added/removed")

The above commit updated the deprecated of_clk_add_provider(),
but missed to update the preferred of_clk_add_hw_provider().
Update it now.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20210210114435.122242-2-tudor.ambarus@microchip.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 3e4c982f.

Since all reported issues due to fw_devlink=on should be addressed by
this series, revert the revert. fw_devlink=on Take II.
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20210302211133.2244281-4-saravanak@google.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Device link status was not getting updated correctly when
device_bind_driver() is called on a device. This causes a warning[1].
Fix this by updating device links that can be updated and dropping
device links that can't be updated to a sensible state.

[1] - https://lore.kernel.org/lkml/56f7d032-ba5a-a8c7-23de-2969d98c527e@nvidia.com/Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20210302211133.2244281-3-saravanak@google.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There's no point in adding a device to the deferred probe list if we
know for sure that it doesn't have a matching driver. So, check if a
device can match with a driver before adding it to the deferred probe
list.
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20210302211133.2244281-2-saravanak@google.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently gcc seems to inline devtmpfs_setup() into devtmpfsd(), so
its memory footprint isn't reclaimed as intended. Mark it noinline to
make sure it gets put in .init.text.

While here, setup_done can also be put in .init.data: After complete()
releases the internal spinlock, the completion object is never touched
again by that thread, and the waiting thread doesn't proceed until it
observes ->done while holding that spinlock.

This is now the same pattern as for kthreadd_done in init/main.c:
complete() is done in a __ref function, while the corresponding
wait_for_completion() is in an __init function.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20210312103027.2701413-2-linux@rasmusvillemoes.dkSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Calling complete() from within the __init function is wrong -
theoretically, the init process could proceed all the way to freeing
the init mem before the devtmpfsd thread gets to execute the return
instruction in devtmpfs_setup().

In practice, it seems to be harmless as gcc inlines devtmpfs_setup()
into devtmpfsd(). So the calls of the __init functions init_chdir()
etc. actually happen from devtmpfs_setup(), but the __ref on that one
silences modpost (it's all right, because those calls happen before
the complete()). But it does make the __init annotation of the setup
function moot, which we'll fix in a subsequent patch.

Fixes: bcbacc49 ("devtmpfs: refactor devtmpfsd()")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20210312103027.2701413-1-linux@rasmusvillemoes.dkSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The variable retval is being initialized with a value that is never read
and it is being updated later with a new value.  Clean this up by
initializing retval to -ENOMEM and remove the assignment to retval
on the !dev failure path.

Kudos to Rafael for the improved fix suggestion.
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210218202837.516231-1-colin.king@canonical.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix the following coccicheck warnings:

./tools/testing/selftests/firmware/fw_namespace.c:98:54-59: WARNING:
conversion to bool not needed here.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Link: https://lore.kernel.org/r/1613639529-41139-1-git-send-email-jiapeng.chong@linux.alibaba.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

No need to save the debugfs dentry for the "devices_deferred" debugfs
file (gotta love the juxtaposition), if we need to remove it we can look
it up from debugfs itself.

Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20210216142400.3759099-2-gregkh@linuxfoundation.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There is no need to keep around a pointer to a dentry when all it is
used for is to remove the debugfs file when tearing things down.  As the
name is simple, have debugfs look up the dentry when removing things,
keeping the logic much simpler.

Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20210216142400.3759099-1-gregkh@linuxfoundation.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove module bits in the auxiliary bus code since the auxiliary bus
cannot be built as a module and the relevant code is not needed.

Cc: Dave Ertman <david.m.ertman@intel.com>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161307488980.1896017.15627190714413338196.stgit@djiang5-desk3.ch.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s/subsytem/subsystem/
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Link: https://lore.kernel.org/r/20210320201240.23745-1-unixbhaskar@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull ext4 fixes from Ted Ts'o:
 "Miscellaneous ext4 bug fixes for v5.12"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: initialize ret to suppress smatch warning
  ext4: stop inode update before return
  ext4: fix rename whiteout with fast commit
  ext4: fix timer use-after-free on failed mount
  ext4: fix potential error in ext4_do_update_inode
  ext4: do not try to set xattr into ea_inode if value is empty
  ext4: do not iput inode under running transaction in ext4_rename()
  ext4: find old entry again if failed to rename whiteout
  ext4: fix error handling in ext4_end_enable_verity()
  ext4: fix bh ref count on error paths
  fs/ext4: fix integer overflow in s_log_groups_per_flex
  ext4: add reclaim checks to xattr code
  ext4: shrink race window in ext4_should_retry_alloc()

Pull io_uring followup fixes from Jens Axboe:

 - The SIGSTOP change from Eric, so we properly ignore that for
   PF_IO_WORKER threads.

 - Disallow sending signals to PF_IO_WORKER threads in general, we're
   not interested in having them funnel back to the io_uring owning
   task.

 - Stable fix from Stefan, ensuring we properly break links for short
   send/sendmsg recv/recvmsg if MSG_WAITALL is set.

 - Catch and loop when needing to run task_work before a PF_IO_WORKER
   threads goes to sleep.

* tag 'io_uring-5.12-2021-03-21' of git://git.kernel.dk/linux-block:
  io_uring: call req_set_fail_links() on short send[msg]()/recv[msg]() with MSG_WAITALL
  io-wq: ensure task is running before processing task_work
  signal: don't allow STOP on PF_IO_WORKER threads
  signal: don't allow sending any signals to PF_IO_WORKER threads

Pull staging and IIO driver fixes from Greg KH:
 "Some small staging and IIO driver fixes:

   - MAINTAINERS changes for the move of the staging mailing list

   - comedi driver fixes to get request_irq() to work correctly

   - counter driver fixes for reported issues with iio devices

   - tiny iio driver fixes for reported issues.

  All of these have been in linux-next with no reported problems"

* tag 'staging-5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: vt665x: fix alignment constraints
  staging: comedi: cb_pcidas64: fix request_irq() warn
  staging: comedi: cb_pcidas: fix request_irq() warn
  MAINTAINERS: move the staging subsystem to lists.linux.dev
  MAINTAINERS: move some real subsystems off of the staging mailing list
  iio: gyro: mpu3050: Fix error handling in mpu3050_trigger_handler
  iio: hid-sensor-temperature: Fix issues of timestamp channel
  iio: hid-sensor-humidity: Fix alignment issue of timestamp channel
  counter: stm32-timer-cnt: fix ceiling miss-alignment with reload register
  counter: stm32-timer-cnt: fix ceiling write max value
  counter: stm32-timer-cnt: Report count function when SLAVE_MODE_DISABLED
  iio: adc: ab8500-gpadc: Fix off by 10 to 3
  iio:adc:stm32-adc: Add HAS_IOMEM dependency
  iio: adis16400: Fix an error code in adis16400_initial_setup()
  iio: adc: adi-axi-adc: add proper Kconfig dependencies
  iio: adc: ad7949: fix wrong ADC result due to incorrect bit mask
  iio: hid-sensor-prox: Fix scale not correct issue
  iio:adc:qcom-spmi-vadc: add default scale to LR_MUX2_BAT_ID channel

Pull USB and Thunderbolt driver fixes from Greg KH:
 "Here are some small Thunderbolt and USB driver fixes for some reported
  issues:

   - thunderbolt fixes for minor problems

   - typec fixes for power issues

   - usb-storage quirk addition

   - usbip bugfix

   - dwc3 bugfix when stopping transfers

   - cdnsp bugfix for isoc transfers

   - gadget use-after-free fix

  All have been in linux-next this week with no reported issues"

* tag 'usb-5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: typec: tcpm: Skip sink_cap query only when VDM sm is busy
  usb: dwc3: gadget: Prevent EP queuing while stopping transfers
  usb: typec: tcpm: Invoke power_supply_changed for tcpm-source-psy-
  usb: typec: Remove vdo[3] part of tps6598x_rx_identity_reg struct
  usb-storage: Add quirk to defeat Kindle's automatic unload
  usb: gadget: configfs: Fix KASAN use-after-free
  usbip: Fix incorrect double assignment to udc->ud.tcp_rx
  usb: cdnsp: Fixes incorrect value in ISOC TRB
  thunderbolt: Increase runtime PM reference count on DP tunnel discovery
  thunderbolt: Initialize HopID IDAs in tb_switch_alloc()

Pull irq fix from Ingo Molnar:
 "A change to robustify force-threaded IRQ handlers to always disable
  interrupts, plus a DocBook fix.

  The force-threaded IRQ handler change has been accelerated from the
  normal schedule of such a change to keep the bad pattern/workaround of
  spin_lock_irqsave() in handlers or IRQF_NOTHREAD as a kludge from
  spreading"

* tag 'irq-urgent-2021-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq: Disable interrupts for force threaded handlers
  genirq/irq_sim: Fix typos in kernel doc (fnode -> fwnode)

Pull perf fixes from Ingo Molnar:
 "Boundary condition fixes for bugs unearthed by the perf fuzzer"

* tag 'perf-urgent-2021-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel: Fix unchecked MSR access error caused by VLBR_EVENT
  perf/x86/intel: Fix a crash caused by zero PEBS status

Pull locking fixes from Ingo Molnar:

 - Get static calls & modules right. Hopefully.

 - WW mutex fixes

* tag 'locking-urgent-2021-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  static_call: Fix static_call_update() sanity check
  static_call: Align static_call_is_init() patching condition
  static_call: Fix static_call_set_init()
  locking/ww_mutex: Fix acquire/release imbalance in ww_acquire_init()/ww_acquire_fini()
  locking/ww_mutex: Simplify use_ww_ctx & ww_ctx handling

Pull EFI fixes from Ingo Molnar:

 - another missing RT_PROP table related fix, to ensure that the
   efivarfs pseudo filesystem fails gracefully if variable services
   are unsupported

 - use the correct alignment for literal EFI GUIDs

 - fix a use after unmap issue in the memreserve code

* tag 'efi-urgent-2021-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  efi: use 32-bit alignment for efi_guid_t literals
  firmware/efi: Fix a use after bug in efi_mem_reserve_persistent
  efivars: respect EFI_UNSUPPORTED return from firmware

Pull x86 fixes from Borislav Petkov:
 "The freshest pile of shiny x86 fixes for 5.12:

   - Add the arch-specific mapping between physical and logical CPUs to
     fix devicetree-node lookups

   - Restore the IRQ2 ignore logic

   - Fix get_nr_restart_syscall() to return the correct restart syscall
     number. Split in a 4-patches set to avoid kABI breakage when
     backporting to dead kernels"

* tag 'x86_urgent_for_v5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/apic/of: Fix CPU devicetree-node lookups
  x86/ioapic: Ignore IRQ2 again
  x86: Introduce restart_block->arch_data to remove TS_COMPAT_RESTART
  x86: Introduce TS_COMPAT_RESTART to fix get_nr_restart_syscall()
  x86: Move TS_COMPAT back to asm/thread_info.h
  kernel, fs: Introduce and use set_restart_fn() and arch_set_restart_data()

Pull powerpc fixes from Michael Ellerman:

 - Fix a possible stack corruption and subsequent DLPAR failure in the
   rpadlpar_io PCI hotplug driver

 - Two build fixes for uncommon configurations

Thanks to Christophe Leroy and Tyrel Datwyler.

* tag 'powerpc-5.12-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  PCI: rpadlpar: Fix potential drc_name corruption in store functions
  powerpc: Force inlining of cpu_has_feature() to avoid build failure
  powerpc/vdso32: Add missing _restgpr_31_x to fix build failure

Without that it's not safe to use them in a linked combination with
others.

Now combinations like IORING_OP_SENDMSG followed by IORING_OP_SPLICE
should be possible.

We already handle short reads and writes for the following opcodes:

- IORING_OP_READV
- IORING_OP_READ_FIXED
- IORING_OP_READ
- IORING_OP_WRITEV
- IORING_OP_WRITE_FIXED
- IORING_OP_WRITE
- IORING_OP_SPLICE
- IORING_OP_TEE

Now we have it for these as well:

- IORING_OP_SENDMSG
- IORING_OP_SEND
- IORING_OP_RECVMSG
- IORING_OP_RECV

For IORING_OP_RECVMSG we also check for the MSG_TRUNC and MSG_CTRUNC
flags in order to call req_set_fail_links().

There might be applications arround depending on the behavior
that even short send[msg]()/recv[msg]() retuns continue an
IOSQE_IO_LINK chain.

It's very unlikely that such applications pass in MSG_WAITALL,
which is only defined in 'man 2 recvmsg', but not in 'man 2 sendmsg'.

It's expected that the low level sock_sendmsg() call just ignores
MSG_WAITALL, as MSG_ZEROCOPY is also ignored without explicitly set
SO_ZEROCOPY.

We also expect the caller to know about the implicit truncation to
MAX_RW_COUNT, which we don't detect.

cc: netdev@vger.kernel.org
Link: https://lore.kernel.org/r/c4e1a4cc0d905314f4d5dc567e65a7b09621aab3.1615908477.git.metze@samba.orgSigned-off-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Mark the current task as running if we need to run task_work from the
io-wq threads as part of work handling. If that is the case, then return
as such so that the caller can appropriately loop back and reset if it
was part of a going-to-sleep flush.

Fixes: 3bfe6106 ("io-wq: fork worker threads from original task")
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Just like we don't allow normal signals to IO threads, don't deliver a
STOP to a task that has PF_IO_WORKER set. The IO threads don't take
signals in general, and have no means of flushing out a stop either.

Longer term, we may want to look into allowing stop of these threads,
as it relates to eg process freezing. For now, this prevents a spin
issue if a SIGSTOP is delivered to the parent task.
Reported-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>

They don't take signals individually, and even if they share signals with
the parent task, don't allow them to be delivered through the worker
thread. Linux does allow this kind of behavior for regular threads, but
it's really a compatability thing that we need not care about for the IO
threads.
Reported-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Signed-off-by: Theodore Ts'o <tytso@mit.edu>

The inode update should be stopped before returing the error code.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Link: https://lore.kernel.org/r/20210117085732.93788-1-bianpan2016@163.com
Fixes: 8016e29f ("ext4: fast commit recovery path")
Cc: stable@kernel.org
Reviewed-by: Harshad Shirwadkar <harshadshirwadkar@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

This patch adds rename whiteout support in fast commits. Note that the
whiteout object that gets created is actually char device. Which
imples, the function ext4_inode_journal_mode(struct inode *inode)
would return "JOURNAL_DATA" for this inode. This has a consequence in
fast commit code that it will make creation of the whiteout object a
fast-commit ineligible behavior and thus will fall back to full
commits. With this patch, this can be observed by running fast commits
with rename whiteout and seeing the stats generated by ext4_fc_stats
tracepoint as follows:

ext4_fc_stats: dev 254:32 fc ineligible reasons:
XATTR:0, CROSS_RENAME:0, JOURNAL_FLAG_CHANGE:0, NO_MEM:0, SWAP_BOOT:0,
RESIZE:0, RENAME_DIR:0, FALLOC_RANGE:0, INODE_JOURNAL_DATA:16;
num_commits:6, ineligible: 6, numblks: 3

So in short, this patch guarantees that in case of rename whiteout, we
fall back to full commits.

Amir mentioned that instead of creating a new whiteout object for
every rename, we can create a static whiteout object with irrelevant
nlink. That will make fast commits to not fall back to full
commit. But until this happens, this patch will ensure correctness by
falling back to full commits.

Fixes: 8016e29f ("ext4: fast commit recovery path")
Cc: stable@kernel.org
Signed-off-by: Harshad Shirwadkar <harshadshirwadkar@gmail.com>
Link: https://lore.kernel.org/r/20210316221921.1124955-1-harshadshirwadkar@gmail.comSigned-off-by: Theodore Ts'o <tytso@mit.edu>

When filesystem mount fails because of corrupted filesystem we first
cancel the s_err_report timer reminding fs errors every day and only
then we flush s_error_work. However s_error_work may report another fs
error and re-arm timer thus resulting in timer use-after-free. Fix the
problem by first flushing the work and only after that canceling the
s_err_report timer.

Reported-by: syzbot+628472a2aac693ab0fcd@syzkaller.appspotmail.com
Fixes: 2d01ddc8 ("ext4: save error info to sb through journal if available")
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20210315165906.2175-1-jack@suse.czSigned-off-by: Theodore Ts'o <tytso@mit.edu>

If set_large_file = 1 and errors occur in ext4_handle_dirty_metadata(),
the error code will be overridden, go to out_brelse to avoid this
situation.
Signed-off-by: Shijie Luo <luoshijie1@huawei.com>
Link: https://lore.kernel.org/r/20210312065051.36314-1-luoshijie1@huawei.com
Cc: stable@kernel.org
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

Syzbot report a warning that ext4 may create an empty ea_inode if set
an empty extent attribute to a file on the file system which is no free
blocks left.

  WARNING: CPU: 6 PID: 10667 at fs/ext4/xattr.c:1640 ext4_xattr_set_entry+0x10f8/0x1114 fs/ext4/xattr.c:1640
  ...
  Call trace:
   ext4_xattr_set_entry+0x10f8/0x1114 fs/ext4/xattr.c:1640
   ext4_xattr_block_set+0x1d0/0x1b1c fs/ext4/xattr.c:1942
   ext4_xattr_set_handle+0x8a0/0xf1c fs/ext4/xattr.c:2390
   ext4_xattr_set+0x120/0x1f0 fs/ext4/xattr.c:2491
   ext4_xattr_trusted_set+0x48/0x5c fs/ext4/xattr_trusted.c:37
   __vfs_setxattr+0x208/0x23c fs/xattr.c:177
  ...

Now, ext4 try to store extent attribute into an external inode if
ext4_xattr_block_set() return -ENOSPC, but for the case of store an
empty extent attribute, store the extent entry into the extent
attribute block is enough. A simple reproduce below.

  fallocate test.img -l 1M
  mkfs.ext4 -F -b 2048 -O ea_inode test.img
  mount test.img /mnt
  dd if=/dev/zero of=/mnt/foo bs=2048 count=500
  setfattr -n "user.test" /mnt/foo

Reported-by: syzbot+98b881fdd8ebf45ab4ae@syzkaller.appspotmail.com
Fixes: 9c6e7853 ("ext4: reserve space for xattr entries/names")
Cc: stable@kernel.org
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com>
Link: https://lore.kernel.org/r/20210305120508.298465-1-yi.zhang@huawei.comSigned-off-by: Theodore Ts'o <tytso@mit.edu>

In ext4_rename(), when RENAME_WHITEOUT failed to add new entry into
directory, it ends up dropping new created whiteout inode under the
running transaction. After commit <9b88f9fb> ("ext4: Do not iput inode
under running transaction"), we follow the assumptions that evict() does
not get called from a transaction context but in ext4_rename() it breaks
this suggestion. Although it's not a real problem, better to obey it, so
this patch add inode to orphan list and stop transaction before final
iput().
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com>
Link: https://lore.kernel.org/r/20210303131703.330415-2-yi.zhang@huawei.comSigned-off-by: Theodore Ts'o <tytso@mit.edu>

If we failed to add new entry on rename whiteout, we cannot reset the
old->de entry directly, because the old->de could have moved from under
us during make indexed dir. So find the old entry again before reset is
needed, otherwise it may corrupt the filesystem as below.

  /dev/sda: Entry '00000001' in ??? (12) has deleted/unused inode 15. CLEARED.
  /dev/sda: Unattached inode 75
  /dev/sda: UNEXPECTED INCONSISTENCY; RUN fsck MANUALLY.

Fixes: 6b4b8e6b ("ext4: fix bug for rename with RENAME_WHITEOUT")
Cc: stable@vger.kernel.org
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com>
Link: https://lore.kernel.org/r/20210303131703.330415-1-yi.zhang@huawei.comSigned-off-by: Theodore Ts'o <tytso@mit.edu>

With interrupt force threading all device interrupt handlers are invoked
from kernel threads. Contrary to hard interrupt context the invocation only
disables bottom halfs, but not interrupts. This was an oversight back then
because any code like this will have an issue:

thread(irq_A)
  irq_handler(A)
    spin_lock(&foo->lock);

interrupt(irq_B)
  irq_handler(B)
    spin_lock(&foo->lock);

This has been triggered with networking (NAPI vs. hrtimers) and console
drivers where printk() happens from an interrupt which interrupted the
force threaded handler.

Now people noticed and started to change the spin_lock() in the handler to
spin_lock_irqsave() which affects performance or add IRQF_NOTHREAD to the
interrupt request which in turn breaks RT.

Fix the root cause and not the symptom and disable interrupts before
invoking the force threaded handler which preserves the regular semantics
and the usefulness of the interrupt force threading as a general debugging
tool.

For not RT this is not changing much, except that during the execution of
the threaded handler interrupts are delayed until the handler
returns. Vs. scheduling and softirq processing there is no difference.

For RT kernels there is no issue.

Fixes: 8d32a307 ("genirq: Provide forced interrupt threading")
Reported-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20210317143859.513307808@linutronix.de

Pull RISC-V fixes from Palmer Dabbelt:
 "A handful of fixes for 5.12:

   - fix the SBI remote fence numbers for hypervisor fences, which had
     been transcribed in the wrong order in Linux. These fences are only
     used with the KVM patches applied.

   - fix a whole host of build warnings, these should have no functional
     change.

   - fix init_resources() to prevent an off-by-one error from causing an
     out-of-bounds array reference. This was manifesting during boot on
     vexriscv.

   - ensure the KASAN mappings are visible before proceeding to use
     them"

* tag 'riscv-for-linus-5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: Correct SPARSEMEM configuration
  RISC-V: kasan: Declare kasan_shallow_populate() static
  riscv: Ensure page table writes are flushed when initializing KASAN vmalloc
  RISC-V: Fix out-of-bounds accesses in init_resources()
  riscv: Fix compilation error with Canaan SoC
  ftrace: Fix spelling mistake "disabed" -> "disabled"
  riscv: fix bugon.cocci warnings
  riscv: process: Fix no prototype for arch_dup_task_struct
  riscv: ftrace: Use ftrace_get_regs helper
  riscv: process: Fix no prototype for show_regs
  riscv: syscall_table: Reduce W=1 compilation warnings noise
  riscv: time: Fix no prototype for time_init
  riscv: ptrace: Fix no prototype warnings
  riscv: sbi: Fix comment of __sbi_set_timer_v01
  riscv: irq: Fix no prototype warning
  riscv: traps: Fix no prototype warnings
  RISC-V: correct enum sbi_ext_rfence_fid

Pull cifs fixes from Steve French:
 "Five cifs/smb3 fixes - three for stable, including an important ACL
  fix and security signature fix"

* tag '5.12-rc3-smb3' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: fix allocation size on newly created files
  cifs: warn and fail if trying to use rootfs without the config option
  fs/cifs/: fix misspellings using codespell tool
  cifs: Fix preauth hash corruption
  cifs: update new ACE pointer after populate_new_aces.

Pull SCSI fixes from James Bottomley:
 "Eight fixes, all in drivers, all fairly minor either being fixes in
  error legs, memory leaks on teardown, context errors or semantic
  problems"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: mpt3sas: Do not use GFP_KERNEL in atomic context
  scsi: ufs: ufs-mediatek: Correct operator & -> &&
  scsi: sd_zbc: Update write pointer offset cache
  scsi: lpfc: Fix some error codes in debugfs
  scsi: qla2xxx: Fix broken #endif placement
  scsi: st: Fix a use after free in st_open()
  scsi: myrs: Fix a double free in myrs_cleanup()
  scsi: ibmvfc: Free channel_setup_buf during device tear down