If an async ai command is not running or the ai_mode is 0 the interrupt
routine doesn't do anything other than spew some noise and clear the
interrupt request in the hardware.

Because this driver is manually attached, the "premature interrupt"
check in the interrupt handler should never happen. The interrupt is
only hooked up during the attach and it's released during the detach.

Combine these checks so that the interrupt function exits quick if it
has nothing to handle. Remove the noise.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If an async ai command is not running or the int816_mode is 0 the
interrupt routine doesn't do anything other than spew some noise and
clear the interrupt request in the hardware.

Because this driver is manually attached, the "premature interrupt"
check in the interrupt handler should never happen. The interrupt is
only hooked up during the attach and it's released during the detach.

Combine these checks so that the interrupt function exits quick if it
has nothing to handle. Remove the noise.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Because this driver is manually attached, the "spurious interrupt"
check in the interrupt handler should never happen. The interrupt is
only hooked up during the attach and it's released during the detach.

Leave the check but remove the noise. Also make sure to clear the
interrupt request in the hardware.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When using DMA, the async command (*cancel) operation is delayed until the
current DMA transfer is complete. When the DMA transfer finishes the interrupt
routine detects this and calls the (*cancel) again which should then cancel the
async command.

The current logic does not work when cmd->stop_src == TRIG_NONE. In this case
the (*cancel) function keeps delaying the cancel. The actual DMA does stop
because the DMA handler is not called to setup the next transfer but the
(*cancel) code is never executed.

Rename the 'irq_was_now_closed' flag in the private data to 'ai_cmd_canceled'
to clarify what it is.

Only set the flag in the (*cancel) when a DMA transfer is running and the
async command has not already been canceled. The interrupt routine then does
not need all the extra checks.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This flag in the private data is set when an async command is canceled with
the ai (*cancel) operation. Rename the flag to 'ai_cmd_canceled' to clarify
its use.

Move the check for the flag in the interrupt handler. If the async command
was canceled there is no reason to handle the interrupt. Just clear interrupt
and return.

Also, make sure to clear the interrupt when the device is not attached.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If an async command is not running the (*cancel) function doesn't do
anything. Exit the function early if this is the case.

This allows reducing the indent level in the rest of the function.

Also, move the setting of the 'irq_was_now_closed' to the only place
wher it actually gets left set to 1 and remove the goto.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If an async command is not running the (*cancel) function doesn't do
anything. Exit the function early if this is the case.

This allows reducing the indent level in the rest of the function.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The DMA, FIFO, and EOC interrupt handlers all have common code that
checks for channel dropout when running an async command.

Factor this common code into a helper function.

Only return the sample if the channel is valid. The EOC handler was
previously returning the value then checking for channel dropout.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

To clarify the code, introduce a helper function to read the analog
input data sample from the FIFO and optionally return the channel
that the sample was for. The channel is used to check for dropped
samples.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The A/D FIFO uses two registers to get each analog data sample.
PCL818_FI_DATALO is the LSB of the data and PCL818_FI_DATAHI is
the MSB of the data. The current define for PCL818_FI_DATAHI is
incorrect and results in the LSB getting read twice.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The DMA, FIFO, and EOC interrupt handlers all have common code that
bumps the counters in the private data that keep track of what channel
is being sampled next and when all the data has been sampled.

Factor this common code into a helper function.

Make sure the COMEDI_CB_BLOCK event is set when advancing to the next
channel so that when the comedi_event() is finally called the core will
wake the async_queue to return the analog input data.

Also, make sure the COMEDI_CB_EOS event is set at the completion of each
scan.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Factor out the code that bumps the counters in the private data that keep
track of what channel is being samples next and when all the data has been
sampled.

Don't clear the events in the driver. The comedi core will clear the events
at the end of the comedi_event().

Make sure the COMEDI_CB_BLOCK event is set when advancing to the next
channel so that when the comedi_event() is finally called the core will
wake the async_queue to return the analog input data.

Also, make sure the COMEDI_CB_EOS event is set at the completion of each
scan.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The DMA and EOC interrupt handlers all have common code that bumps the
counters in the private data that keep track of what channel is being
sampled next and when all the data has been sampled.

Factor this common code into a helper function.

Don't clear the events in the driver. The comedi core will clear the events
at the end of the comedi_event().

Make sure the COMEDI_CB_BLOCK event is set when advancing to the next
channel so that when the comedi_event() is finally called the core will
wake the async_queue to return the analog input data.

Also, make sure the COMEDI_CB_EOS event is set at the completion of each
scan.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver only supports async commands if a DMA channel is available. Modify
the subdevice init so that the command support only gets hooked up if we can
do DMA.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

According to the users manual, when using interrupt (non-DMA) transfers
this hardware generates an interrupt at the start of a conversion. This
requires the interrupt routine to busywait until the end-of-conversion.
It appears this was unreliable and interrupt only async command support
was removed at some time. Async command support is still available when
DMA is used.

Remove the unreachable interrupt only handler code.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The interrupt is only generated by the hardware at the completion of
an A/D conversion. Because of this the sanity check to make sure that
the A/D conversion is complete and data is available is probably
unnecessary but it doesn't hurt anything.

The busywait loop is a different issue. Interrupt routines should not
busywait. That's just mean...

Remove the bustwait and use pcl818_ai_eoc() to check for the end-of-
conversion.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The interrupt is only generated by the hardware at the completion of
an A/D conversion. Because of this the sanity check to make sure that
the A/D conversion is complete and data is available is probably
unnecessary but it doesn't hurt anything.

The busywait loop is a different issue. Interrupt routines should not
busywait. That's just mean...

Remove the bustwait and use pcl812_ai_eoc() to check for the end-of-
conversion.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This member of the private data is not used. Remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This member of the private data is only used in the initial dma setup.
Refactor that code to not need it and remove the member.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

To assist in cleaning up the the rest of the driver, factor the initial
dma setup and the next dma buffer setup into helper functions.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

To assist in cleaning up the the rest of the driver, factor the initial
dma setup and the next dma buffer setup into helper functions.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

To assist in cleaning up the the rest of the driver, factor the initial
dma setup and the next dma buffer setup into helper functions.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This member of the private data is not needed. We can check the stop_src
to determine this information:

  neverending_ai -> cmd->stop_src == TRIG_NONE
  !neverending_ai -> cmd->stop_src == TRIG_COUNT
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This member of the private data is not needed. We can check the stop_src
to determine this information:

  ai_neverending -> cmd->stop_src == TRIG_NONE
  !ai_neverending -> cmd->stop_src == TRIG_COUNT
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This member of the private data is not needed. We can check the stop_src
to determine this information:

  ai_neverending -> cmd->stop_src == TRIG_NONE
  !ai_neverending -> cmd->stop_src == TRIG_COUNT
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some of the PCL-818 compatible boards have a FIFO that can be used
when running analog input async commands. This FIFO increased the
resource range used by the driver.

Request the correct resources used by the board even if the FIFO is
not used. This prevents another driver from trying to use the I/O
space.

Modify the attach so that the 'usefifo' flag is only set if we have
and IRQ, the board has a FIFO, and the user wahts to use it.

Fix pcl818_reset() so that the FIFO is always flushed and disabled
if it exists.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This function is a _very_ simplified probe that tried to verify that
the driver is being attached to a PCL-818 compatible board. The function
simply writes some values to specific registers then reads back the
values to see if they are the same.

It's possible that the user could try to attach this driver to a non-
compatible board but the check would still pass depending on the register
map of the board.

Just remove the buggy function to simplify the attach a bit.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This function is a _very_ simplified probe that tried to verify that
the driver is being attached to a PCL-816 compatible board. The function
simply writes some values to specific registers then reads back the
values to see if they are the same.

It's possible that the user could try to attach this driver to a non-
compatible board but the check would still pass depending on the register
map of the board.

Just remove the buggy function to simplify the attach a bit.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch simplifies and cleans up the dgap_init_module function. It also fixes
a possible double free condition as a result pci_unregister_driver possibly
being called twice.
Signed-off-by: Mark Hounschell <markh@compro.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch removes printks associated with sysfile creation
and changes the dgap_create_driver_sysfiles function to return
an int so we can check for errors in the sysfile creation
process.

The printk's were flagged by checkpatch but then
driver_create_file was flagged by checkpatch for
not checking its return. So we remove the printk's
and check the return of driver_create_file.
Signed-off-by: Mark Hounschell <markh@compro.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch removes more dead code and code associated
with that dead code. The from_user variable in the
dgap_tty_write function was never true. The code under
its test was never being executed. So variables and
functions supporting only that code are also dead.
Signed-off-by: Mark Hounschell <markh@compro.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes a few 80+ char lines as reported by checkpatch
Signed-off-by: Mark Hounschell <markh@compro.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes a few 80+ char lines as reported by checkpatch
Signed-off-by: Mark Hounschell <markh@compro.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes a few 80+ char lines as reported by checkpatch
Signed-off-by: Mark Hounschell <markh@compro.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes a few of the many 80+ character lines
as reported by checkpatch
Signed-off-by: Mark Hounschell <markh@compro.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes a checkpatch warning for
suspect code indent for conditional statements
Signed-off-by: Mark Hounschell <markh@compro.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes a checkpatch warning for not checking
the return value of sscanf.
Signed-off-by: Mark Hounschell <markh@compro.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch removes the rawreadok module param and sysfs var
previously used to enable flip buffer bypass. Code dealing
with that param was removed previously.
Signed-off-by: Mark Hounschell <markh@compro.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dgap_global_lock is no longer required. This patch
removes it.
Signed-off-by: Mark Hounschell <markh@compro.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We should not remove a sysfs group we failed to create
Signed-off-by: Mark Hounschell <markh@compro.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>