Both versions of the CPSW driver declare a CPSW_HEADROOM_NA macro that
takes NET_IP_ALIGN into account, but fail to use it appropriately when
storing incoming packets in memory. This results in the IPv4 source and
destination addresses to appear misaligned in memory, which causes
aligment faults that need to be fixed up in software.

So let's switch from CPSW_HEADROOM to CPSW_HEADROOM_NA where needed.
This gets rid of any alignment faults on the RX path on a Beaglebone
White.

Fixes: 9ed4050c ("net: ethernet: ti: cpsw: add XDP support")
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Syzbot detected a NULL pointer dereference of nfc_llcp_sock->dev pointer
(which is a 'struct nfc_dev *') with calls to llcp_sock_sendmsg() after
a failed llcp_sock_bind(). The message being sent is a SOCK_DGRAM.

KASAN report:

  BUG: KASAN: null-ptr-deref in nfc_alloc_send_skb+0x2d/0xc0
  Read of size 4 at addr 00000000000005c8 by task llcp_sock_nfc_a/899

  CPU: 5 PID: 899 Comm: llcp_sock_nfc_a Not tainted 5.16.0-rc6-next-20211224-00001-gc6437fbf18b0 #125
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-2 04/01/2014
  Call Trace:
   <TASK>
   dump_stack_lvl+0x45/0x59
   ? nfc_alloc_send_skb+0x2d/0xc0
   __kasan_report.cold+0x117/0x11c
   ? mark_lock+0x480/0x4f0
   ? nfc_alloc_send_skb+0x2d/0xc0
   kasan_report+0x38/0x50
   nfc_alloc_send_skb+0x2d/0xc0
   nfc_llcp_send_ui_frame+0x18c/0x2a0
   ? nfc_llcp_send_i_frame+0x230/0x230
   ? __local_bh_enable_ip+0x86/0xe0
   ? llcp_sock_connect+0x470/0x470
   ? llcp_sock_connect+0x470/0x470
   sock_sendmsg+0x8e/0xa0
   ____sys_sendmsg+0x253/0x3f0
   ...

The issue was visible only with multiple simultaneous calls to bind() and
sendmsg(), which resulted in most of the bind() calls to fail.  The
bind() was failing on checking if there is available WKS/SDP/SAP
(respective bit in 'struct nfc_llcp_local' fields).  When there was no
available WKS/SDP/SAP, the bind returned error but the sendmsg() to such
socket was able to trigger mentioned NULL pointer dereference of
nfc_llcp_sock->dev.

The code looks simply racy and currently it protects several paths
against race with checks for (!nfc_llcp_sock->local) which is NULL-ified
in error paths of bind().  The llcp_sock_sendmsg() did not have such
check but called function nfc_llcp_send_ui_frame() had, although not
protected with lock_sock().

Therefore the race could look like (same socket is used all the time):
  CPU0                                     CPU1
  ====                                     ====
  llcp_sock_bind()
  - lock_sock()
    - success
  - release_sock()
  - return 0
                                           llcp_sock_sendmsg()
                                           - lock_sock()
                                           - release_sock()
  llcp_sock_bind(), same socket
  - lock_sock()
    - error
                                           - nfc_llcp_send_ui_frame()
                                             - if (!llcp_sock->local)
    - llcp_sock->local = NULL
    - nfc_put_device(dev)
                                             - dereference llcp_sock->dev
  - release_sock()
  - return -ERRNO

The nfc_llcp_send_ui_frame() checked llcp_sock->local outside of the
lock, which is racy and ineffective check.  Instead, its caller
llcp_sock_sendmsg(), should perform the check inside lock_sock().

Reported-and-tested-by: syzbot+7f23bcddf626e0593a39@syzkaller.appspotmail.com
Fixes: b874dec2 ("NFC: Implement LLCP connection less Tx path")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Robert Hancock says:

====================
Xilinx axienet fixes

Various fixes for the Xilinx AXI Ethernet driver.

Changed since v2:
-added Reviewed-by tags, added some explanation to commit
messages, no code changes

Changed since v1:
-corrected a Fixes tag to point to mainline commit
-split up reset changes into 3 patches
-added ratelimit on netdev_warn in TX busy case
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

With previous changes to make the driver handle the TX ring size more
correctly, the default TX ring size of 64 appears to significantly
bottleneck TX performance to around 600 Mbps on a 1 Gbps link on ZynqMP.
Increasing this to 128 seems to bring performance up to near line rate and
shouldn't cause excess bufferbloat (this driver doesn't yet support modern
byte-based queue management).

Fixes: 8a3b7a25 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Network driver documentation indicates we should be avoiding returning
NETDEV_TX_BUSY from ndo_start_xmit in normal cases, since it requires
the packets to be requeued. Instead the queue should be stopped after
a packet is added to the TX ring when there may not be enough room for an
additional one. Also, when TX ring entries are completed, we should only
wake the queue if we know there is room for another full maximally
fragmented packet.

Print a warning if there is insufficient space at the start of start_xmit,
since this should no longer happen.

Combined with increasing the default TX ring size (in a subsequent
patch), this appears to recover the TX performance lost by previous changes
to actually manage the TX ring state properly.

Fixes: 8a3b7a25 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The check for the number of available TX ring slots was off by 1 since a
slot is required for the skb header as well as each fragment. This could
result in overwriting a TX ring slot that was still in use.

Fixes: 8a3b7a25 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The check for whether a TX ring slot was available was incorrect,
since a slot which had been loaded with transmit data but the device had
not started transmitting would be treated as available, potentially
causing non-transmitted slots to be overwritten. The control field in
the descriptor should be checked, rather than the status field (which may
only be updated when the device completes the entry).

Fixes: 8a3b7a25 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver will not work properly if the TX ring size is set to below
MAX_SKB_FRAGS + 1 since it needs to hold at least one full maximally
fragmented packet in the TX ring. Limit setting the ring size to below
this value.

Fixes: 8b09ca82 ("net: axienet: Make RX/TX ring sizes configurable")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver was missing some required memory barriers:

Use dma_rmb to ensure we see all updates to the descriptor after we see
that an entry has been completed.

Use wmb and rmb to avoid stale descriptor status between the TX path and
TX complete IRQ path.

Fixes: 8a3b7a25 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In some cases where the Xilinx Ethernet core was used in 1000Base-X or
SGMII modes, which use the internal PCS/PMA PHY, and the MGT
transceiver clock source for the PCS was not running at the time the
FPGA logic was loaded, the core would come up in a state where the
PCS could not be found on the MDIO bus. To fix this, the Ethernet core
(including the PCS) should be reset after enabling the clocks, prior to
attempting to access the PCS using of_mdio_find_device.

Fixes: 1a025560 (net: axienet: Properly handle PCS/PMA PHY for 1000BaseX mode)
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

When resetting the device, wait for the PhyRstCmplt bit to be set
in the interrupt status register before continuing initialization, to
ensure that the core is actually ready. When using an external PHY, this
also ensures we do not start trying to access the PHY while it is still
in reset. The PHY reset is initiated by the core reset which is
triggered just above, but remains asserted for 5ms after the core is
reset according to the documentation.

The MgtRdy bit could also be waited for, but unfortunately when using
7-series devices, the bit does not appear to work as documented (it
seems to behave as some sort of link state indication and not just an
indication the transceiver is ready) so it can't really be relied on for
this purpose.

Fixes: 8a3b7a25 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The previous timeout of 1ms was too short to handle some cases where the
core is reset just after the input clocks were started, which will
be introduced in an upcoming patch. Increase the timeout to 50ms. Also
simplify the reset timeout checking to use read_poll_timeout.

Fixes: 8a3b7a25 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf 2022-01-19

We've added 12 non-merge commits during the last 8 day(s) which contain
a total of 12 files changed, 262 insertions(+), 64 deletions(-).

The main changes are:

1) Various verifier fixes mainly around register offset handling when
   passed to helper functions, from Daniel Borkmann.

2) Fix XDP BPF link handling to assert program type,
   from Toke Høiland-Jørgensen.

3) Fix regression in mount parameter handling for BPF fs,
   from Yafang Shao.

4) Fix incorrect integer literal when marking scratched stack slots
   in verifier, from Christy Lee.

* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
  bpf, selftests: Add ringbuf memory type confusion test
  bpf, selftests: Add various ringbuf tests with invalid offset
  bpf: Fix ringbuf memory type confusion when passing to helpers
  bpf: Fix out of bounds access for ringbuf helpers
  bpf: Generally fix helper register offset check
  bpf: Mark PTR_TO_FUNC register initially with zero offset
  bpf: Generalize check_ctx_reg for reuse with other types
  bpf: Fix incorrect integer literal used for marking scratched stack.
  bpf/selftests: Add check for updating XDP bpf_link with wrong program type
  bpf/selftests: convert xdp_link test to ASSERT_* macros
  xdp: check prog type before updating BPF link
  bpf: Fix mount source show for bpffs
====================

Link: https://lore.kernel.org/r/20220119011825.9082-1-daniel@iogearbox.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add two tests, one which asserts that ring buffer memory can be passed to
other helpers for populating its entry area, and another one where verifier
rejects different type of memory passed to bpf_ringbuf_submit().
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>

Assert that the verifier is rejecting invalid offsets on the ringbuf entries:

  # ./test_verifier | grep ring
  #947/u ringbuf: invalid reservation offset 1 OK
  #947/p ringbuf: invalid reservation offset 1 OK
  #948/u ringbuf: invalid reservation offset 2 OK
  #948/p ringbuf: invalid reservation offset 2 OK
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>

The bpf_ringbuf_submit() and bpf_ringbuf_discard() have ARG_PTR_TO_ALLOC_MEM
in their bpf_func_proto definition as their first argument, and thus both expect
the result from a prior bpf_ringbuf_reserve() call which has a return type of
RET_PTR_TO_ALLOC_MEM_OR_NULL.

While the non-NULL memory from bpf_ringbuf_reserve() can be passed to other
helpers, the two sinks (bpf_ringbuf_submit(), bpf_ringbuf_discard()) right now
only enforce a register type of PTR_TO_MEM.

This can lead to potential type confusion since it would allow other PTR_TO_MEM
memory to be passed into the two sinks which did not come from bpf_ringbuf_reserve().

Add a new MEM_ALLOC composable type attribute for PTR_TO_MEM, and enforce that:

 - bpf_ringbuf_reserve() returns NULL or PTR_TO_MEM | MEM_ALLOC
 - bpf_ringbuf_submit() and bpf_ringbuf_discard() only take PTR_TO_MEM | MEM_ALLOC
   but not plain PTR_TO_MEM arguments via ARG_PTR_TO_ALLOC_MEM
 - however, other helpers might treat PTR_TO_MEM | MEM_ALLOC as plain PTR_TO_MEM
   to populate the memory area when they use ARG_PTR_TO_{UNINIT_,}MEM in their
   func proto description

Fixes: 457f4436 ("bpf: Implement BPF ring buffer and verifier support for it")
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>

Both bpf_ringbuf_submit() and bpf_ringbuf_discard() have ARG_PTR_TO_ALLOC_MEM
in their bpf_func_proto definition as their first argument. They both expect
the result from a prior bpf_ringbuf_reserve() call which has a return type of
RET_PTR_TO_ALLOC_MEM_OR_NULL.

Meaning, after a NULL check in the code, the verifier will promote the register
type in the non-NULL branch to a PTR_TO_MEM and in the NULL branch to a known
zero scalar. Generally, pointer arithmetic on PTR_TO_MEM is allowed, so the
latter could have an offset.

The ARG_PTR_TO_ALLOC_MEM expects a PTR_TO_MEM register type. However, the non-
zero result from bpf_ringbuf_reserve() must be fed into either bpf_ringbuf_submit()
or bpf_ringbuf_discard() but with the original offset given it will then read
out the struct bpf_ringbuf_hdr mapping.

The verifier missed to enforce a zero offset, so that out of bounds access
can be triggered which could be used to escalate privileges if unprivileged
BPF was enabled (disabled by default in kernel).

Fixes: 457f4436 ("bpf: Implement BPF ring buffer and verifier support for it")
Reported-by: <tr3e.wang@gmail.com> (SecCoder Security Lab)
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>

Right now the assertion on check_ptr_off_reg() is only enforced for register
types PTR_TO_CTX (and open coded also for PTR_TO_BTF_ID), however, this is
insufficient since many other PTR_TO_* register types such as PTR_TO_FUNC do
not handle/expect register offsets when passed to helper functions.

Given this can slip-through easily when adding new types, make this an explicit
allow-list and reject all other current and future types by default if this is
encountered.

Also, extend check_ptr_off_reg() to handle PTR_TO_BTF_ID as well instead of
duplicating it. For PTR_TO_BTF_ID, reg->off is used for BTF to match expected
BTF ids if struct offset is used. This part still needs to be allowed, but the
dynamic off from the tnum must be rejected.

Fixes: 69c087ba ("bpf: Add bpf_for_each_map_elem() helper")
Fixes: eaa6bcb7 ("bpf: Introduce bpf_per_cpu_ptr()")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>

Similar as with other pointer types where we use ldimm64, clear the register
content to zero first, and then populate the PTR_TO_FUNC type and subprogno
number. Currently this is not done, and leads to reuse of stale register
tracking data.

Given for special ldimm64 cases we always clear the register offset, make it
common for all cases, so it won't be forgotten in future.

Fixes: 69c087ba ("bpf: Add bpf_for_each_map_elem() helper")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>

Generalize the check_ctx_reg() helper function into a more generic named one
so that it can be reused for other register types as well to check whether
their offset is non-zero. No functional change.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>

When under stress, cleanup_net() can have to dismantle
netns in big numbers. ops_exit_list() currently calls
many helpers [1] that have no schedule point, and we can
end up with soft lockups, particularly on hosts
with many cpus.

Even for moderate amount of netns processed by cleanup_net()
this patch avoids latency spikes.

[1] Some of these helpers like fib_sync_up() and fib_sync_down_dev()
are very slow because net/ipv4/fib_semantics.c uses host-wide hash tables,
and ifindex is used as the only input of two hash functions.
    ifindexes tend to be the same for all netns (lo.ifindex==1 per instance)
    This will be fixed in a separate patch.

Fixes: 72ad937a ("net: Add support for batching network namespace cleanups")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 7cfa9c92 ("net: sfp: avoid power switch on address-change
modules") unintetionally changed the semantics for high power modules
without the digital diagnostics monitoring. We repeatedly attempt to
read the power status from the non-existing 0xa2 address in a futile
hope this failure is temporary:

[    8.856051] sfp sfp-eth3: module NTT              0000000000000000 rev 0000  sn 0000000000000000 dc 160408
[    8.865843] mvpp2 f4000000.ethernet eth3: switched to inband/1000base-x link mode
[    8.873469] sfp sfp-eth3: Failed to read EEPROM: -5
[    8.983251] sfp sfp-eth3: Failed to read EEPROM: -5
[    9.103250] sfp sfp-eth3: Failed to read EEPROM: -5

We previosuly assumed such modules were powered up in the correct mode,
continuing without further configuration as long as the required power
class was supported by the host.

Restore this behaviour, while preserving the intent of subsequent
patches to avoid the "Address Change Sequence not supported" warning
if we are not going to be accessing the DDM address.

Fixes: 7cfa9c92 ("net: sfp: avoid power switch on address-change modules")
Reported-by: 照山周一郎 <teruyama@springboard-inc.jp>
Tested-by: 照山周一郎 <teruyama@springboard-inc.jp>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Gal Pressman says:

====================
net: Couple of skb memory leak fixes

As discussed in:
https://lore.kernel.org/netdev/20220102081253.9123-1-gal@nvidia.com/

These are the two followup suggestions from Eric and Jakub.
Patch #1 adds a sk_defer_free_flush() call to the kTLS splice_read
handler.
Patch #2 verifies the defer list is empty on socket destroy, and calls a
defer free flush as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The cited Fixes patch moved to a deferred skb approach where the skbs
are not freed immediately under the socket lock.  Add a WARN_ON_ONCE()
to verify the deferred list is empty on socket destroy, and empty it to
prevent potential memory leaks.

Fixes: f35f8219 ("tcp: defer skb freeing after socket lock is released")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is a followup to
commit ffef737f ("net/tls: Fix skb memory leak when running kTLS traffic")

Which was missing another sk_defer_free_flush() call in
tls_sw_splice_read().

Fixes: f35f8219 ("tcp: defer skb freeing after socket lock is released")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the blamed commit, the call to the function
switchdev_bridge_port_offload was passing the wrong argument for
atomic_nb. It was ocelot_netdevice_nb instead of ocelot_swtchdev_nb.
This patch fixes this issue.

Fixes: 4e51bf44 ("net: bridge: move the switchdev object replay helpers to "push" mode")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Wrong hash sends single stream to multiple output interfaces.

The offset calculation was relative to skb->head, fix it to be relative
to skb->data.

Fixes: a815bde5 ("net, bonding: Refactor bond_xmit_hash for use with
xdp_buff")
Reviewed-by: Jussi Maki <joamaki@gmail.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Moshe Tal <moshet@nvidia.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A hung_task is observed when removing SMC-R devices. Suppose that
a link group has two active links(lnk_A, lnk_B) associated with two
different SMC-R devices(dev_A, dev_B). When dev_A is removed, the
link group will be removed from smc_lgr_list and added into
lgr_linkdown_list. lnk_A will be cleared and smcibdev(A)->lnk_cnt
will reach to zero. However, when dev_B is removed then, the link
group can't be found in smc_lgr_list and lnk_B won't be cleared,
making smcibdev->lnk_cnt never reaches zero, which causes a hung_task.

This patch fixes this issue by restoring the implementation of
smc_smcr_terminate_all() to what it was before commit 349d4312
("net/smc: fix kernel panic caused by race of smc_sock"). The original
implementation also satisfies the intention that make sure QP destroy
earlier than CQ destroy because we will always wait for smcibdev->lnk_cnt
reaches zero, which guarantees QP has been destroyed.

Fixes: 349d4312 ("net/smc: fix kernel panic caused by race of smc_sock")
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the past, free_fib_info() was supposed to be called
under RTNL protection.

This eventually was no longer the case.

Instead of enforcing RTNL it seems we simply can
move fib_info_cnt changes to occur when fib_info_lock
is held.

v2: David Laight suggested to update fib_info_cnt
only when an entry is added/deleted to/from the hash table,
as fib_info_cnt is used to make sure hash table size
is optimal.

BUG: KCSAN: data-race in fib_create_info / free_fib_info

write to 0xffffffff86e243a0 of 4 bytes by task 26429 on cpu 0:
 fib_create_info+0xe78/0x3440 net/ipv4/fib_semantics.c:1428
 fib_table_insert+0x148/0x10c0 net/ipv4/fib_trie.c:1224
 fib_magic+0x195/0x1e0 net/ipv4/fib_frontend.c:1087
 fib_add_ifaddr+0xd0/0x2e0 net/ipv4/fib_frontend.c:1109
 fib_netdev_event+0x178/0x510 net/ipv4/fib_frontend.c:1466
 notifier_call_chain kernel/notifier.c:83 [inline]
 raw_notifier_call_chain+0x53/0xb0 kernel/notifier.c:391
 __dev_notify_flags+0x1d3/0x3b0
 dev_change_flags+0xa2/0xc0 net/core/dev.c:8872
 do_setlink+0x810/0x2410 net/core/rtnetlink.c:2719
 rtnl_group_changelink net/core/rtnetlink.c:3242 [inline]
 __rtnl_newlink net/core/rtnetlink.c:3396 [inline]
 rtnl_newlink+0xb10/0x13b0 net/core/rtnetlink.c:3506
 rtnetlink_rcv_msg+0x745/0x7e0 net/core/rtnetlink.c:5571
 netlink_rcv_skb+0x14e/0x250 net/netlink/af_netlink.c:2496
 rtnetlink_rcv+0x18/0x20 net/core/rtnetlink.c:5589
 netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
 netlink_unicast+0x5fc/0x6c0 net/netlink/af_netlink.c:1345
 netlink_sendmsg+0x726/0x840 net/netlink/af_netlink.c:1921
 sock_sendmsg_nosec net/socket.c:704 [inline]
 sock_sendmsg net/socket.c:724 [inline]
 ____sys_sendmsg+0x39a/0x510 net/socket.c:2409
 ___sys_sendmsg net/socket.c:2463 [inline]
 __sys_sendmsg+0x195/0x230 net/socket.c:2492
 __do_sys_sendmsg net/socket.c:2501 [inline]
 __se_sys_sendmsg net/socket.c:2499 [inline]
 __x64_sys_sendmsg+0x42/0x50 net/socket.c:2499
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

read to 0xffffffff86e243a0 of 4 bytes by task 31505 on cpu 1:
 free_fib_info+0x35/0x80 net/ipv4/fib_semantics.c:252
 fib_info_put include/net/ip_fib.h:575 [inline]
 nsim_fib4_rt_destroy drivers/net/netdevsim/fib.c:294 [inline]
 nsim_fib4_rt_replace drivers/net/netdevsim/fib.c:403 [inline]
 nsim_fib4_rt_insert drivers/net/netdevsim/fib.c:431 [inline]
 nsim_fib4_event drivers/net/netdevsim/fib.c:461 [inline]
 nsim_fib_event drivers/net/netdevsim/fib.c:881 [inline]
 nsim_fib_event_work+0x15ca/0x2cf0 drivers/net/netdevsim/fib.c:1477
 process_one_work+0x3fc/0x980 kernel/workqueue.c:2298
 process_scheduled_works kernel/workqueue.c:2361 [inline]
 worker_thread+0x7df/0xa70 kernel/workqueue.c:2447
 kthread+0x2c7/0x2e0 kernel/kthread.c:327
 ret_from_fork+0x1f/0x30

value changed: 0x00000d2d -> 0x00000d2e

Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 31505 Comm: kworker/1:21 Not tainted 5.16.0-rc6-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: events nsim_fib_event_work

Fixes: 48bb9eb4 ("netdevsim: fib: Add dummy implementation for FIB offload")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The declaration of smc_wr_tx_dismiss_slots() is unused.
So remove it.

Fixes: 349d4312 ("net/smc: fix kernel panic caused by race of smc_sock")
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Reviewed-by: Dust Li <dust.li@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In pci_generic.c there is a 'mru_default' in struct mhi_pci_dev_info.
This value shall be used for whole mhi if it's given a value for a specific product.
But in function mhi_net_rx_refill_work(), it's still using hard code value MHI_DEFAULT_MRU.
'mru_default' shall have higher priority than MHI_DEFAULT_MRU.
And after checking, this change could help fix a data connection lost issue.

Fixes: 5c2c8531 ("bus: mhi: pci-generic: configurable network interface MRU")
Signed-off-by: Shujun Wang <wsj20369@163.com>
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Existing genphy_loopback() is not applicable for Marvell PHY. Besides
configuring bit-6 and bit-13 in Page 0 Register 0 (Copper Control
Register), it is also required to configure same bits  in Page 2
Register 21 (MAC Specific Control Register 2) according to speed of
the loopback is operating.

Tested working on Marvell88E1510 PHY for all speeds (1000/100/10Mbps).

FIXME: Based on trial and error test, it seem 1G need to have delay between
soft reset and loopback enablement.

Fixes: 014068dc ("net: phy: genphy_loopback: add link speed configuration")
Cc: <stable@vger.kernel.org> # 5.15.x
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A dma_request_chan() call is hidden in emac_configure_dma().
It must be released in the probe if an error occurs, as already done in
the remove function.

Add the corresponding dma_release_channel() call.

Fixes: 47869e82 ("sun4i-emac.c: add dma support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clang static analysis reports this problem
mtk_eth_soc.c:394:7: warning: Branch condition evaluates
  to a garbage value
                if (err)
                    ^~~

err is not initialized and only conditionally set.
So intitialize err.

Fixes: 7e538372 ("net: ethernet: mediatek: Re-add support SGMII")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The following command sequence:

tc qdisc del dev swp0 clsact
tc qdisc add dev swp0 ingress_block 1 clsact
tc qdisc add dev swp1 ingress_block 1 clsact
tc filter add block 1 flower action drop
tc qdisc del dev swp0 clsact

produces the following NPD:

Unable to handle kernel NULL pointer dereference at virtual address 0000000000000014
pc : vcap_entry_set+0x14/0x70
lr : ocelot_vcap_filter_del+0x198/0x234
Call trace:
 vcap_entry_set+0x14/0x70
 ocelot_vcap_filter_del+0x198/0x234
 ocelot_cls_flower_destroy+0x94/0xe4
 felix_cls_flower_del+0x70/0x84
 dsa_slave_setup_tc_block_cb+0x13c/0x60c
 dsa_slave_setup_tc_block_cb_ig+0x20/0x30
 tc_setup_cb_reoffload+0x44/0x120
 fl_reoffload+0x280/0x320
 tcf_block_playback_offloads+0x6c/0x184
 tcf_block_unbind+0x80/0xe0
 tcf_block_setup+0x174/0x214
 tcf_block_offload_cmd.isra.0+0x100/0x13c
 tcf_block_offload_unbind+0x5c/0xa0
 __tcf_block_put+0x54/0x174
 tcf_block_put_ext+0x5c/0x74
 clsact_destroy+0x40/0x60
 qdisc_destroy+0x4c/0x150
 qdisc_put+0x70/0x90
 qdisc_graft+0x3f0/0x4c0
 tc_get_qdisc+0x1cc/0x364
 rtnetlink_rcv_msg+0x124/0x340

The reason is that the driver isn't prepared to receive two tc filters
with the same cookie. It unconditionally creates a new struct
ocelot_vcap_filter for each tc filter, and it adds all filters with the
same identifier (cookie) to the ocelot_vcap_block.

The problem is here, in ocelot_vcap_filter_del():

	/* Gets index of the filter */
	index = ocelot_vcap_block_get_filter_index(block, filter);
	if (index < 0)
		return index;

	/* Delete filter */
	ocelot_vcap_block_remove_filter(ocelot, block, filter);

	/* Move up all the blocks over the deleted filter */
	for (i = index; i < block->count; i++) {
		struct ocelot_vcap_filter *tmp;

		tmp = ocelot_vcap_block_find_filter_by_index(block, i);
		vcap_entry_set(ocelot, i, tmp);
	}

what will happen is ocelot_vcap_block_get_filter_index() will return the
index (@index) of the first filter found with that cookie. This is _not_
the index of _this_ filter, but the other one with the same cookie,
because ocelot_vcap_filter_equal() gets fooled.

Then later, ocelot_vcap_block_remove_filter() is coded to remove all
filters that are ocelot_vcap_filter_equal() with the passed @filter.
So unexpectedly, both filters get deleted from the list.

Then ocelot_vcap_filter_del() will attempt to move all the other filters
up, again finding them by index (@i). The block count is 2, @index was 0,
so it will attempt to move up filter @i=0 and @i=1. It assigns tmp =
ocelot_vcap_block_find_filter_by_index(block, i), which is now a NULL
pointer because ocelot_vcap_block_remove_filter() has removed more than
one filter.

As far as I can see, this problem has been there since the introduction
of tc offload support, however I cannot test beyond the blamed commit
due to hardware availability. In any case, any fix cannot be backported
that far, due to lots of changes to the code base.

Therefore, let's go for the correct solution, which is to not call
ocelot_vcap_filter_add() and ocelot_vcap_filter_del(), unless the filter
is actually unique and not shared. For the shared filters, we should
just modify the ingress port mask and call ocelot_vcap_filter_replace(),
a function introduced by commit 95706be1 ("net: mscc: ocelot: create
a function that replaces an existing VCAP filter"). This way,
block->rules will only contain filters with unique cookies, by design.

Fixes: 07d985ee ("net: dsa: felix: Wire up the ocelot cls_flower methods")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

wait_for_unix_gc() reads unix_tot_inflight & gc_in_progress
without synchronization.

Adds READ_ONCE()/WRITE_ONCE() and their associated comments
to better document the intent.

BUG: KCSAN: data-race in unix_inflight / wait_for_unix_gc

write to 0xffffffff86e2b7c0 of 4 bytes by task 9380 on cpu 0:
 unix_inflight+0x1e8/0x260 net/unix/scm.c:63
 unix_attach_fds+0x10c/0x1e0 net/unix/scm.c:121
 unix_scm_to_skb net/unix/af_unix.c:1674 [inline]
 unix_dgram_sendmsg+0x679/0x16b0 net/unix/af_unix.c:1817
 unix_seqpacket_sendmsg+0xcc/0x110 net/unix/af_unix.c:2258
 sock_sendmsg_nosec net/socket.c:704 [inline]
 sock_sendmsg net/socket.c:724 [inline]
 ____sys_sendmsg+0x39a/0x510 net/socket.c:2409
 ___sys_sendmsg net/socket.c:2463 [inline]
 __sys_sendmmsg+0x267/0x4c0 net/socket.c:2549
 __do_sys_sendmmsg net/socket.c:2578 [inline]
 __se_sys_sendmmsg net/socket.c:2575 [inline]
 __x64_sys_sendmmsg+0x53/0x60 net/socket.c:2575
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

read to 0xffffffff86e2b7c0 of 4 bytes by task 9375 on cpu 1:
 wait_for_unix_gc+0x24/0x160 net/unix/garbage.c:196
 unix_dgram_sendmsg+0x8e/0x16b0 net/unix/af_unix.c:1772
 unix_seqpacket_sendmsg+0xcc/0x110 net/unix/af_unix.c:2258
 sock_sendmsg_nosec net/socket.c:704 [inline]
 sock_sendmsg net/socket.c:724 [inline]
 ____sys_sendmsg+0x39a/0x510 net/socket.c:2409
 ___sys_sendmsg net/socket.c:2463 [inline]
 __sys_sendmmsg+0x267/0x4c0 net/socket.c:2549
 __do_sys_sendmmsg net/socket.c:2578 [inline]
 __se_sys_sendmmsg net/socket.c:2575 [inline]
 __x64_sys_sendmmsg+0x53/0x60 net/socket.c:2575
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

value changed: 0x00000002 -> 0x00000004

Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 9375 Comm: syz-executor.1 Not tainted 5.16.0-rc7-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Fixes: 9915672d ("af_unix: limit unix_tot_inflight")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20220114164328.2038499-1-eric.dumazet@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

If the device is PCI based like intel-eth-pci, pm_runtime_enable() is
already called by pci_pm_init().

So only pm_runtime_enable() when it's not already enabled.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

platform_get_irq() returns negative error number instead 0 on failure.
And the doc of platform_get_irq() provides a usage example:

    int irq = platform_get_irq(pdev, 0);
    if (irq < 0)
        return irq;

Fix the check of return value to catch errors correctly.

Fixes: 11597885 ("i825xx: Move the Intel 82586/82593/82596 based drivers")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit adeef3e3 ("net: constify netdev->dev_addr") the bmac
driver no longer builds with the following errors (pmac32_defconfig):

  linux/drivers/net/ethernet/apple/bmac.c: In function ‘bmac_probe’:
  linux/drivers/net/ethernet/apple/bmac.c:1287:20: error: assignment of read-only location ‘*(dev->dev_addr + (sizetype)j)’
   1287 |   dev->dev_addr[j] = rev ? bitrev8(addr[j]): addr[j];
        |                    ^

Fix it by making the modifications to a local macaddr variable and then
passing that to eth_hw_addr_set().

We don't use the existing addr variable because the bitrev8() would
mutate it, but it is already used unreversed later in the function.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit adeef3e3 ("net: constify netdev->dev_addr") the mace
driver no longer builds with various errors (pmac32_defconfig):

  linux/drivers/net/ethernet/apple/mace.c: In function ‘mace_probe’:
  linux/drivers/net/ethernet/apple/mace.c:170:20: error: assignment of read-only location ‘*(dev->dev_addr + (sizetype)j)’
    170 |   dev->dev_addr[j] = rev ? bitrev8(addr[j]): addr[j];
        |                    ^
  linux/drivers/net/ethernet/apple/mace.c: In function ‘mace_reset’:
  linux/drivers/net/ethernet/apple/mace.c:349:32: warning: passing argument 2 of ‘__mace_set_address’ discards ‘const’ qualifier from pointer target type
    349 |     __mace_set_address(dev, dev->dev_addr);
        |                             ~~~^~~~~~~~~~
  linux/drivers/net/ethernet/apple/mace.c:93:62: note: expected ‘void *’ but argument is of type ‘const unsigned char *’
     93 | static void __mace_set_address(struct net_device *dev, void *addr);
        |                                                        ~~~~~~^~~~
  linux/drivers/net/ethernet/apple/mace.c: In function ‘__mace_set_address’:
  linux/drivers/net/ethernet/apple/mace.c:388:36: error: assignment of read-only location ‘*(dev->dev_addr + (sizetype)i)’
    388 |  out_8(&mb->padr, dev->dev_addr[i] = p[i]);
        |                                    ^

Fix it by making the modifications to a local macaddr variable and then
passing that to eth_hw_addr_set(), as well as adding some missing const
qualifiers.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>