This will allow adding batch flushing on top.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch split out XDP logic into a single function. This make it to
be reused by XDP batching path in the following patch.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we're sure not to go native XDP, there's no need for several things
like bh and rcu stuffs. So this patch introduces a helper to build skb
and hold page refcnt. When we found we will go through skb path, build
skb directly.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There's no need to duplicate page get logic in each action. So this
patch tries to get page and calculate the offset before processing XDP
actions (except for XDP_DROP), and undo them when meet errors (we
don't care the performance on errors). This will be used for factoring
out XDP logic.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch move the bh enabling a little bit earlier, this will be
used for factoring out the core XDP logic of tuntap.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch introduces a new sock flag - SOCK_XDP. This will be used
for notifying the upper layer that XDP program is attached on the
lower socket, and requires for extra headroom.

TUN will be the first user.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

llc_sap_close() is called by llc_sap_put() which
could be called in BH context in llc_rcv(). We can't
block in BH.

There is no reason to block it here, kfree_rcu() should
be sufficient.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The socket option will be enabled by default to ensure current behaviour
is not changed. This is the same for the IPv4 version.

A socket bound to in6addr_any and a specific port will receive all traffic
on that port. Analogue to IP_MULTICAST_ALL, disable this behaviour, if
one or more multicast groups were joined (using said socket) and only
pass on multicast traffic from groups, which were explicitly joined via
this socket.

Without this option disabled a socket (system even) joined to multiple
multicast groups is very hard to get right. Filtering by destination
address has to take place in user space to avoid receiving multicast
traffic from other multicast groups, which might have traffic on the same
port.

The extension of the IP_MULTICAST_ALL socketoption to just apply to ipv6,
too, is not done to avoid changing the behaviour of current applications.
Signed-off-by: Andre Naujoks <nautsch2@gmail.com>
Acked-By: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hauke Mehrtens says:

====================
Add support for Lantiq / Intel vrx200 network

This adds basic support for the GSWIP (Gigabit Switch) found in the
VRX200 SoC.
There are different versions of this IP core used in different SoCs, but
this driver was currently only tested on the VRX200 SoC line, for other
SoCs this driver probably need some adoptions to work.

I also plan to add Layer 2 offloading to the DSA driver and later also
layer 3 offloading which is supported by the PPE HW block.

All these patches should go through the net-next tree.

This depends on the patch "MIPS: lantiq: dma: add dev pointer" which
should go into 4.19.

Changes since:
v2:
 * Send patch "MIPS: lantiq: dma: add dev pointer" separately
 * all: removed return in register write functions
 * switch: uses phylink
 * switch: uses hardware MDIO auto polling
 * switch: use usleep_range() in MDIO busy check
 * switch: configure MDIO bus to 2.5 MHz
 * switch: disable xMII link when it is not used
 * Ethernet: use NAPI for TX cleanups
 * Ethernet: enable clock in open callback
 * Ethernet: improve skb allocation
 * Ethernet: use net_dev->stats

v1:
 * Add "MIPS: lantiq: dma: add dev pointer"
 * checkpatch fixes a all patches
 * Added binding documentation
 * use readx_poll_timeout function and ETIMEOUT error code
 * integrate GPHY firmware loading into DSA driver
 * renamed to NET_DSA_LANTIQ_GSWIP
 * removed some needed casts
 * added of_device_id.data information about the detected switch
 * fixed John's email address
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds the DSA driver for the GSWIP Switch found in the VRX200 SoC.
This switch is integrated in the DSL SoC, this SoC uses a GSWIP version
2.1, there are other SoCs using different versions of this IP block, but
this driver was only tested with the version found in the VRX200.
Currently only the basic features are implemented which will forward all
packages to the CPU and let the CPU do the forwarding. The hardware also
support Layer 2 offloading which is not yet implemented in this driver.

The GPHY FW loaded is now done by this driver and not any more by the
separate driver in drivers/soc/lantiq/gphy.c, I will remove this driver
is a separate patch. to make use of the GPHY this switch driver is
needed anyway. Other SoCs have more embedded GPHYs so this driver should
support a variable number of GPHYs. After the firmware was loaded the
GPHY can be probed on the MDIO bus and it behaves like an external GPHY,
without the firmware it can not be probed on the MDIO bus.

The clock names in the sysctrl.c file have to be changed because the
clocks are now used by a different driver. This should be cleaned up and
a real common clock driver should provide the clocks instead.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds the binding for the GSWIP (Gigabit switch) core found in the
xrx200 / VR9 Lantiq / Intel SoC.

This part takes care of the switch, MDIO bus, and loading the FW into
the embedded GPHYs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: devicetree@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

This drives the PMAC between the GSWIP Switch and the CPU in the VRX200
SoC. This is currently only the very basic version of the Ethernet
driver.

When the DMA channel is activated we receive some packets which were
send to the SoC while it was still in U-Boot, these packets have the
wrong header. Resetting the IP cores did not work so we read out the
extra packets at the beginning and discard them.

This also adapts the clock code in sysctrl.c to use the default name of
the device node so that the driver gets the correct clock. sysctrl.c
should be replaced with a proper common clock driver later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds the binding for the PMAC core between the CPU and the GSWIP
switch found on the xrx200 / VR9 Lantiq / Intel SoC.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: devicetree@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

This handles the tag added by the PMAC on the VRX200 SoC line.

The GSWIP uses internally a GSWIP special tag which is located after the
Ethernet header. The PMAC which connects the GSWIP to the CPU converts
this special tag used by the GSWIP into the PMAC special tag which is
added in front of the Ethernet header.

This was tested with GSWIP 2.1 found in the VRX200 SoCs, other GSWIP
versions use slightly different PMAC special tags.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a DMA channel is opened the IRQ should not get activated
automatically, this allows it to pull data out manually without the help
of interrupts. This is needed for a workaround in the vrx200 Ethernet
driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Document is stale, let's remove it.

Remove TCP congestion document.
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar with commit 72f6d71e ("vxlan: add ttl inherit support"),
currently ttl == 0 means "use whatever default value" on geneve instead
of inherit inner ttl. To respect compatibility with old behavior, let's
add a new IFLA_GENEVE_TTL_INHERIT for geneve ttl inherit support.
Reported-by: Jianlin Shi <jishi@redhat.com>
Suggested-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull drm nouveau fixes from Dave Airlie:
 "I'm sending this separately as it's a bit larger than I generally like
  for one driver, but it does contain a bunch of make my nvidia laptop
  not die (runpm) and a bunch to make my docking station and monitor
  display stuff (mst) fixes.

  Lyude has spent a lot of time on these, and we are putting the fixes
  into distro kernels as well asap, as it helps a bunch of standard
  Lenovo laptops, so I'm fairly happy things are better than they were
  before these patches, but I decided to split them out just for
  clarification"

* tag 'drm-fixes-2018-09-12' of git://anongit.freedesktop.org/drm/drm:
  drm/nouveau/disp/gm200-: enforce identity-mapped SOR assignment for LVDS/eDP panels
  drm/nouveau/disp: fix DP disable race
  drm/nouveau/disp: move eDP panel power handling
  drm/nouveau/disp: remove unused struct member
  drm/nouveau/TBDdevinit: don't fail when PMU/PRE_OS is missing from VBIOS
  drm/nouveau/mmu: don't attempt to dereference vmm without valid instance pointer
  drm/nouveau: fix oops in client init failure path
  drm/nouveau: Fix nouveau_connector_ddc_detect()
  drm/nouveau/drm/nouveau: Don't forget to cancel hpd_work on suspend/unload
  drm/nouveau/drm/nouveau: Prevent handling ACPI HPD events too early
  drm/nouveau: Reset MST branching unit before enabling
  drm/nouveau: Only write DP_MSTM_CTRL when needed
  drm/nouveau: Remove useless poll_enable() call in drm_load()
  drm/nouveau: Remove useless poll_disable() call in switcheroo_set_state()
  drm/nouveau: Remove useless poll_enable() call in switcheroo_set_state()
  drm/nouveau: Fix deadlocks in nouveau_connector_detect()
  drm/nouveau/drm/nouveau: Use pm_runtime_get_noresume() in connector_detect()
  drm/nouveau/drm/nouveau: Fix deadlock with fb_helper with async RPM requests
  drm/nouveau: Remove duplicate poll_enable() in pmops_runtime_suspend()
  drm/nouveau/drm/nouveau: Fix bogus drm_kms_helper_poll_enable() placement

The MV88E6xxx can have external PHYs attached to certain ports and those
PHYs could even be on different MDIO bus than the one within the switch.
This patch makes sure that ports with such PHYs are configured correctly
according to the information provided by the PHY.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

DIV_ROUND_UP has implemented the code-opened function. Therefore, just
replace the implementation with DIV_ROUND_UP.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c: In function 'qlcnic_sriov_pull_bc_msg':
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c:907:6: warning:
 variable 'fw_mbx' set but not used [-Wunused-but-set-variable]

drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c: In function 'qlcnic_sriov_issue_bc_post':
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c:939:16: warning:
 variable 'hdr_size' set but not used [-Wunused-but-set-variable]
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Fix up several Kconfig dependencies in netfilter, from Martin Willi
    and Florian Westphal.

 2) Memory leak in be2net driver, from Petr Oros.

 3) Memory leak in E-Switch handling of mlx5 driver, from Raed Salem.

 4) mlx5_attach_interface needs to check for errors, from Huy Nguyen.

 5) tipc_release() needs to orphan the sock, from Cong Wang.

 6) Need to program TxConfig register after TX/RX is enabled in r8169
    driver, not beforehand, from Maciej S. Szmigiero.

 7) Handle 64K PAGE_SIZE properly in ena driver, from Netanel Belgazal.

 8) Fix crash regression in ip_do_fragment(), from Taehee Yoo.

 9) syzbot can create conditions where kernel log is flooded with
    synflood warnings due to creation of many listening sockets, fix
    that. From Willem de Bruijn.

10) Fix RCU issues in rds socket layer, from Cong Wang.

11) Fix vlan matching in nfp driver, from Pieter Jansen van Vuuren.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (59 commits)
  nfp: flower: reject tunnel encap with ipv6 outer headers for offloading
  nfp: flower: fix vlan match by checking both vlan id and vlan pcp
  tipc: check return value of __tipc_dump_start()
  s390/qeth: don't dump past end of unknown HW header
  s390/qeth: use vzalloc for QUERY OAT buffer
  s390/qeth: switch on SG by default for IQD devices
  s390/qeth: indicate error when netdev allocation fails
  rds: fix two RCU related problems
  r8169: Clear RTL_FLAG_TASK_*_PENDING when clearing RTL_FLAG_TASK_ENABLED
  erspan: fix error handling for erspan tunnel
  erspan: return PACKET_REJECT when the appropriate tunnel is not found
  tcp: rate limit synflood warnings further
  MIPS: lantiq: dma: add dev pointer
  netfilter: xt_hashlimit: use s->file instead of s->private
  netfilter: nfnetlink_queue: Solve the NFQUEUE/conntrack clash for NF_REPEAT
  netfilter: cttimeout: ctnl_timeout_find_get() returns incorrect pointer to type
  netfilter: conntrack: timeout interface depend on CONFIG_NF_CONNTRACK_TIMEOUT
  netfilter: conntrack: reset tcp maxwin on re-register
  qmi_wwan: Support dynamic config on Quectel EP06
  ethernet: renesas: convert to SPDX identifiers
  ...

Add support for entries which are "sticky", i.e. will not change their port
if they show up from a different one. A new ndm flag is introduced for that
purpose - NTF_STICKY. We allow to set it only to non-local entries.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
Preparing for phylib linkmodes

phylib currently makes us of a u32 bitmap for advertising, supported,
and link partner capabilities. For a long time, this has been
sufficient, for devices up to 1Gbps. With more MAC/PHY combinations
now supporting speeds greater than 1Gbps, we have run out of
bits. There is the need to replace this u32 with an
__ETHTOOL_DECLARE_LINK_MODE_MASK, which makes use of linux's generic
bitmaps.

This patchset does some of the work preparing for this change. A few
cleanups are applied to PHY drivers. Some MAC drivers directly access
members of phydev which are going to change type. These patches adds
some helpers and swaps MAC drivers to use them, mostly dealing with
Pause configuration.

v3:
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Add missing at in commit message
Change Subject of patch 5
Fix return in from phy_set_asym_pause
Fix kerneldoc in phy_set_pause

v2:
Fixup bad indentation in tg3.c
Rename phy_support_pause() to phy_support_sym_pause()
Also trigger autoneg if the advertising settings have changed.
Rename phy_set_pause() to phy_set_sym_pause()
Use the bcm63xx_enet.c logic, not fec_main.c for validating pause
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Rather than have MAC drivers open code the test, add a helper in
phylib. This will help when we change the type of phydev->supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool can be used to enable/disable pause. Add a helper to configure
the PHY when Pause is supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool can be used to enable/disable pause. Add a helper to configure
the PHY when asym pause is supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rather than have the MAC drivers manipulate phydev members, add a
helper function for MACs supporting Pause, but not Asym Pause.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rather than have the MAC drivers manipulate phydev members to indicate
they support Asym Pause, add a helper function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some MAC hardware cannot support a subset of link modes. e.g. often
1Gbps Full duplex is supported, but Half duplex is not. Add a helper
to remove such a link mode.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PHY drivers don't indicate they support pause. They expect MAC drivers
to enable its support if the MAC has the needed hardware. Thus MAC
drivers should not mask Pause support, but enable it.

Change a few ANDs to ORs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The phy supported speed is being used to determine if the MAC should
be configured to 100 or 1G. The masking logic is broken. Instead, look
at 1G supported speeds to enable 1G MAC support.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Many Ethernet MAC drivers want to limit the PHY to only advertise a
maximum speed of 100Mbs or 1Gbps. Rather than using a mask, make use
of the helper function phy_set_max_speed().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is nothing in this driver which prevents it to be compiled for
other architectures. Add COMPILE_TEST so we get better compile test
coverage.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver indicates it can do 10/100 full and half duplex, plus 1G
Full. The datasheet indicates 1G half is also supported. So make use
of the standard PHY_GBIT_FEATURES.

It could be, this was added because there is a MAC which does not
support 1G half. Bit this is the wrong place to enforce this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PHY driver should not indicate that Pause is supported. It is upto
the MAC drive enable it, if it supports Pause frames. So remove it
from the ste10Xp driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Report in standard netdev stats drops and errors as well as
RX multicast from the FW vNIC counters.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
nfp: flower: fixes for flower offload

Two fixes for flower matching and tunnel encap.  Pieter fixes
VLAN matching if the entire VLAN id is masked out and match
is only performed on the PCP field.  Louis adds validation of
tunnel flags for encap, most importantly we should not offload
actions on IPv6 tunnels if it's not supported.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>