- 12 Apr, 2023 7 commits
-
-
Ville Syrjälä authored
Now that VRR enable/disable are called from convenient places it is trivial to allow it to change state during fastsets. Make it so. Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/7542Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230320203352.19515-7-ville.syrjala@linux.intel.comReviewed-by:
Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
-
Ville Syrjälä authored
Move VRR enabling/disabling into a place where it also works for fastsets. With this we always start the transcoder up in non-VRR mode. Granted we already did that but for a very short period of time. But now that we might end up doing a bit more with the transcoder in non-VRR mode it seems prudent to also update the active timings as the transcoder changes its operating mode. crtc_state->vrr.enable still tracks whether VRR is actually enabled or not, but now we configure all the other VRR timing registers whenever VRR is possible (whether we actually enable it or not). crtc_state->vrr.flipline can now serve as our "is VRR possible" bit of state. I decided to leave the MSA timing ignore bit set all the time whether VRR is actually enabled or not. If the sink can figure out the timings with that information when VRR is active then surely it can also do it when VRR is inactive. v2: Protect intel_vrr_set_transcoder_timings() with HAS_VRR() Signed-off-by:
-
Ville Syrjälä authored
In order to move VRR enable/disable to a place where it's also applicable to fastsets we need to be prepared to configure the pipe into non-VRR mode initially, and then later switch to VRR mode. To that end allow the active timings to be configured in non-VRR mode temporarily even when the crtc_state says we're going to be using VRR. Signed-off-by:
-
Ville Syrjälä authored
On adl/dg2 a chicken bit needs to be set for TRANS_SET_CONTENXT_LATENCY to take effect in VRR mode. Can't really think of a reason why we'd ever disable that chicken bit, so let's just always set it. Signed-off-by:
-
Ville Syrjälä authored
Some of the VRR functions take redundant arguments. Get rid of them to make life simpler. Signed-off-by:
-
Ville Syrjälä authored
I want to use the same logic that planes_{enabling,disabling}() are using for other features as well. Generlize the thing into a pair of macros. Signed-off-by: -
Jani Nikula authored
Leftovers from before display debugfs was separated to its own file. Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Reviewed-by:
Nirmoy Das <nirmoy.das@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230411131922.401602-1-jani.nikula@intel.com
-
- 11 Apr, 2023 11 commits
-
-
Ville Syrjälä authored
Have the state checker validate that the csc matrices look correct when read back from the hardware. Signed-off-by:
Ankit Nautiyal <ankit.k.nautiyal@intel.com>
-
Ville Syrjälä authored
Include the csc matrices in the state dump. The format being hardware specific we just dump as hex for now. Might have to think of some way to get a bit more human readable output... Signed-off-by:
-
Ville Syrjälä authored
Read out the csc matrix on chv, and stash the result into the correct spot in the crtc state. Signed-off-by:
-
Ville Syrjälä authored
Read out the pipe/output csc matrices on ilk+ and stash the results (in the hardware specific format) into the appropriate place in the crtc state. Note that on skl/glk/icl the pipe csc unit suffers from an issue where *reads* of the coefficient/offset registers also disarm the double buffer update (if currently armed via CSC_MODE write). So it's rather important that the readout only happens after the csc registers have been latched. Fortunately the state checker only runs after the start of vblank where the latching happens. And on skl/glk the DMC + CSC register read has the potential to corrupt the latched CSC register values, so let's add a comment reminding us that the DC states should remain off until the readout has been completed. TODO: maybe we could somehow check to make sure PSR has in fact latched the new register values already, and that DC states have been off all along? Signed-off-by:
-
Ville Syrjälä authored
Make sure the csc enable bit(s) match the way we're about to fill the csc matrices. Signed-off-by:
-
Ville Syrjälä authored
Store the chv cgm csc matrix in the crtc state as well. We shall store it in the same place where we store the ilk+ pipe csc matrix (as opposed to the output csc matrix). Signed-off-by:
-
Ville Syrjälä authored
Embed a pair of intel_csc_matrix structs in the crtc state, and fill them out appropriately during atomic_check(). Since pre-ivb platforms don't have programmable post offsets we shall leave those zeroed, mainly in preparation for state readout+check. Signed-off-by:
-
Ville Syrjälä authored
Convert chv_cgm_csc_convert_ctm() over to using the new intel_csc_matrix structure. No pre/post offsets on this hardware so only the coefficients get filled out. Signed-off-by:
-
Ville Syrjälä authored
Split chv_cgm_csc_convert_ctm() out from chv_load_cgm_csc() so that we have functions with clear jobs. This is also how the ilk+ code is already structured. Signed-off-by:
-
Ville Syrjälä authored
Introduce a structure that can hold our CSC matrices. In there we shall have the preoffsets, postoffsets, and coefficients, all in platform specific format (at least for now). We shall start by converting the ilk+ code to make use of the new structure. chv will come later. Signed-off-by:
-
Ville Syrjälä authored
Our current limited range matrix is a bit off. I think it was originally calculated with rounding, as if we wanted the normal pixel replication type of behaviour. That is, since the 8bpc max value is 0xeb we assumed the 16bpc max value should be 0xebeb, but what the HDMI spec actually says it should be is 0xeb00. So to get what we want we make the formula out = in * (235-16) << (12-8) / in_max + 16 << (12-8), with 12 being precision of the csc, 8 being the precision of the constants we used. The hardware takes its coefficients as floating point values, but the (235−16)/255 = ~.86, so exponent 0 is what we want anyway, so it works out perfectly without having to hardcode it in hex or start playing with floats. In terms of raw numbers we are feeding the hardware the post offset changes from 0x101 to 0x100, and the coefficient changes from 0xdc0 to 0xdb0 (~.860->~.855). So this should make everything come out just a tad darker. I already used better constants in lut_limited_range() earlier so the output of the two paths should be closer now. Signed-off-by:
-
- 06 Apr, 2023 2 commits
-
-
Jani Nikula authored
Fix the warning: drivers/gpu/drm/i915/intel_wakeref.h:118: warning: expecting prototype for intel_wakeref_get_if_in_use(). Prototype was for intel_wakeref_get_if_active() instead Signed-off-by:
Vinod Govindapillai <vinod.govindapillai@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230405104142.766598-2-jani.nikula@intel.com
-
Jani Nikula authored
There's not much point in a static work function having a kernel-doc comment. Just clean it up and make it a regular comment. This fixes the kernel-doc warnings: drivers/gpu/drm/i915/display/intel_tc.c:1370: warning: Function parameter or member 'work' not described in 'intel_tc_port_disconnect_phy_work' drivers/gpu/drm/i915/display/intel_tc.c:1370: warning: Excess function parameter 'dig_port' description in 'intel_tc_port_disconnect_phy_work' Signed-off-by:
-
- 05 Apr, 2023 5 commits
-
-
Jani Nikula authored
Follow the contemporary naming style. Include some indentation fixes while at it on the affected statements. One function needs to keep using dev_priv due to implicit dev_priv usage in a macro. Reviewed-by:
Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by:
-
Jani Nikula authored
Observe that intel_pm.[ch] is now purely about clock gating, so rename them to intel_clock_gating.[ch]. Rename the functions to intel_clock_gating_*() to follow coding conventions. Reviewed-by:
-
Alan Previn authored
MESA driver is creating protected context on every driver handle creation to query caps bits for app. So when running CI tests, they are observing hundreds of drm_errors when enabling PXP in .config but using SOC fusing or BIOS configuration that cannot support PXP sessions. The fixes tag referenced below was to resolve a related issue where we wanted to silence error messages, but that case was due to outdated IFWI (firmware) that definitely needed an upgrade and was, at that point, considered a one-off case as opposed to today's realization that default CI was enabling PXP in kernel config for all testing. So with this patch, let's strike a balance between issues that is critical but are root-caused from HW/platform gaps (louder drm-warn but just ONCE) vs other cases where it could also come from session state machine (which cannot be a WARN_ONCE since it can be triggered due to runtime operation events). Let's use helpers for these so as more functions are added in future features / HW (or as FW designers continue to bless upstreaming of the error codes and meanings), we only need to update the helpers. NOTE: Don't completely remove FW errors (via drm_debug) or else cusomer apps that really needs to know that content protection failed won't be aware of it. v2: - Add fixes tag (Trvtko) v3: - Break multi-line drm_dbg strings into separate drm_dbg (Daniele) - Fix couple of typecasting nits (Daniele) v4: - Unsuccessful PXP FW cmd due to platform configuration shouldn't use drm_WARN_once (Tvrtko), Switched to use drm_info_once. v5: - Added "reported-and-tested" by Eero. Reported-and-tested-by:Eero Tamminen <eero.t.tamminen@intel.com> Fixes: b762787b ("drm/i915/pxp: Use drm_dbg if arb session failed due to fw version") Signed-off-by:
Alan Previn <alan.previn.teres.alexis@intel.com> Reviewed-by:
Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Signed-off-by:
-
Jani Nikula authored
Enabling kernel-doc warnings in commit aaee4bbe ("drm/i915: enable kernel-doc warnings for CONFIG_DRM_I915_WERROR=y") actually only covers the .c files. And it's good for avoiding warnings in W= builds. However, we need something more to check for kernel-doc issues in headers. Add it as part of the existing HDRTEST. We have tons of issues, and this unleashes warnings galore on CONFIG_DRM_I915_WERROR=y. It doesn't fail the build because (at least for now) we don't pass -Werror to kernel-doc. Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by:
-
Stanislav Lisovskiy authored
According to spec, we should check if output_bpp * pixel_rate is less than DDI clock * 72, if UHBR is used. v2: - s/pipe_config/crtc_state/ (Jani Nikula) - Merged previous patch into that one, to remove empty function(Jani Nikula) v3: - Make that constraint check to be DSC-related only - Limit this to only DISPLAY_VER <= 13 v4: - Move constraint check to the top(Vinod Govindapillai) HSDES: 1406899791 BSPEC: 49259 Signed-off-by:Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> Reviewed-by:
-
- 04 Apr, 2023 3 commits
-
-
Jani Nikula authored
Increase awareness of kernel-doc issues by enabling doc check locally when CONFIG_DRM_I915_WERROR=y is enabled. Once the warnings have been fixed, we can pass -Werror to kernel-doc locally, and fail the build when there are kernel-doc warnings in i915. v2: Don't check for KBUILD_EXTRA_WARN (Masahiro) Cc: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by:
-
Jani Nikula authored
Clean up i915_reg.h by splitting out PSR regs to display/intel_psr_regs.h. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
-
Jani Nikula authored
Clean up i915_reg.h by splitting out SKL+ watermark regs to display/skl_watermark_regs.h. v2: Rebased Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Nirmoy Das <nirmoy.das@intel.com> # v1 Signed-off-by:
-
- 03 Apr, 2023 12 commits
-
-
Ville Syrjälä authored
Replace the hardcoded final numbers in the AUX SYNC/precharge setup, and derive those from numbers from the (e)DP specs. The new functions can serve as the single point of truth for the number of SYNC pulses we use. Cc: Jouni Högander <jouni.hogander@intel.com> Signed-off-by:
Jouni Högander <jouni.hogander@intel.com>
-
Ville Syrjälä authored
Fast wake should use 8 SYNC pulses for the preamble and 10-16 SYNC pulses for the precharge. Reduce our fast wake SYNC count to match the maximum value. We also use the maximum precharge length for normal AUX transactions. Cc: Jouni Högander <jouni.hogander@intel.com> Signed-off-by:
-
Ashutosh Dixit authored
On ATSM the PL1 limit is disabled at power up. The previous uapi assumed that the PL1 limit is always enabled and therefore did not have a notion of a disabled PL1 limit. This results in erroneous PL1 limit values when the PL1 limit is disabled. For example at power up, the disabled ATSM PL1 limit was previously shown as 0 which means a low PL1 limit whereas the limit being disabled actually implies a high effective PL1 limit value. To get round this problem, the PL1 limit uapi is expanded to include a special value 0 to designate a disabled PL1 limit. A read value of 0 means that the PL1 power limit is disabled, writing 0 disables the limit. The link between this patch and the bugs mentioned below is as follows: * Because on ATSM the PL1 power limit is disabled on power up and there were no means to enable it, we previously implemented the means to enable the limit when the PL1 hwmon entry (power1_max) was written to. * Now there is a IGT igt@i915_hwmon@hwmon_write which (a) reads orig value from all hwmon sysfs (b) does a bunch of random writes and finally (c) restores the orig value read. On ATSM since the orig value is 0, when the IGT restores the 0 value, the PL1 limit is now enabled with a value of 0. * PL1 limit of 0 implies a low PL1 limit which causes GPU freq to fall to 100 MHz. This causes GuC FW load and several IGT's to start timing out and gives rise to these Intel CI bugs. After this patch, writing 0 would disable the PL1 limit instead of enabling it, avoiding the freq drop issue. v2: Add explanation for bugs mentioned below (Rodrigo) v3: Eliminate race during PL1 disable and verify (Tvrtko) Change return to -ENODEV if verify fails (Tvrtko) Link: https://gitlab.freedesktop.org/drm/intel/-/issues/8062 Link: https://gitlab.freedesktop.org/drm/intel/-/issues/8060Signed-off-by:Ashutosh Dixit <ashutosh.dixit@intel.com> Reviewed-by:
-
Lee Jones authored
Fixes the following W=1 kernel build warning(s): drivers/gpu/drm/i915/display/intel_wm.c:46: warning: Function parameter or member 'i915' not described in 'intel_update_watermarks' drivers/gpu/drm/i915/display/intel_wm.c:46: warning: Excess function parameter 'dev_priv' description in 'intel_update_watermarks' Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Cc: David Airlie <airlied@gmail.com> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com> Cc: intel-gfx@lists.freedesktop.org Cc: dri-devel@lists.freedesktop.org Signed-off-by:
Lee Jones <lee@kernel.org> Signed-off-by:
-
Lee Jones authored
drm/i915/display/intel_display_power: Fix incorrectly documented function __intel_display_power_put_async() Fixes the following W=1 kernel build warning(s): drivers/gpu/drm/i915/display/intel_display_power.c:712: warning: expecting prototype for intel_display_power_put_async(). Prototype was for __intel_display_power_put_async() instead Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Cc: David Airlie <airlied@gmail.com> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Imre Deak <imre.deak@intel.com> Cc: intel-gfx@lists.freedesktop.org Cc: dri-devel@lists.freedesktop.org Signed-off-by:
-
Lee Jones authored
Fixes the following W=1 kernel build warning(s): drivers/gpu/drm/i915/display/intel_display_debugfs.c:1668: warning: Function parameter or member 'intel_connector' not described in 'intel_connector_debugfs_add' drivers/gpu/drm/i915/display/intel_display_debugfs.c:1668: warning: Excess function parameter 'connector' description in 'intel_connector_debugfs_add' Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Cc: David Airlie <airlied@gmail.com> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: intel-gfx@lists.freedesktop.org Cc: dri-devel@lists.freedesktop.org Signed-off-by:
-
Imre Deak authored
The encoder update_prepare()/complete() hooks were added to hold a TC port link reference for all outputs in the atomic state around the whole modeset enable sequence - thus locking the ports' TC mode - and set the TBT/DP-alt PLL type corresponding to the current TC mode. Since nothing depends on the PLL selection before/after then encoder's pre_pll_enable/post_pll_disable hooks are called, the above steps can be moved to these hooks, so do that and remove the update_prepare()/complete() hooks. Reviewed-by:
Mika Kahola <mika.kahola@intel.com> Signed-off-by:
Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-30-imre.deak@intel.com
-
Imre Deak authored
After the previous patch the workaround for a TC PHY hang issue is not required any more, remove it. Reviewed-by:
-
Imre Deak authored
Bspec requires disabling the DPLLs on TC ports before disconnecting the port's PHY. Add a post_pll_disable encoder hook and move the call to disconnect the port's PHY from the post_disable hook to the new hook. Reviewed-by:
-
Imre Deak authored
The spec requires disabling the PLL on TC ports before disconnecting the port's PHY. Prepare for that by moving the PLL disabling to the CRTC disable hook, while disconnecting the PHY will be moved to the post_pll_disable() encoder hook in the next patch. v2: Move the call from intel_crtc_disable_noatomic() as well. Reviewed-by: Mika Kahola <mika.kahola@intel.com> # v1 Signed-off-by:
-
Imre Deak authored
Bspec has updated the TC connect/disconnect sequences, add the required platform hooks for these. The difference wrt. the old sequence is the order of taking the PHY ownership - while holding a port power reference this requires - and blocking the TC-cold power state. Bspec: 49294 Reviewed-by:
-
Imre Deak authored
Connecting the PHY for connector probing - also blocking TC-cold - isn't required and has some overhead. Taking only the mutex is sufficient, so do that. Reviewed-by:
-
