This commit moves the dma_info array to the end of struct mlx5e_mpw_info
to make it a flexible array. It also removes the intermediate struct
mlx5e_umr_dma_info, which used to contain only this array. The
flexibility of dma_info will allow to choose its size dynamically in a
following commit.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Normally, the MTU change requires reopening the channels, but it can be
skipped if the new MTU doesn't change any of the queue parameters and if
MTU is not used in the data path.

The shortcut is applicable to the non-linear mode of striding RQ,
because the only thing affected by MTU is the queue length. As ethtool
sets the queue length in packets, but striding RQ length is defined in
strides or bytes, we estimate the RQ length to be at least as big as the
requested number of MTU-sized packets, that's why it depends on MTU.

Improve the shortcut by actually checking whether the RQ length stayed
the same, instead of an intermediate step in the calculation.

As MTU also affects the SHAMPO parameters, skip the shortcut if SHAMPO
is in use.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In a typical scenario, if an XSK socket is opened first, then an XDP
program is attached, mlx5e_validate_xsk_param will be called twice:
first on XSK bind, second on channel restart caused by enabling XDP. The
validation includes a call to mlx5e_rx_is_linear_skb, which checks the
presence of the XDP program.

The above means that mlx5e_rx_is_linear_skb might return true the first
time, but false the second time, as mlx5e_rx_get_linear_sz_skb's return
value will increase, because of a different headroom used with XDP.

As XSK RQs never exist without XDP, it would make sense to trick
mlx5e_rx_get_linear_sz_skb into thinking XDP is enabled at the first
check as well. This way, if MTU is too big, it would be detected on XSK
bind, without giving false hope to the userspace application.

However, it turns out that this check is too restrictive in the first
place. SKBs created on XDP_PASS on XSK RQs don't have any headroom. That
means that big MTUs filtered out on the first and the second checks
might actually work.

So, address this issue in the proper way, but taking into account the
absence of the SKB headroom on XSK RQs, when calculating the buffer
size.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

One of the checks in mlx5e_rx_is_linear_skb verifies that the RX buffer
fits into the XSK frame size. Remove the duplicating check from
mlx5e_validate_xsk_param. It allows to make mlx5e_rx_get_min_frag_sz
static.

Remove mlx5e_rx_is_xdp altogether, as its only usage is located in a
branch where xsk == NULL.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Linear RX buffers must be big enough to fit the MTU-sized packet along
with the headroom. On the other hand, they must be small enough to fit
into a page (or into an XSK frame). A straightforward way to check
whether the linear mode is possible would be comparing the required
buffer size to PAGE_SIZE or XSK frame size.

Stride size in the linear mode is defined by the following constraints:

1. A stride is at least as big as the buffer size, and it's a power of
two.

2. If non-XSK XDP is enabled, the stride size is PAGE_SIZE, because
mlx5e requires each packet to be in its own page when XDP is in use. The
previous constraint is automatically fulfilled, because buffer size
can't be bigger than PAGE_SIZE.

3. XSK uses stride size equal to PAGE_SIZE, but the following commits
will allow it to use roundup_pow_of_two(XSK frame size), by allowing the
NIC's MMU to use page sizes not equal to the CPU page size.

This commit puts the above requirements and constraints straight to the
code in an attempt to simplify it and to prepare it for changes made in
the next patches.

For the reference, the old code uses an equivalent, but trickier
calculation (high-level simplified pseudocode):

    if XDP or XSK:
        mlx5e_rx_get_linear_frag_sz := max(buffer size, PAGE_SIZE)
    else:
        mlx5e_rx_get_linear_frag_sz := buffer size
    mlx5e_rx_is_linear_skb := mlx5e_rx_get_linear_frag_sz <= PAGE_SIZE
    stride size := roundup_pow_of_two(mlx5e_rx_get_linear_frag_sz)

The new code effectively removes mlx5e_rx_get_linear_frag_sz that used
to return either buffer size or stride size, depending on the situation,
making it hard to work with and to make changes:

    if XDP or XSK:
        mlx5e_rx_get_linear_stride_sz := PAGE_SIZE
    else
        mlx5e_rx_get_linear_stride_sz := roundup_pow_of_two(buffer size)
    mlx5e_rx_is_linear_skb := buffer size <= (PAGE_SIZE or XSK frame sz)
    stride size := mlx5e_rx_get_linear_stride_sz
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Instead of WARNing in runtime when TLS offload WQEs posted to ICOSQ are
over the hardware limit, check their size before enabling TLS RX
offload, and block the offload if the condition fails. It also allows to
drop a u16 field from struct mlx5e_icosq.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

TX MPWQE size is limited to the cacheline-aligned maximum. Use the same
value for the stop room and the capability check.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Fix a typo in the function name: mpqwe -> mpwqe (stands for multi-packet
work queue element).
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mlx5e_alloc_xdpsq calculates sq->stop_room internally, but there is
already a function for that: mlx5e_stop_room_for_max_wqe. This commit
makes use of this function.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

To shorten and simplify code, let mlx5e_get_sw_max_sq_mpw_wqebbs accept
mdev and derive max SQ WQEBBs from it. Also rename the function to a
more generic name mlx5e_get_max_sq_aligned_wqebbs, because the following
patches will use it in non-MPWQE contexts.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Currently, the driver can silently fall back to legacy RQ after enabling
XDP, even if striding RQ was active before. It happens when PAGE_SIZE is
bigger than the maximum supported stride size. This commit changes this
behavior to more straightforward: if an operation (enabling XDP) doesn't
support the current parameters (striding RQ mode), it fails.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mlx5e_verify_rx_mpwqe_strides is only used in en/params.c, so it can be
made static and removed from en/params.h.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

No need to keep max_sq_wqebbs in mlx5e_txqsq and mlx5e_xdpsq, as it's
only used when allocating the queues. Removing an extra field reduces
the struct size.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The return value of mlx5e_get_max_sq_wqebbs is clamped down to
MLX5_SEND_WQE_MAX_WQEBBS = 16, which fits into u8. This commit changes
the return type of this function to u8 for stricter type safety.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add the capability that will allow the driver to determine the minimal
MTT page size to be able to map the smallest possible pages in XSK. The
older firmwares that don't have this capability default to 12 (i.e.
4096-byte pages).
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Saeed Mahameed says:

====================
updates from mlx5-next 2022-09-24

Updates form mlx5-next including[1]:

1) HW definitions and support for NPPS clock settings.

2) various cleanups

3) Enable hash mode by default for all NICs

4) page tracker and advanced virtualization HW definitions for vfio

[1] https://lore.kernel.org/netdev/20220907233636.388475-1-saeed@kernel.org/

* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
  net/mlx5: Remove from FPGA IFC file not-needed definitions
  net/mlx5: Remove unused structs
  net/mlx5: Remove unused functions
  net/mlx5: detect and enable bypass port select flow table
  net/mlx5: Lag, enable hash mode by default for all NICs
  net/mlx5: Lag, set active ports if support bypass port select flow table
  RDMA/mlx5: Don't set tx affinity when lag is in hash mode
  net/mlx5: add IFC bits for bypassing port select flow table
  net/mlx5: Add support for NPPS with real time mode
  net/mlx5: Expose NPPS related registers
  net/mlx5: Query ADV_VIRTUALIZATION capabilities
  net/mlx5: Introduce ifc bits for page tracker
  RDMA/mlx5: Move function mlx5_core_query_ib_ppcnt() to mlx5_ib
====================

Link: https://lore.kernel.org/all/20220927201906.234015-1-saeed@kernel.org/Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Just use kzalloc instead.

Fixes: d6f1e89b ("sunhme: Return an ERR_PTR from quattro_pci_find")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20220928004157.279731-1-seanga2@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Use skb_put_data() instead of skb_put() and memcpy(), which is clear.
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Reviewed-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Link: https://lore.kernel.org/r/20220927023254.30342-1-shangxiaojing@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Vladimir Oltean says:

====================
Rework resource allocation in Felix DSA driver

The Felix DSA driver controls NXP variations of Microchip switches.
Colin Foster is trying to add support in this driver for "genuine"
Microchip hardware, but some of the NXP-isms in this driver need to go
away before that happens cleanly.
https://patchwork.kernel.org/project/netdevbpf/cover/20220926002928.2744638-1-colin.foster@in-advantage.com/

The starting point was Colin's patch 08/14 "net: dsa: felix: update
init_regmap to be string-based", and this continues to be the central
theme here, but things are done differently.

In short (full explanations are in patches), the goal is for MFD-based
switches like Colin's SPI-controlled VSC7512 to be able to request a
regmap that was created 100% externally (by drivers/mfd/ocelot-core.c)
in a very simple way, that does not create dependencies on other
modules. That is dev_get_regmap(), and as input it wants a string, for
the resource name. So we rework the resource allocation in this driver
to be based on string names provided by the specific instantiation (in
Colin's case, ocelot_ext.c).

Patch set was boot-tested on NXP LS1028A.
====================

Link: https://lore.kernel.org/r/20220927191521.1578084-1-vladimir.oltean@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Existing felix DSA drivers (vsc9959, vsc9953) are all switches that were
integrated in NXP SoCs, which makes them a bit unusual compared to the
usual Microchip branded Ocelot switches.

To be precise, looking at
Documentation/devicetree/bindings/net/mscc,vsc7514-switch.yaml, one can
see 21 memory regions for the "switch" node, and these correspond to the
"targets" of the switch IP, which are spread throughout the guts of that
SoC's memory space.

In NXP integrations, those targets still exist, but they were condensed
within a single memory region, with no other peripheral in between them,
so it made more sense for the driver to ioremap the entire memory space
of the switch, and then find the targets within that memory space via
some offsets hardcoded in the driver.

The effect of this design decision is that now, the felix driver expects
hardware instantiations to provide their own resource definitions, which
is kind of odd when considering a typical device (those are retrieved
from 'reg' properties in the device tree, using platform_get_resource()
or similar).

Allow other hardware instantiations that share the felix driver to not
provide a hardcoded array of resources in the future. Instead, make the
common denominator based on which regmaps are created be just the
resource "names". Each instantiation comes with its own array of names
that are mandatory for it, and with an optional array of resources.

So we split the resources in 2 arrays, one is what's requested and the
other is what's provided. There is one pool of provided resources, in
felix->info->resources (of length felix->info->num_resources). There are
2 different ways of requesting a resource. One is by enum ocelot_target
(this handles the global regmaps), and one is by int port (this handles
the per-port ones).

For the existing vsc9959 and vsc9953, it would be a bit stupid to
request something that's not provided, given that the 2 arrays are both
defined in the same place.

The advantage is that we can now modify felix_request_regmap_by_name()
to make felix->info->resources[] optional, and if absent, the
implementation can call dev_get_regmap() and this is something that is
compatible with MFD.
Co-developed-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Use less verbose resource definitions in vsc9959 and vsc9953. This also
sets IORESOURCE_MEM in the constant array of resources, so we don't have
to do this from felix_init_structs() - in fact, in the future, we may
even support IORESOURCE_REG resources.

Note that this macro takes start and length as argument, and we had
start and end before. So transform end into length.

While at it, sort the resources according to their offset.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

It turns out that the idea of having a customizable implementation of a
regmap creation from a resource is not exactly useful. The idea was for
the new MFD-based VSC7512 driver to use something that creates a SPI
regmap from a resource. But there are problems in actually getting those
resources (it involves getting them from MFD).

To avoid all that, we'll be getting resources by name, so this custom
init_regmap() method won't be needed. Remove it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This address is only relevant for the vsc9959, which is a PCIe device
that holds its switch registers in a different PCIe BAR compared to the
registers for the internal MDIO controller.

Hide this aspect from the common felix driver and move the
pci_resource_start() call to the only place that needs it, which is in
vsc9959_mdio_bus_alloc().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The imdio_res is used only by vsc9959, which references its own
vsc9959_imdio_res through the common felix_info->imdio_res pointer.
Since the common code doesn't care about this resource (and it can't be
part of the common array of resources, either, because it belongs in a
different PCI BAR), just reference it directly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().

Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The v6_rcv_saddr and rcv_saddr are inside a union in the
'struct inet_bind2_bucket'.  When searching a bucket by following the
bhash2 hashtable chain, eg. inet_bind2_bucket_match, it is only using
the sk->sk_family and there is no way to check if the inet_bind2_bucket
has a v6 or v4 address in the union.  This leads to an uninit-value
KMSAN report in [0] and also potentially incorrect matches.

This patch fixes it by adding a family member to the inet_bind2_bucket
and then tests 'sk->sk_family != tb->family' before matching
the sk's address to the tb's address.

Cc: Joanne Koong <joannelkoong@gmail.com>
Fixes: 28044fc1 ("net: Add a bhash2 table hashed by port and address")
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Tested-by: Alexander Potapenko <glider@google.com>
Link: https://lore.kernel.org/r/20220927002544.3381205-1-kafai@fb.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Mat Martineau says:

====================
mptcp: MPTCP support for TCP_FASTOPEN_CONNECT

RFC 8684 appendix B describes how to use TCP Fast Open with MPTCP. This
series allows TFO use with MPTCP using the TCP_FASTOPEN_CONNECT socket
option. The scope here is limited to the initiator of the connection -
support for MSG_FASTOPEN and the listener side of the connection will be
in a separate series. The preexisting TCP fastopen code does most of the
work, so these changes mostly involve plumbing MPTCP through to those
TCP functions.

Patch 1 changes the MPTCP socket option code to pass the
TCP_FASTOPEN_CONNECT option through to the initial unconnected subflow.

Patch 2 exports the existing tcp_sendmsg_fastopen() function from tcp.c

Patch 3 adds the call to tcp_sendmsg_fastopen() from the MPTCP send
function.

Patch 4 modifies mptcp_poll() to handle the deferred TFO connection.
====================

Link: https://lore.kernel.org/r/20220926232739.76317-1-mathew.j.martineau@linux.intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

If fastopen is used, poll must allow a first write that will trigger
the SYN+data

Similar to what is done in tcp_poll().
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Benjamin Hesmans <benjamin.hesmans@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When TCP_FASTOPEN_CONNECT has been set on the socket before a connect,
the defer flag is set and must be handled when sendmsg is called.

This is similar to what is done in tcp_sendmsg_locked().
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Co-developed-by: Benjamin Hesmans <benjamin.hesmans@tessares.net>
Signed-off-by: Benjamin Hesmans <benjamin.hesmans@tessares.net>
Signed-off-by: Dmytro Shytyi <dmytro@shytyi.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

It will be used to support TCP FastOpen with MPTCP in the following
commit.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Co-developed-by: Dmytro Shytyi <dmytro@shytyi.net>
Signed-off-by: Dmytro Shytyi <dmytro@shytyi.net>
Signed-off-by: Benjamin Hesmans <benjamin.hesmans@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Set the option for the first subflow only. For the other subflows TFO
can't be used because a mapping would be needed to cover the data in the
SYN.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Benjamin Hesmans <benjamin.hesmans@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Zero-length arrays are deprecated and we are moving towards adopting
C99 flexible-array members, instead. So, replace zero-length arrays
declarations in anonymous union with the new DECLARE_FLEX_ARRAY()
helper macro.

This helper allows for flexible-array members in unions.

Link: https://github.com/KSPP/linux/issues/193
Link: https://github.com/KSPP/linux/issues/225
Link: https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.htmlSigned-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/YzIvfGXxfjdXmIS3@workSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pavel Begunkov says:

====================
shrink struct ubuf_info

struct ubuf_info is large but not all fields are needed for all
cases. We have limited space in io_uring for it and large ubuf_info
prevents some struct embedding, even though we use only a subset
of the fields. It's also not very clean trying to use this typeless
extra space.

Shrink struct ubuf_info to only necessary fields used in generic paths,
namely ->callback, ->refcnt and ->flags, which take only 16 bytes. And
make MSG_ZEROCOPY and some other users to embed it into a larger struct
ubuf_info_msgzc mimicking the former ubuf_info.

Note, xen/vhost may also have some cleaning on top by creating
new structs containing ubuf_info but with proper types.
====================

Link: https://lore.kernel.org/r/cover.1663892211.git.asml.silence@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

We can benefit from a smaller struct ubuf_info, so leave only mandatory
fields and let users to decide how they want to extend it. Convert
MSG_ZEROCOPY to struct ubuf_info_msgzc and remove duplicated fields.
This reduces the size from 48 bytes to just 16.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

struct ubuf_info will be changed, use ubuf_info_msgzc instead.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

struct ubuf_info will be changed, use ubuf_info_msgzc instead.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

We're going to split struct ubuf_info and leave there only
mandatory fields. Users are free to extend it. Add struct
ubuf_info_msgzc, which will be an extended version for MSG_ZEROCOPY and
some other users. It duplicates of struct ubuf_info for now and will be
removed in a couple of patches.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Florian Westphal says:

====================
netfilter fix for net-next

This is a late bug fix for the *net-next* tree to make nftables
"fib" expression play nice with VRF devices.

This was broken since day 1 (v4.10) so I don't see a compelling reason
to push this via net at the last minute.

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
  netfilter: nft_fib: Fix for rpath check with VRF devices
====================

Link: https://lore.kernel.org/r/20220928113908.4525-1-fw@strlen.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Analogous to commit b575b24b ("netfilter: Fix rpfilter
dropping vrf packets by mistake") but for nftables fib expression:
Add special treatment of VRF devices so that typical reverse path
filtering via 'fib saddr . iif oif' expression works as expected.

Fixes: f6d0cbcf ("netfilter: nf_tables: add fib expression")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Florian Westphal <fw@strlen.de>

Edward Cree says:

====================
sfc: bare bones TC offload

This series begins the work of supporting TC flower offload on EF100 NICs.
This is the absolute minimum viable TC implementation to get traffic to
 VFs and allow them to be tested; it supports no match fields besides
 ingress port, no actions besides mirred and drop, and no stats.
More matches, actions, and counters will be added in subsequent patches.

Changed in v2:
 - Add missing 'static' on declarations (kernel test robot, sparse)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>