Upon redirection to an uplink VLAN device, emulate vlan push actions
according to the VLAN properties of the VLAN device and redirect to
the uplink.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Changing the prio field of the VLAN is not supported. With
commit 37410902874c ("net/mlx5e: Support VLAN modify action") zero
value indicated "no-change". Allow the vid rewrite if the prio match
is the same as the prio set value.

Fixes: 37410902874c ("net/mlx5e: Support VLAN modify action")
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Rewrite of the packet in the VLAN offset may corrupt the packet if it's
not VLAN tagged. Deny the rewrite in this case.

Fixes: 37410902874c ("net/mlx5e: Support VLAN modify action")
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The headers criteria and value pointers may be either of the inner
packet, if a tunnel exists, or of the outer. Simplify the code by using
helper functions to retrieve them.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

* Now the encapsulation is not supported for mlx5 VFs. When we try to
offload that action, the -EINVAL is returned, but not -EOPNOTSUPP.
This patch changes the returned value and ignore to confuse user.
The command is shown as below [1].

* When max modify header action is zero, we return -EOPNOTSUPP
directly. In this way, we can ignore wrong message info (e.g.
"mlx5: parsed 0 pedit actions, can't do more"). This happens when
offloading pedit actions on mlx(cx4) VFs. The command is shown as below [2].

For example: (p2p1_0 is VF net device)
[1]
$ tc filter add dev p2p1_0 protocol ip  parent ffff: prio 1 flower skip_sw \
    src_mac e4:11:22:33:44:01    \
    action tunnel_key set        \
    src_ip 1.1.1.100        \
    dst_ip 1.1.1.200        \
    dst_port 4789 id 100        \
    action mirred egress redirect dev vxlan0

[2]
$ tc filter add dev p2p1_0 parent ffff: protocol ip prio 1 \
    flower skip_sw dst_mac 00:10:56:fb:64:e8 \
    dst_ip 1.1.1.100 src_ip 1.1.1.200 \
    action pedit ex munge eth src set 00:10:56:b4:5d:20
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

This patch deletes unnecessary setting of the esw_attr->parse_attr
to parse_attr in parse_tc_fdb_actions() because it is already done
by the mlx5e_flow_esw_attr_init() function.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

This patch is a little improvement. Simplify the parse_tc_fdb_actions().
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

If we try to offload decapsulation actions to VFs hw, we get the log [1].
It's not friendly, because the kind of net device is null, and we don't
know what '0' means.

[1] "mlx5_core 0000:05:01.2 vf_0: decapsulation offload is not supported for  net device (0)"
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Delete mutex_init call of a lock that's initialized in inner function.

Fixes: eca8cc38 ("net/mlx5: E-Switch, Refactor offloads flow steering init/cleanup")
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Handle event of power state change in the PCIE slot. When the event
occurs, check if query power state and PCI power fields is supported. If
so, read these fields from MPEIN (management PCIE info) register and
issue a corresponding message.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

This merge commit includes some misc shared code updates from mlx5-next branch needed
for net-next.

1) From Maxim, Remove un-used macros and spinlock from mlx5 code.

2) From Aya, Expose Management PCIE info register layout and add rate limit
print macros.

3) From Tariq, Compilation warning fix in fs_core.c

4) From Vu, Huy and Saeed, Improve mlx5 initialization flow:
The goal is to provide a better logical separation of mlx5 core
device initialization flow and will help to seamlessly support
creating different mlx5 device types such as PF, VF and SF
mlx5 sub-function virtual devices.

Mlx5_core driver needs to separate HCA resources from pci resources.
Its initialize/load/unload will be broken into stages:
1. Initialize common data structures
2. Setup function which initializes pci resources (for PF/VF)
   or some other specific resources for virtual device
3. Initialize software objects according to hardware capabilities
4. Load all mlx5_core components

It is also necessary to detach mlx5_core mdev name/message from pci
device mdev->pdev name/message for a clearer report/debug of
different mlx5 device types.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Action tunnel_key doesn't have a metadata/tunnel for release(decap) action.
Drivers do not dereference entry->tunnel pointer for that action type, so
this behavior doesn't result in a crash at the moment. However, this needs
to be corrected as a preparation for updating hardware offloads API to not
rely on rtnl lock, for which flow_action code will copy the tunnel data to
temporary buffer to prevent concurrent action overwrite from
invalidating/freeing it.

Fixes: 3a7b6861 ("cls_api: add translator to flow_action representation")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: improve genphy_c45_read_lpa

This series improves genphy_c45_read_lpa:
- Use clause 45 standard register / bit to detect link partner autoneg
  capability.
- Consider that lpa register values may be invalid if "autoneg complete"
  bit isn't set.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The link partner advertisement registers are not guaranteed to contain
valid values if autoneg is incomplete. Therefore, if
MDIO_AN_STAT1_COMPLETE isn't set, let's clear all link partner
capability bits. This also avoids unnecessary register reads if link
is down and phylib is in polling mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently mii_lpa_mod_linkmode_lpa_t() checks bit LPA_LPACK to detect
whether link partner supports autoneg. This doesn't work correctly at
least on Aquantia AQCS109 when it negotiates 1000Base-T2 mode.
The "link partner is autoneg-capable" bit as defined by clause 45 is
set however. Better let's switch in general to use the clause 45
standard for link partner autoneg detection.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: add and use new function genphy_read_abilities

Similar to genphy_c45_pma_read_abilities() add a function to dynamically
detect the abilities of a Clause 22 PHY. This is mainly copied from
genphy_config_init(). Main benefit is that PHY drivers no longer have
to specify whether they support GBit or not (provided they keep to
the C22 standard).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use new function genphy_read_abilities(). This allows to remove all
calls to genphy_config_init().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the genphy driver populates phydev->supported like this:
First all possible feature bits are set, then genphy_config_init()
reads the available features from the chip and remove all unsupported
features from phydev->supported. This can be simplified by using
genphy_read_abilities().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to genphy_c45_pma_read_abilities() add a function to dynamically
detect the abilities of a Clause 22 PHY. This is mainly copied from
genphy_config_init().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the following warning:
drivers/net/ethernet/mellanox/mlx5/core//fs_core.c:845:5:
warning: 'err' may be used uninitialized in this function
[-Wmaybe-uninitialized]

No real issue here. This is only a false compiler warning.
The 'err' variable is guaranteed to be init by time of usage.

gcc (GCC) 4.8.5 20150623 (Red Hat 4.8.5-4)
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Expose PRM layout for handling MPEIN (Management PCIE Info). It will be
used in the downstream patch for querying MPEIN via the driver.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Add rate limited print macros for warning and info level. This protects
the system from burst of prints depleting HW resources and spamming dmesg.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Add bar_addr field to store bar-0 address to avoid calling
pci_resource_start with hard-coded bar-0 as parameter.
Also note that different mlx5 device types will have bar_addr
on different bars.

This patch does not change any functionality.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Replace pci dev_err/warn/info messages with mlx5_core_err/warn/info
messages to provide a better report/debug of different mlx5 device types.

This patch does not change any functionality.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Use mlx5_core mdev private name in message instead of using pci dev_name
to provide a better report/debug of different mlx5 device types.

This patch does not change any functionality.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Detach mlx5_core mdev messages from pci device mdev->pdev messages and
provide a better report/debug of different mlx5 device types.

This patch does not change any functionality.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>

Using foundation from previous patches to factor mlx5_load_one flow
into three stages:
1. mlx5_function_setup() from previous patch to setup function
2. mlx5_init_once() from previous patch to init software objects
according to hw caps
3. New mlx5_load() to load mlx5 components

This provides a better logical separation of mlx5 core device
initialization flow and will help to seamlessly support creating different
mlx5 device types such as PF, VF and SF mlx5 sub-function virtual device.

This patch does not change any functionality.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Function setup and teardown procedures are the basic procedure that
each mlx5 pci function should perform to boot up a mlx5 device function
and initialize basic communication with FW, before allocating any higher
level software/firmware resources.

This provides a better logical separation of mlx5 core device
initialization flow and will help to seamlessly support creating different
mlx5 device types such as PF, VF and SF mlx5 sub-function virtual device.

This patch does not change any functionality.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Software structure initialization should be in mdev_init stage.

This provides a better logical separation of mlx5 core device
initialization flow and will help to seamlessly support creating different
mlx5 device types such as PF, VF and SF mlx5 sub-function virtual device.

This patch does not change any functionality.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Separate resources initialization from pci initialization.

This provides a better logical separation of mlx5 core device
initialization flow and will help to seamlessly support creating different
mlx5 device types such as PF, VF and SF mlx5 sub-function virtual device.

This patch does not change any functionality.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

This patch does not change any functionality.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

As there is no user of mlx5_write64 that passes a spinlock to
mlx5_write64, remove this functionality and simplify the function.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

MLX5_*_DOORBELL_LOCK macros provided a way to avoid locking for
mlx5_write64 on 64-bit platforms where it's not necessary. Currently all
calls to mlx5_write64 don't use a spinlock, so the macros became unused.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

We free "ct_info->ct" and then use it on the next line when we pass it
to nf_ct_destroy_timeout().  This patch swaps the order to avoid the use
after free.

Fixes: 06bd2bdf ("openvswitch: Add timeout support to ct action")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yi-Hung Wei <yihung.wei@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make tg3 behave like other drivers and let "ethtool -p" identify the
NIC even when it's in the DOWN state. Before this patch it would get an
error as follows if the NIC was down:

# ip link set down dev em4
# ethtool -p em4
Cannot identify NIC: Resource temporarily unavailable

With this patch ethtool identify works regardless of whether the NIC is up
or down as it does for other drivers.
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

seen with debug config:
drivers/net/macsec.c: In function 'dump_secy':
drivers/net/macsec.c:2597: warning: the frame size of 2216 bytes is larger
than 2048 bytes [-Wframe-larger-than=]

just mark it with noinline_for_stack, this is netlink dump code.

v2: use 'static noinline_for_stack int' consistently

Cc: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Westphal says:

====================
net: move skb->xmit_more to percpu softnet data

Eric Dumazet mentioned we could place xmit_more hint in same
spot as device xmit recursion counter, instead of using
an sk_buff flag bit.

This series places xmit_recursion counter and xmit_more hint
in softnet data, filling a hole.

After this, skb->xmit_more is always zero.  Drivers are converted
to use "netdev_xmit_more()" helper instead.

Last patch removes the skb->xmit_more flag.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This is the last driver using always-0 skb->xmit_more.
Switch it to netdev_xmit_more and remove the now unused xmit_more flag
from sk_buff.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb->xmit_more hint is now always 0, this switches the sfc driver to
use the netdev_xmit_more helper instead.

Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: Edward Cree <ecree@solarflare.com>
Cc: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb->xmit_more hint is now always 0. This switches the mellanox drivers
to the netdev_xmit_more() helper.

Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Boris Pismenny <borisp@mellanox.com>
Cc: Ilya Lesokhin <ilyal@mellanox.com>
Cc: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>