- 06 Nov, 2023 4 commits
-
-
Dario Binacchi authored
Replace 'HFP' with 'HBP'. Fixes: 899f24ed ("drm/panel: Add driver for Novatek NT35510-based panels") Signed-off-by:
Dario Binacchi <dario.binacchi@amarulasolutions.com> Reviewed-by:
Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20231023090613.1694133-1-dario.binacchi@amarulasolutions.com
-
Maíra Canal authored
The previous patch exposed the accumulated amount of active time per client for each V3D queue. But this doesn't provide a global notion of the GPU usage. Therefore, provide the accumulated amount of active time for each V3D queue (BIN, RENDER, CSD, TFU and CACHE_CLEAN), considering all the jobs submitted to the queue, independent of the client. This data is exposed through the sysfs interface, so that if the interface is queried at two different points of time the usage percentage of each of the queues can be calculated. Co-developed-by:
Jose Maria Casanova Crespo <jmcasanova@igalia.com> Signed-off-by:
Maíra Canal <mcanal@igalia.com> Acked-by:
Melissa Wen <mwen@igalia.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230905213416.1290219-3-mcanal@igalia.com
-
Maíra Canal authored
This patch exposes the accumulated amount of active time per client through the fdinfo infrastructure. The amount of active time is exposed for each V3D queue: BIN, RENDER, CSD, TFU and CACHE_CLEAN. In order to calculate the amount of active time per client, a CPU clock is used through the function local_clock(). The point where the jobs has started is marked and is finally compared with the time that the job had finished. Moreover, the number of jobs submitted to each queue is also exposed on fdinfo through the identifier "v3d-jobs-<queue>". Co-developed-by:
-
Tvrtko Ursulin authored
It is better not to lose precision and not revert to 1 MiB size granularity for every size greater than 1 MiB. Sizes in KiB should not be so troublesome to read (and in fact machine parsing is I expect the norm here), they align with other api like /proc/meminfo, and they allow writing tests for the interface without having to embed drm.ko implementation knowledge into them. (Like knowing that minimum buffer size one can use for successful verification has to be 1MiB aligned, and on top account for any pre-existing memory utilisation outside of driver's control.) But probably even more importantly I think that it is just better to show the accurate sizes and not arbitrary lose precision for a little bit of a stretched use case of eyeballing fdinfo text directly. Signed-off-by:
Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Rob Clark <robdclark@gmail.com> Cc: Adrián Larumbe <adrian.larumbe@collabora.com> Cc: steven.price@arm.com Reviewed-by:
Steven Price <steven.price@arm.com> Link: https://lore.kernel.org/r/20230927133843.247957-2-tvrtko.ursulin@linux.intel.comSigned-off-by:
Maxime Ripard <mripard@kernel.org>
-
- 05 Nov, 2023 5 commits
-
-
Tvrtko Ursulin authored
Because a) helper is exported to other parts of the scheduler and b) there isn't a plain drm_sched_wakeup to begin with, I think we can drop the suffix and by doing so separate the intimiate knowledge between the scheduler components a bit better. Signed-off-by:
Luben Tuikov <ltuikov89@gmail.com> Signed-off-by:
-
Tvrtko Ursulin authored
"If ready" is not immediately clear what it means - is the scheduler ready or something else? Drop the suffix, clarify kerneldoc, and employ the same naming scheme as in drm_sched_run_free_queue: - drm_sched_run_job_queue - enqueues if there is something to enqueue *and* scheduler is ready (can queue) - __drm_sched_run_job_queue - low-level helper to simply queue the job Signed-off-by: -
Tvrtko Ursulin authored
The current name makes it sound like helper will free a queue, while what it does is it enqueues the free job worker. Rename it to drm_sched_run_free_queue to align with existing drm_sched_run_job_queue. Despite that creating an illusion there are two queues, while in reality there is only one, at least it creates a consistent naming for the two enqueuing helpers. At the same time simplify the "if done" helper by dropping the suffix and adding a double underscore prefix to the one which just enqueues. Signed-off-by:
-
Tvrtko Ursulin authored
Whether or not there are more jobs to clean up does not depend on the existance of the current job, given both drm_sched_get_finished_job and drm_sched_free_job_queue_if_done take and drop the job list lock. Therefore it is confusing to make it read like there is a dependency. Signed-off-by:
-
Tvrtko Ursulin authored
"Get cleanup job" makes it sound like helper is returning a job which will execute some cleanup, or something, while the kerneldoc itself accurately says "fetch the next _finished_ job". So lets rename the helper to be self documenting. Signed-off-by:
-
- 03 Nov, 2023 2 commits
-
-
Pranjal Ramajor Asha Kanojiya authored
Add support to partially execute a slice which is resized to zero. Executing a zero size slice in a BO should mean that there is no DMA transfers involved but you should still configure doorbell and semaphores. For example consider a BO of size 18K and it is sliced into 3 6K slices and user calls partial execute ioctl with resize as 10K. slice 0 - size is 6k and offset is 0, so resize of 10K will not cut short this slice hence we send the entire slice for execution. slice 1 - size is 6k and offset is 6k, so resize of 10K will cut short this slice and only the first 4k should be DMA along with configuring doorbell and semaphores. slice 2 - size is 6k and offset is 12k, so resize of 10k will cut short this slice and no DMA transfer would be involved but we should would configure doorbell and semaphores. This change begs to change the behavior of 0 resize. Currently, 0 resize partial execute ioctl behaves exactly like execute ioctl i.e. no resize. After this patch all the slice in BO should behave exactly like slice 2 in above example. Refactor copy_partial_exec_reqs() to make it more readable and less complex. Signed-off-by:Pranjal Ramajor Asha Kanojiya <quic_pkanojiy@quicinc.com> Reviewed-by:
Jeffrey Hugo <quic_jhugo@quicinc.com> Signed-off-by:
Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20231027164330.11978-1-quic_jhugo@quicinc.com
-
Carl Vanderlip authored
Current wrapper is right-sized to the message being transferred; however, this is smaller than the structure defining message wrappers since the trailing element is a union of message/transfer headers of various sizes (8 and 32 bytes on 32-bit system where issue was reported). Using the smaller header with a small message (wire_trans_dma_xfer is 24 bytes including header) ends up being smaller than a wrapper with the larger header. There are no accesses outside of the defined size, however they are possible if the larger union member is referenced. Abort messages are outside of hot-path and changing the wrapper struct would require a larger rewrite, so having the memory allocated to the message be 8 bytes too big is acceptable. Reported-by:
kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202310182253.bcb9JcyJ-lkp@intel.com/Signed-off-by:
Carl Vanderlip <quic_carlv@quicinc.com> Reviewed-by:
-
- 02 Nov, 2023 6 commits
-
-
Iago Toral Quiroga authored
This is required to get the V3D module to load with Raspberry Pi 5. Signed-off-by:
Iago Toral Quiroga <itoral@igalia.com> Reviewed-by:
Stefan Wahren <wahrenst@gmx.net> Reviewed-by:
-
Iago Toral Quiroga authored
BCM2712, Raspberry Pi 5's SoC, contains a V3D core. So add its specific compatible to the bindings. Signed-off-by:
Conor Dooley <conor.dooley@microchip.com> Signed-off-by:
-
Iago Toral Quiroga authored
This patch updates a number of register addresses that have been changed in Raspberry Pi 5 (V3D 7.1) and updates the code to use the corresponding registers and addresses based on the actual V3D version. Signed-off-by:
-
Iago Toral Quiroga authored
V3D 7.x takes a new parameter to configure TFU jobs that needs to be provided by user space. Signed-off-by:
-
Thierry Reding authored
The simple-framebuffer device tree bindings document the power-domains property, so make sure that simplefb supports it. This ensures that the power domains remain enabled as long as simplefb is active. v2: - remove unnecessary call to simplefb_detach_genpds() since that's already done automatically by devres - fix crash if power-domains property is missing in DT Signed-off-by:Thierry Reding <treding@nvidia.com> Reviewed-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Thierry Reding authored
The simple-framebuffer bindings specify that the "memory-region" property can be used as an alternative to the "reg" property to define the framebuffer memory used by the display hardware. Implement support for this in the simplefb driver. Reviewed-by:
-
- 01 Nov, 2023 6 commits
-
-
Matthew Brost authored
Add a helper whereby a driver can invoke TDR immediately. v2: - Drop timeout args, rename function, use mod delayed work (Luben) v3: - s/XE/Xe (Luben) - present tense in commit message (Luben) - Adjust comment for drm_sched_tdr_queue_imm (Luben) v4: - Adjust commit message (Luben) Cc: Luben Tuikov <luben.tuikov@amd.com> Signed-off-by:
Matthew Brost <matthew.brost@intel.com> Reviewed-by:
Luben Tuikov <luben.tuikov@amd.com> Link: https://lore.kernel.org/r/20231031032439.1558703-6-matthew.brost@intel.comSigned-off-by:
-
Matthew Brost authored
Also add a lockdep assert to drm_sched_start_timeout. Signed-off-by:
-
Matthew Brost authored
Rather than call free_job and run_job in same work item have a dedicated work item for each. This aligns with the design and intended use of work queues. v2: - Test for DMA_FENCE_FLAG_TIMESTAMP_BIT before setting timestamp in free_job() work item (Danilo) v3: - Drop forward dec of drm_sched_select_entity (Boris) - Return in drm_sched_run_job_work if entity NULL (Boris) v4: - Replace dequeue with peek and invert logic (Luben) - Wrap to 100 lines (Luben) - Update comments for *_queue / *_queue_if_ready functions (Luben) v5: - Drop peek argument, blindly reinit idle (Luben) - s/drm_sched_free_job_queue_if_ready/drm_sched_free_job_queue_if_done (Luben) - Update work_run_job & work_free_job kernel doc (Luben) v6: - Do not move drm_sched_select_entity in file (Luben) Signed-off-by: -
Matthew Brost authored
In Xe, the new Intel GPU driver, a choice has made to have a 1 to 1 mapping between a drm_gpu_scheduler and drm_sched_entity. At first this seems a bit odd but let us explain the reasoning below. 1. In Xe the submission order from multiple drm_sched_entity is not guaranteed to be the same completion even if targeting the same hardware engine. This is because in Xe we have a firmware scheduler, the GuC, which allowed to reorder, timeslice, and preempt submissions. If a using shared drm_gpu_scheduler across multiple drm_sched_entity, the TDR falls apart as the TDR expects submission order == completion order. Using a dedicated drm_gpu_scheduler per drm_sched_entity solve this problem. 2. In Xe submissions are done via programming a ring buffer (circular buffer), a drm_gpu_scheduler provides a limit on number of jobs, if the limit of number jobs is set to RING_SIZE / MAX_SIZE_PER_JOB we get flow control on the ring for free. A problem with this design is currently a drm_gpu_scheduler uses a kthread for submission / job cleanup. This doesn't scale if a large number of drm_gpu_scheduler are used. To work around the scaling issue, use a worker rather than kthread for submission / job cleanup. v2: - (Rob Clark) Fix msm build - Pass in run work queue v3: - (Boris) don't have loop in worker v4: - (Tvrtko) break out submit ready, stop, start helpers into own patch v5: - (Boris) default to ordered work queue v6: - (Luben / checkpatch) fix alignment in msm_ringbuffer.c - (Luben) s/drm_sched_submit_queue/drm_sched_wqueue_enqueue - (Luben) Update comment for drm_sched_wqueue_enqueue - (Luben) Positive check for submit_wq in drm_sched_init - (Luben) s/alloc_submit_wq/own_submit_wq v7: - (Luben) s/drm_sched_wqueue_enqueue/drm_sched_run_job_queue v8: - (Luben) Adjust var names / comments Signed-off-by:
-
Matthew Brost authored
Add scheduler wqueue ready, stop, and start helpers to hide the implementation details of the scheduler from the drivers. v2: - s/sched_wqueue/sched_wqueue (Luben) - Remove the extra white line after the return-statement (Luben) - update drm_sched_wqueue_ready comment (Luben) Cc: Luben Tuikov <luben.tuikov@amd.com> Signed-off-by:
-
Christian König authored
When a fence signals there is a very small race window where the timestamp isn't updated yet. sync_file solves this by busy waiting for the timestamp to appear, but on other ocassions didn't handled this correctly. Provide a dma_fence_timestamp() helper function for this and use it in all appropriate cases. Another alternative would be to grab the spinlock when that happens. v2 by teddy: add a wait parameter to wait for the timestamp to show up, in case the accurate timestamp is needed and/or the timestamp is not based on ktime (e.g. hw timestamp) v3 chk: drop the parameter again for unified handling Signed-off-by:
Yunxiang Li <Yunxiang.Li@amd.com> Signed-off-by:
Christian König <christian.koenig@amd.com> Fixes: 1774baa6 ("drm/scheduler: Change scheduled fence track v2") Reviewed-by:
Alex Deucher <alexander.deucher@amd.com> CC: stable@vger.kernel.org Link: https://patchwork.freedesktop.org/patch/msgid/20230929104725.2358-1-christian.koenig@amd.com
-
- 31 Oct, 2023 10 commits
-
-
Jacek Lawrynowicz authored
VPU was rebranded as NPU (Neural Processing Unit) so user facing strings have to be updated but the code remains as is and the module is still called intel_vpu.ko. Signed-off-by:
Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com> Reviewed-by:
-
Jacek Lawrynowicz authored
CMD_SYNC does not need any args as we poll for completion anyway. Signed-off-by:
-
Karol Wachowski authored
Previously using dma_alloc_wc() API we created cache coherent (mapped as write-back) mappings. Because we disable MMU600 snooping it was required to do costly page walk and cache flushes after each page table modification. With write-combined buffers it's possible to do a single write memory barrier to flush write-combined buffer to memory which simplifies the driver and significantly reduce time of map/unmap operations. Mapping time of 255 MB is reduced from 2.5 ms to 500 us. Signed-off-by:
Karol Wachowski <karol.wachowski@linux.intel.com> Reviewed-by:
-
Karol Wachowski authored
Add checking of error reason bits in IVPU_MMU_CMDQ_CONS register when waiting for consumer timeout occurred. Signed-off-by:
-
Stanislaw Gruszka authored
Waking up process, which wait for particular condition, will go to sleep again on wake_up() if the condition is not met. Add abort flag to wake up IPC receivers, which will finish with -ECANCELED error. This is only needed for reset, run time power management prevent to suspend VPU when there is pending IPC processing or pending job. Reviewed-by:
-
Stanislaw Gruszka authored
Stop job_done thread when going to suspend. Use kthread_park() instead of kthread_stop() to avoid memory allocation and potential failure on resume. Use separate function as thread wake up condition. Use spin lock to assure rx_msg_list is properly protected against concurrent access. This avoid race condition when the rx_msg_list list is modified and read in ivpu_ipc_recive() at the same time. Reviewed-by:
-
Stanislaw Gruszka authored
We should not leave device half enabled if there is failure somewhere it power up sequence. Fix device init and resume paths. Reviewed-by:
-
Krystian Pradzynski authored
Profiling freq is a debug firmware feature. It switches default clock to higher resolution for fine-grained and more accurate firmware task profiling. We already configure it during boot up of VPU4. Add debugfs knob and helpers per HW generation that allow to change it. For vpu37xx the implementation is empty as profiling frequency can only be changed on VPU4 or newer. Signed-off-by:
Krystian Pradzynski <krystian.pradzynski@linux.intel.com> Reviewed-by:
-
Tomi Valkeinen authored
This reverts commit 250aa229. The DMA-fence annotations cause a lockdep warning (see below). As per https://patchwork.freedesktop.org/patch/462170/ it sounds like the annotations don't work correctly. ====================================================== WARNING: possible circular locking dependency detected 6.5.0-rc2+ #2 Not tainted ------------------------------------------------------ kmstest/219 is trying to acquire lock: c4705838 (&hdmi->lock){+.+.}-{3:3}, at: hdmi5_bridge_mode_set+0x1c/0x50 but task is already holding lock: c11e1128 (dma_fence_map){++++}-{0:0}, at: omap_atomic_commit_tail+0x14/0xbc which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (dma_fence_map){++++}-{0:0}: __dma_fence_might_wait+0x48/0xb4 dma_resv_lockdep+0x1b8/0x2bc do_one_initcall+0x68/0x3b0 kernel_init_freeable+0x260/0x34c kernel_init+0x14/0x140 ret_from_fork+0x14/0x28 -> #1 (fs_reclaim){+.+.}-{0:0}: fs_reclaim_acquire+0x70/0xa8 __kmem_cache_alloc_node+0x3c/0x368 kmalloc_trace+0x28/0x58 _drm_do_get_edid+0x7c/0x35c hdmi5_bridge_get_edid+0xc8/0x1ac drm_bridge_connector_get_modes+0x64/0xc0 drm_helper_probe_single_connector_modes+0x170/0x528 drm_client_modeset_probe+0x208/0x1334 __drm_fb_helper_initial_config_and_unlock+0x30/0x548 omap_fbdev_client_hotplug+0x3c/0x6c drm_client_register+0x58/0x94 pdev_probe+0x544/0x6b0 platform_probe+0x58/0xbc really_probe+0xd8/0x3fc __driver_probe_device+0x94/0x1f4 driver_probe_device+0x2c/0xc4 __device_attach_driver+0xa4/0x11c bus_for_each_drv+0x84/0xdc __device_attach+0xac/0x20c bus_probe_device+0x8c/0x90 device_add+0x588/0x7e0 platform_device_add+0x110/0x24c platform_device_register_full+0x108/0x15c dss_bind+0x90/0xc0 try_to_bring_up_aggregate_device+0x1e0/0x2c8 __component_add+0xa4/0x174 hdmi5_probe+0x1c8/0x270 platform_probe+0x58/0xbc really_probe+0xd8/0x3fc __driver_probe_device+0x94/0x1f4 driver_probe_device+0x2c/0xc4 __device_attach_driver+0xa4/0x11c bus_for_each_drv+0x84/0xdc __device_attach+0xac/0x20c bus_probe_device+0x8c/0x90 deferred_probe_work_func+0x8c/0xd8 process_one_work+0x2ac/0x6e4 worker_thread+0x30/0x4ec kthread+0x100/0x124 ret_from_fork+0x14/0x28 -> #0 (&hdmi->lock){+.+.}-{3:3}: __lock_acquire+0x145c/0x29cc lock_acquire.part.0+0xb4/0x258 __mutex_lock+0x90/0x950 mutex_lock_nested+0x1c/0x24 hdmi5_bridge_mode_set+0x1c/0x50 drm_bridge_chain_mode_set+0x48/0x5c crtc_set_mode+0x188/0x1d0 omap_atomic_commit_tail+0x2c/0xbc commit_tail+0x9c/0x188 drm_atomic_helper_commit+0x158/0x18c drm_atomic_commit+0xa4/0xe8 drm_mode_atomic_ioctl+0x9a4/0xc38 drm_ioctl+0x210/0x4a8 sys_ioctl+0x138/0xf00 ret_fast_syscall+0x0/0x1c other info that might help us debug this: Chain exists of: &hdmi->lock --> fs_reclaim --> dma_fence_map Possible unsafe locking scenario: CPU0 CPU1 ---- ---- rlock(dma_fence_map); lock(fs_reclaim); lock(dma_fence_map); lock(&hdmi->lock); *** DEADLOCK *** 3 locks held by kmstest/219: #0: f1011de4 (crtc_ww_class_acquire){+.+.}-{0:0}, at: drm_mode_atomic_ioctl+0xf0/0xc38 #1: c47059c8 (crtc_ww_class_mutex){+.+.}-{3:3}, at: modeset_lock+0xf8/0x230 #2: c11e1128 (dma_fence_map){++++}-{0:0}, at: omap_atomic_commit_tail+0x14/0xbc stack backtrace: CPU: 1 PID: 219 Comm: kmstest Not tainted 6.5.0-rc2+ #2 Hardware name: Generic DRA74X (Flattened Device Tree) unwind_backtrace from show_stack+0x10/0x14 show_stack from dump_stack_lvl+0x58/0x70 dump_stack_lvl from check_noncircular+0x164/0x198 check_noncircular from __lock_acquire+0x145c/0x29cc __lock_acquire from lock_acquire.part.0+0xb4/0x258 lock_acquire.part.0 from __mutex_lock+0x90/0x950 __mutex_lock from mutex_lock_nested+0x1c/0x24 mutex_lock_nested from hdmi5_bridge_mode_set+0x1c/0x50 hdmi5_bridge_mode_set from drm_bridge_chain_mode_set+0x48/0x5c drm_bridge_chain_mode_set from crtc_set_mode+0x188/0x1d0 crtc_set_mode from omap_atomic_commit_tail+0x2c/0xbc omap_atomic_commit_tail from commit_tail+0x9c/0x188 commit_tail from drm_atomic_helper_commit+0x158/0x18c drm_atomic_helper_commit from drm_atomic_commit+0xa4/0xe8 drm_atomic_commit from drm_mode_atomic_ioctl+0x9a4/0xc38 drm_mode_atomic_ioctl from drm_ioctl+0x210/0x4a8 drm_ioctl from sys_ioctl+0x138/0xf00 sys_ioctl from ret_fast_syscall+0x0/0x1c Exception stack(0xf1011fa8 to 0xf1011ff0) 1fa0: 00466d58 be9ab510 00000003 c03864bc be9ab510 be9ab4e0 1fc0: 00466d58 be9ab510 c03864bc 00000036 00466ef0 00466fc0 00467020 00466f20 1fe0: b6bc7ef4 be9ab4d0 b6bbbb00 b6cb2cc0 Fixes: 250aa229 ("drm/omapdrm: Annotate dma-fence critical section in commit path") Reviewed-by:
Aradhya Bhatia <a-bhatia1@ti.com> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230920-dma-fence-annotation-revert-v1-2-7ebf6f7f5bf6@ideasonboard.com
-
Tomi Valkeinen authored
This reverts commit 4d56a4f0. The DMA-fence annotations cause a lockdep warning (see below). As per https://patchwork.freedesktop.org/patch/462170/ it sounds like the annotations don't work correctly. ====================================================== WARNING: possible circular locking dependency detected 6.6.0-rc2+ #1 Not tainted ------------------------------------------------------ kmstest/733 is trying to acquire lock: ffff8000819377f0 (fs_reclaim){+.+.}-{0:0}, at: __kmem_cache_alloc_node+0x58/0x2d4 but task is already holding lock: ffff800081a06aa0 (dma_fence_map){++++}-{0:0}, at: tidss_atomic_commit_tail+0x20/0xc0 [tidss] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (dma_fence_map){++++}-{0:0}: __dma_fence_might_wait+0x5c/0xd0 dma_resv_lockdep+0x1a4/0x32c do_one_initcall+0x84/0x2fc kernel_init_freeable+0x28c/0x4c4 kernel_init+0x24/0x1dc ret_from_fork+0x10/0x20 -> #1 (mmu_notifier_invalidate_range_start){+.+.}-{0:0}: fs_reclaim_acquire+0x70/0xe4 __kmem_cache_alloc_node+0x58/0x2d4 kmalloc_trace+0x38/0x78 __kthread_create_worker+0x3c/0x150 kthread_create_worker+0x64/0x8c workqueue_init+0x1e8/0x2f0 kernel_init_freeable+0x11c/0x4c4 kernel_init+0x24/0x1dc ret_from_fork+0x10/0x20 -> #0 (fs_reclaim){+.+.}-{0:0}: __lock_acquire+0x1370/0x20d8 lock_acquire+0x1e8/0x308 fs_reclaim_acquire+0xd0/0xe4 __kmem_cache_alloc_node+0x58/0x2d4 __kmalloc_node_track_caller+0x58/0xf0 kmemdup+0x34/0x60 regmap_bulk_write+0x64/0x2c0 tc358768_bridge_pre_enable+0x8c/0x12d0 [tc358768] drm_atomic_bridge_call_pre_enable+0x68/0x80 [drm] drm_atomic_bridge_chain_pre_enable+0x50/0x158 [drm] drm_atomic_helper_commit_modeset_enables+0x164/0x264 [drm_kms_helper] tidss_atomic_commit_tail+0x58/0xc0 [tidss] commit_tail+0xa0/0x188 [drm_kms_helper] drm_atomic_helper_commit+0x1a8/0x1c0 [drm_kms_helper] drm_atomic_commit+0xa8/0xe0 [drm] drm_mode_atomic_ioctl+0x9ec/0xc80 [drm] drm_ioctl_kernel+0xc4/0x170 [drm] drm_ioctl+0x234/0x4b0 [drm] drm_compat_ioctl+0x110/0x12c [drm] __arm64_compat_sys_ioctl+0x128/0x150 invoke_syscall+0x48/0x110 el0_svc_common.constprop.0+0x40/0xe0 do_el0_svc_compat+0x1c/0x38 el0_svc_compat+0x48/0xb4 el0t_32_sync_handler+0xb0/0x138 el0t_32_sync+0x194/0x198 other info that might help us debug this: Chain exists of: fs_reclaim --> mmu_notifier_invalidate_range_start --> dma_fence_map Possible unsafe locking scenario: CPU0 CPU1 ---- ---- rlock(dma_fence_map); lock(mmu_notifier_invalidate_range_start); lock(dma_fence_map); lock(fs_reclaim); *** DEADLOCK *** 3 locks held by kmstest/733: #0: ffff800082e5bba0 (crtc_ww_class_acquire){+.+.}-{0:0}, at: drm_mode_atomic_ioctl+0x118/0xc80 [drm] #1: ffff000004224c88 (crtc_ww_class_mutex){+.+.}-{3:3}, at: modeset_lock+0xdc/0x1a0 [drm] #2: ffff800081a06aa0 (dma_fence_map){++++}-{0:0}, at: tidss_atomic_commit_tail+0x20/0xc0 [tidss] stack backtrace: CPU: 0 PID: 733 Comm: kmstest Not tainted 6.6.0-rc2+ #1 Hardware name: Toradex Verdin AM62 on Verdin Development Board (DT) Call trace: dump_backtrace+0x98/0x118 show_stack+0x18/0x24 dump_stack_lvl+0x60/0xac dump_stack+0x18/0x24 print_circular_bug+0x288/0x368 check_noncircular+0x168/0x17c __lock_acquire+0x1370/0x20d8 lock_acquire+0x1e8/0x308 fs_reclaim_acquire+0xd0/0xe4 __kmem_cache_alloc_node+0x58/0x2d4 __kmalloc_node_track_caller+0x58/0xf0 kmemdup+0x34/0x60 regmap_bulk_write+0x64/0x2c0 tc358768_bridge_pre_enable+0x8c/0x12d0 [tc358768] drm_atomic_bridge_call_pre_enable+0x68/0x80 [drm] drm_atomic_bridge_chain_pre_enable+0x50/0x158 [drm] drm_atomic_helper_commit_modeset_enables+0x164/0x264 [drm_kms_helper] tidss_atomic_commit_tail+0x58/0xc0 [tidss] commit_tail+0xa0/0x188 [drm_kms_helper] drm_atomic_helper_commit+0x1a8/0x1c0 [drm_kms_helper] drm_atomic_commit+0xa8/0xe0 [drm] drm_mode_atomic_ioctl+0x9ec/0xc80 [drm] drm_ioctl_kernel+0xc4/0x170 [drm] drm_ioctl+0x234/0x4b0 [drm] drm_compat_ioctl+0x110/0x12c [drm] __arm64_compat_sys_ioctl+0x128/0x150 invoke_syscall+0x48/0x110 el0_svc_common.constprop.0+0x40/0xe0 do_el0_svc_compat+0x1c/0x38 el0_svc_compat+0x48/0xb4 el0t_32_sync_handler+0xb0/0x138 el0t_32_sync+0x194/0x198 Fixes: 4d56a4f0 ("drm/tidss: Annotate dma-fence critical section in commit path") Reviewed-by:
-
- 30 Oct, 2023 7 commits
-
-
Steven Price authored
sg_page_iter_page() doesn't return an error code, so the IS_ERR() check is wrong and the error path will never be executed. This also allows simplifying the code to remove the local variable 'page'. CC: Adrián Larumbe <adrian.larumbe@collabora.com> Reported-by:
Dan Carpenter <dan.carpenter@linaro.org> Closes: https://lore.kernel.org/r/376713ff-9a4f-4ea3-b097-fb5efb685d95@moroto.mountainSigned-off-by:
Adrián Larumbe <adrian.larumbe@collabora.com> Tested-by:
-
Maíra Canal authored
Currently, we are only warning the user if the BIN or RENDER jobs don't finish before we unregister V3D. We must wait for all jobs to finish before unregistering. Therefore, warn the user if TFU or CSD jobs are not done by the time the driver is unregistered. Signed-off-by:
Maíra Canal <mairacanal@riseup.net> Link: https://patchwork.freedesktop.org/patch/msgid/20231023105927.101502-1-mcanal@igalia.com
-
Andrzej Kacprowski authored
Currently the VPU firmware prepares for D0i3 every time the VPU is entering D0i2 Idle state. This is not optimal as we might not enter D0i3 every time we enter D0i2 Idle and this preparation is quite costly. This optimization moves D0i3 preparation to a dedicated message sent from the host driver only when the driver is about to enter D0i3 - this reduces power consumption and latency for certain workloads, for example audio workloads that submit inference every 10 ms. The VPU needs non zero time to enter IDLE state after responding to D0i3 entry message. If the driver does not wait for the VPU to enter IDLE state it could cause warm boot failures. Signed-off-by:
Andrzej Kacprowski <andrzej.kacprowski@linux.intel.com> Reviewed-by:
-
Stanislaw Gruszka authored
Print warning if VPUIP is not idle during power down. Use warn log level also when we fail to enter reset state as this is not really an error but unexpected behavior. Reviewed-by:
-
Karol Wachowski authored
Split ivpu_ipc_send_receive() implementation to have a version that does not call pm_runtime_resume_and_get(). That implementation can be invoked when device is up and runtime resume is prohibited (for example at the end of boot sequence). The new function will be used for D0i3 entry IPC message addition in the separate change. Signed-off-by:
-
Andrzej Kacprowski authored
The firmware needs to know the time spent in D0i3/D3 to calculate telemetry data. The D0i3/D3 residency time is calculated by the driver and passed to the firmware in the boot parameters. The driver also passes VPU perf counter value captured right before entering D0i3 - this allows the VPU firmware to generate monotonic timestamps for the logs. Signed-off-by:
-
Andrzej Kacprowski authored
The driver needs to capture the D0i3 entry timestamp to calculate D0i3 residency time. The D0i3 residency time and the VPU timestamp are passed to the firmware at D0i3 exit (warm boot). Signed-off-by:
-
