Move queue enable and disable code to separate functions. This way the
activation and deactivation of the queues are defined actions, which can
be used in future execution paths.

This functions will be used for the queue reconfiguration at runtime,
which is necessary for XSK zero-copy support.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Make initialization of TX and RX queues less dynamic by moving some
initialization from netdev open/close to device probing.

Additionally, move some initialization code to separate functions to
enable future use in other execution paths.

This is done as preparation for queue reconfigure at runtime, which is
necessary for XSK zero-copy support.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

TX/RX ring size is static and power of 2 to enable compiler to optimize
modulo operation to mask operation. Make this optimization already in
the code and don't rely on the compiler.

CPU utilisation during high packet rate has not changed. So no
performance improvement has been measured. But it is best practice to
prevent modulo operations.
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Up to 4 LEDs can be attached to the PHY, add support for setting
brightness manually.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230424134625.303957-1-alexander.stein@ew.tq-group.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

'reg' is always encoded in 32 bits, thus it has to be read using the
function with the corresponding bit width.

Fixes: 01e5b728 ("net: phy: Add a binding for PHY LEDs")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230424141648.317944-1-alexander.stein@ew.tq-group.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Smatch complains that:
nfcsim_debugfs_init_dev() warn: 'dev_dir' is an error pointer or valid

According to the documentation of the debugfs_create_dir() function,
there is no need to check the return value of this function.
Just delete the dead code.
Signed-off-by: Jianuo Kuang <u202110722@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230424024140.34607-1-u202110722@hust.edu.cnSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pointer variables of void * type do not require type cast.
Signed-off-by: wuych <yunchuan@nfschina.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230424101550.664319-1-yunchuan@nfschina.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

SET_COALESCE may change operation mode and parameters in one call.
Changing operation mode may cause the driver to reset the parameter
values to what is a reasonable default for new operation mode.

Since driver does not know which parameters come from user and which
are echoed back from ->get, driver may ignore the parameters when
switching operation modes.

This used to be inevitable for ioctl() but in netlink we know which
parameters are actually specified by the user.

We could inform which parameters were set by the user but this would
lead to a lot of code duplication in the drivers. Instead try to call
the drivers twice if both mode and params are changed. The set method
already checks if any params need updating so in case the driver did
the right thing the first time around - there will be no second call
to it's ->set method (only an extra call to ->get()).

For mlx5 for example before this patch we'd see:

 # ethtool -C eth0 adaptive-rx on  adaptive-tx on
 # ethtool -C eth0 adaptive-rx off adaptive-tx off \
		   tx-usecs 123 rx-usecs 123
 Adaptive RX: off  TX: off
 rx-usecs: 3
 rx-frames: 32
 tx-usecs: 16
 tx-frames: 32
 [...]

After the change:

 # ethtool -C eth0 adaptive-rx on  adaptive-tx on
 # ethtool -C eth0 adaptive-rx off adaptive-tx off \
		   tx-usecs 123 rx-usecs 123
 Adaptive RX: off  TX: off
 rx-usecs: 123
 rx-frames: 32
 tx-usecs: 123
 tx-frames: 32
 [...]

This only works for netlink, so it's a small discrepancy between
netlink and ioctl(). Since we anticipate most users to move to
netlink I believe it's worth making their lives easier.

Link: https://lore.kernel.org/r/20230420233302.944382-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Haiyang Zhang says:

====================
Update coding style and check alloc_frag

Follow up patches for the jumbo frame support.

As suggested by Jakub Kicinski, update coding style, and check napi_alloc_frag
for possible fallback to single pages.
====================

Link: https://lore.kernel.org/r/1682096818-30056-1-git-send-email-haiyangz@microsoft.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

netdev/napi_alloc_frag() may fall back to single page which is smaller
than the requested size.
Add error checking to avoid memory overwritten.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Rename mana_refill_rxoob for naming consistency.
And remove some empty lines between function call and error
checking.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Lorenzo Bianconi says:

====================
add page_pool support for page recycling in veth driver

Introduce page_pool support in veth driver in order to recycle pages in
veth_convert_skb_to_xdp_buff routine and avoid reallocating the skb through
the page allocator when we run a xdp program on the device and we receive
skbs from the stack.
====================

Link: https://lore.kernel.org/r/cover.1682188837.git.lorenzo@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Introduce page_pool stats support to report info about local page_pool
through ethtool
Tested-by: Maryam Tahhan <mtahhan@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Introduce page_pool support in veth driver in order to recycle pages
in veth_convert_skb_to_xdp_buff routine and avoid reallocating the skb
through the page allocator.
The patch has been tested sending tcp traffic to a veth pair where the
remote peer is running a simple xdp program just returning xdp_pass:

veth upstream codebase:
MTU 1500B: ~ 8Gbps
MTU 8000B: ~ 13.9Gbps

veth upstream codebase + pp support:
MTU 1500B: ~ 9.2Gbps
MTU 8000B: ~ 16.2Gbps
Tested-by: Maryam Tahhan <mtahhan@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pablo Neira Ayuso says:

====================
Netfilter/IPVS updates for net-next

1) Reduce jumpstack footprint: Stash chain in last rule marker in blob for
   tracing. Remove last rule and chain from jumpstack. From Florian Westphal.

2) nf_tables validates all tables before committing the new rules.
   Unfortunately, this has two drawbacks:

   - Since addition of the transaction mutex pernet state gets written to
     outside of the locked section from the cleanup callback, this is
     wrong so do this cleanup directly after table has passed all checks.

   - Revalidate tables that saw no changes. This can be avoided by
     keeping the validation state per table, not per netns.

   From Florian Westphal.

3) Get rid of a few redundant pointers in the traceinfo structure.
   The three removed pointers are used in the expression evaluation loop,
   so gcc keeps them in registers. Passing them to the (inlined) helpers
   thus doesn't increase nft_do_chain text size, while stack is reduced
   by another 24 bytes on 64bit arches. From Florian Westphal.

4) IPVS cleanups in several ways without implementing any functional
   changes, aside from removing some debugging output:

   - Update width of source for ip_vs_sync_conn_options
     The operation is safe, use an annotation to describe it properly.

   - Consistently use array_size() in ip_vs_conn_init()
     It seems better to use helpers consistently.

   - Remove {Enter,Leave}Function. These seem to be well past their
     use-by date.

   - Correct spelling in comments.

   From Simon Horman.

5) Extended netlink error report for netdevice in flowtables and
   netdev/chains. Allow for incrementally add/delete devices to netdev
   basechain. Allow to create netdev chain without device.

* tag 'nf-next-23-04-22' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
  netfilter: nf_tables: allow to create netdev chain without device
  netfilter: nf_tables: support for deleting devices in an existing netdev chain
  netfilter: nf_tables: support for adding new devices to an existing netdev chain
  netfilter: nf_tables: rename function to destroy hook list
  netfilter: nf_tables: do not send complete notification of deletions
  netfilter: nf_tables: extended netlink error reporting for netdevice
  ipvs: Correct spelling in comments
  ipvs: Remove {Enter,Leave}Function
  ipvs: Consistently use array_size() in ip_vs_conn_init()
  ipvs: Update width of source for ip_vs_sync_conn_options
  netfilter: nf_tables: do not store rule in traceinfo structure
  netfilter: nf_tables: do not store verdict in traceinfo structure
  netfilter: nf_tables: do not store pktinfo in traceinfo structure
  netfilter: nf_tables: remove unneeded conditional
  netfilter: nf_tables: make validation state per table
  netfilter: nf_tables: don't write table validation state without mutex
  netfilter: nf_tables: don't store chain address on jump
  netfilter: nf_tables: don't store address of last rule on jump
  netfilter: nf_tables: merge nft_rules_old structure and end of ruleblob marker
====================

Link: https://lore.kernel.org/r/20230421235021.216950-1-pablo@netfilter.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'for-net-next-2023-04-23' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

bluetooth-next pull request for net-next:

 - Introduce devcoredump support
 - Add support for Realtek RTL8821CS, RTL8851B, RTL8852BS
 - Add support for Mediatek MT7663, MT7922
 - Add support for NXP w8997
 - Add support for Actions Semi ATS2851
 - Add support for QTI WCN6855
 - Add support for Marvell 88W8997

This makes sure hci_cmd_sync_queue only queue new work if HCI_RUNNING
has been set otherwise there is a risk of commands being sent while
turning off.

Because hci_cmd_sync_queue can no longer queue work while HCI_RUNNING is
not set it cannot be used to power on adapters so instead
hci_cmd_sync_submit is introduced which bypass the HCI_RUNNING check, so
it behaves like the old implementation.

Link: https://lore.kernel.org/all/CAB4PzUpDMvdc8j2MdeSAy1KkAE-D3woprCwAdYWeOc-3v3c9Sw@mail.gmail.com/Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

WCN6855 will report memdump via ACL data or HCI event when
it get crashed, so we collect memdump to debug firmware.
Signed-off-by: Tim Jiang <quic_tjiang@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This enables flow control before checking for bootloader signature and
deciding whether FW download is needed or not. In case of V1 bootloader
chips w8987 and w8997, it is observed that if WLAN FW is downloaded first
and power save is enabled in wlan core, bootloader signatures are not
emitted by the BT core when the chip is put to sleep. As a result, the
driver skips FW download and subsequent HCI commands get timeout errors
in dmesg as shown below:

[  112.898867] Bluetooth: hci0: Opcode 0x c03 failed: -110
[  114.914865] Bluetooth: hci0: Setting baudrate failed (-110)
[  116.930856] Bluetooth: hci0: Setting wake-up method failed (-110)

By enabling the flow control, the host enables its RTS pin, and an
interrupt in chip's UART peripheral causes the bootloader to wake up,
enabling the bootloader signatures, which then helps in downloading
the bluetooth FW file.

This changes all instances of 0/1 for serdev_device_set_flow_control()
to false/true.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Some of the sync commands might take a long time to complete, e.g.
LE Create Connection when the peer device isn't responding might take
20 seconds before it times out. If suspend command is issued during
this time, it will need to wait for completion since both commands are
using the same sync lock.

This patch cancel any running sync commands before attempting to
suspend or adapter power off.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add the support for RTL8851B BT controller on USB interface.
The necessary firmware will be submitted to linux-firmware project.

Note that the Bluetooth devices WITH the VID=0x0bda would be set the
feature quirk in btrtl_setup_realtek(). It's able to ignore the
feature flag set for the specific VID and PID in blacklist_table[] of
btusb.c. (check [1])

If Realtek Bluetooth chips WITHOUT the VID=0x0bda, it shall be added
the feature flag for the specific VID and PID in blacklist_table[] of
btusb.c. (check [2])

[1] '9ab9235f ("Bluetooth: btrtl: Enable WBS for the specific
    Realtek devices")'
[2] '73280f13 ("Bluetooth: btusb: Add the more support IDs for
    Realtek RTL8822CE")'

The device info from /sys/kernel/debug/usb/devices as below.

T:  Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 33 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0bda ProdID=b851 Rev= 0.00
S:  Manufacturer=Realtek
S:  Product=802.11ax WLAN Adapter
S:  SerialNumber=00E04C885A01
C:* #Ifs= 3 Cfg#= 1 Atr=80 MxPwr=500mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 8 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=0a(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=0b(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=0c(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This fixes the following sparse warnings:

   drivers/bluetooth/btnxpuart.c:681:23: sparse: sparse:
   restricted __le16 degrades to integer
   drivers/bluetooth/btnxpuart.c:690:82: sparse:
   sparse: incorrect type in argument 2 (different base types)
   @@     expected unsigned short [usertype] req_len
   @@     got restricted __le16 [usertype] len @@
   drivers/bluetooth/btnxpuart.c:690:82: sparse:
   expected unsigned short [usertype] req_len
   drivers/bluetooth/btnxpuart.c:690:82: sparse:
   got restricted __le16 [usertype] len
   drivers/bluetooth/btnxpuart.c:694:84: sparse:
   sparse: incorrect type in argument 2 (different base types)
   @@     expected unsigned short [usertype] req_len
   @@     got restricted __le16 [usertype] len @@
   drivers/bluetooth/btnxpuart.c:694:84: sparse:
   expected unsigned short [usertype] req_len
   drivers/bluetooth/btnxpuart.c:694:84: sparse:
   got restricted __le16 [usertype] len
   drivers/bluetooth/btnxpuart.c:708:23: sparse:
   sparse: incorrect type in assignment (different base types)
   @@     expected unsigned int [usertype] requested_len
   @@     got restricted __le16 [usertype] len @@
   drivers/bluetooth/btnxpuart.c:708:23: sparse:
   expected unsigned int [usertype] requested_len
   drivers/bluetooth/btnxpuart.c:708:23: sparse:
   got restricted __le16 [usertype] len
   drivers/bluetooth/btnxpuart.c:787:78: sparse:
   sparse: incorrect type in argument 2 (different base types)
   @@     expected unsigned short [usertype] chipid
   @@     got restricted __le16 [usertype] chip_id @@
   drivers/bluetooth/btnxpuart.c:787:78: sparse:
   expected unsigned short [usertype] chipid
   drivers/bluetooth/btnxpuart.c:787:78: sparse:
   got restricted __le16 [usertype] chip_id
   drivers/bluetooth/btnxpuart.c:810:74: sparse:
   sparse: incorrect type in argument 2 (different base types)
   @@     expected unsigned short [usertype] req_len
   @@     got restricted __le16 [usertype] len @@
   drivers/bluetooth/btnxpuart.c:810:74: sparse:
   expected unsigned short [usertype] req_len
   drivers/bluetooth/btnxpuart.c:810:74: sparse:
   got restricted __le16 [usertype] len
   drivers/bluetooth/btnxpuart.c:815:76: sparse:
   sparse: incorrect type in argument 2 (different base types)
   @@     expected unsigned short [usertype] req_len
   @@     got restricted __le16 [usertype] len @@
   drivers/bluetooth/btnxpuart.c:815:76: sparse:
   expected unsigned short [usertype] req_len
   drivers/bluetooth/btnxpuart.c:815:76: sparse:
   got restricted __le16 [usertype] len
   drivers/bluetooth/btnxpuart.c:834:16: sparse:
   sparse: restricted __le32 degrades to integer
   drivers/bluetooth/btnxpuart.c:843:55: sparse:
   sparse: restricted __le32 degrades to integer
   drivers/bluetooth/btnxpuart.c:844:36: sparse:
   sparse: incorrect type in argument 3 (different base types)
   @@     expected unsigned long [usertype]
   @@     got restricted __le16 [usertype] len @@
   drivers/bluetooth/btnxpuart.c:844:36: sparse:
   expected unsigned long [usertype]
   drivers/bluetooth/btnxpuart.c:844:36: sparse:
   got restricted __le16 [usertype] len
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202304160736.Tsa0zTBU-lkp@intel.com/Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Realtek changed the format of the firmware file as v2. The driver
should implement the patch to extract the firmware data from the
firmware file. The future chips must apply this patch for firmware loading.
This patch is compatible with the both previous format and v2 as well.
Signed-off-by: Allen Chen <allen_chen@realsil.com.cn>
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Tested-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

API hci_devcd_init() stores its u32 type parameter @dump_size into
skb, but it does not specify which byte order is used to store the
integer, let us take little endian to store and parse the integer.

Fixes: f5cc609d09d4 ("Bluetooth: Add support for hci devcoredump")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Previously, capability was checked using capable(), which verified that the
caller of the ioctl system call had the required capability. In addition,
the result of the check would be stored in the HCI_SOCK_TRUSTED flag,
making it persistent for the socket.

However, malicious programs can abuse this approach by deliberately sharing
an HCI socket with a privileged task. The HCI socket will be marked as
trusted when the privileged task occasionally makes an ioctl call.

This problem can be solved by using sk_capable() to check capability, which
ensures that not only the current task but also the socket opener has the
specified capability, thus reducing the risk of privilege escalation
through the previously identified vulnerability.

Cc: stable@vger.kernel.org
Fixes: f81f5b2d ("Bluetooth: Send control open and close messages for HCI raw sockets")
Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

conn->chan_lock isn't acquired before l2cap_get_chan_by_scid,
if l2cap_get_chan_by_scid returns NULL, then 'bad unlock balance'
is triggered.

Reported-by: syzbot+9519d6b5b79cf7787cf3@syzkaller.appspotmail.com
Link: https://lore.kernel.org/all/000000000000894f5f05f95e9f4d@google.com/Signed-off-by: Min Li <lm0963hack@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Previously, channel open messages were always sent to monitors on the first
ioctl() call for unbound HCI sockets, even if the command and arguments
were completely invalid. This can leave an exploitable hole with the abuse
of invalid ioctl calls.

This commit hardens the ioctl processing logic by first checking if the
command is valid, and immediately returning with an ENOIOCTLCMD error code
if it is not. This ensures that ioctl calls with invalid commands are free
of side effects, and increases the difficulty of further exploitation by
forcing exploitation to find a way to pass a valid command first.
Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn>
Co-developed-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This reverts commit 1e9ac114.

This patch introduces a possible null-ptr-def problem. Revert it. And the
fixed bug by this patch have resolved by commit 73f7b171 ("Bluetooth:
btsdio: fix use after free bug in btsdio_remove due to race condition").

Fixes: 1e9ac114 ("Bluetooth: btsdio: fix use after free bug in btsdio_remove due to unfinished work")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The ATS2851 based controller advertises support for command "LE Set Random
Private Address Timeout" but does not actually implement it, impeding the
controller initialization.

Add the quirk HCI_QUIRK_BROKEN_SET_RPA_TIMEOUT to unblock the controller
initialization.

< HCI Command: LE Set Resolvable Private... (0x08|0x002e) plen 2
        Timeout: 900 seconds
> HCI Event: Command Status (0x0f) plen 4
      LE Set Resolvable Private Address Timeout (0x08|0x002e) ncmd 1
        Status: Unknown HCI Command (0x01)
Co-developed-by: imoc <wzj9912@gmail.com>
Signed-off-by: imoc <wzj9912@gmail.com>
Signed-off-by: Raul Cheleguini <raul.cheleguini@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

When submitting HCI_OP_LE_CREATE_CIS the code shall wait for
HCI_EVT_LE_CIS_ESTABLISHED thus enforcing the serialization of
HCI_OP_LE_CREATE_CIS as the Core spec does not allow to send them in
parallel:

  BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 4, Part E page 2566:

  If the Host issues this command before all the HCI_LE_CIS_Established
  events from the previous use of the command have been generated, the
  Controller shall return the error code Command Disallowed (0x0C).
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This fixes only matching CIS by address which prevents creating new hcon
if upper layer is requesting a specific CIS ID.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Since it is required for some configurations to have multiple CIS with
the same peer which is now covered by iso-tester in the following test
cases:

    ISO AC 6(i) - Success
    ISO AC 7(i) - Success
    ISO AC 8(i) - Success
    ISO AC 9(i) - Success
    ISO AC 11(i) - Success
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

There are a number of bugs here:

1) If "count" is less than sizeof(dump_data.data) then it copies
   uninitialized data.
2) If simple_write_to_buffer() returns -EFAULT then we run into a
   problem "ret < count" comparison.  "count" is an unsigned long so the
   comparison is type promoted to unsigned long and the negative returns
   become high positive values.  That also results in copying
   uninitialized data.
3) If "*ppos" is non-zero then the first part of the dump_data
   buffer is uninitialized.  Using copy_from_user() instead of
   simple_write_to_buffer() is more appropriate here.

Fixes: d5d5df6da0aa ("Bluetooth: Add vhci devcoredump support")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The driver can be compile tested with !CONFIG_OF making certain data
unused.
Signed-off-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Remove extra line setting the broadcast code parameter of the
hci_cp_le_create_big struct to 0. The broadcast code is copied
from the QoS struct.
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Fixed a wrong indentation before "return".This line uses a 7 space
indent instead of a tab.
Signed-off-by: Lanzhe Li <u202212060@hust.edu.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

We can never assume the uart will deliver a complete packet to the BT
layer at once, the expected packet may be divided into several parts by
uart as uart doesn't know the received packet size, the received data
count may mismatch with the expected packet size, so here
is_valid_bootloader_signature() check may always return false.

Even we remove the count check in is_valid_bootloader_signature(), then
the first part of the data which includes the packet type can pass the
is_valid_bootloader_signature() check, but the remaining parts don't
have the packet type data still cannot pass the check, here return
directly will cause the data loss.

So need to remove the received bootloader signature check here, the
h4_recv_buf() can help us combine the different data received into one
packet. If any out-of-sync or incomplete bootloader signature is received,
it is safe to ignore and discard it, and process the next bootloader
signature.
Co-developed-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This sets the default power save mode setting to disabled.
With this setting, this driver will behave like a normal h4 driver.
If user needs to use the power save feature, it can be enabled
using the following vendor command:
hcitool cmd 3f 23 02 00 00 (HCI_NXP_AUTO_SLEEP_MODE)
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This adds a call to ps_wakeup() before closing the serdev device, to
de-assert UART break.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This adds support to download helper FW file for the legacy NXP chipset
88w8997 for the btnxpuart driver. This helper FW file is necessary to
set the bootloader baudrate to 3000000 after which the actual BT FW file
can be downloaded. This change helps bring the FW download time from
around 10 sec to less than 2 sec for 88w8997 chip. For newer chipsets,
both V1 and V3 bootloader, driver sends the cmd5 and cmd7 to the chip
bootloader, and does not need a helper FW file.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>