- 31 Jan, 2013 24 commits
-
-
Amir Vadai authored
Under heavy CPU load, changing, ring size/mtu/etc. could result in transmit timeout, since stop-start port might take more than 10 seconds. Calling netif_detach_device to prevent tx queue transmit timeout. netif_detach_device() is not called under ndo_stop, because netif_carrier_off will prevent the timeout, and device should not be marked as not present, or else user won't be able to start it later on. CC: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Matan Barak authored
Mac reassignments should only be done when not supported by the firmware. To accomplish that, checking firmware capability bit to know whether we should reassign macs in the driver. Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Hadar Hen Zion authored
The Firmware dynamically changes flow steering hash configuration from covering L2 only to "full" L2/L3/L4 mode needed. The dynamic change allows the driver to set hard coded hash configuration which is changed by the firmware from L2 to L2/L3/L4 when attaching the first L3/L4 flow steering rule and back to L2 when there are no more such rules. Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Hadar Hen Zion authored
As part of the driver unload flow, all steering rules must be deleted, make sure to remove the rules that were set through ethtool. Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Hadar Hen Zion authored
Attaching steering rules while the interface is down is an invalid operation, block it. Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Hadar Hen Zion authored
The vlan mask field should be validated and assigned according to the field size which is 12 bits. Also replace the numeric 0xfff mask with existing kernel macro. Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Hadar Hen Zion authored
When attaching flow steering rules via Ethtool accept only valid vlans IDs e.g in the range: [0,4095]. Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Hadar Hen Zion authored
Destination mac is a mandatory specification for ip/udp steering rules. When attaching multicast steering rules via ethtool the unicast mac of the interface was added to the rule specification instead of the multicast mac. The following commit sets the corresponding multicast mac for the rule multicast ip. Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Hadar Hen Zion authored
The allow_loopback flag was wrongly set using arithmetic bit operation, change the code to use logical bit operation. Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Hadar Hen Zion authored
Some of the fields for struct mlx4_net_trans_rule_hw_ctrl were packed into u32 and accessed through bit field operations. Expose and access them directly as u8. Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yan Burman authored
Implement ethtool get_drvinfo. Signed-off-by: Yan Burman <yanb@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
YOSHIFUJI Hideaki / 吉藤英明 authored
Since all users are write-lock, it does not make sense to use rwlock here. Use simple spinlock. Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
YOSHIFUJI Hideaki / 吉藤英明 authored
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
YOSHIFUJI Hideaki / 吉藤英明 authored
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
YOSHIFUJI Hideaki / 吉藤英明 authored
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
Supporting access to skb->pkt_type is a bit tricky if we want to have a generic code, allowing pkt_type to be moved in struct sk_buff pkt_type is a bit field, so compiler cannot really help us to find its offset. Let's use a helper for this : It will throw a one time message if pkt_type no longer starts at a byte boundary or is no longer a 3bit field. Reported-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jitendra Kalsaria authored
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Stephen Hemminger authored
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Manish chopra authored
Signed-off-by: Manish chopra <manish.chopra@qlogic.com> Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Shahed Shaikh authored
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Manish chopra authored
o ipv4 address was not getting programmed properly because of improper byte order conversion Signed-off-by: Manish chopra <manish.chopra@qlogic.com> Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Manish chopra authored
Signed-off-by: Manish chopra <manish.chopra@qlogic.com> Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Manish chopra authored
Signed-off-by: Manish chopra <manish.chopra@qlogic.com> Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Shahed Shaikh authored
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 30 Jan, 2013 7 commits
-
-
Jiri Pirko authored
Makes more sense to have randomly generated address by default than to have all zeroes. It also allows user to for example put the bond into bridge without need to have any slaves in it. Also note that this changes only behaviour of bonds with no slaves. Once the first slave device is enslaved, its address will be used (no change here). Also, fix dev_assign_type values on the way. Reported-by: Pavel Šimerda <psimerda@redhat.com> Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Michał Mirosław authored
Instead of jumping aroung bugs that are easily fixed just don't let them in: affected drivers should be either fixed or have NETIF_F_HW_VLAN_FILTER removed from advertised features. Quick grep in drivers/net shows two drivers that have NETIF_F_HW_VLAN_FILTER but not ndo_vlan_rx_add/kill_vid(), but those are false-positives (features are commented out). OTOH two drivers have ndo_vlan_rx_add/kill_vid() implemented but don't advertise NETIF_F_HW_VLAN_FILTER. Those are: +ethernet/cisco/enic/enic_main.c +ethernet/qlogic/qlcnic/qlcnic_main.c Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
-
YOSHIFUJI Hideaki / 吉藤英明 authored
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
YOSHIFUJI Hideaki / 吉藤英明 authored
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
YOSHIFUJI Hideaki / 吉藤英明 authored
All users of xfrm_addr_cmp() use its result as boolean. Introduce xfrm_addr_equal() (which is equal to !xfrm_addr_cmp()) and convert all users. Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
YOSHIFUJI Hideaki / 吉藤英明 authored
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
YOSHIFUJI Hideaki / 吉藤英明 authored
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 29 Jan, 2013 9 commits
-
-
git://git.open-mesh.org/linux-mergeDavid S. Miller authored
Included changes: - fix recently introduced output behaviour Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller authored
Bring in the 'net' tree so that we can get some ipv4/ipv6 bug fixes that some net-next work will build upon. Signed-off-by: David S. Miller <davem@davemloft.net>
-
Hannes Frederic Sowa authored
This patch adds anti-spoofing checks in sit.c as specified in RFC3964 section 5.2 for 6to4 and RFC5969 section 12 for 6rd. I left out the checks which could easily be implemented with netfilter. Specifically this patch adds following logic (based loosely on the pseudocode in RFC3964 section 5.2): if prefix (inner_src_v6) == rd6_prefix (2002::/16 is the default) and outer_src_v4 != embedded_ipv4 (inner_src_v6) drop if prefix (inner_dst_v6) == rd6_prefix (or 2002::/16 is the default) and outer_dst_v4 != embedded_ipv4 (inner_dst_v6) drop accept To accomplish the specified security checks proposed by above RFCs, it is still necessary to employ uRPF filters with netfilter. These new checks only kick in if the employed addresses are within the 2002::/16 or another range specified by the 6rd-prefix (which defaults to 2002::/16). Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Cc: David Miller <davem@davemloft.net> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Claudiu Manoil authored
* remove unused members(!): imask, ievent * move space consuming interrupt name strings (int_name_* members) to external structures, unessential for the driver's hot path * keep high priority hot path data within the first 2 cache lines This reduces struct gfar_priv_grp from 6 to 3 cache lines. (Also fixed checkpatch warnings for the old code, in the process.) Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Claudiu Manoil authored
Factor out redundant code (improve readability, source code size). Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Claudiu Manoil authored
Resize and regroup structure members to eliminate memory holes and to pack the structure into 2 cache lines (from 3). tx_ring_size was resized from 4 to 2 bytes and few members were re-grouped in order to eliminate byte holes and achieve compactness. Where possible, few members were grouped according to their usage and access order (i.e. start_xmit vs. clean_tx_ring members), less important members were pushed at the end. Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric W. Biederman authored
When attempting to build linux-next with user namespaces enabled I ran into this fun build error. CC net/ipv6/inet6_connection_sock.o .../net/ipv6/inet6_connection_sock.c: In function ‘inet6_csk_bind_conflict’: .../net/ipv6/inet6_connection_sock.c:37:12: error: incompatible types when initializing type ‘int’ using type ‘kuid_t’ .../net/ipv6/inet6_connection_sock.c:54:30: error: incompatible type for argument 1 of ‘uid_eq’ .../include/linux/uidgid.h:48:20: note: expected ‘kuid_t’ but argument is of type ‘int’ make[3]: *** [net/ipv6/inet6_connection_sock.o] Error 1 make[2]: *** [net/ipv6] Error 2 make[2]: *** Waiting for unfinished jobs.... Using kuid_t instead of int to hold the uid fixes this. Cc: Tom Herbert <therbert@google.com> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Cong Wang authored
v3: make pktgen_threads list per-namespace v2: remove a useless check This patch add net namespace to pktgen, so that we can use pktgen in different namespaces. Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Cong Wang <amwang@redhat.com> Acked-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Frank Li authored
Add napi support Before this patch iperf -s -i 1 ------------------------------------------------------------ Server listening on TCP port 5001 TCP window size: 85.3 KByte (default) ------------------------------------------------------------ [ 4] local 10.192.242.153 port 5001 connected with 10.192.242.138 port 50004 [ ID] Interval Transfer Bandwidth [ 4] 0.0- 1.0 sec 41.2 MBytes 345 Mbits/sec [ 4] 1.0- 2.0 sec 43.7 MBytes 367 Mbits/sec [ 4] 2.0- 3.0 sec 42.8 MBytes 359 Mbits/sec [ 4] 3.0- 4.0 sec 43.7 MBytes 367 Mbits/sec [ 4] 4.0- 5.0 sec 42.7 MBytes 359 Mbits/sec [ 4] 5.0- 6.0 sec 43.8 MBytes 367 Mbits/sec [ 4] 6.0- 7.0 sec 43.0 MBytes 361 Mbits/sec After this patch [ 4] 2.0- 3.0 sec 51.6 MBytes 433 Mbits/sec [ 4] 3.0- 4.0 sec 51.8 MBytes 435 Mbits/sec [ 4] 4.0- 5.0 sec 52.2 MBytes 438 Mbits/sec [ 4] 5.0- 6.0 sec 52.1 MBytes 437 Mbits/sec [ 4] 6.0- 7.0 sec 52.1 MBytes 437 Mbits/sec [ 4] 7.0- 8.0 sec 52.3 MBytes 439 Mbits/sec Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-