- 17 Sep, 2019 40 commits
-
-
Miaoqing Pan authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit 011d4111 ] Observed PCIE device wake up failed after ~120 iterations of soft-reboot test. The error message is "ath10k_pci 0000:01:00.0: failed to wake up device : -110" The call trace as below: ath10k_pci_probe -> ath10k_pci_force_wake -> ath10k_pci_wake_wait -> ath10k_pci_is_awake Once trigger the device to wake up, we will continuously check the RTC state until it returns RTC_STATE_V_ON or timeout. But for QCA99x0 chips, we use wrong value for RTC_STATE_V_ON. Occasionally, we get 0x7 on the fist read, we thought as a failure case, but actually is the right value, also verified with the spec. So fix the issue by changing RTC_STATE_V_ON from 0x5 to 0x7, passed ~2000 iterations. Tested HW: QCA9984 Signed-off-by:
Miaoqing Pan <miaoqing@codeaurora.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
Sasha Levin <sashal@kernel.org> Signed-off-by:
Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by:
Kleber Sacilotto de Souza <kleber.souza@canonical.com>
-
Lorenzo Bianconi authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit 23377c20 ] When the device is disconnected while passing traffic it is possible to receive out of order urbs causing a memory leak since the skb linked to the current tx urb is not removed. Fix the issue deallocating the skb cleaning up the tx ring. Moreover this patch fixes the following kernel warning [ 57.480771] usb 1-1: USB disconnect, device number 2 [ 57.483451] ------------[ cut here ]------------ [ 57.483462] TX urb mismatch [ 57.483481] WARNING: CPU: 1 PID: 32 at drivers/net/wireless/mediatek/mt7601u/dma.c:245 mt7601u_complete_tx+0x165/00 [ 57.483483] Modules linked in: [ 57.483496] CPU: 1 PID: 32 Comm: kworker/1:1 Not tainted 5.2.0-rc1+ #72 [ 57.483498] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.12.0-2.fc30 04/01/2014 [ 57.483502] Workqueue: usb_hub_wq hub_event [ 57.483507] RIP: 0010:mt7601u_complete_tx+0x165/0x1e0 [ 57.483510] Code: 8b b5 10 04 00 00 8b 8d 14 04 00 00 eb 8b 80 3d b1 cb e1 00 00 75 9e 48 c7 c7 a4 ea 05 82 c6 05 f [ 57.483513] RSP: 0000:ffffc900000a0d28 EFLAGS: 00010092 [ 57.483516] RAX: 000000000000000f RBX: ffff88802c0a62c0 RCX: ffffc900000a0c2c [ 57.483518] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffff810a8371 [ 57.483520] RBP: ffff88803ced6858 R08: 0000000000000000 R09: 0000000000000001 [ 57.483540] R10: 0000000000000002 R11: 0000000000000000 R12: 0000000000000046 [ 57.483542] R13: ffff88802c0a6c88 R14: ffff88803baab540 R15: ffff88803a0cc078 [ 57.483548] FS: 0000000000000000(0000) GS:ffff88803eb00000(0000) knlGS:0000000000000000 [ 57.483550] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 57.483552] CR2: 000055e7f6780100 CR3: 0000000028c86000 CR4: 00000000000006a0 [ 57.483554] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 57.483556] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 57.483559] Call Trace: [ 57.483561] <IRQ> [ 57.483565] __usb_hcd_giveback_urb+0x77/0xe0 [ 57.483570] xhci_giveback_urb_in_irq.isra.0+0x8b/0x140 [ 57.483574] handle_cmd_completion+0xf5b/0x12c0 [ 57.483577] xhci_irq+0x1f6/0x1810 [ 57.483581] ? lockdep_hardirqs_on+0x9e/0x180 [ 57.483584] ? _raw_spin_unlock_irq+0x24/0x30 [ 57.483588] __handle_irq_event_percpu+0x3a/0x260 [ 57.483592] handle_irq_event_percpu+0x1c/0x60 [ 57.483595] handle_irq_event+0x2f/0x4c [ 57.483599] handle_edge_irq+0x7e/0x1a0 [ 57.483603] handle_irq+0x17/0x20 [ 57.483607] do_IRQ+0x54/0x110 [ 57.483610] common_interrupt+0xf/0xf [ 57.483612] </IRQ> Acked-by:
Jakub Kicinski <kubakici@wp.pl> Signed-off-by:
Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by:
-
Masahiro Yamada authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit bc53d3d7 ] Without 'set -e', shell scripts continue running even after any error occurs. The missed 'set -e' is a typical bug in shell scripting. For example, when a disk space shortage occurs while this script is running, it actually ends up with generating a truncated capflags.c. Yet, mkcapflags.sh continues running and exits with 0. So, the build system assumes it has succeeded. It will not be re-generated in the next invocation of Make since its timestamp is newer than that of any of the source files. Add 'set -e' so that any error in this script is caught and propagated to the build system. Since 9c2af1c7 ("kbuild: add .DELETE_ON_ERROR special target"), make automatically deletes the target on any failure. So, the broken capflags.c will be deleted automatically. Signed-off-by:
Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Borislav Petkov <bp@alien8.de> Link: https://lkml.kernel.org/r/20190625072622.17679-1-yamada.masahiro@socionext.comSigned-off-by:
-
Lorenzo Bianconi authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit 4079e8cc ] Do not schedule rx_tasklet when the usb dongle is disconnected. Moreover do not grub rx_lock in mt7601u_kill_rx since usb_poison_urb can run concurrently with urb completion and we can unlink urbs from rx ring in any order. This patch fixes the common kernel warning reported when the device is removed. [ 24.921354] usb 3-14: USB disconnect, device number 7 [ 24.921593] ------------[ cut here ]------------ [ 24.921594] RX urb mismatch [ 24.921675] WARNING: CPU: 4 PID: 163 at drivers/net/wireless/mediatek/mt7601u/dma.c:200 mt7601u_complete_rx+0xcb/0xd0 [mt7601u] [ 24.921769] CPU: 4 PID: 163 Comm: kworker/4:2 Tainted: G OE 4.19.31-041931-generic #201903231635 [ 24.921770] Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./Z97 Extreme4, BIOS P1.30 05/23/2014 [ 24.921782] Workqueue: usb_hub_wq hub_event [ 24.921797] RIP: 0010:mt7601u_complete_rx+0xcb/0xd0 [mt7601u] [ 24.921800] RSP: 0018:ffff9bd9cfd03d08 EFLAGS: 00010086 [ 24.921802] RAX: 0000000000000000 RBX: ffff9bd9bf043540 RCX: 0000000000000006 [ 24.921803] RDX: 0000000000000007 RSI: 0000000000000096 RDI: ffff9bd9cfd16420 [ 24.921804] RBP: ffff9bd9cfd03d28 R08: 0000000000000002 R09: 00000000000003a8 [ 24.921805] R10: 0000002f485fca34 R11: 0000000000000000 R12: ffff9bd9bf043c1c [ 24.921806] R13: ffff9bd9c62fa3c0 R14: 0000000000000082 R15: 0000000000000000 [ 24.921807] FS: 0000000000000000(0000) GS:ffff9bd9cfd00000(0000) knlGS:0000000000000000 [ 24.921808] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 24.921808] CR2: 00007fb2648b0000 CR3: 0000000142c0a004 CR4: 00000000001606e0 [ 24.921809] Call Trace: [ 24.921812] <IRQ> [ 24.921819] __usb_hcd_giveback_urb+0x8b/0x140 [ 24.921821] usb_hcd_giveback_urb+0xca/0xe0 [ 24.921828] xhci_giveback_urb_in_irq.isra.42+0x82/0xf0 [ 24.921834] handle_cmd_completion+0xe02/0x10d0 [ 24.921837] xhci_irq+0x274/0x4a0 [ 24.921838] xhci_msi_irq+0x11/0x20 [ 24.921851] __handle_irq_event_percpu+0x44/0x190 [ 24.921856] handle_irq_event_percpu+0x32/0x80 [ 24.921861] handle_irq_event+0x3b/0x5a [ 24.921867] handle_edge_irq+0x80/0x190 [ 24.921874] handle_irq+0x20/0x30 [ 24.921889] do_IRQ+0x4e/0xe0 [ 24.921891] common_interrupt+0xf/0xf [ 24.921892] </IRQ> [ 24.921900] RIP: 0010:usb_hcd_flush_endpoint+0x78/0x180 [ 24.921354] usb 3-14: USB disconnect, device number 7 Signed-off-by:
-
Philipp Zabel authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit b3b7d968 ] If no more frames are decoded in bitstream end mode, and a previously decoded frame has been returned, the firmware still increments the frame number. To avoid a sequence number mismatch after decoder restart, increment the sequence_offset correction parameter. Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by:
-
Philipp Zabel authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit 56d159a4 ] Sequence number handling assumed that the BIT processor frame number starts counting at 1, but this is not true for the MPEG-2 decoder, which starts at 0. Fix the sequence counter offset detection to handle this. Signed-off-by:
-
Ard Biesheuvel authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit 2af22f3e ] Some Qualcomm Snapdragon based laptops built to run Microsoft Windows are clearly ACPI 5.1 based, given that that is the first ACPI revision that supports ARM, and introduced the FADT 'arm_boot_flags' field, which has a non-zero field on those systems. So in these cases, infer from the ARM boot flags that the FADT must be 5.1 or later, and treat it as 5.1. Acked-by:
Sudeep Holla <sudeep.holla@arm.com> Tested-by:
Lee Jones <lee.jones@linaro.org> Reviewed-by:
Graeme Gregory <graeme.gregory@linaro.org> Acked-by:
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by:
Hanjun Guo <guohanjun@huawei.com> Signed-off-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
Nathan Huckleberry authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit a9314773 ] With CONFIG_PROC_FS=n the following warning is emitted: kernel/time/timer_list.c:361:36: warning: unused variable 'timer_list_sops' [-Wunused-const-variable] static const struct seq_operations timer_list_sops = { Add #ifdef guard around procfs specific code. Signed-off-by:
Nathan Huckleberry <nhuck@google.com> Signed-off-by:
Nick Desaulniers <ndesaulniers@google.com> Cc: john.stultz@linaro.org Cc: sboyd@kernel.org Cc: clang-built-linux@googlegroups.com Link: https://github.com/ClangBuiltLinux/linux/issues/534 Link: https://lkml.kernel.org/r/20190614181604.112297-1-nhuck@google.comSigned-off-by:
-
Miroslav Lichvar authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit d897a4ab ] Don't allow the TAI-UTC offset of the system clock to be set by adjtimex() to a value larger than 100000 seconds. This prevents an overflow in the conversion to int, prevents the CLOCK_TAI clock from getting too far ahead of the CLOCK_REALTIME clock, and it is still large enough to allow leap seconds to be inserted at the maximum rate currently supported by the kernel (once per day) for the next ~270 years, however unlikely it is that someone can survive a catastrophic event which slowed down the rotation of the Earth so much. Reported-by:
Weikang shi <swkhack@gmail.com> Signed-off-by:
Miroslav Lichvar <mlichvar@redhat.com> Signed-off-by:
-
Anders Roxell authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit b2ce5617 ] When building with CONFIG_VIDEO_ADV7511 and CONFIG_DRM_I2C_ADV7511 enabled as loadable modules, we see the following warning: drivers/gpu/drm/bridge/adv7511/adv7511.ko drivers/media/i2c/adv7511.ko Rework so that the file is named adv7511-v4l2.c. Signed-off-by:
Anders Roxell <anders.roxell@linaro.org> Signed-off-by:
-
Pan Bian authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit 585fb3d9 ] In edac_create_csrow_object(), the reference to the object is not released when adding the device to the device hierarchy fails (device_add()). This may result in a memory leak. Signed-off-by:
Pan Bian <bianpan2016@163.com> Signed-off-by:
Borislav Petkov <bp@suse.de> Reviewed-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: James Morse <james.morse@arm.com> Cc: Mauro Carvalho Chehab <mchehab@kernel.org> Cc: linux-edac <linux-edac@vger.kernel.org> Link: https://lkml.kernel.org/r/1555554438-103953-1-git-send-email-bianpan2016@163.comSigned-off-by:
-
Jason Wang authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit 098eadce ] Vhost_net was known to suffer from HOL[1] issues which is not easy to fix. Several downstream disable the feature by default. What's more, the datapath was split and datacopy path got the support of batching and XDP support recently which makes it faster than zerocopy part for small packets transmission. It looks to me that disable zerocopy by default is more appropriate. It cold be enabled by default again in the future if we fix the above issues. [1] https://patchwork.kernel.org/patch/3787671/Signed-off-by:
Jason Wang <jasowang@redhat.com> Acked-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Arnaldo Carvalho de Melo authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit fdbdd7e8 ] In which case it simply returns "unknown", like when it can't figure out the evsel->name value. This makes this code more robust and fixes a problem in 'perf trace' where a NULL evsel was being passed to a routine that only used the evsel for printing its name when a invalid syscall id was passed. Reported-by:
Leo Yan <leo.yan@linaro.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Link: https://lkml.kernel.org/n/tip-f30ztaasku3z935cn3ak3h53@git.kernel.orgSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Nicolas Dichtel authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit b8d6d007 ] After commit b38ff407, the following command does not work anymore: $ ip xfrm state add src 10.125.0.2 dst 10.125.0.1 proto esp spi 34 reqid 1 \ mode tunnel enc 'cbc(aes)' 0xb0abdba8b782ad9d364ec81e3a7d82a1 auth-trunc \ 'hmac(sha1)' 0xe26609ebd00acb6a4d51fca13e49ea78a72c73e6 96 flag align4 In fact, the selector is not mandatory, allow the user to provide an empty selector. Fixes: b38ff407 ("xfrm: Fix xfrm sel prefix length validation") CC: Anirudh Gupta <anirudh.gupta@sophos.com> Signed-off-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by:
-
Waiman Long authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit 6da9f775 ] When debugging options are turned on, the rcu_read_lock() function might not be inlined. This results in lockdep's print_lock() function printing "rcu_read_lock+0x0/0x70" instead of rcu_read_lock()'s caller. For example: [ 10.579995] ============================= [ 10.584033] WARNING: suspicious RCU usage [ 10.588074] 4.18.0.memcg_v2+ #1 Not tainted [ 10.593162] ----------------------------- [ 10.597203] include/linux/rcupdate.h:281 Illegal context switch in RCU read-side critical section! [ 10.606220] [ 10.606220] other info that might help us debug this: [ 10.606220] [ 10.614280] [ 10.614280] rcu_scheduler_active = 2, debug_locks = 1 [ 10.620853] 3 locks held by systemd/1: [ 10.624632] #0: (____ptrval____) (&type->i_mutex_dir_key#5){.+.+}, at: lookup_slow+0x42/0x70 [ 10.633232] #1: (____ptrval____) (rcu_read_lock){....}, at: rcu_read_lock+0x0/0x70 [ 10.640954] #2: (____ptrval____) (rcu_read_lock){....}, at: rcu_read_lock+0x0/0x70 These "rcu_read_lock+0x0/0x70" strings are not providing any useful information. This commit therefore forces inlining of the rcu_read_lock() function so that rcu_read_lock()'s caller is instead shown. Signed-off-by:
Waiman Long <longman@redhat.com> Signed-off-by:
Paul E. McKenney <paulmck@linux.ibm.com> Signed-off-by:
-
Valdis Klētnieks authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit aee450cb ] Compiling kernel/bpf/core.c with W=1 causes a flood of warnings: kernel/bpf/core.c:1198:65: warning: initialized field overwritten [-Woverride-init] 1198 | #define BPF_INSN_3_TBL(x, y, z) [BPF_##x | BPF_##y | BPF_##z] = true | ^~~~ kernel/bpf/core.c:1087:2: note: in expansion of macro 'BPF_INSN_3_TBL' 1087 | INSN_3(ALU, ADD, X), \ | ^~~~~~ kernel/bpf/core.c:1202:3: note: in expansion of macro 'BPF_INSN_MAP' 1202 | BPF_INSN_MAP(BPF_INSN_2_TBL, BPF_INSN_3_TBL), | ^~~~~~~~~~~~ kernel/bpf/core.c:1198:65: note: (near initialization for 'public_insntable[12]') 1198 | #define BPF_INSN_3_TBL(x, y, z) [BPF_##x | BPF_##y | BPF_##z] = true | ^~~~ kernel/bpf/core.c:1087:2: note: in expansion of macro 'BPF_INSN_3_TBL' 1087 | INSN_3(ALU, ADD, X), \ | ^~~~~~ kernel/bpf/core.c:1202:3: note: in expansion of macro 'BPF_INSN_MAP' 1202 | BPF_INSN_MAP(BPF_INSN_2_TBL, BPF_INSN_3_TBL), | ^~~~~~~~~~~~ 98 copies of the above. The attached patch silences the warnings, because we *know* we're overwriting the default initializer. That leaves bpf/core.c with only 6 other warnings, which become more visible in comparison. Signed-off-by:
Valdis Kletnieks <valdis.kletnieks@vt.edu> Acked-by:
Andrii Nakryiko <andriin@fb.com> Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
-
Srinivas Kandagatla authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit db057679 ] On buses like SlimBus and SoundWire which does not support gather_writes yet in regmap, A bulk write on paged register would be silently ignored after programming page. This is because local variable 'ret' value in regmap_raw_write_impl() gets reset to 0 once page register is written successfully and the code below checks for 'ret' value to be -ENOTSUPP before linearising the write buffer to send to bus->write(). Fix this by resetting the 'ret' value to -ENOTSUPP in cases where gather_writes() is not supported or single register write is not possible. Signed-off-by:
Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Russell King authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit c859e0d4 ] Documentation states: NOTE: There must be a correlation between the wake-up enable and interrupt-enable registers. If a GPIO pin has a wake-up configured on it, it must also have the corresponding interrupt enabled (on one of the two interrupt lines). Ensure that this condition is always satisfied by enabling the detection events after enabling the interrupt, and disabling the detection before disabling the interrupt. This ensures interrupt/wakeup events can not happen until both the wakeup and interrupt enables correlate. If we do any clearing, clear between the interrupt enable/disable and trigger setting. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
Grygorii Strashko <grygorii.strashko@ti.com> Tested-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Russell King authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit 64ea3e90 ] Commit 384ebe1c ("gpio/omap: Add DT support to GPIO driver") added the register definition tables to the gpio-omap driver. Subsequently to that commit, commit 4e962e89 ("gpio/omap: remove cpu_is_omapxxxx() checks from *_runtime_resume()") added definitions for irqstatus_raw* registers to the legacy OMAP4 definitions, but missed the DT definitions. This causes an unintentional change of behaviour for the 1.101 errata workaround on OMAP4 platforms. Fix this oversight. Fixes: 4e962e89 ("gpio/omap: remove cpu_is_omapxxxx() checks from *_runtime_resume()") Signed-off-by:
-
Thomas Richter authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit 53fe307d ] Command # perf test -Fv 6 fails with error running test 100 'kvm-s390:kvm_s390_create_vm' failed to parse event 'kvm-s390:kvm_s390_create_vm', err -1, str 'unknown tracepoint' event syntax error: 'kvm-s390:kvm_s390_create_vm' \___ unknown tracepoint when the kvm module is not loaded or not built in. Fix this by adding a valid function which tests if the module is loaded. Loaded modules (or builtin KVM support) have a directory named /sys/kernel/debug/tracing/events/kvm-s390 for this tracepoint. Check for existence of this directory. Signed-off-by:
Thomas Richter <tmricht@linux.ibm.com> Reviewed-by:
Christian Borntraeger <borntraeger@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Link: http://lkml.kernel.org/r/20190604053504.43073-1-tmricht@linux.ibm.comSigned-off-by:
-
Julian Wiedmann authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit 04310324 ] When a CQ-enabled device uses QEBSM for SBAL state inspection, get_buf_states() can return the PENDING state for an Output Queue. get_outbound_buffer_frontier() isn't prepared for this, and any PENDING buffer will permanently stall all further completion processing on this Queue. This isn't a concern for non-QEBSM devices, as get_buf_states() for such devices will manually turn PENDING buffers into EMPTY ones. Fixes: 104ea556 ("qdio: support asynchronous delivery of storage blocks") Signed-off-by:
Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by:
-
Robert Hancock authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit 7de44285 ] It is possible that the interrupt handler fires and frees up space in the TX ring in between checking for sufficient TX ring space and stopping the TX queue in axienet_start_xmit. If this happens, the queue wake from the interrupt handler will occur before the queue is stopped, causing a lost wakeup and the adapter's transmit hanging. To avoid this, after stopping the queue, check again whether there is sufficient space in the TX ring. If so, wake up the queue again. Signed-off-by:
Robert Hancock <hancock@sedsystems.ca> Signed-off-by:
-
Fabio Estevam authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit a19a0582 ] When a valid MAC address is not found the current messages are shown: fec 2188000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00 fec 2188000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: aa:9f:25:eb:7e:aa Since the network device has not been registered at this point, it is better to use dev_err()/dev_info() instead, which will provide cleaner log messages like these: fec 2188000.ethernet: Invalid MAC address: 00:00:00:00:00:00 fec 2188000.ethernet: Using random MAC address: aa:9f:25:eb:7e:aa Tested on a imx6dl-pico-pi board. Signed-off-by:
Fabio Estevam <festevam@gmail.com> Signed-off-by:
-
Abhishek Goel authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit 04507c0a ] To set frequency on specific cpus using cpupower, following syntax can be used : cpupower -c #i frequency-set -f #f -r While setting frequency using cpupower frequency-set command, if we use '-r' option, it is expected to set frequency for all cpus related to cpu #i. But it is observed to be missing the last cpu in related cpu list. This patch fixes the problem. Signed-off-by:
Abhishek Goel <huntbag@linux.vnet.ibm.com> Reviewed-by:
Thomas Renninger <trenn@suse.de> Signed-off-by:
Shuah Khan <skhan@linuxfoundation.org> Signed-off-by:
-
Kefeng Wang authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit 69fbb3f4 ] X-Originating-IP: [10.175.113.25] X-CFilter-Loop: Reflected The fm_v4l2_init_video_device() forget to unregister v4l2/video device in the error path, it could lead to UAF issue, eg, BUG: KASAN: use-after-free in atomic64_read include/asm-generic/atomic-instrumented.h:836 [inline] BUG: KASAN: use-after-free in atomic_long_read include/asm-generic/atomic-long.h:28 [inline] BUG: KASAN: use-after-free in __mutex_unlock_slowpath+0x92/0x690 kernel/locking/mutex.c:1206 Read of size 8 at addr ffff8881e84a7c70 by task v4l_id/3659 CPU: 1 PID: 3659 Comm: v4l_id Not tainted 5.1.0 #8 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xa9/0x10e lib/dump_stack.c:113 print_address_description+0x65/0x270 mm/kasan/report.c:187 kasan_report+0x149/0x18d mm/kasan/report.c:317 atomic64_read include/asm-generic/atomic-instrumented.h:836 [inline] atomic_long_read include/asm-generic/atomic-long.h:28 [inline] __mutex_unlock_slowpath+0x92/0x690 kernel/locking/mutex.c:1206 fm_v4l2_fops_open+0xac/0x120 [fm_drv] v4l2_open+0x191/0x390 [videodev] chrdev_open+0x20d/0x570 fs/char_dev.c:417 do_dentry_open+0x700/0xf30 fs/open.c:777 do_last fs/namei.c:3416 [inline] path_openat+0x7c4/0x2a90 fs/namei.c:3532 do_filp_open+0x1a5/0x2b0 fs/namei.c:3563 do_sys_open+0x302/0x490 fs/open.c:1069 do_syscall_64+0x9f/0x450 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x7f8180c17c8e ... Allocated by task 3642: set_track mm/kasan/common.c:87 [inline] __kasan_kmalloc.constprop.3+0xa0/0xd0 mm/kasan/common.c:497 fm_drv_init+0x13/0x1000 [fm_drv] do_one_initcall+0xbc/0x47d init/main.c:901 do_init_module+0x1b5/0x547 kernel/module.c:3456 load_module+0x6405/0x8c10 kernel/module.c:3804 __do_sys_finit_module+0x162/0x190 kernel/module.c:3898 do_syscall_64+0x9f/0x450 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe Freed by task 3642: set_track mm/kasan/common.c:87 [inline] __kasan_slab_free+0x130/0x180 mm/kasan/common.c:459 slab_free_hook mm/slub.c:1429 [inline] slab_free_freelist_hook mm/slub.c:1456 [inline] slab_free mm/slub.c:3003 [inline] kfree+0xe1/0x270 mm/slub.c:3958 fm_drv_init+0x1e6/0x1000 [fm_drv] do_one_initcall+0xbc/0x47d init/main.c:901 do_init_module+0x1b5/0x547 kernel/module.c:3456 load_module+0x6405/0x8c10 kernel/module.c:3804 __do_sys_finit_module+0x162/0x190 kernel/module.c:3898 do_syscall_64+0x9f/0x450 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe Add relevant unregister functions to fix it. Cc: Hans Verkuil <hans.verkuil@cisco.com> Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by:
-
Imre Deak authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit d9349850 ] The sequence static DEFINE_WW_CLASS(test_ww_class); struct ww_acquire_ctx ww_ctx; struct ww_mutex ww_lock_a; struct ww_mutex ww_lock_b; struct ww_mutex ww_lock_c; struct mutex lock_c; ww_acquire_init(&ww_ctx, &test_ww_class); ww_mutex_init(&ww_lock_a, &test_ww_class); ww_mutex_init(&ww_lock_b, &test_ww_class); ww_mutex_init(&ww_lock_c, &test_ww_class); mutex_init(&lock_c); ww_mutex_lock(&ww_lock_a, &ww_ctx); mutex_lock(&lock_c); ww_mutex_lock(&ww_lock_b, &ww_ctx); ww_mutex_lock(&ww_lock_c, &ww_ctx); mutex_unlock(&lock_c); (*) ww_mutex_unlock(&ww_lock_c); ww_mutex_unlock(&ww_lock_b); ww_mutex_unlock(&ww_lock_a); ww_acquire_fini(&ww_ctx); (**) will trigger the following error in __lock_release() when calling mutex_release() at **: DEBUG_LOCKS_WARN_ON(depth <= 0) The problem is that the hlock merging happening at * updates the references for test_ww_class incorrectly to 3 whereas it should've updated it to 4 (representing all the instances for ww_ctx and ww_lock_[abc]). Fix this by updating the references during merging correctly taking into account that we can have non-zero references (both for the hlock that we merge into another hlock or for the hlock we are merging into). Signed-off-by:
Imre Deak <imre.deak@intel.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: =?UTF-8?q?Ville=20Syrj=C3=A4l=C3=A4?= <ville.syrjala@linux.intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will.deacon@arm.com> Link: https://lkml.kernel.org/r/20190524201509.9199-2-imre.deak@intel.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
David S. Miller authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit 621ccc6c ] Rename _P to _P_VAL and _R to _R_VAL to avoid global namespace conflicts: drivers/media/dvb-frontends/tua6100.c: In function ‘tua6100_set_params’: drivers/media/dvb-frontends/tua6100.c:79: warning: "_P" redefined #define _P 32 In file included from ./include/acpi/platform/aclinux.h:54, from ./include/acpi/platform/acenv.h:152, from ./include/acpi/acpi.h:22, from ./include/linux/acpi.h:34, from ./include/linux/i2c.h:17, from drivers/media/dvb-frontends/tua6100.h:30, from drivers/media/dvb-frontends/tua6100.c:32: ./include/linux/ctype.h:14: note: this is the location of the previous definition #define _P 0x10 /* punct */ Signed-off-by:
-
Ioana Ciornei authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit 82c76aca ] In general, we don't want MAC drivers calling phy_attach_direct with the net_device being NULL. Add checks against this in all the functions calling it: phy_attach() and phy_connect_direct(). Signed-off-by:
Ioana Ciornei <ioana.ciornei@nxp.com> Suggested-by:
Andrew Lunn <andrew@lunn.ch> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Shailendra Verma authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit 6995a659 ] Fix to avoid possible memory leak if the decoder initialization got failed.Free the allocated memory for file handle object before return in case decoder initialization fails. Signed-off-by:
Shailendra Verma <shailendra.v@samsung.com> Signed-off-by:
-
Anirudh Gupta authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit b38ff407 ] Family of src/dst can be different from family of selector src/dst. Use xfrm selector family to validate address prefix length, while verifying new sa from userspace. Validated patch with this command: ip xfrm state add src 1.1.6.1 dst 1.1.6.2 proto esp spi 4260196 \ reqid 20004 mode tunnel aead "rfc4106(gcm(aes))" \ 0x1111016400000000000000000000000044440001 128 \ sel src 1011:1:4::2/128 sel dst 1021:1:4::2/128 dev Port5 Fixes: 07bf7908 ("xfrm: Validate address prefix lengths in the xfrm selector.") Signed-off-by:
Anirudh Gupta <anirudh.gupta@sophos.com> Acked-by:
-
Jeremy Sowden authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit 7c80eb1c ] In both functions, if pfkey_xfrm_policy2msg failed we leaked the newly allocated sk_buff. Free it on error. Fixes: 55569ce2 ("Fix conversion between IPSEC_MODE_xxx and XFRM_MODE_xxx.") Reported-by: syzbot+4f0529365f7f2208d9f0@syzkaller.appspotmail.com Signed-off-by:
Jeremy Sowden <jeremy@azazel.net> Signed-off-by:
-
Eric W. Biederman authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit f9070dc9 ] The locking in force_sig_info is not prepared to deal with a task that exits or execs (as sighand may change). The is not a locking problem in force_sig as force_sig is only built to handle synchronous exceptions. Further the function force_sig_info changes the signal state if the signal is ignored, or blocked or if SIGNAL_UNKILLABLE will prevent the delivery of the signal. The signal SIGKILL can not be ignored and can not be blocked and SIGNAL_UNKILLABLE won't prevent it from being delivered. So using force_sig rather than send_sig for SIGKILL is confusing and pointless. Because it won't impact the sending of the signal and and because using force_sig is wrong, replace force_sig with send_sig. Cc: Daniel Lezcano <daniel.lezcano@free.fr> Cc: Serge Hallyn <serge@hallyn.com> Cc: Oleg Nesterov <oleg@redhat.com> Fixes: cf3f8921 ("pidns: add reboot_pid_ns() to handle the reboot syscall") Signed-off-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
-
Jose Abreu authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit 9463c445 ] In case we don't use a given address entry we need to clear it because it could contain previous values that are no longer valid. Found out while running stmmac selftests. Signed-off-by:
Jose Abreu <joabreu@synopsys.com> Cc: Joao Pinto <jpinto@synopsys.com> Cc: David S. Miller <davem@davemloft.net> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by:
-
Kangjie Lu authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit e08f0761 ] In case ioremap fails, the fix returns -ENOMEM to avoid NULL pointer dereference. Signed-off-by:
Kangjie Lu <kjlu@umn.edu> Acked-by:
Lad, Prabhakar <prabhakar.csengg@gmail.com> Reviewed-by:
Mukesh Ojha <mojha@codeaurora.org> Signed-off-by:
-
Lubomir Rintel authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit 0c7aa329 ] The commit d790b7ed ("[media] vb2-dma-sg: move dma_(un)map_sg here") left dma_desc_nent unset. It previously contained the number of DMA descriptors as returned from dma_map_sg(). We can now (since the commit referred to above) obtain the same value from the sg_table and drop dma_desc_nent altogether. Tested on OLPC XO-1.75 machine. Doesn't affect the OLPC XO-1's Cafe driver, since that one doesn't do DMA. [mchehab+samsung@kernel.org: fix a checkpatch warning] Fixes: d790b7ed ("[media] vb2-dma-sg: move dma_(un)map_sg here") Signed-off-by:
Lubomir Rintel <lkundrak@v3.sk> Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Christophe Leroy authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit 3e03e792 ] Selftests report the following: [ 2.984845] alg: skcipher: cbc-aes-talitos encryption test failed (wrong output IV) on test vector 0, cfg="in-place" [ 2.995377] 00000000: 3d af ba 42 9d 9e b4 30 b4 22 da 80 2c 9f ac 41 [ 3.032673] alg: skcipher: cbc-des-talitos encryption test failed (wrong output IV) on test vector 0, cfg="in-place" [ 3.043185] 00000000: fe dc ba 98 76 54 32 10 [ 3.063238] alg: skcipher: cbc-3des-talitos encryption test failed (wrong output IV) on test vector 0, cfg="in-place" [ 3.073818] 00000000: 7d 33 88 93 0f 93 b2 42 This above dumps show that the actual output IV is indeed the input IV. This is due to the IV not being copied back into the request. This patch fixes that. Signed-off-by:
Christophe Leroy <christophe.leroy@c-s.fr> Reviewed-by:
Horia Geantă <horia.geanta@nxp.com> Signed-off-by:
-
Oliver Neukum authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit 6cf97230 ] dvb_usb_device_exit() frees and uses the device name in that order. Fix by storing the name in a buffer before freeing it. Signed-off-by:
Oliver Neukum <oneukum@suse.com> Reported-by: syzbot+26ec41e9f788b3eba396@syzkaller.appspotmail.com Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
-
Jeremy Sowden authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit 17f78dd1 ] A handler for BATADV_TVLV_ROAM was being registered when the translation-table was initialized, but not unregistered when the translation-table was freed. Unregister it. Fixes: 122edaa0 ("batman-adv: tvlv - convert roaming adv packet to use tvlv unicast packets") Reported-by: syzbot+d454a826e670502484b8@syzkaller.appspotmail.com Signed-off-by:
Sven Eckelmann <sven@narfation.org> Signed-off-by:
Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by:
-
Anilkumar Kolli authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit d8792393 ] Increase pulse width range from 1-2usec to 0-4usec. During data traffic HW occasionally fails detecting radar pulses, so that SW cannot get enough radar reports to achieve the success rate. Tested ath10k hw and fw: * QCA9888(10.4-3.5.1-00052) * QCA4019(10.4-3.2.1.1-00017) * QCA9984(10.4-3.6-00104) * QCA988X(10.2.4-1.0-00041) Tested ath9k hw: AR9300 Tested-by:
Tamizh chelvam <tamizhr@codeaurora.org> Signed-off-by:
Anilkumar Kolli <akolli@codeaurora.org> Signed-off-by:
-
Dan Carpenter authored
BugLink: https://bugs.launchpad.net/bugs/1840081 [ Upstream commit 5d6751ea ] The "ev->traffic_class" and "reply->ac" variables come from the network and they're used as an offset into the wmi->stream_exist_for_ac[] array. Those variables are u8 so they can be 0-255 but the stream_exist_for_ac[] array only has WMM_NUM_AC (4) elements. We need to add a couple bounds checks to prevent array overflows. I also modified one existing check from "if (traffic_class > 3) {" to "if (traffic_class >= WMM_NUM_AC) {" just to make them all consistent. Fixes: bdcd8170 (" Add ath6kl cleaned up driver") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
