- 12 Mar, 2018 1 commit
-
-
Ido Schimmel authored
Similar to the VLAN-aware bridge test, test the VLAN-unaware bridge and make sure that ping, FDB learning and flooding work as expected. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Reviewed-by:
Jiri Pirko <jiri@mellanox.com> Reviewed-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- 09 Mar, 2018 39 commits
-
-
David S. Miller authored
Julian Wiedmann says: ==================== s390/qeth: updates 2018-03-09 here is the current pile of qeth patches for net-next. Just the usual small updates and clean ups. Please apply. ==================== Signed-off-by: -
Julian Wiedmann authored
Using up 8 bytes in every ipaddr object to store SETIP/DELIP flags is rather wasteful. Except for takeover eligibility, the flag values all just depend on the address type, so determine them on demand. While at it reorder the struct to fill an alignment hole. Signed-off-by:
Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by:
-
Julian Wiedmann authored
Reduce code duplication. Signed-off-by:
-
Julian Wiedmann authored
On an IP event, current code tries to determine if the netdev belongs to a L3 card by walking all qeth cards in the system, and then all of their VLAN devices too. Short-cut the whole thing by identifying a L3 device through its netdev_ops. Signed-off-by:
-
Julian Wiedmann authored
Extract a helper that does the actual work & returns the right NOTIFY_* responses, and start putting the temporary ipaddr container objects on the stack rather than kmalloc'ing them. They are small, and this reduces the confusion of which objects actually get added to qeth's IP tables. Signed-off-by:
-
Julian Wiedmann authored
init_qdio_queues() resets the Input Queue's overall QDIO state, and positions the buffer cursor back to 0. So this is the obvious place to also reset the queue's NAPI context (in contrast to doing it rather randomly in the middle of the big set_online() path). No functional change. Signed-off-by:
-
Julian Wiedmann authored
Newly-allocated skbs default to PACKET_HOST, and eth_type_trans() is smart enough to determine any other packet type from the frame's destination address. So except for the IQD sniffer case, there is no need to set up skb->pkt_type manually. Signed-off-by:
-
Julian Wiedmann authored
napi_alloc_skb() doesn't need to disable IRQs during the allocation, and thus may save us a few cycles. Doing so requires a small fix-up in the HiperTransport path, which currently assumes a fixed NET_SKB_PAD headroom padding. napi_alloc_skb() adds an additional NET_IP_ALIGN padding, so use the proper helper for setting up the mac_header offset. Use this opportunity to convert the non-NAPI path to netdev_alloc_skb(), which means that skb->dev is now always set-up during allocation and doesn't need to be assigned manually. Signed-off-by:
-
Julian Wiedmann authored
We need to pass the *payload* length, not the L2 address length. For qeth (using eth_header()) this is merely a cosmetic change: the parameter only matters when building headers for ETH_P_802_2 or ETH_P_802_3, whereas our fake headers are built with ETH_P_IP / ETH_P_IPV6 / 0. Signed-off-by:
-
Julian Wiedmann authored
qeth implements HW-based Unicast Filtering (via SETVMAC) on L2 devices. Tell the stack, so it knows that receiving traffic for secondary addresses doesn't require full-blown promiscuous mode. Signed-off-by:
-
Julian Wiedmann authored
NETIF_F_SG support is currently limited to OSA (and for L2 even OSD) devices. Advertise it for some more device types (OSM, L2 OSX, z/VM OSA) that share the same code paths. For now, keep it switched off by default on these devices. Signed-off-by:
-
Julian Wiedmann authored
The 'portname' attribute is deprecated and setting it has no effect. Signed-off-by:
-
Julian Wiedmann authored
"s390/qeth: fix SETIP command handling" introduced a new helper, apply it driver-wide. Signed-off-by:
-
Paolo Abeni authored
Some network devices - notably ipvlan slave - are not compatible with any kind of rx_handler. Currently the hook can be installed but any configuration (bridge, bond, macsec, ...) is nonfunctional. This change allocates a priv_flag bit to mark such devices and explicitly forbid installing a rx_handler if such bit is set. The new bit is used by ipvlan slave device. Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Signed-off-by:
-
Ganesh Goudar authored
T6 cards can support up to 100 G speeds. So, increase max programmable tx rate limit to 100 Gbps. Signed-off-by:
Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by:
-
Gustavo A. R. Silva authored
In preparation to enabling -Wvla, remove VLA usage and replace it with a fixed-length array instead. Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by:
-
Vaibhav Murkute authored
Fixed a coding style issue. Signed-off-by:
Vaibhav Murkute <vaibhavmurkute88@gmail.com> Reviewed-by:
Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by:
-
David S. Miller authored
Peng Li says: ==================== fixes for configuration lost problems This patchset refactors some functions and some bugs in order to fix the configuration loss problem when resetting and setting channel number. ==================== Signed-off-by: -
Yunsheng Lin authored
This patch fixes the coalesce configuation lost problem when setting the channel number by restoring all vectors's coalesce configuation to vector 0's, because all vectors belonging to the same netdev have the same coalesce configuation for now. Signed-off-by:
Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by:
Peng Li <lipeng321@huawei.com> Signed-off-by:
-
Yunsheng Lin authored
This patch refoctors the coalesce related struct by introducing the hns3_enet_coalesce struct, in order to fix the coalesce configuation lost problem when changing the channel number. Signed-off-by:
-
Yunsheng Lin authored
Coalesce configuration will be set to default value by hns3_nic_init_vector_data during reset, which causes the coalesce configuration loss problem. This patch fixes it by setting the default value in hns3_nic_alloc_vector_data, which will not be called in the reset process. Signed-off-by:
-
Yunsheng Lin authored
There is a get_vector function, which allocate the vectors for a client, but there is not a put_vector to free the vector. This patch introduces the put_vector function in order to fix the coalesce configuration lost problem during reset process. Signed-off-by:
-
Yunsheng Lin authored
In hns3_set_ringparam, hns3_uninit_all_ring frees the memory pointed by priv->ring_data[i].ring, and hns3_change_all_ring_bd_num use that pointer without mallocing, which will cause a use-after-free problem. The patch fixes it by not freeing the memory in hns3_uninit_all_ring, and uses hns3_put_ring_config to free it when necessary. Signed-off-by:
-
Yunsheng Lin authored
Pause configuration will be set to default value by hclge_tm_schd_init during reset, which causes the RSS configuration loss problem. This patch fixes it by calling hclge_tm_init_hw during reset process , which will set the pause configuration to default value. Signed-off-by:
-
Yunsheng Lin authored
RSS configuration will be set to default value by hclge_rss_init_hw during reset, which causes the RSS configuration loss problem. This patch fixes it by setting the default value in hclge_rss_init_cfg function, which will not be called in the reset process. Signed-off-by:
-
Yunsheng Lin authored
This patch refactors the hclge_get/set_rss_tuple function in order to fix the rss configuration loss problem during reset process. Signed-off-by:
-
Yunsheng Lin authored
This patch refactors the hclge_get/set_rss function in order to fix the rss configuration loss problem during reset process. Signed-off-by:
-
David S. Miller authored
Roman Mashak says: ==================== Fix event generation for actions batch Add/Delete mode When adding or deleting a batch of entries, the kernel sends upto TCA_ACT_MAX_PRIO entries in an event to user space. However it does not consider that the action sizes may vary and require different skb sizes. For example : % cat tc-batch.sh TC="sudo /mnt/iproute2.git/tc/tc" $TC actions flush action gact for i in `seq 1 $1`; do cmd="action pass index $i " args=$args$cmd done $TC actions add $args % % ./tc-batch.sh 32 Error: Failed to fill netlink attributes while adding TC action. We have an error talking to the kernel % This patchset introduces new callback in tc_action_ops, which calculates the action size, and passes size to tcf_add_notify()/tcf_del_notify(). The patch fixes act_gact, and the rest of actions will be updated in the follow-up patches. v3: Fixed tcf_action_fill_size() to return shared attrs length when action ->get_fill_size() isn't implemented. v2: Restructured patches to make them bisectable. ==================== Signed-off-by: -
Roman Mashak authored
Signed-off-by:
Roman Mashak <mrv@mojatatu.com> Signed-off-by:
-
Roman Mashak authored
Introduce routines to calculate size of the shared tc netlink attributes and the full message size including netlink header and tc service header. Update add/delete action logic to have the size for event messages, the size is passed to tcf_add_notify() and tcf_del_notify() where the notification message is being allocated and constructed. Signed-off-by:
-
Roman Mashak authored
Add a new callback in tc_action_ops, it will be needed by the tc actions to compute its size when a ADD/DELETE notification message is constructed. This routine has to take into account optional/variable size TLVs specific per action. Signed-off-by:
-
Roman Mashak authored
Introduce a new function argument to carry total attributes size for correct allocation of skb in event messages. Signed-off-by:
-
Eric Dumazet authored
fallback tunnels (like tunl0, gre0, gretap0, erspan0, sit0, ip6tnl0, ip6gre0) are automatically created when the corresponding module is loaded. These tunnels are also automatically created when a new network namespace is created, at a great cost. In many cases, netns are used for isolation purposes, and these extra network devices are a waste of resources. We are using thousands of netns per host, and hit the netns creation/delete bottleneck a lot. (Many thanks to Kirill for recent work on this) Add a new sysctl so that we can opt-out from this automatic creation. Note that these tunnels are still created for the initial namespace, to be the least intrusive for typical setups. Tested: lpk43:~# cat add_del_unshare.sh for i in `seq 1 40` do (for j in `seq 1 100` ; do unshare -n /bin/true >/dev/null ; done) & done wait lpk43:~# echo 0 >/proc/sys/net/core/fb_tunnels_only_for_init_net lpk43:~# time ./add_del_unshare.sh real 0m37.521s user 0m0.886s sys 7m7.084s lpk43:~# echo 1 >/proc/sys/net/core/fb_tunnels_only_for_init_net lpk43:~# time ./add_del_unshare.sh real 0m4.761s user 0m0.851s sys 1m8.343s lpk43:~# Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Brenda J. Butler authored
With option -P, the test script will pause just before the post_suite functions are called. This allows the tester to inspect the system before it is torn down. Signed-off-by:
Brenda J. Butler <bjb@mojatatu.com> Signed-off-by:
-
Brenda J. Butler authored
When processing the commands in the test cases, substitute the test id for $TESTID. This helps to make more flexible tests. For example, the testid can be given as a command line argument. As an example, if we wish to save the test output to a file named for the test case, we can write in the test case: "cmdUnderTest": "some test command | tee -a $TESTID.out" Signed-off-by:
-
Andrew Lunn authored
Call the common irq free function, rather than going recursive and blowing away the stack, followed by the machine. Fixes: 294d711e ("net: dsa: mv88e6xxx: Poll when no interrupt defined") Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Roman Mashak authored
Signed-off-by:
Davide Caratti <dcaratti@redhat.com> Signed-off-by:
-
Alexander Kurz authored
Remove the duplicated code for asix88179_178a bind and reset methods. Signed-off-by:
Alexander Kurz <akurz@blala.de> Signed-off-by:
-
Alexander Kurz authored
The permanent address of asix88179_178a devices is read at probe time and should not be overwritten later. Otherwise it may be overwritten unintentionally with a configured address. Signed-off-by:
-
