- 20 Dec, 2018 27 commits
-
-
Benjamin Herrenschmidt authored
The bamboo dts has a bug: it uses a non-naturally aligned range for PCI memory space. This isnt' supported by the code, thus causing PCI to break on this system. This is due to the fact that while the chip memory map has 1G reserved for PCI memory, it's only 512M aligned. The code doesn't know how to split that into 2 different PMMs and fails, so limit the region to 512M. Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au>
-
Darren Stevens authored
Add a IRQ init routine for the Nemo board which inits and attatches the i8259 found in the SB600, and a cascade routine to dispatch the interrupts. Signed-off-by:
Darren Stevens <darren@stevens-zone.net> Signed-off-by:
-
Darren Stevens authored
Add routines for Nemo specific devices to init at boot time, these being board level power-off and SB600's rtc. Also add a run time variable to prevent these being activated if we boot on a reference board. Signed-off-by:
-
Darren Stevens authored
Add a IRQ init routine for the Nemo board which inits and attatches the i8259 found in the SB600, and a cascade routine to dispatch the interrupts. Signed-off-by:
-
Darren Stevens authored
The A-Eon Amigaone X1000's Nemo motherboard has an AMD SB600 connected to one of the PCI-e root ports on its PaSemi Pwrficient 1628M SoC. Normally the SB600 southbridge would be connected to a hidden PCI-e port on the system's northbridge, and as a result doesn't fully comply with the PCI-e spec. Add code to relax the PCI-e detection in both the root port and the Linux kernel allowing on board devices to be detected. Signed-off-by:
-
Christophe Leroy authored
As several other arches including x86, this patch makes it explicit that a bad page fault is a NULL pointer dereference when the fault address is lower than PAGE_SIZE In the mean time, this page makes all bad_page_fault() messages shorter so that they remain on one single line. And it prefixes them by "BUG: " so that they get easily grepped. Signed-off-by:
Christophe Leroy <christophe.leroy@c-s.fr> [mpe: Avoid pr_cont()] Signed-off-by:
-
Dmitry V. Levin authored
Combine the SYSCALL_EMU and SYSCALL_TRACE handling so that we only call tracehook_report_syscall_entry() in one place. Signed-off-by:
Dmitry V. Levin <ldv@altlinux.org> [mpe: Flesh out change log, s/cached_flags/flags/, reflow comments] Signed-off-by:
-
Christoph Hellwig authored
Powerpc has somewhat odd usage where ZONE_DMA is used for all memory on common 64-bit configfs, and ZONE_DMA32 is used for 31-bit schemes. Move to a scheme closer to what other architectures use (and I dare to say the intent of the system): - ZONE_DMA: optionally for memory < 31-bit (64-bit embedded only) - ZONE_NORMAL: everything addressable by the kernel - ZONE_HIGHMEM: memory > 32-bit for 32-bit kernels Also provide information on how ZONE_DMA is used by defining ARCH_ZONE_DMA_BITS. Contains various fixes from Benjamin Herrenschmidt. Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Christoph Hellwig authored
The CXL code never even looks at the dma mask, so there is no good reason for this sanity check. Remove it because it gets in the way of the dma ops refactoring. Signed-off-by:
Andrew Donnellan <andrew.donnellan@au1.ibm.com> Signed-off-by:
-
Christoph Hellwig authored
The implemementation for the CONFIG_NOT_COHERENT_CACHE case doesn't share any code with the one for systems with coherent caches. Split it off and merge it with the helpers in dma-noncoherent.c that have no other callers. Signed-off-by:
-
Christoph Hellwig authored
Signed-off-by:
-
Christoph Hellwig authored
Signed-off-by:
-
Christoph Hellwig authored
Signed-off-by:
-
Christoph Hellwig authored
This function is internal to the DMA API implementation. Instead use the DMA API to properly unmap. Note that the DMA API usage in this driver is a disaster and urgently needs some work - it is missing all the unmaps, seems to do a secondary map where it looks like it should to a unmap in one place to work around cache coherency and the directions passed in seem to be partially wrong. Signed-off-by:
Christian Lamparter <chunkeey@gmail.com> Signed-off-by:
-
Christoph Hellwig authored
The unmap methods need to transfer memory ownership back from the device to the cpu by identical means as dma_sync_*_to_cpu. I'm not sure powerpc needs to do any work in this transfer direction, but given that it does invalidate the caches in dma_sync_*_to_cpu already we should make sure we also do so on unmapping. Signed-off-by:
-
Christoph Hellwig authored
AMIGAONE selects NOT_COHERENT_CACHE, so we better allow it. Signed-off-by:
-
Christophe Leroy authored
This patch fixes early DEBUG messages in prom.c: - Use %px instead of %p to see the addresses - Cast memblock_phys_mem_size() with (unsigned long long) to avoid build failure when phys_addr_t is not 64 bits. Signed-off-by:
-
Greg Kurz authored
All fields in the PE are big-endian. Use cpu_to_be32() like everywhere else something is written to the PE. Otherwise a wrong TID will be used by the NPU. If this TID happens to point to an existing thread sharing the same mm, it could be woken up by error. This is highly improbable though. The likely outcome of this is the NPU not finding the target thread and forcing the AFU into sending an interrupt, which userspace is supposed to handle anyway. Fixes: e948e06f ("ocxl: Expose the thread_id needed for wait on POWER9") Cc: stable@vger.kernel.org # v4.18 Signed-off-by:
Greg Kurz <groug@kaod.org> Acked-by:
-
Joel Stanley authored
When building for ppc32 with clang these flags are unsupported: -ffixed-r2 and -mmultiple llvm's lib/Target/PowerPC/PPCRegisterInfo.cpp marks r2 as reserved on when building for SVR4ABI and !ppc64: // The SVR4 ABI reserves r2 and r13 if (Subtarget.isSVR4ABI()) { // We only reserve r2 if we need to use the TOC pointer. If we have no // explicit uses of the TOC pointer (meaning we're a leaf function with // no constant-pool loads, etc.) and we have no potential uses inside an // inline asm block, then we can treat r2 has an ordinary callee-saved // register. const PPCFunctionInfo *FuncInfo = MF.getInfo<PPCFunctionInfo>(); if (!TM.isPPC64() || FuncInfo->usesTOCBasePtr() || MF.hasInlineAsm()) markSuperRegs(Reserved, PPC::R2); // System-reserved register markSuperRegs(Reserved, PPC::R13); // Small Data Area pointer register } This means we can safely omit -ffixed-r2 when building for 32-bit targets. The -mmultiple/-mno-multiple flags are not supported by clang, so platforms that might support multiple miss out on using multiple word instructions. We wrap these flags in cc-option so that when Clang gains support the kernel will be able use these flags. Clang 8 can then build a ppc44x_defconfig which boots in Qemu: make CC=clang-8 ARCH=powerpc CROSS_COMPILE=powerpc-linux-gnu- ppc44x_defconfig ./scripts/config -e CONFIG_DEVTMPFS -d DEVTMPFS_MOUNT make CC=clang-8 ARCH=powerpc CROSS_COMPILE=powerpc-linux-gnu- qemu-system-ppc -M bamboo \ -kernel arch/powerpc/boot/zImage \ -dtb arch/powerpc/boot/dts/bamboo.dtb \ -initrd ~/ppc32-440-rootfs.cpio \ -nographic -serial stdio -monitor pty -append "console=ttyS0" Link: https://github.com/ClangBuiltLinux/linux/issues/261 Link: https://bugs.llvm.org/show_bug.cgi?id=39556 Link: https://bugs.llvm.org/show_bug.cgi?id=39555Signed-off-by:Joel Stanley <joel@jms.id.au> Reviewed-by:
Nick Desaulniers <ndesaulniers@google.com> Signed-off-by:
-
Joel Stanley authored
We cannot build these files with clang as it does not allow altivec instructions in assembly when -msoft-float is passed. Jinsong Ji <jji@us.ibm.com> wrote: > We currently disable Altivec/VSX support when enabling soft-float. So > any usage of vector builtins will break. > > Enable Altivec/VSX with soft-float may need quite some clean up work, so > I guess this is currently a limitation. > > Removing -msoft-float will make it work (and we are lucky that no > floating point instructions will be generated as well). This is a workaround until the issue is resolved in clang. Link: https://bugs.llvm.org/show_bug.cgi?id=31177 Link: https://github.com/ClangBuiltLinux/linux/issues/239Signed-off-by:
-
Madhavan Srinivasan authored
Remove PM_L2_ST_MISS and PM_L2_ST from HW cache event array since these are bus events. And these needs to be programmed in groups. Hence remove them. Fixes: f1fb60bf ('powerpc/perf: Export Power9 generic and cache events to sysfs') Signed-off-by:
Madhavan Srinivasan <maddy@linux.vnet.ibm.com> Signed-off-by:
-
Madhavan Srinivasan authored
In previous generation processors, both bus events and direct events of performance monitoring unit can be individually programmabled and monitored in PMCs. But in Power9, L2/L3 bus events are always available as a "bank" of 4 events. To obtain the counts for any of the l2/l3 bus events in a given bank, the user will have to program PMC4 with corresponding l2/l3 bus event for that bank. Patch enforce two contraints incase of L2/L3 bus events. 1)Any L2/L3 event when programmed is also expected to program corresponding PMC4 event from that group. 2)PMC4 event should always been programmed first due to group constraint logic limitation For ex. consider these L3 bus events PM_L3_PF_ON_CHIP_MEM (0x460A0), PM_L3_PF_MISS_L3 (0x160A0), PM_L3_CO_MEM (0x260A0), PM_L3_PF_ON_CHIP_CACHE (0x360A0), 1) This is an INVALID group for L3 Bus event monitoring, since it is missing PMC4 event. perf stat -e "{r160A0,r260A0,r360A0}" < > And this is a VALID group for L3 Bus events: perf stat -e "{r460A0,r160A0,r260A0,r360A0}" < > 2) This is an INVALID group for L3 Bus event monitoring, since it is missing PMC4 event. perf stat -e "{r260A0,r360A0}" < > And this is a VALID group for L3 Bus events: perf stat -e "{r460A0,r260A0,r360A0}" < > 3) This is an INVALID group for L3 Bus event monitoring, since it is missing PMC4 event. perf stat -e "{r360A0}" < > And this is a VALID group for L3 Bus events: perf stat -e "{r460A0,r360A0}" < > Patch here implements group constraint logic suggested by Michael Ellerman. Signed-off-by: -
Madhavan Srinivasan authored
Raw event code has couple of fields "unit" and "cache" in it, to capture the "unit" to monitor for a given pmcxsel and cache reload qualifier to program in MMCR1. isa207_get_constraint() refers "unit" field to update the MMCRC (L2/L3) Event bus control fields with "cache" bits of the raw event code. These are power8 specific and not supported by PowerISA v3.0 pmu. So wrap the checks to be power8 specific. Also, "cache" bit field is referred to update MMCR1[16:17] and this check can be power8 specific. Fixes: 7ffd948f ('powerpc/perf: factor out power8 pmu functions') Signed-off-by:
-
Madhavan Srinivasan authored
Update the raw event code comment in power9-pmu.c with respect to "cache" bits, since power9 MMCRC does not support these. Signed-off-by:
-
Madhavan Srinivasan authored
On each sample, Sample Instruction Event Register (SIER) content is saved in pt_regs. SIER does not have a entry as-is in the pt_regs but instead, SIER content is saved in the "dar" register of pt_regs. Patch adds another entry to the perf_regs structure to include the "SIER" printing which internally maps to the "dar" of pt_regs. It also check for the SIER availability in the platform and present value accordingly Signed-off-by:
-
Madhavan Srinivasan authored
MMCRA[34:36] and MMCRA[38:44] expose the thresholding counter value. Thresholding counter can be used to count latency cycles such as load miss to reload. But threshold counter value is not relevant when the sampled instruction type is unknown or reserved. Patch to fix the thresholding counter value to zero when sampled instruction type is unknown or reserved. Fixes: 170a315f('powerpc/perf: Support to export MMCRA[TEC*] field to userspace') Signed-off-by:
-
Aneesh Kumar K.V authored
In commit 2865d08d ("powerpc/mm: Move the DSISR_PROTFAULT sanity check") we moved the protection fault access check before the vma lookup. That means we hit that WARN_ON when user space accesses a kernel address. Before that commit this was handled by find_vma() not finding vma for the kernel address and considering that access as bad area access. Avoid the confusing WARN_ON and convert that to a ratelimited printk. With the patch we now get: for load: a.out[5997]: User access of kernel address (c00000000000dea0) - exploit attempt? (uid: 1000) a.out[5997]: segfault (11) at c00000000000dea0 nip 1317c0798 lr 7fff80d6441c code 1 in a.out[1317c0000+10000] a.out[5997]: code: 60000000 60420000 3c4c0002 38427790 4bffff20 3c4c0002 38427784 fbe1fff8 a.out[5997]: code: f821ffc1 7c3f0b78 60000000 e9228030 <89290000> 993f002f 60000000 383f0040 for exec: a.out[6067]: User access of kernel address (c00000000000dea0) - exploit attempt? (uid: 1000) a.out[6067]: segfault (11) at c00000000000dea0 nip c00000000000dea0 lr 129d507b0 code 1 a.out[6067]: Bad NIP, not dumping instructions. Fixes: 2865d08d ("powerpc/mm: Move the DSISR_PROTFAULT sanity check") Signed-off-by:
Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Tested-by:
Breno Leitao <leitao@debian.org> [mpe: Don't split printk() string across lines] Signed-off-by:
-
- 19 Dec, 2018 13 commits
-
-
Christophe Leroy authored
The 603 doesn't have a HASH table, TLB misses are handled by software. It is then possible to generate page fault when _PAGE_EXEC is not set like in nohash/32. There is one "reserved" PTE bit available, this patch uses it for _PAGE_EXEC. In order to support it, set_pte_filter() and set_access_flags_filter() are made common, and the handling is made dependent on MMU_FTR_HPTE_TABLE Signed-off-by:
-
Christophe Leroy authored
Define slice_init_new_context_exec() at all time to avoid Signed-off-by:
-
Christophe Leroy authored
With the following piece of code, the following compilation warning is encountered: if (_IOC_DIR(ioc) != _IOC_NONE) { int verify = _IOC_DIR(ioc) & _IOC_READ ? VERIFY_WRITE : VERIFY_READ; if (!access_ok(verify, ioarg, _IOC_SIZE(ioc))) { drivers/platform/test/dev.c: In function 'my_ioctl': drivers/platform/test/dev.c:219:7: warning: unused variable 'verify' [-Wunused-variable] int verify = _IOC_DIR(ioc) & _IOC_READ ? VERIFY_WRITE : VERIFY_READ; This patch fixes it by referencing 'type' in the macro allthough doing nothing with it. Signed-off-by: -
Christophe Leroy authored
commit f21f49ea ("[POWERPC] Remove the dregs of APUS support from arch/powerpc") removed CONFIG_APUS, but forgot to remove the logic which adapts tophys() and tovirt() for it. This patch removes the last stale pieces. Signed-off-by:
-
Christophe Leroy authored
mfsrin() takes segment num from bits 31-28 (IBM bits 0-3). Signed-off-by:
-
Christophe Leroy authored
This patch adds STACK_FRAME_REGS_MARKER in the stack at exception entry in order to see interrupts in call traces as below: [ 0.013964] Call Trace: [ 0.014014] [c0745db0] [c007a9d4] tick_periodic.constprop.5+0xd8/0x104 (unreliable) [ 0.014086] [c0745dc0] [c007aa20] tick_handle_periodic+0x20/0x9c [ 0.014181] [c0745de0] [c0009cd0] timer_interrupt+0xa0/0x264 [ 0.014258] [c0745e10] [c000e484] ret_from_except+0x0/0x14 [ 0.014390] --- interrupt: 901 at console_unlock.part.7+0x3f4/0x528 [ 0.014390] LR = console_unlock.part.7+0x3f0/0x528 [ 0.014455] [c0745ee0] [c0050334] console_unlock.part.7+0x114/0x528 (unreliable) [ 0.014542] [c0745f30] [c00524e0] register_console+0x3d8/0x44c [ 0.014625] [c0745f60] [c0675aac] cpm_uart_console_init+0x18/0x2c [ 0.014709] [c0745f70] [c06614f4] console_init+0x114/0x1cc [ 0.014795] [c0745fb0] [c0658b68] start_kernel+0x300/0x3d8 [ 0.014864] [c0745ff0] [c00022cc] start_here+0x44/0x98 Signed-off-by:
-
Christophe Leroy authored
This patch fixes the loop in p_block_mapped() and v_block_mapped() to scan the entire bat_addrs[] array. Signed-off-by:
-
Christophe Leroy authored
Depending on the CONFIG selected, many of the MMU features are not possible. Lets only get the possible ones in MMU_FTRS_POSSIBLE. This allows gcc to get rid at compile time of code related to not possible features. Signed-off-by:
-
Christophe Leroy authored
Instead of hardcoding reset vector restore, use patch_instruction() Signed-off-by:
-
Christophe Leroy authored
Use patch sites and associated helpers to manage TLB handlers patching instead of hardcoding. Signed-off-by:
-
Christophe Leroy authored
Instead of hardcoding code modifications, use code patching functions. Signed-off-by:
-
Christophe Leroy authored
Instead of hardcoding the TLB handlers patching, use the newly created modify_instruction_site() helper. Signed-off-by:
-
Christophe Leroy authored
Use patch_sites and the new modify_instruction_site() function instead of hardcoding hash functions patching. Signed-off-by:
-
