- 31 May, 2019 40 commits
-
-
Stanley Chu authored
[ Upstream commit 3b141e8c ] For regulators used by UFS, vcc, vccq and vccq2 will have voltage range initialized by ufshcd_populate_vreg(), however other regulators may have undefined voltage range if dt-bindings have no such definition. In above undefined case, both "min_uV" and "max_uV" fields in ufs_vreg struct will be zero values and these values will be configured on regulators in different power modes. Currently this may have no harm if both "min_uV" and "max_uV" always keep "zero values" because regulator_set_voltage() will always bypass such invalid values and return "good" results. However improper values shall be fixed to avoid potential bugs. Simply bypass voltage configuration if voltage range is not defined. Signed-off-by:
Stanley Chu <stanley.chu@mediatek.com> Reviewed-by:
Avri Altman <avri.altman@wdc.com> Acked-by:
Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Stanley Chu authored
[ Upstream commit 0487fff7 ] Currently if a regulator has "<name>-fixed-regulator" property in device tree, it will skip current limit initialization. This lead to a zero "max_uA" value in struct ufs_vreg. However, "regulator_set_load" operation shall be required on regulators which have valid current limits, otherwise a zero "max_uA" set by "regulator_set_load" may cause unexpected behavior when this regulator is enabled or set as high power mode. Similarly, in device's icc_level configuration flow, the target icc_level shall be updated if regulator also has valid current limit, otherwise a wrong icc_level will be calculated by zero "max_uA" and thus causes unexpected results after it is written to device. Signed-off-by:
-
Piotr Figiel authored
[ Upstream commit 24d413a3 ] Fix a race which leads to an Oops with NULL pointer dereference. The dereference is in brcmf_config_dongle() when cfg_to_ndev() attempts to get net_device structure of interface with index 0 via if2bss mapping. This shouldn't fail because of check for bus being ready in brcmf_netdev_open(), but it's not synchronised with USB disconnect and there is a race: after the check the bus can be marked down and the mapping for interface 0 may be gone. Solve this by modifying disconnect handling so that the removal of mapping of ifidx to brcmf_if structure happens after netdev removal (which is synchronous with brcmf_netdev_open() thanks to rtln being locked in devinet_ioctl()). This assures brcmf_netdev_open() returns before the mapping is removed during disconnect. Unable to handle kernel NULL pointer dereference at virtual address 00000008 pgd = bcae2612 [00000008] *pgd=8be73831 Internal error: Oops: 17 [#1] PREEMPT SMP ARM Modules linked in: brcmfmac brcmutil nf_log_ipv4 nf_log_common xt_LOG xt_limit iptable_mangle xt_connmark xt_tcpudp xt_conntrack nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 iptable_filter ip_tables x_tables usb_f_mass_storage usb_f_rndis u_ether usb_serial_simple usbserial cdc_acm smsc95xx usbnet ci_hdrc_imx ci_hdrc usbmisc_imx ulpi 8250_exar 8250_pci 8250 8250_base libcomposite configfs udc_core [last unloaded: brcmutil] CPU: 2 PID: 24478 Comm: ifconfig Not tainted 4.19.23-00078-ga62866d-dirty #115 Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) PC is at brcmf_cfg80211_up+0x94/0x29c [brcmfmac] LR is at brcmf_cfg80211_up+0x8c/0x29c [brcmfmac] pc : [<7f26a91c>] lr : [<7f26a914>] psr: a0070013 sp : eca99d28 ip : 00000000 fp : ee9c6c00 r10: 00000036 r9 : 00000000 r8 : ece4002c r7 : edb5b800 r6 : 00000000 r5 : 80f08448 r4 : edb5b968 r3 : ffffffff r2 : 00000000 r1 : 00000002 r0 : 00000000 Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none Control: 10c5387d Table: 7ca0c04a DAC: 00000051 Process ifconfig (pid: 24478, stack limit = 0xd9e85a0e) Stack: (0xeca99d28 to 0xeca9a000) 9d20: 00000000 80f873b0 0000000d 80f08448 eca99d68 50d45f32 9d40: 7f27de94 ece40000 80f08448 80f08448 7f27de94 ece4002c 00000000 00000036 9d60: ee9c6c00 7f27262c 00001002 50d45f32 ece40000 00000000 80f08448 80772008 9d80: 00000001 00001043 00001002 ece40000 00000000 50d45f32 ece40000 00000001 9da0: 80f08448 00001043 00001002 807723d0 00000000 50d45f32 80f08448 eca99e58 9dc0: 80f87113 50d45f32 80f08448 ece40000 ece40138 00001002 80f08448 00000000 9de0: 00000000 80772434 edbd5380 eca99e58 edbd5380 80f08448 ee9c6c0c 80805f70 9e00: 00000000 ede08e00 00008914 ece40000 00000014 ee9c6c0c 600c0013 00001043 9e20: 0208a8c0 ffffffff 00000000 50d45f32 eca98000 80f08448 7ee9fc38 00008914 9e40: 80f68e40 00000051 eca98000 00000036 00000003 80808b9c 6e616c77 00000030 9e60: 00000000 00000000 00001043 0208a8c0 ffffffff 00000000 80f08448 00000000 9e80: 00000000 816d8b20 600c0013 00000001 ede09320 801763d4 00000000 50d45f32 9ea0: eca98000 80f08448 7ee9fc38 50d45f32 00008914 80f08448 7ee9fc38 80f68e40 9ec0: ed531540 8074721c 00000800 00000001 00000000 6e616c77 00000030 00000000 9ee0: 00000000 00001002 0208a8c0 ffffffff 00000000 50d45f32 80f08448 7ee9fc38 9f00: ed531560 ec8fc900 80285a6c 80285138 edb910c0 00000000 ecd91008 ede08e00 9f20: 80f08448 00000000 00000000 816d8b20 600c0013 00000001 ede09320 801763d4 9f40: 00000000 50d45f32 00021000 edb91118 edb910c0 80f08448 01b29000 edb91118 9f60: eca99f7c 50d45f32 00021000 ec8fc900 00000003 ec8fc900 00008914 7ee9fc38 9f80: eca98000 00000036 00000003 80285a6c 00086364 7ee9fe1c 000000c3 00000036 9fa0: 801011c4 80101000 00086364 7ee9fe1c 00000003 00008914 7ee9fc38 00086364 9fc0: 00086364 7ee9fe1c 000000c3 00000036 0008630c 7ee9fe1c 7ee9fc38 00000003 9fe0: 000a42b8 7ee9fbd4 00019914 76e09acc 600c0010 00000003 00000000 00000000 [<7f26a91c>] (brcmf_cfg80211_up [brcmfmac]) from [<7f27262c>] (brcmf_netdev_open+0x74/0xe8 [brcmfmac]) [<7f27262c>] (brcmf_netdev_open [brcmfmac]) from [<80772008>] (__dev_open+0xcc/0x150) [<80772008>] (__dev_open) from [<807723d0>] (__dev_change_flags+0x168/0x1b4) [<807723d0>] (__dev_change_flags) from [<80772434>] (dev_change_flags+0x18/0x48) [<80772434>] (dev_change_flags) from [<80805f70>] (devinet_ioctl+0x67c/0x79c) [<80805f70>] (devinet_ioctl) from [<80808b9c>] (inet_ioctl+0x210/0x3d4) [<80808b9c>] (inet_ioctl) from [<8074721c>] (sock_ioctl+0x350/0x524) [<8074721c>] (sock_ioctl) from [<80285138>] (do_vfs_ioctl+0xb0/0x9b0) [<80285138>] (do_vfs_ioctl) from [<80285a6c>] (ksys_ioctl+0x34/0x5c) [<80285a6c>] (ksys_ioctl) from [<80101000>] (ret_fast_syscall+0x0/0x28) Exception stack(0xeca99fa8 to 0xeca99ff0) 9fa0: 00086364 7ee9fe1c 00000003 00008914 7ee9fc38 00086364 9fc0: 00086364 7ee9fe1c 000000c3 00000036 0008630c 7ee9fe1c 7ee9fc38 00000003 9fe0: 000a42b8 7ee9fbd4 00019914 76e09acc Code: e5970328 eb002021 e1a02006 e3a01002 (e5909008) ---[ end trace 5cbac2333f3ac5df ]--- Signed-off-by:
Piotr Figiel <p.figiel@camlintechnologies.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Piotr Figiel authored
[ Upstream commit db3b9e2e ] It was observed that rarely during USB disconnect happening shortly after connect (before full initialization completes) usb_hub_wq would wait forever for the dev_init_lock to be unlocked. dev_init_lock would remain locked though because of infinite wait during usb_kill_urb: [ 2730.656472] kworker/0:2 D 0 260 2 0x00000000 [ 2730.660700] Workqueue: events request_firmware_work_func [ 2730.664807] [<809dca20>] (__schedule) from [<809dd164>] (schedule+0x4c/0xac) [ 2730.670587] [<809dd164>] (schedule) from [<8069af44>] (usb_kill_urb+0xdc/0x114) [ 2730.676815] [<8069af44>] (usb_kill_urb) from [<7f258b50>] (brcmf_usb_free_q+0x34/0xa8 [brcmfmac]) [ 2730.684833] [<7f258b50>] (brcmf_usb_free_q [brcmfmac]) from [<7f2517d4>] (brcmf_detach+0xa0/0xb8 [brcmfmac]) [ 2730.693557] [<7f2517d4>] (brcmf_detach [brcmfmac]) from [<7f251a34>] (brcmf_attach+0xac/0x3d8 [brcmfmac]) [ 2730.702094] [<7f251a34>] (brcmf_attach [brcmfmac]) from [<7f2587ac>] (brcmf_usb_probe_phase2+0x468/0x4a0 [brcmfmac]) [ 2730.711601] [<7f2587ac>] (brcmf_usb_probe_phase2 [brcmfmac]) from [<7f252888>] (brcmf_fw_request_done+0x194/0x220 [brcmfmac]) [ 2730.721795] [<7f252888>] (brcmf_fw_request_done [brcmfmac]) from [<805748e4>] (request_firmware_work_func+0x4c/0x88) [ 2730.731125] [<805748e4>] (request_firmware_work_func) from [<80141474>] (process_one_work+0x228/0x808) [ 2730.739223] [<80141474>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564) [ 2730.746105] [<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c) [ 2730.752227] [<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20) [ 2733.099695] kworker/0:3 D 0 1065 2 0x00000000 [ 2733.103926] Workqueue: usb_hub_wq hub_event [ 2733.106914] [<809dca20>] (__schedule) from [<809dd164>] (schedule+0x4c/0xac) [ 2733.112693] [<809dd164>] (schedule) from [<809e2a8c>] (schedule_timeout+0x214/0x3e4) [ 2733.119621] [<809e2a8c>] (schedule_timeout) from [<809dde2c>] (wait_for_common+0xc4/0x1c0) [ 2733.126810] [<809dde2c>] (wait_for_common) from [<7f258d00>] (brcmf_usb_disconnect+0x1c/0x4c [brcmfmac]) [ 2733.135206] [<7f258d00>] (brcmf_usb_disconnect [brcmfmac]) from [<8069e0c8>] (usb_unbind_interface+0x5c/0x1e4) [ 2733.143943] [<8069e0c8>] (usb_unbind_interface) from [<8056d3e8>] (device_release_driver_internal+0x164/0x1fc) [ 2733.152769] [<8056d3e8>] (device_release_driver_internal) from [<8056c078>] (bus_remove_device+0xd0/0xfc) [ 2733.161138] [<8056c078>] (bus_remove_device) from [<8056977c>] (device_del+0x11c/0x310) [ 2733.167939] [<8056977c>] (device_del) from [<8069cba8>] (usb_disable_device+0xa0/0x1cc) [ 2733.174743] [<8069cba8>] (usb_disable_device) from [<8069507c>] (usb_disconnect+0x74/0x1dc) [ 2733.181823] [<8069507c>] (usb_disconnect) from [<80695e88>] (hub_event+0x478/0xf88) [ 2733.188278] [<80695e88>] (hub_event) from [<80141474>] (process_one_work+0x228/0x808) [ 2733.194905] [<80141474>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564) [ 2733.201724] [<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c) [ 2733.207913] [<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20) It was traced down to a case where usb_kill_urb would be called on an URB structure containing more or less random data, including large number in its use_count. During the debugging it appeared that in brcmf_usb_free_q() the traversal over URBs' lists is not synchronized with operations on those lists in brcmf_usb_rx_complete() leading to handling brcmf_usbdev_info structure (holding lists' head) as lists' element and in result causing above problem. Fix it by walking through all URBs during brcmf_cancel_all_urbs using the arrays of requests instead of linked lists. Signed-off-by:
-
Piotr Figiel authored
[ Upstream commit a9fd0953 ] Leaving dev_init_lock mutex locked in probe causes BUG and a WARNING when kernel is compiled with CONFIG_PROVE_LOCKING. Convert mutex to completion which silences those warnings and improves code readability. Fix below errors when connecting the USB WiFi dongle: brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43143 for chip BCM43143/2 BUG: workqueue leaked lock or atomic: kworker/0:2/0x00000000/434 last function: hub_event 1 lock held by kworker/0:2/434: #0: 18d5dcdf (&devinfo->dev_init_lock){+.+.}, at: brcmf_usb_probe+0x78/0x550 [brcmfmac] CPU: 0 PID: 434 Comm: kworker/0:2 Not tainted 4.19.23-00084-g454a789-dirty #123 Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) Workqueue: usb_hub_wq hub_event [<8011237c>] (unwind_backtrace) from [<8010d74c>] (show_stack+0x10/0x14) [<8010d74c>] (show_stack) from [<809c4324>] (dump_stack+0xa8/0xd4) [<809c4324>] (dump_stack) from [<8014195c>] (process_one_work+0x710/0x808) [<8014195c>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564) [<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c) [<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20) Exception stack(0xed1d9fb0 to 0xed1d9ff8) 9fa0: 00000000 00000000 00000000 00000000 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 ====================================================== WARNING: possible circular locking dependency detected 4.19.23-00084-g454a789-dirty #123 Not tainted ------------------------------------------------------ kworker/0:2/434 is trying to acquire lock: e29cf799 ((wq_completion)"events"){+.+.}, at: process_one_work+0x174/0x808 but task is already holding lock: 18d5dcdf (&devinfo->dev_init_lock){+.+.}, at: brcmf_usb_probe+0x78/0x550 [brcmfmac] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (&devinfo->dev_init_lock){+.+.}: mutex_lock_nested+0x1c/0x24 brcmf_usb_probe+0x78/0x550 [brcmfmac] usb_probe_interface+0xc0/0x1bc really_probe+0x228/0x2c0 __driver_attach+0xe4/0xe8 bus_for_each_dev+0x68/0xb4 bus_add_driver+0x19c/0x214 driver_register+0x78/0x110 usb_register_driver+0x84/0x148 process_one_work+0x228/0x808 worker_thread+0x2c/0x564 kthread+0x13c/0x16c ret_from_fork+0x14/0x20 (null) -> #1 (brcmf_driver_work){+.+.}: worker_thread+0x2c/0x564 kthread+0x13c/0x16c ret_from_fork+0x14/0x20 (null) -> #0 ((wq_completion)"events"){+.+.}: process_one_work+0x1b8/0x808 worker_thread+0x2c/0x564 kthread+0x13c/0x16c ret_from_fork+0x14/0x20 (null) other info that might help us debug this: Chain exists of: (wq_completion)"events" --> brcmf_driver_work --> &devinfo->dev_init_lock Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&devinfo->dev_init_lock); lock(brcmf_driver_work); lock(&devinfo->dev_init_lock); lock((wq_completion)"events"); *** DEADLOCK *** 1 lock held by kworker/0:2/434: #0: 18d5dcdf (&devinfo->dev_init_lock){+.+.}, at: brcmf_usb_probe+0x78/0x550 [brcmfmac] stack backtrace: CPU: 0 PID: 434 Comm: kworker/0:2 Not tainted 4.19.23-00084-g454a789-dirty #123 Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) Workqueue: events request_firmware_work_func [<8011237c>] (unwind_backtrace) from [<8010d74c>] (show_stack+0x10/0x14) [<8010d74c>] (show_stack) from [<809c4324>] (dump_stack+0xa8/0xd4) [<809c4324>] (dump_stack) from [<80172838>] (print_circular_bug+0x210/0x330) [<80172838>] (print_circular_bug) from [<80175940>] (__lock_acquire+0x160c/0x1a30) [<80175940>] (__lock_acquire) from [<8017671c>] (lock_acquire+0xe0/0x268) [<8017671c>] (lock_acquire) from [<80141404>] (process_one_work+0x1b8/0x808) [<80141404>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564) [<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c) [<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20) Exception stack(0xed1d9fb0 to 0xed1d9ff8) 9fa0: 00000000 00000000 00000000 00000000 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 Signed-off-by:
-
Arnd Bergmann authored
[ Upstream commit d825db34 ] Clang warns about what is clearly a case of passing an uninitalized variable into a static function: drivers/net/wireless/broadcom/b43/phy_lp.c:1852:23: error: variable 'gains' is uninitialized when used here [-Werror,-Wuninitialized] lpphy_papd_cal(dev, gains, 0, 1, 30); ^~~~~ drivers/net/wireless/broadcom/b43/phy_lp.c:1838:2: note: variable 'gains' is declared here struct lpphy_tx_gains gains, oldgains; ^ 1 error generated. However, this function is empty, and its arguments are never evaluated, so gcc in contrast does not warn here. Both compilers behave in a reasonable way as far as I can tell, so we should change the code to avoid the warning everywhere. We could just eliminate the lpphy_papd_cal() function entirely, given that it has had the TODO comment in it for 10 years now and is rather unlikely to ever get done. I'm doing a simpler change here, and just pass the 'oldgains' variable in that has been initialized, based on the guess that this is what was originally meant. Fixes: 2c0d6100 ("b43: LP-PHY: Begin implementing calibration & software RFKILL support") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Acked-by:
Larry Finger <Larry.Finger@lwfinger.net> Reviewed-by:
Nathan Chancellor <natechancellor@gmail.com> Signed-off-by:
-
Kangjie Lu authored
[ Upstream commit 46953f97 ] In case kmemdup fails, the fix sets conn_info->req_ie_len and conn_info->resp_ie_len to zero to avoid buffer overflows. Signed-off-by:
Kangjie Lu <kjlu@umn.edu> Acked-by:
Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by:
-
YueHaibing authored
[ Upstream commit 003b686a ] 'hostcmd' is alloced by kzalloc, should be freed before leaving from the error handling cases, otherwise it will cause mem leak. Fixes: 3935ccc1 ("mwifiex: add cfg80211 testmode support") Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
Kangjie Lu authored
[ Upstream commit 76597628 ] In case alloc_workqueue fails, the fix reports the error and returns to avoid NULL pointer dereference. Signed-off-by:
-
Nathan Chancellor authored
[ Upstream commit 6f9ca1d3 ] When building with -Wsometimes-uninitialized, Clang warns: drivers/iio/common/ssp_sensors/ssp_iio.c:95:6: warning: variable 'calculated_time' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized] While it isn't wrong, this will never be a problem because iio_push_to_buffers_with_timestamp only uses calculated_time on the same condition that it is assigned (when scan_timestamp is not zero). While iio_push_to_buffers_with_timestamp is marked as inline, Clang does inlining in the optimization stage, which happens after the semantic analysis phase (plus inline is merely a hint to the compiler). Fix this by just zero initializing calculated_time. Link: https://github.com/ClangBuiltLinux/linux/issues/394Signed-off-by:
Nick Desaulniers <ndesaulniers@google.com> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by:
-
Kangjie Lu authored
[ Upstream commit 536cc27d ] devm_regmap_init_i2c may fail and return NULL. The fix returns the error when it fails. Signed-off-by:
-
Lars-Peter Clausen authored
[ Upstream commit df1d80ae ] For devices from the SigmaDelta family we need to keep CS low when doing a conversion, since the device will use the MISO line as a interrupt to indicate that the conversion is complete. This is why the driver locks the SPI bus and when the SPI bus is locked keeps as long as a conversion is going on. The current implementation gets one small detail wrong though. CS is only de-asserted after the SPI bus is unlocked. This means it is possible for a different SPI device on the same bus to send a message which would be wrongfully be addressed to the SigmaDelta device as well. Make sure that the last SPI transfer that is done while holding the SPI bus lock de-asserts the CS signal. Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
Alexandru Ardelean <Alexandru.Ardelean@analog.com> Signed-off-by:
-
Kees Cook authored
[ Upstream commit 7c21383f ] The LLVM linker (ld.lld) defaults to removing local relocations, which causes KASLR boot failures. ld.bfd and ld.gold already handle this correctly. This adds the explicit instruction "--discard-none" during the link phase. There is no change in output for ld.bfd and ld.gold, but ld.lld now produces an image with all the needed relocations. Signed-off-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
Borislav Petkov <bp@suse.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: clang-built-linux@googlegroups.com Cc: x86-ml <x86@kernel.org> Link: https://lkml.kernel.org/r/20190404214027.GA7324@beast Link: https://github.com/ClangBuiltLinux/linux/issues/404Signed-off-by:
-
Wen Yang authored
[ Upstream commit 8d10dc28 ] The call to of_find_node_by_name returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage. Detected by coccinelle with the following warnings: ./drivers/cpufreq/pmac32-cpufreq.c:557:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 552, but without a corresponding object release within this function. ./drivers/cpufreq/pmac32-cpufreq.c:569:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 552, but without a corresponding object release within this function. ./drivers/cpufreq/pmac32-cpufreq.c:598:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 587, but without a corresponding object release within this function. Signed-off-by:
Wen Yang <wen.yang99@zte.com.cn> Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> Cc: Viresh Kumar <viresh.kumar@linaro.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: linux-pm@vger.kernel.org Cc: linuxppc-dev@lists.ozlabs.org Cc: linux-kernel@vger.kernel.org Signed-off-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
-
Wen Yang authored
[ Upstream commit a9acc26b ] The call to of_get_cpu_node returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage. Detected by coccinelle with the following warnings: ./drivers/cpufreq/pasemi-cpufreq.c:212:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 147, but without a corresponding object release within this function. ./drivers/cpufreq/pasemi-cpufreq.c:220:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 147, but without a corresponding object release within this function. Signed-off-by:
-
Wen Yang authored
[ Upstream commit 23329803 ] The call to of_get_cpu_node returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage. Detected by coccinelle with the following warnings: ./drivers/cpufreq/ppc_cbe_cpufreq.c:89:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 76, but without a corresponding object release within this function. ./drivers/cpufreq/ppc_cbe_cpufreq.c:89:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 76, but without a corresponding object release within this function. Signed-off-by:
-
Arnd Bergmann authored
[ Upstream commit e91012ee ] clang points out that the declaration of cio_irb does not match the definition exactly, it is missing the alignment attribute: ../drivers/s390/cio/cio.c:50:1: warning: section does not match previous declaration [-Wsection] DEFINE_PER_CPU_ALIGNED(struct irb, cio_irb); ^ ../include/linux/percpu-defs.h:150:2: note: expanded from macro 'DEFINE_PER_CPU_ALIGNED' DEFINE_PER_CPU_SECTION(type, name, PER_CPU_ALIGNED_SECTION) \ ^ ../include/linux/percpu-defs.h:93:9: note: expanded from macro 'DEFINE_PER_CPU_SECTION' extern __PCPU_ATTRS(sec) __typeof__(type) name; \ ^ ../include/linux/percpu-defs.h:49:26: note: expanded from macro '__PCPU_ATTRS' __percpu __attribute__((section(PER_CPU_BASE_SECTION sec))) \ ^ ../drivers/s390/cio/cio.h:118:1: note: previous attribute is here DECLARE_PER_CPU(struct irb, cio_irb); ^ ../include/linux/percpu-defs.h:111:2: note: expanded from macro 'DECLARE_PER_CPU' DECLARE_PER_CPU_SECTION(type, name, "") ^ ../include/linux/percpu-defs.h:87:9: note: expanded from macro 'DECLARE_PER_CPU_SECTION' extern __PCPU_ATTRS(sec) __typeof__(type) name ^ ../include/linux/percpu-defs.h:49:26: note: expanded from macro '__PCPU_ATTRS' __percpu __attribute__((section(PER_CPU_BASE_SECTION sec))) \ ^ Use DECLARE_PER_CPU_ALIGNED() here, to make the two match. Signed-off-by:
Sebastian Ott <sebott@linux.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Charles Keepax authored
[ Upstream commit 00053de5 ] Microphone detection provides the button detection features on the Arizona CODECs as such it will be running if the jack is currently inserted. If the driver is unbound whilst the jack is still inserted this will cause warnings from the regulator framework as the MICVDD regulator is put but was never disabled. Correct this by disabling microphone detection on driver removal and if the microphone detection was running disable the regulator and put the runtime reference that was currently held. Signed-off-by:
Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by:
Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by:
-
Ulf Hansson authored
[ Upstream commit dc351d4c ] The dev->power.direct_complete flag may become set in device_prepare() in case the device don't have any PM callbacks (dev->power.no_pm_callbacks is set). This leads to a broken behaviour, when there is child having wakeup enabled and relies on its parent to be used in the wakeup path. More precisely, when the direct complete path becomes selected for the child in __device_suspend(), the propagation of the dev->power.wakeup_path becomes skipped as well. Let's address this problem, by checking if the device is a part the wakeup path or has wakeup enabled, then prevent the direct complete path from being used. Reported-by:
Loic Pallardy <loic.pallardy@st.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> [ rjw: Comment cleanup ] Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Yinbo Zhu authored
[ Upstream commit 05cb6b2a ] eSDHC-A001: The data timeout counter (SYSCTL[DTOCV]) is not reliable for DTOCV values 0x4(2^17 SD clock), 0x8(2^21 SD clock), and 0xC(2^25 SD clock). The data timeout counter can count from 2^13–2^27, but for values 2^17, 2^21, and 2^25, the timeout counter counts for only 2^13 SD clocks. A-008358: The data timeout counter value loaded into the timeout counter is less than expected and can result into early timeout error in case of eSDHC data transactions. The table below shows the expected vs actual timeout period for different values of SYSCTL[DTOCV]: these two erratum has the same quirk to control it, and set SDHCI_QUIRK_RESET_AFTER_REQUEST to fix above issue. Signed-off-by:
Yinbo Zhu <yinbo.zhu@nxp.com> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
-
Yinbo Zhu authored
[ Upstream commit a46e4271 ] Software writing to the Transfer Type configuration register (system clock domain) can cause a setup/hold violation in the CRC flops (card clock domain), which can cause write accesses to be sent with corrupt CRC values. This issue occurs only for write preceded by read. this erratum is to fix this issue. Signed-off-by:
-
Kangjie Lu authored
[ Upstream commit 61102598 ] In case spi_sync_locked fails, the fix reports the error and returns the error code upstream. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Andrea Merello authored
[ Upstream commit 002ee28e ] pwrseq_emmc.c implements a HW reset procedure for eMMC chip by driving a GPIO line. It registers the .reset() cb on mmc_pwrseq_ops and it registers a system restart notification handler; both of them perform reset by unconditionally calling gpiod_set_value(). If the eMMC reset line is tied to a GPIO controller whose driver can sleep (i.e. I2C GPIO controller), then the kernel would spit warnings when trying to reset the eMMC chip by means of .reset() mmc_pwrseq_ops cb (that is exactly what I'm seeing during boot). Furthermore, on system reset we would gets to the system restart notification handler with disabled interrupts - local_irq_disable() is called in machine_restart() at least on ARM/ARM64 - and we would be in trouble when the GPIO driver tries to sleep (which indeed doesn't happen here, likely because in my case the machine specific code doesn't call do_kernel_restart(), I guess..). This patch fixes the .reset() cb to make use of gpiod_set_value_cansleep(), so that the eMMC gets reset on boot without complaints, while, since there isn't that much we can do, we avoid register the restart handler if the GPIO controller has a sleepy driver (and we spit a dev_notice() message to let people know).. This had been tested on a downstream 4.9 kernel with backported commit 83f37ee7ba33 ("mmc: pwrseq: Add reset callback to the struct mmc_pwrseq_ops") and commit ae60fb031cf2 ("mmc: core: Don't do eMMC HW reset when resuming the eMMC card"), because I couldn't boot my board otherwise. Maybe worth to RFT. Signed-off-by:
Andrea Merello <andrea.merello@gmail.com> Signed-off-by:
-
John Garry authored
[ Upstream commit d8649fc1 ] When we discover the PHY is empty in sas_rediscover_dev(), the PHY information (like negotiated linkrate) is not updated. As such, for a user examining sysfs for that PHY, they would see incorrect values: root@(none)$ cd /sys/class/sas_phy/phy-0:0:20 root@(none)$ more negotiated_linkrate 3.0 Gbit root@(none)$ echo 0 > enable root@(none)$ more negotiated_linkrate 3.0 Gbit So fix this, simply discover the PHY again, even though we know it's empty; in the above example, this gives us: root@(none)$ more negotiated_linkrate Phy disabled We must do this after unregistering the device associated with the PHY (in sas_unregister_devs_sas_addr()). Signed-off-by:
John Garry <john.garry@huawei.com> Signed-off-by:
-
Guenter Roeck authored
[ Upstream commit 73e6ff71 ] Super-IO accesses may fail on a system with no or unmapped LPC bus. Unable to handle kernel paging request at virtual address ffffffbffee0002e pgd = ffffffc1d68d4000 [ffffffbffee0002e] *pgd=0000000000000000, *pud=0000000000000000 Internal error: Oops: 94000046 [#1] PREEMPT SMP Modules linked in: f71805f(+) hwmon CPU: 3 PID: 1659 Comm: insmod Not tainted 4.5.0+ #88 Hardware name: linux,dummy-virt (DT) task: ffffffc1f6665400 ti: ffffffc1d6418000 task.ti: ffffffc1d6418000 PC is at f71805f_find+0x6c/0x358 [f71805f] Also, other drivers may attempt to access the LPC bus at the same time, resulting in undefined behavior. Use request_muxed_region() to ensure that IO access on the requested address space is supported, and to ensure that access by multiple drivers is synchronized. Fixes: e53004e2 ("hwmon: New f71805f driver") Reported-by:
Kefeng Wang <wangkefeng.wang@huawei.com> Reported-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Guenter Roeck authored
[ Upstream commit 755a9b0f ] Super-IO accesses may fail on a system with no or unmapped LPC bus. Also, other drivers may attempt to access the LPC bus at the same time, resulting in undefined behavior. Use request_muxed_region() to ensure that IO access on the requested address space is supported, and to ensure that access by multiple drivers is synchronized. Fixes: ba224e2c ("hwmon: New PC87427 hardware monitoring driver") Reported-by:
-
Guenter Roeck authored
[ Upstream commit 8c082675 ] Super-IO accesses may fail on a system with no or unmapped LPC bus. Also, other drivers may attempt to access the LPC bus at the same time, resulting in undefined behavior. Use request_muxed_region() to ensure that IO access on the requested address space is supported, and to ensure that access by multiple drivers is synchronized. Fixes: 8d5d45fb ("I2C: Move hwmon drivers (2/3)") Reported-by:
-
Guenter Roeck authored
[ Upstream commit d6410408 ] Super-IO accesses may fail on a system with no or unmapped LPC bus. Also, other drivers may attempt to access the LPC bus at the same time, resulting in undefined behavior. Use request_muxed_region() to ensure that IO access on the requested address space is supported, and to ensure that access by multiple drivers is synchronized. Fixes: 8d5d45fb ("I2C: Move hwmon drivers (2/3)") Reported-by:
-
Guenter Roeck authored
[ Upstream commit 14b97ba5 ] Super-IO accesses may fail on a system with no or unmapped LPC bus. Also, other drivers may attempt to access the LPC bus at the same time, resulting in undefined behavior. Use request_muxed_region() to ensure that IO access on the requested address space is supported, and to ensure that access by multiple drivers is synchronized. Fixes: 2219cd81 ("hwmon/vt1211: Add probing of alternate config index port") Signed-off-by:
-
Colin Ian King authored
[ Upstream commit a6d2a5a9 ] Currently if alloc_skb fails to allocate the skb a null skb is passed to t4_set_arp_err_handler and this ends up dereferencing the null skb. Avoid the NULL pointer dereference by checking for a NULL skb and returning early. Addresses-Coverity: ("Dereference null return") Fixes: b38a0ad8 ("RDMA/cxgb4: Set arp error handler for PASS_ACCEPT_RPL messages") Signed-off-by:
Colin Ian King <colin.king@canonical.com> Acked-by:
Potnuri Bharat Teja <bharat@chelsio.com> Signed-off-by:
Jason Gunthorpe <jgg@mellanox.com> Signed-off-by:
-
Vincenzo Frascino authored
[ Upstream commit 81fb8736 ] clock_getres() in the vDSO library has to preserve the same behaviour of posix_get_hrtimer_res(). In particular, posix_get_hrtimer_res() does: sec = 0; ns = hrtimer_resolution; where 'hrtimer_resolution' depends on whether or not high resolution timers are enabled, which is a runtime decision. The vDSO incorrectly returns the constant CLOCK_REALTIME_RES. Fix this by exposing 'hrtimer_resolution' in the vDSO datapage and returning that instead. Reviewed-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
Vincenzo Frascino <vincenzo.frascino@arm.com> [will: Use WRITE_ONCE(), move adr off COARSE path, renumber labels, use 'w' reg] Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Nicholas Nunley authored
[ Upstream commit bfb0ebed ] Modifying the VLAN stripping options when a port VLAN is configured will break traffic for the VSI, and conceptually doesn't make sense, so don't allow this. Signed-off-by:
Nicholas Nunley <nicholas.d.nunley@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
Thomas Gleixner authored
[ Upstream commit 7dbcf2b0 ] Commit 37fe6a42 ("x86: Check stack overflow in detail") added a broad check for the full exception stack area, i.e. it considers the full exception stack area as valid. That's wrong in two aspects: 1) It does not check the individual areas one by one 2) #DF, NMI and #MCE are not enabling interrupts which means that a regular device interrupt cannot happen in their context. In fact if a device interrupt hits one of those IST stacks that's a bug because some code path enabled interrupts while handling the exception. Limit the check to the #DB stack and consider all other IST stacks as 'overflow' or invalid. Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Alan Stern authored
[ Upstream commit 381419fa ] The SCSI core does not like to have devices or hosts unregistered while error recovery is in progress. Trying to do so can lead to self-deadlock: Part of the removal code tries to obtain a lock already held by the error handler. This can cause problems for the usb-storage and uas drivers, because their error handler routines perform a USB reset, and if the reset fails then the USB core automatically goes on to unbind all drivers from the device's interfaces -- all while still in the context of the SCSI error handler. As it turns out, practically all the scenarios leading to a USB reset failure end up causing a device disconnect (the main error pathway in usb_reset_and_verify_device(), at the end of the routine, calls hub_port_logical_disconnect() before returning). As a result, the hub_wq thread will soon become aware of the problem and will unbind all the device's drivers in its own context, not in the error-handler's context. This means that usb_reset_device() does not need to call usb_unbind_and_rebind_marked_interfaces() in cases where usb_reset_and_verify_device() has returned an error, because hub_wq will take care of everything anyway. This particular problem was observed in somewhat artificial circumstances, by using usbfs to tell a hub to power-down a port connected to a USB-3 mass storage device using the UAS protocol. With the port turned off, the currently executing command timed out and the error handler started running. The USB reset naturally failed, because the hub port was off, and the error handler deadlocked as described above. Not carrying out the call to usb_unbind_and_rebind_marked_interfaces() fixes this issue. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Kento Kobayashi <Kento.A.Kobayashi@sony.com> Tested-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Konstantin Khlebnikov authored
[ Upstream commit 5b61d50a ] Bit shift in scale_load() could overflow shares. This patch saturates it to MAX_SHARES like following sched_group_set_shares(). Example: # echo 9223372036854776832 > cpu.shares # cat cpu.shares Before patch: 1024 After pattch: 262144 Signed-off-by:
Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Acked-by:
Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/155125501891.293431.3345233332801109696.stgit@buzzSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Konstantin Khlebnikov authored
[ Upstream commit 1a8b4540 ] Large values could overflow u64 and pass following sanity checks. # echo 18446744073750000 > cpu.cfs_period_us # cat cpu.cfs_period_us 40448 # echo 18446744073750000 > cpu.cfs_quota_us # cat cpu.cfs_quota_us 40448 After this patch they will fail with -EINVAL. Signed-off-by:
-
Nathan Lynch authored
[ Upstream commit 2d4d9b30 ] When booted with "topology_updates=no", or when "off" is written to /proc/powerpc/topology_updates, NUMA reassignments are inhibited for PRRN and VPHN events. However, migration and suspend unconditionally re-enable reassignments via start_topology_update(). This is incoherent. Check the topology_updates_enabled flag in start/stop_topology_update() so that callers of those APIs need not be aware of whether reassignments are enabled. This allows the administrative decision on reassignments to remain in force across migrations and suspensions. Signed-off-by:
Nathan Lynch <nathanl@linux.ibm.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit c1ced46c ] The ctrl_check_input() function is called from pvr2_ctrl_range_check(). It's supposed to validate user supplied input and return true or false depending on whether the input is valid or not. The problem is that negative shifts or shifts greater than 31 are undefined in C. In practice with GCC they result in shift wrapping so this function returns true for some inputs which are not valid and this could result in a buffer overflow: drivers/media/usb/pvrusb2/pvrusb2-ctrl.c:205 pvr2_ctrl_get_valname() warn: uncapped user index 'names[val]' The cptr->hdw->input_allowed_mask mask is configured in pvr2_hdw_create() and the highest valid bit is BIT(4). Fixes: 7fb20fa3 ("V4L/DVB (7299): pvrusb2: Improve logic which handles input choice availability") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by:
-
Shuah Khan authored
[ Upstream commit 898bc40b ] Fix au0828_analog_stream_enable() to check if device is in the right state first. When unbind happens while bind is in progress, usbdev pointer could be invalid in au0828_analog_stream_enable() and a call to usb_ifnum_to_if() will result in the null pointer dereference. This problem is found with the new media_dev_allocator.sh test. kernel: [ 590.359623] BUG: unable to handle kernel NULL pointer dereference at 00000000000004e8 kernel: [ 590.359627] #PF error: [normal kernel read fault] kernel: [ 590.359629] PGD 0 P4D 0 kernel: [ 590.359632] Oops: 0000 [#1] SMP PTI kernel: [ 590.359634] CPU: 3 PID: 1458 Comm: v4l_id Not tainted 5.1.0-rc2+ #30 kernel: [ 590.359636] Hardware name: Dell Inc. OptiPlex 7 90/0HY9JP, BIOS A18 09/24/2013 kernel: [ 590.359641] RIP: 0010:usb_ifnum_to_if+0x6/0x60 kernel: [ 590.359643] Code: 5d 41 5e 41 5f 5d c3 48 83 c4 10 b8 fa ff ff ff 5b 41 5c 41 5d 41 5e 41 5f 5d c3 b8 fa ff ff ff c3 0f 1f 00 6 6 66 66 66 90 55 <48> 8b 97 e8 04 00 00 48 89 e5 48 85 d2 74 41 0f b6 4a 04 84 c 9 74 kernel: [ 590.359645] RSP: 0018:ffffad3cc3c1fc00 EFLAGS: 00010246 kernel: [ 590.359646] RAX: 0000000000000000 RBX: ffff8ded b1f3c000 RCX: 1f377e4500000000 kernel: [ 590.359648] RDX: ffff8dedfa3a6b50 RSI: 00000000 00000000 RDI: 0000000000000000 kernel: [ 590.359649] RBP: ffffad3cc3c1fc28 R08: 00000000 8574acc2 R09: ffff8dedfa3a6b50 kernel: [ 590.359650] R10: 0000000000000001 R11: 00000000 00000000 R12: 0000000000000000 kernel: [ 590.359652] R13: ffff8dedb1f3f0f0 R14: ffffffff adcf7ec0 R15: 0000000000000000 kernel: [ 590.359654] FS: 00007f7917198540(0000) GS:ffff 8dee258c0000(0000) knlGS:0000000000000000 kernel: [ 590.359655] CS: 0010 DS: 0000 ES: 0000 CR0: 00 00000080050033 kernel: [ 590.359657] CR2: 00000000000004e8 CR3: 00000001 a388e002 CR4: 00000000000606e0 kernel: [ 590.359658] Call Trace: kernel: [ 590.359664] ? au0828_analog_stream_enable+0x2c/0x180 kernel: [ 590.359666] au0828_v4l2_open+0xa4/0x110 kernel: [ 590.359670] v4l2_open+0x8b/0x120 kernel: [ 590.359674] chrdev_open+0xa6/0x1c0 kernel: [ 590.359676] ? cdev_put.part.3+0x20/0x20 kernel: [ 590.359678] do_dentry_open+0x1f6/0x360 kernel: [ 590.359681] vfs_open+0x2f/0x40 kernel: [ 590.359684] path_openat+0x299/0xc20 kernel: [ 590.359688] do_filp_open+0x9b/0x110 kernel: [ 590.359695] ? _raw_spin_unlock+0x27/0x40 kernel: [ 590.359697] ? __alloc_fd+0xb2/0x160 kernel: [ 590.359700] do_sys_open+0x1ba/0x260 kernel: [ 590.359702] ? do_sys_open+0x1ba/0x260 kernel: [ 590.359712] __x64_sys_openat+0x20/0x30 kernel: [ 590.359715] do_syscall_64+0x5a/0x120 kernel: [ 590.359718] entry_SYSCALL_64_after_hwframe+0x44/0xa9 Signed-off-by:
Shuah Khan <shuah@kernel.org> Signed-off-by:
-
Wenwen Wang authored
[ Upstream commit 70c4cf17 ] In audit_rule_change(), audit_data_to_entry() is firstly invoked to translate the payload data to the kernel's rule representation. In audit_data_to_entry(), depending on the audit field type, an audit tree may be created in audit_make_tree(), which eventually invokes kmalloc() to allocate the tree. Since this tree is a temporary tree, it will be then freed in the following execution, e.g., audit_add_rule() if the message type is AUDIT_ADD_RULE or audit_del_rule() if the message type is AUDIT_DEL_RULE. However, if the message type is neither AUDIT_ADD_RULE nor AUDIT_DEL_RULE, i.e., the default case of the switch statement, this temporary tree is not freed. To fix this issue, only allocate the tree when the type is AUDIT_ADD_RULE or AUDIT_DEL_RULE. Signed-off-by:
Wenwen Wang <wang6495@umn.edu> Reviewed-by:
Richard Guy Briggs <rgb@redhat.com> Signed-off-by:
Paul Moore <paul@paul-moore.com> Signed-off-by:
-
