Add a UART driver for the new Broadcom 8250 based STB UART. The new
UART is backward compatible with the standard 8250, but has some
additional features. The new features include a high accuracy baud
rate clock system and DMA support.

The driver will use the new optional BAUD MUX clock to select the best
one of the four master clocks (81MHz, 108MHz, 64MHz and 48MHz) to feed
the baud rate selection logic for any requested baud rate.  This allows
for more accurate BAUD rates when high speed baud rates are selected.

The driver will use the new UART DMA hardware if the UART DMA registers
are specified in Device Tree "reg" property.

The driver also sets the UPSTAT_AUTOCTS flag when hardware flow control
is enabled. This flag is needed for UARTs that don't assert a CTS
changed interrupt when CTS changes and AFE (Hardware Flow Control) is
enabled.

The driver also contains a workaround for a bug in the Synopsis 8250
core. The problem is that at high baud rates, the RX partial FIFO
timeout interrupt can occur but there is no RX data (DR not set in
the LSR register). In this case the driver will not read the Receive
Buffer Register, which clears the interrupt, and the system will get
continuous UART interrupts until the next RX character arrives. The
fix originally suggested by Synopsis was to read the Receive Buffer
Register and discard the character when the DR bit in the LSR was
not set, to clear the interrupt. The problem was that occasionally
a character would arrive just after the DR bit check and a valid
character would be discarded. The fix that was added will clear
receive interrupts to stop the interrupt, deassert RTS to insure
that no new data can arrive, wait for 1.5 character times for the
sender to react to RTS and then check for data and either do a dummy
read or a valid read. Debugfs error counters were also added and were
used to help create test software that would cause the error condition.
The counters can be found at:
/sys/kernel/debug/bcm7271-uart/<device-name>/stats

This also includes a few fixes for build warnings reported by
the kernel test robot.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20210325185256.16156-3-alcooperx@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add DT bindings for the Broadcom 8250 based UART driver. This
UART is based on an 8250 but adds additional functionality. The
additional features include the ability to use DMA for transfers and
a baud rate clock system that is more accurate at high baud rates.
This UART is backward compatible with the standard 8250 UART.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20210325185256.16156-2-alcooperx@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s/spurrious/spurious/
s/worse/worst/
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Link: https://lore.kernel.org/r/20210314062716.28539-1-unixbhaskar@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Kernel documentation validator is not happy:

.../keyboard.c:2195: warning: expecting prototype for vt_get_shiftstate(). Prototype was for vt_get_shift_state() instead

This is due to typo, fix it here.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210303083229.75784-1-andriy.shevchenko@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This commit adds dt-binding documentation of uart for Mediatek MT8195 SoC
Platform.
Signed-off-by: Seiya Wang <seiya.wang@mediatek.com>
Link: https://lore.kernel.org/r/20210319023427.16711-4-seiya.wang@mediatek.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Force-threaded interrupt handlers used to run with interrupts enabled,
something which could lead to deadlocks in case a threaded handler
shared a lock with code running in hard interrupt context (e.g. timer
callbacks) and did not explicitly disable interrupts.

This was specifically the case for serial drivers that take the port
lock in their console write path as printk can be called from hard
interrupt context also with forced threading ("threadirqs").

Since commit 81e2073c ("genirq: Disable interrupts for force
threaded handlers") interrupt handlers always run with interrupts
disabled on non-RT so that drivers no longer need to do handle this.

Drop the now obsolete workaround added by commit 33f16855 ("tty:
serial: imx: fix potential deadlock").

Cc: Sam Nobs <samuel.nobs@taitradio.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322111036.31966-1-johan@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix the build error with CONFIG_DEBUG_FS is not set:

drivers/tty/serial/pch_uart.c: In function 'pch_uart_init_port':
drivers/tty/serial/pch_uart.c:1815:9: error: 'port_regs_ops' undeclared (first use in this function)
 1815 |        &port_regs_ops);
      |         ^~~~~~~~~~~~~

This commit get rid of the CONFIG_PM_SLEEP ifdefery to
fix the build error.

Fixes: 1f8a51ee3242 ("tty: serial: pch_uart.c: remove debugfs dentry pointer")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210322122601.2980258-1-weiyongjun1@huawei.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add EXTI lines to the following UART nodes which are used for
wakeup from CStop.
- EXTI line 26 to USART1
- EXTI line 27 to USART2
- EXTI line 28 to USART3
- EXTI line 29 to USART6
- EXTI line 30 to UART4
- EXTI line 31 to UART5
- EXTI line 32 to UART7
- EXTI line 33 to UART8
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210319184253.5841-6-erwan.leray@foss.st.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The wakeup specific IRQ management is no more needed to wake up the stm32
plaform. A relationship has been established between the EXTI and
the EVENT IRQ, just need to declare the EXTI interrupt instead of the
UART event IRQ.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210319184253.5841-5-erwan.leray@foss.st.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add following usart instances exti direct event support (used for UART wake
up).
- exti 26 (USART1) is mapped to GIC 37
- exti 27 (USART2) is mapped to GIC 38
- exti 28 (USART3) is mapped to GIC 39
- exti 29 (USART6) is mapped to GIC 71
- exti 31 (UART5) is mapped to GIC 53
- exti 32 (UART7) is mapped to GIC 82
- exti 33 (UART8) is mapped to GIC 83
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210319184253.5841-4-erwan.leray@foss.st.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove useless call to stm32_usart_serial_en_wakeup() routine in suspend
callback. When called with "false" argument, this routine is clearing UESM
and WUFIE bits if usart is not wakeup source. Those bits are already
cleared in set_termios(), and then in serial_resume() callback when usart
is wakeup source.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210319184253.5841-3-erwan.leray@foss.st.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Rework wakeup management by activating uart as wakeup source when usart
device OR its tty virtual device parent is wakeup source.

This patch aim to avoid potential misalignment between serial and tty
wakeup flags.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210319184253.5841-2-erwan.leray@foss.st.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 973c096f ("vgacon: remove software scrollback support")
removed all uses of vga_init_done, so let's get rid of it entirely.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20210215170837.1599706-1-steve@sk2.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

wheter -> whether
Signed-off-by: Wang Qing <wangqing@vivo.com>
Link: https://lore.kernel.org/r/1615345622-2015-1-git-send-email-wangqing@vivo.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Zero-length and one-element arrays are deprecated, see
Documentation/process/deprecated.rst
Flexible-array members should be used instead.

Generated by: scripts/coccinelle/misc/flexible_array.cocci

Fixes: 10d8b34a ("serial: max310x: Driver rework")
CC: Denis Efremov <efremov@linux.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@inria.fr>
Link: https://lore.kernel.org/r/alpine.DEB.2.22.394.2103091516020.2892@hadrienSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

platform_get_irq() has already checked and printed the return value,
the printing here is nothing special, it is not necessary at all.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Link: https://lore.kernel.org/r/1615621707-2330-1-git-send-email-wangqing@vivo.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since interrupt handler is called with disabled local interrupts, there
is no need to use the spinlock primitives disabling interrupts as well.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210315181212.113217-1-krzysztof.kozlowski@canonical.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Resolves a merge issue with:
	drivers/tty/hvc/hvcs.c
and we want the tty/serial fixes from 5.12-rc3 in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Doing a

	prctl(PR_SET_MM, PR_SET_MM_AUXV, addr, 1);

will copy 1 byte from userspace to (quite big) on-stack array
and then stash everything to mm->saved_auxv.
AT_NULL terminator will be inserted at the very end.

/proc/*/auxv handler will find that AT_NULL terminator
and copy original stack contents to userspace.

This devious scheme requires CAP_SYS_RESOURCE.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull irq fixes from Thomas Gleixner:
 "A set of irqchip updates:

   - Make the GENERIC_IRQ_MULTI_HANDLER configuration correct

   - Add a missing DT compatible string for the Ingenic driver

   - Remove the pointless debugfs_file pointer from struct irqdomain"

* tag 'irq-urgent-2021-03-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/ingenic: Add support for the JZ4760
  dt-bindings/irq: Add compatible string for the JZ4760B
  irqchip: Do not blindly select CONFIG_GENERIC_IRQ_MULTI_HANDLER
  ARM: ep93xx: Select GENERIC_IRQ_MULTI_HANDLER directly
  irqdomain: Remove debugfs_file from struct irq_domain

Pull timer fix from Thomas Gleixner:
 "A single fix in for hrtimers to prevent an interrupt storm caused by
  the lack of reevaluation of the timers which expire in softirq context
  under certain circumstances, e.g. when the clock was set"

* tag 'timers-urgent-2021-03-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  hrtimer: Update softirq_expires_next correctly after __hrtimer_get_next_event()

Pull scheduler fixes from Thomas Gleixner:
 "A set of scheduler updates:

   - Prevent a NULL pointer dereference in the migration_stop_cpu()
     mechanims

   - Prevent self concurrency of affine_move_task()

   - Small fixes and cleanups related to task migration/affinity setting

   - Ensure that sync_runqueues_membarrier_state() is invoked on the
     current CPU when it is in the cpu mask"

* tag 'sched-urgent-2021-03-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/membarrier: fix missing local execution of ipi_sync_rq_state()
  sched: Simplify set_affinity_pending refcounts
  sched: Fix affine_move_task() self-concurrency
  sched: Optimize migration_cpu_stop()
  sched: Collate affine_move_task() stoppers
  sched: Simplify migration_cpu_stop()
  sched: Fix migration_cpu_stop() requeueing

Pull objtool fix from Thomas Gleixner:
 "A single objtool fix to handle the PUSHF/POPF validation correctly for
  the paravirt changes which modified arch_local_irq_restore not to use
  popf"

* tag 'objtool-urgent-2021-03-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  objtool,x86: Fix uaccess PUSHF/POPF validation

Pull locking fixes from Thomas Gleixner:
 "A couple of locking fixes:

   - A fix for the static_call mechanism so it handles unaligned
     addresses correctly.

   - Make u64_stats_init() a macro so every instance gets a seperate
     lockdep key.

   - Make seqcount_latch_init() a macro as well to preserve the static
     variable which is used for the lockdep key"

* tag 'locking-urgent-2021-03-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  seqlock,lockdep: Fix seqcount_latch_init()
  u64_stats,lockdep: Fix u64_stats_init() vs lockdep
  static_call: Fix the module key fixup

Pull perf fixes from Borislav Petkov:

 - Make sure PMU internal buffers are flushed for per-CPU events too and
   properly handle PID/TID for large PEBS.

 - Handle the case properly when there's no PMU and therefore return an
   empty list of perf MSRs for VMX to switch instead of reading random
   garbage from the stack.

* tag 'perf_urgent_for_v5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/perf: Use RET0 as default for guest_get_msrs to handle "no PMU" case
  perf/x86/intel: Set PERF_ATTACH_SCHED_CB for large PEBS and LBR
  perf/core: Flush PMU internal buffers for per-CPU events

Pull EFI fix from Ard Biesheuvel via Borislav Petkov:
 "Fix an oversight in the handling of EFI_RT_PROPERTIES_TABLE, which was
  added v5.10, but failed to take the SetVirtualAddressMap() RT service
  into account"

* tag 'efi-urgent-for-v5.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  efi: stub: omit SetVirtualAddressMap() if marked unsupported in RT_PROP table

Pull x86 fixes from Borislav Petkov:

 - A couple of SEV-ES fixes and robustifications: verify usermode stack
   pointer in NMI is not coming from the syscall gap, correctly track
   IRQ states in the #VC handler and access user insn bytes atomically
   in same handler as latter cannot sleep.

 - Balance 32-bit fast syscall exit path to do the proper work on exit
   and thus not confuse audit and ptrace frameworks.

 - Two fixes for the ORC unwinder going "off the rails" into KASAN
   redzones and when ORC data is missing.

* tag 'x86_urgent_for_v5.12_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/sev-es: Use __copy_from_user_inatomic()
  x86/sev-es: Correctly track IRQ states in runtime #VC handler
  x86/sev-es: Check regs->sp is trusted before adjusting #VC IST stack
  x86/sev-es: Introduce ip_within_syscall_gap() helper
  x86/entry: Fix entry/exit mismatch on failed fast 32-bit syscalls
  x86/unwind/orc: Silence warnings caused by missing ORC data
  x86/unwind/orc: Disable KASAN checking in the ORC unwinder, part 2

Pull powerpc fixes from Michael Ellerman:
 "Some more powerpc fixes for 5.12:

   - Fix wrong instruction encoding for lis in ppc_function_entry(),
     which could potentially lead to missed kprobes.

   - Fix SET_FULL_REGS on 32-bit and 64e, which prevented ptrace of
     non-volatile GPRs immediately after exec.

   - Clean up a missed SRR specifier in the recent interrupt rework.

   - Don't treat unrecoverable_exception() as an interrupt handler, it's
     called from other handlers so shouldn't do the interrupt entry/exit
     accounting itself.

   - Fix build errors caused by missing declarations for
     [en/dis]able_kernel_vsx().

  Thanks to Christophe Leroy, Daniel Axtens, Geert Uytterhoeven, Jiri
  Olsa, Naveen N. Rao, and Nicholas Piggin"

* tag 'powerpc-5.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/traps: unrecoverable_exception() is not an interrupt handler
  powerpc: Fix missing declaration of [en/dis]able_kernel_vsx()
  powerpc/64s/exception: Clean up a missed SRR specifier
  powerpc: Fix inverted SET_FULL_REGS bitop
  powerpc/64s: Use symbolic macros for function entry encoding
  powerpc/64s: Fix instruction encoding for lis in ppc_function_entry()

Pull KVM fixes from Paolo Bonzini:
 "More fixes for ARM and x86"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: LAPIC: Advancing the timer expiration on guest initiated write
  KVM: x86/mmu: Skip !MMU-present SPTEs when removing SP in exclusive mode
  KVM: kvmclock: Fix vCPUs > 64 can't be online/hotpluged
  kvm: x86: annotate RCU pointers
  KVM: arm64: Fix exclusive limit for IPA size
  KVM: arm64: Reject VM creation when the default IPA size is unsupported
  KVM: arm64: Ensure I-cache isolation between vcpus of a same VM
  KVM: arm64: Don't use cbz/adr with external symbols
  KVM: arm64: Fix range alignment when walking page tables
  KVM: arm64: Workaround firmware wrongly advertising GICv2-on-v3 compatibility
  KVM: arm64: Rename __vgic_v3_get_ich_vtr_el2() to __vgic_v3_get_gic_config()
  KVM: arm64: Don't access PMSELR_EL0/PMUSERENR_EL0 when no PMU is available
  KVM: arm64: Turn kvm_arm_support_pmu_v3() into a static key
  KVM: arm64: Fix nVHE hyp panic host context restore
  KVM: arm64: Avoid corrupting vCPU context register in guest exit
  KVM: arm64: nvhe: Save the SPE context early
  kvm: x86: use NULL instead of using plain integer as pointer
  KVM: SVM: Connect 'npt' module param to KVM's internal 'npt_enabled'
  KVM: x86: Ensure deadline timer has truly expired before posting its IRQ

Merge misc fixes from Andrew Morton:
 "28 patches.

  Subsystems affected by this series: mm (memblock, pagealloc, hugetlb,
  highmem, kfence, oom-kill, madvise, kasan, userfaultfd, memcg, and
  zram), core-kernel, kconfig, fork, binfmt, MAINTAINERS, kbuild, and
  ia64"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (28 commits)
  zram: fix broken page writeback
  zram: fix return value on writeback_store
  mm/memcg: set memcg when splitting page
  mm/memcg: rename mem_cgroup_split_huge_fixup to split_page_memcg and add nr_pages argument
  ia64: fix ptrace(PTRACE_SYSCALL_INFO_EXIT) sign
  ia64: fix ia64_syscall_get_set_arguments() for break-based syscalls
  mm/userfaultfd: fix memory corruption due to writeprotect
  kasan: fix KASAN_STACK dependency for HW_TAGS
  kasan, mm: fix crash with HW_TAGS and DEBUG_PAGEALLOC
  mm/madvise: replace ptrace attach requirement for process_madvise
  include/linux/sched/mm.h: use rcu_dereference in in_vfork()
  kfence: fix reports if constant function prefixes exist
  kfence, slab: fix cache_alloc_debugcheck_after() for bulk allocations
  kfence: fix printk format for ptrdiff_t
  linux/compiler-clang.h: define HAVE_BUILTIN_BSWAP*
  MAINTAINERS: exclude uapi directories in API/ABI section
  binfmt_misc: fix possible deadlock in bm_register_write
  mm/highmem.c: fix zero_user_segments() with start > end
  hugetlb: do early cow when page pinned on src mm
  mm: use is_cow_mapping() across tree where proper
  ...

Merge tag 'irqchip-fixes-5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent

Pull irqchip fixes from Marc Zyngier:

  - More compatible strings for the Ingenic irqchip (introducing the
    JZ4760B SoC)
  - Select GENERIC_IRQ_MULTI_HANDLER on the ARM ep93xx platform
  - Drop all GENERIC_IRQ_MULTI_HANDLER selections from the irqchip
    Kconfig, now relying on the architecture to get it right
  - Drop the debugfs_file field from struct irq_domain, now that
    debugfs can track things on its own

Pull char/misc driver fixes from Greg KH:
 "Here are some small misc/char driver fixes to resolve some reported
  problems:

   - habanalabs driver fixes

   - Acrn build fixes (reported many times)

   - pvpanic module table export fix

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'char-misc-5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  misc/pvpanic: Export module FDT device table
  misc: fastrpc: restrict user apps from sending kernel RPC messages
  virt: acrn: Correct type casting of argument of copy_from_user()
  virt: acrn: Use EPOLLIN instead of POLLIN
  virt: acrn: Use vfs_poll() instead of f_op->poll()
  virt: acrn: Make remove_cpu sysfs invisible with !CONFIG_HOTPLUG_CPU
  cpu/hotplug: Fix build error of using {add,remove}_cpu() with !CONFIG_SMP
  habanalabs: fix debugfs address translation
  habanalabs: Disable file operations after device is removed
  habanalabs: Call put_pid() when releasing control device
  drivers: habanalabs: remove unused dentry pointer for debugfs files
  habanalabs: mark hl_eq_inc_ptr() as static

Pull staging driver fixes from Greg KH:
 "Here are some small staging driver fixes for reported problems. They
  include:

   - wfx header file cleanup patch reverted as it could cause problems

   - comedi driver endian fixes

   - buffer overflow problems for staging wifi drivers

   - build dependency issue for rtl8192e driver

  All have been in linux-next for a while with no reported problems"

* tag 'staging-5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (23 commits)
  Revert "staging: wfx: remove unused included header files"
  staging: rtl8188eu: prevent ->ssid overflow in rtw_wx_set_scan()
  staging: rtl8188eu: fix potential memory corruption in rtw_check_beacon_data()
  staging: rtl8192u: fix ->ssid overflow in r8192_wx_set_scan()
  staging: comedi: pcl726: Use 16-bit 0 for interrupt data
  staging: comedi: ni_65xx: Use 16-bit 0 for interrupt data
  staging: comedi: ni_6527: Use 16-bit 0 for interrupt data
  staging: comedi: comedi_parport: Use 16-bit 0 for interrupt data
  staging: comedi: amplc_pc236_common: Use 16-bit 0 for interrupt data
  staging: comedi: pcl818: Fix endian problem for AI command data
  staging: comedi: pcl711: Fix endian problem for AI command data
  staging: comedi: me4000: Fix endian problem for AI command data
  staging: comedi: dmm32at: Fix endian problem for AI command data
  staging: comedi: das800: Fix endian problem for AI command data
  staging: comedi: das6402: Fix endian problem for AI command data
  staging: comedi: adv_pci1710: Fix endian problem for AI command data
  staging: comedi: addi_apci_1500: Fix endian problem for command sample
  staging: comedi: addi_apci_1032: Fix endian problem for COS sample
  staging: ks7010: prevent buffer overflow in ks_wlan_set_scan()
  staging: rtl8712: Fix possible buffer overflow in r8712_sitesurvey_cmd
  ...

Pull tty/serial fixes from Greg KH:
 "Here are some small tty and serial driver fixes to resolve some
  reported problems:

   - led tty trigger fixes based on review and were acked by the led
     maintainer

   - revert a max310x serial driver patch as it was causing problems

   - revert a pty change as it was also causing problems

  All of these have been in linux-next for a while with no reported
  problems"

* tag 'tty-5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  Revert "drivers:tty:pty: Fix a race causing data loss on close"
  Revert "serial: max310x: rework RX interrupt handling"
  leds: trigger/tty: Use led_set_brightness_sync() from workqueue
  leds: trigger: Fix error path to not unlock the unlocked mutex

Pull USB fixes from Greg KH:
 "Here are a small number of USB fixes for 5.12-rc3 to resolve a bunch
  of reported issues:

   - usbip fixups for issues found by syzbot

   - xhci driver fixes and quirk additions

   - gadget driver fixes

   - dwc3 QCOM driver fix

   - usb-serial new ids and fixes

   - usblp fix for a long-time issue

   - cdc-acm quirk addition

   - other tiny fixes for reported problems

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'usb-5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
  xhci: Fix repeated xhci wake after suspend due to uncleared internal wake state
  usb: xhci: Fix ASMedia ASM1042A and ASM3242 DMA addressing
  xhci: Improve detection of device initiated wake signal.
  usb: xhci: do not perform Soft Retry for some xHCI hosts
  usbip: fix vudc usbip_sockfd_store races leading to gpf
  usbip: fix vhci_hcd attach_store() races leading to gpf
  usbip: fix stub_dev usbip_sockfd_store() races leading to gpf
  usbip: fix vudc to check for stream socket
  usbip: fix vhci_hcd to check for stream socket
  usbip: fix stub_dev to check for stream socket
  usb: dwc3: qcom: Add missing DWC3 OF node refcount decrement
  USB: usblp: fix a hang in poll() if disconnected
  USB: gadget: udc: s3c2410_udc: fix return value check in s3c2410_udc_probe()
  usb: renesas_usbhs: Clear PIPECFG for re-enabling pipe with other EPNUM
  usb: dwc3: qcom: Honor wakeup enabled/disabled state
  usb: gadget: f_uac1: stop playback on function disable
  usb: gadget: f_uac2: always increase endpoint max_packet_size by one audio slot
  USB: gadget: u_ether: Fix a configfs return code
  usb: dwc3: qcom: add ACPI device id for sc8180x
  Goodix Fingerprint device is not a modem
  ...

Pull erofs fix from Gao Xiang:
 "Fix an urgent regression introduced by commit baa2c7c9 ("block:
  set .bi_max_vecs as actual allocated vector number"), which could
  cause unexpected hung since linux 5.12-rc1.

  Resolve it by avoiding using bio->bi_max_vecs completely"

* tag 'erofs-for-5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
  erofs: fix bio->bi_max_vecs behavior change

Merge tag 'kbuild-fixes-v5.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - avoid 'make image_name' invoking syncconfig

 - fix a couple of bugs in scripts/dummy-tools

 - fix LLD_VENDOR and locale issues in scripts/ld-version.sh

 - rebuild GCC plugins when the compiler is upgraded

 - allow LTO to be enabled with KASAN_HW_TAGS

 - allow LTO to be enabled without LLVM=1

* tag 'kbuild-fixes-v5.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: fix ld-version.sh to not be affected by locale
  kbuild: remove meaningless parameter to $(call if_changed_rule,dtc)
  kbuild: remove LLVM=1 test from HAS_LTO_CLANG
  kbuild: remove unneeded -O option to dtc
  kbuild: dummy-tools: adjust to scripts/cc-version.sh
  kbuild: Allow LTO to be selected with KASAN_HW_TAGS
  kbuild: dummy-tools: support MPROFILE_KERNEL checks for ppc
  kbuild: rebuild GCC plugins when the compiler is upgraded
  kbuild: Fix ld-version.sh script if LLD was built with LLD_VENDOR
  kbuild: dummy-tools: fix inverted tests for gcc
  kbuild: add image_name to no-sync-config-targets

commit 0d835962 ("zram: support page writeback") introduced two
problems.  It overwrites writeback_store's return value as kstrtol's
return value, which makes return value zero so user could see zero as
return value of write syscall even though it wrote data successfully.

It also breaks index value in the loop in that it doesn't increase the
index any longer.  It means it can write only first starting block index
so user couldn't write all idle pages in the zram so lose memory saving
chance.

This patch fixes those issues.

Link: https://lkml.kernel.org/r/20210312173949.2197662-2-minchan@kernel.org
Fixes: 0d835962("zram: support page writeback")
Signed-off-by: Minchan Kim <minchan@kernel.org>
Reported-by: Amos Bianchi <amosbianchi@google.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: John Dias <joaodias@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

writeback_store's return value is overwritten by submit_bio_wait's return
value.  Thus, writeback_store will return zero since there was no IO
error.  In the end, write syscall from userspace will see the zero as
return value, which could make the process stall to keep trying the write
until it will succeed.

Link: https://lkml.kernel.org/r/20210312173949.2197662-1-minchan@kernel.org
Fixes: 3b82a051("drivers/block/zram/zram_drv.c: fix error return codes not being returned in writeback_store")
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: John Dias <joaodias@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>