The "phyctrl_frqsel" is described in the Arasan datasheet [1] as "the
frequency range of DLL operation".  Although the Rockchip variant of
this PHY has different ranges than the reference Arasan PHY it appears
as if the functionality is similar.  We should set this phyctrl field
properly.

Note: as per Rockchip engineers, apparently the "phyctrl_frqsel" is
actually only useful in HS200 / HS400 modes even though the DLL itself
it used for some purposes in all modes.  See the discussion in the
earlier change in this series: ("mmc: sdhci-of-arasan: Always power the
PHY off/on when clock changes").  In any case, it shouldn't hurt to set
this always.

Note that this change should allow boards to run at HS200 / HS400 speed
modes while running at 100 MHz or 150 MHz.  In fact, running HS400 at
150 MHz (giving 300 MB/s) is the main motivation of this series, since
performance is still good but signal integrity problems are less
prevelant at 150 MHz.

[1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdfSigned-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

There's no reason to store the return value of rockchip_emmc_phy_power()
in a variable nor to check it.  Just return it.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

As of an earlier change in this series ("Documentation: mmc:
sdhci-of-arasan: Add ability to export card clock") the SDHCI driver
used on Rockchip SoCs can now expose its clock.  Let's now specify that
the PHY can use it.

Letting the PHY get access to this clock means it can adjust
phyctrl_frqsel field appropriately.  Although the Rockchip PHY appears
slightly different than the reference Arasan one, you can see that the
Arasan datasheet [1] had it defined as:
  Select the frequency range of DLL operation:
  3b'000 => 200MHz to 170 MHz
  3b'001 => 170MHz to 140 MHz
  3b'010 => 140MHz to 110 MHz
  3b'011 => 110MHz to 80MHz
  3b'100 => 80MHz to 50 MHz
  3b'101 => 275Mhz to 250MHz
  3b'110 => 250MHz to 225MHz
  3b'111 => 225MHz to 200MHz

On the Rockchip version of the PHY we have less granularity but the idea
is the same.

[1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdfSigned-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Some SD/eMMC PHYs (like the PHY from Arasan that is designed to work
with arasan,sdhci-5.1) need to know the card clock in order to function
properly.  Let's add the ability to expose this clock.  Any PHY that
needs to know the clock rate can add a reference and query the clock
rate.

At the moment we register a CLK_GET_RATE_NOCACHE clock that simply
allows querying the clock.  This allows us to be less intrusive with
regards to the main SDHCI driver, which has complex logic for adjusting
the SD clock.  Right now we always fully power cycle the PHY when the
clock changes and that gives the PHY a good chance to query our clock.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Some SD/eMMC PHYs (like the PHY from Arasan that is designed to work
with arasan,sdhci-5.1) need to know the card clock frequency in order to
function properly.  Physically in a SoC this clock is exported from the
SDHCI IP block to the PHY IP block and the PHY needs to know the speed.
Let's export the SDHCI card clock using a standard device tree mechanism
so that the PHY can get access to it and query the card clock frequency.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In the the earlier change in this series ("Documentation: mmc:
sdhci-of-arasan: Add soc-ctl-syscon for corecfg regs") we can see the
mechansim for specifying a syscon to properly set corecfg registers in
sdhci-of-arasan.  Now let's use this mechanism to properly set
corecfg_baseclkfreq on rk3399.

>From [1] the corecfg_baseclkfreq is supposed to be set to:
  Base Clock Frequency for SD Clock.
  This is the frequency of the xin_clk.

This is a relatively easy thing to do.  Note that we assume that xin_clk
is not dynamic and we can check the clock at probe time.  If any real
devices have a dynamic xin_clk future patches could register for
notifiers for the clock.

At the moment, setting corecfg_baseclkfreq is only supported for rk3399
since we need a specific map for each implementation.  The code is
written in a generic way that should make this easy to extend to other
SoCs.  Note that a specific compatible string for rk3399 is already in
use and so we add that to the table to match rk3399.

[1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdfSigned-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

As can be seen in Arasan's datasheet [1] there are several "corecfg"
settings in their SDHCI IP Block that are supposed to be controlled by
software.  Although the datasheet referenced is a bit vague about how to
access corecfg, in Figure 5 you can see that for Arasan's PHY (a
separate component than their SDHCI component) they describe the
"phyctrl" registers as being "FROM SOC CTL REG", implying that it's up
to the licensee of the Arasan IP block to implement these registers.  It
seems sane to assume that the "corecfg" registers in their SDHCI IP
block works in a similar way for all licensees of the IP Block.

Device tree has a model that allows a device to get a reference to
random registers located elsewhere in the SoC: sysctl.  Let's leverage
this model and allow adding a sysctl reference to access the control
registers for the Arasan SDHCI PHYs.

Having a reference to the control registers doesn't do much for us on
its own since the Arasan spec doesn't specify how these corecfg values
are laid out in memory.  In the SDHCI driver we'll need a map detailing
where each corecfg can be found in each implementation.  This map can be
found using the primary compatible string of the SDHCI device.  In that
spirit, document that existing rk3399 device trees already have a
specific compatible string, though up to now they've always been relying
on the driver supporting the generic.

Note that since existing devices seem to work fairly well as-is, we'll
list the syscon reference as "optional", but it's likely that we'll run
into much fewer problems if we can actually set the proper values in the
syscon, so it is strongly suggested that any SoCs where we have a map to
set the corecfg also include a reference to the syscon.

[1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdfSigned-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In commit 802ac39a ("mmc: sdhci-of-arasan: fix set_clock when a phy
is supported") we added code to power the PHY off and on whenever the
clock was changed but we avoided doing the power cycle code when the
clock was low speed.  Let's now do it always.

Although there may be other reasons for power cycling the PHY when the
clock changes, one of the main reasons is that we need to give the DLL a
chance to re-lock with the new clock.

One of the things that the DLL is for is tuning the Receive Clock in
HS200 mode and STRB in HS400 mode.  Thus it is clear that we should make
sure we power cycle the PHY (and wait for the DLL to lock) when we know
we'll be in one of these two speed modes.  That's what the original code
did, though it used the clock rate rather than the speed mode.  However,
even in speed modes other than HS200,/HS400 the DLL is used for
something since it can be clearly observed that the PHY doesn't function
properly if you leave the DLL off.

Although it appears less important to power cycle the PHY and wait for
the DLL to lock when not in HS200/HS400 modes (no bugs were reported),
it still seems wise to let the locking always happen nevertheless.

Note: as part of this, we make sure that we never try to turn the PHY on
when the clock is off (when the clock rate is 0).  The PHY cannot work
when the clock is off since its DLL can't lock.

This change requires ("phy: rockchip-emmc: Increase lock time
allowance") and will cause problems if picked without that change.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Previous PHY code waited a fixed amount of time for the DLL to lock at
power on time.  Unfortunately, the time for the DLL to lock is actually
a bit more dynamic and can be longer if the card clock is slower.

Instead of waiting a fixed 30 us, let's now dynamically wait until the
lock bit gets set.  We'll wait up to 10 ms which should be OK even if
the card clock is at the super slow 100 kHz.

On its own, this change makes the PHY power on code a little more
robust.  Before this change the PHY was relying on the eMMC code to make
sure the PHY was only powered on when the card clock was set to at least
50 MHz before, though this reliance wasn't documented anywhere.

This change will be even more useful in future changes where we actually
need to be able to wait for a DLL lock at slower clock speeds.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Some of the spacing was wrong (spaces instead of tabs), and due to
longer entries added later, the columns weren't aligned. Let's get
everything consistent.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The output tap delay controls helps maintain the hold requirements for
eMMC. The exact value is dependent on the SoC and other factors, though
it isn't really an exact science. But the default of 0 is not very good,
as it doesn't give the eMMC much hold time, so let's bump up to 4
(approx 90 degree phase?). If we need to configure this any further
(e.g., based on board or speed factors), we may need to consider a
device tree representation.
Suggested-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Signal integrity analysis has suggested we set these values. Do this in
power_on(), so that they get reconfigured after suspend/resume.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

According to the databook, 10.2us is the max time for dll to be ready to
work. However in testing, some chips need 20us for dll to be ready. This
patch adds some extra margin for dllrdy to be ready, fixing our
-ETIMEDOUT issues.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add SDHCI driver for Broadcom BRCMSTB SoCs.
This driver works with all ARM based SoCs and the 7425, 7429
and 7435 MIPS based SoCs.

The driver disables all UHS speed modes by default and relies
on the Device Tree node properties to enable these modes for
SoC/Board combinations that support them.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The example includes the properties required to enable UHS modes.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Apparently a cut-and-paste error, 'do_data_tag' is using 'brq' for data
size even though 'brq' has not been set up. Instead use blk_rq_sectors().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Certain Hynix eMMC 4.41 cards might get broken when HPI feature is used
and hence this patch disables the HPI feature for such buggy cards.

As some of the other features like BKOPs/Cache/Sanitize are dependent on
HPI feature, those features would also get disabled if HPI is disabled.
Signed-off-by: Pratibhasagar V <pratibha@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
[gdavis: Forward port and cleanup]
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc_select_bus_width() returns bus width (4 or 8) on success or
zero if unsupported. So only change mode if setting the bus width
is successful.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

If available, eMMC stack uses HC_ERASE_GRP_SIZE as the preferred erase
size. As some high capacity eMMC (64MB) reports this size to 512kB, the
discard operations end up taking very long time.

Improve the behaviour by instead calculating the preferred erase size
based on the eMMC size. In this way the discard operations becomes faster.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
[Ulf: Updated changelog and improved comment in code]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The sdhci-bcm2835 is no more needed since it has been replaced
by sdhci-iproc.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The sdhci-iproc also supports bcm2835. So this binding is obsolete.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

To slove the issue which was found on gru board for hs400.

[    4.616946] sdhci: Secure Digital Host Controller Interface driver
[    4.623135] sdhci: Copyright(c) Pierre Ossman
[    4.722575] sdhci-pltfm: SDHCI platform and OF driver helper
[    4.730962] sdhci-arasan fe330000.sdhci: No vmmc regulator found
[    4.737444] sdhci-arasan fe330000.sdhci: No vqmmc regulator found
[    4.774930] mmc0: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using ADMA
[    4.980295] mmc0: switch to high-speed from hs200 failed, err:-84
[    4.986487] mmc0: error -84 whilst initialising MMC card

We should change HS400 mode selection timing to meet JEDEC
specification. The JEDEC 5.1 said that change the frequency to <= 52MHZ
after HS_TIMING switch. Refer to section 6.6.2.3 "HS400" timing mode
selection:
Set the "Timing Interface" parameter in the HS_TIMING[185] field of the
Extended CSD register to 0x1 to switch to High Speed mode and then set
the clock frequency to a value not greater than 52MHZ.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

with CONFIG_HZ=100, the precision of jiffies is 10ms, and the
generic_cmd6_time of some card is also 10ms. then, may be current
time is only 5ms, but already timed out caused by jiffies precision.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Per JEDEC spec, it is not recommended to use CMD13 to get card status
after speed mode switch. below are two reason about this:
1. CMD13 cannot be guaranteed due to the asynchronous operation.
Therefore it is not recommended to use CMD13 to check busy completion
of the timing change indication.
2. After switch to HS200, CMD13 will get response of 0x800, and even the
busy signal gets de-asserted, the response of CMD13 is aslo 0x800.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Some MMC hosts do not support MMC_CAP_WAIT_WHILE_BUSY, but implements the
->card_busy() callback. In such cases, extend __mmc_switch() to use this
method to check card status after switch command.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

host->card_busy() was introduced for SD voltage switching which checks all
4 data lines.

Increasingly, host->card_busy is being used to poll the the busy signal
which is only data line 0 (DAT[0]).

The current logic in sdhci_card_busy() does not work in that case because
it returns false if any of the data lines is high.  It also ignores
possibilities:
	- data lines 1-3 are not connected and could show at any level
	- data lines 1-2 can be used by SDIO for other purposes

According to the SD specification, it is OK to check any of the data lines
for voltage switching, so change to use DAT[0] only.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Sparse complains about the implicit cast. Making it explicit is indeed
better coding style.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Currently sdhci-arasan 5.1 can support enhanced strobe function,
and we now limit it just for "arasan,sdhci-5.1". Add
mmc-hs400-enhanced-strobe in DT to enable the function if we're
sure our controller can support it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

We introduce HS400 with enhanced strobe function, so we need
to add it for debug show.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Controllers use data strobe line to latch data from devices
under hs400 mode, but not for cmd line. So since emmc 5.1, JEDEC
introduces enhanced strobe mode for latching cmd response from
emmc devices to host controllers. This new feature is optional,
so it depends both on device's cap and host's cap to decide
whether to use it or not.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch introduce mmc-hs400-enhanced-strobe for platforms
which want to enable enhanced strobe function from DT if the
mmc host controller claims to support enhanced strobe.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc-hs400-enhanced-strobe is used to claim that the
host can support hs400 mode with enhanced strobe
introduced by emmc 5.1 spec.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Submitters of device tree binding documentation may forget to CC
the subsystem maintainer if this is missing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Activating wakeup event is not enough to get a wakeup signal. The
corresponding events have to be enabled in the Interrupt Status Enable
Register too. It follows the specification and is needed at least by
sdhci-of-at91.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In sectors alignment check, brq->data.blocks means sectors of the
previous mqrq since data.blocks for mqrq_cur hasn't been updated yet.
data.blocks will be updated later in mmc_blk_packed_hdr_wrq_prep or
mmc_blk_rw_rq_prep.

static int mmc_blk_issue_rw_rq(struct mmc_queue *mq, ......
        ......
    struct mmc_blk_request *brq = &mq->mqrq_cur->brq;
Signed-off-by: Yuan Juntao <juntao.yuan@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Since commit 7ce45e95 ("mmc: sdhci: SD tuning is broken for some
controllers") sdhci_execute_tuning() no longer includes a timeout in its
loop counter(s) so remove portion of the comment regarding this.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Replace hardcoded values with meaningful names and document what we
know.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Pull ceph fix from Ilya Dryomov:
 "A fix for a long-standing bug in the incremental osdmap handling code
  that caused misdirected requests, tagged for stable"

  The tag is signed with a brand new key - Sage is on vacation and I
  didn't anticipate this"

* tag 'ceph-for-4.7-rc8' of git://github.com/ceph/ceph-client:
  libceph: apply new_state before new_up_client on incrementals

Pull networking fixes from David Miller:

 1) Fix memory leak in nftables, from Liping Zhang.

 2) Need to check result of vlan_insert_tag() in batman-adv otherwise we
    risk NULL skb derefs, from Sven Eckelmann.

 3) Check for dev_alloc_skb() failures in cfg80211, from Gregory
    Greenman.

 4) Handle properly when we have ppp_unregister_channel() happening in
    parallel with ppp_connect_channel(), from WANG Cong.

 5) Fix DCCP deadlock, from Eric Dumazet.

 6) Bail out properly in UDP if sk_filter() truncates the packet to be
    smaller than even the space that the protocol headers need.  From
    Michal Kubecek.

 7) Similarly for rose, dccp, and sctp, from Willem de Bruijn.

 8) Make TCP challenge ACKs less predictable, from Eric Dumazet.

 9) Fix infinite loop in bgmac_dma_tx_add() from Florian Fainelli.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
  packet: propagate sock_cmsg_send() error
  net/mlx5e: Fix del vxlan port command buffer memset
  packet: fix second argument of sock_tx_timestamp()
  net: switchdev: change ageing_time type to clock_t
  Update maintainer for EHEA driver.
  net/mlx4_en: Add resilience in low memory systems
  net/mlx4_en: Move filters cleanup to a proper location
  sctp: load transport header after sk_filter
  net/sched/sch_htb: clamp xstats tokens to fit into 32-bit int
  net: cavium: liquidio: Avoid dma_unmap_single on uninitialized ndata
  net: nb8800: Fix SKB leak in nb8800_receive()
  et131x: Fix logical vs bitwise check in et131x_tx_timeout()
  vlan: use a valid default mtu value for vlan over macsec
  net: bgmac: Fix infinite loop in bgmac_dma_tx_add()
  mlxsw: spectrum: Prevent invalid ingress buffer mapping
  mlxsw: spectrum: Prevent overwrite of DCB capability fields
  mlxsw: spectrum: Don't emit errors when PFC is disabled
  mlxsw: spectrum: Indicate support for autonegotiation
  mlxsw: spectrum: Force link training according to admin state
  r8152: add MODULE_VERSION
  ...