- 29 Oct, 2018 1 commit
-
-
git://anongit.freedesktop.org/drm/drmLinus Torvalds authored
Pull drm updates from Dave Airlie: "This is going to rebuild more than drm as it adds a new helper to list.h for doing bulk updates. Seemed like a reasonable addition to me. Otherwise the usual merge window stuff lots of i915 and amdgpu, not so much nouveau, and piles of everything else. Core: - Adds a new list.h helper for doing bulk list updates for TTM. - Don't leak fb address in smem_start to userspace (comes with EXPORT workaround for people using mali out of tree hacks) - udmabuf device to turn memfd regions into dma-buf - Per-plane blend mode property - ref/unref replacements with get/put - fbdev conflicting framebuffers code cleaned up - host-endian format variants - panel orientation quirk for Acer One 10 bridge: - TI SN65DSI86 chip support vkms: - GEM support. - Cursor support amdgpu: - Merge amdkfd and amdgpu into one module - CEC over DP AUX support - Picasso APU support + VCN dynamic powergating - Raven2 APU support - Vega20 enablement + kfd support - ACP powergating improvements - ABGR/XBGR display support - VCN jpeg support - xGMI support - DC i2c/aux cleanup - Ycbcr 4:2:0 support - GPUVM improvements - Powerplay and powerplay endian fixes - Display underflow fixes vmwgfx: - Move vmwgfx specific TTM code to vmwgfx - Split out vmwgfx buffer/resource validation code - Atomic operation rework bochs: - use more helpers - format/byteorder improvements qxl: - use more helpers i915: - GGTT coherency getparam - Turn off resource streamer API - More Icelake enablement + DMC firmware - Full PPGTT for Ivybridge, Haswell and Valleyview - DDB distribution based on resolution - Limited range DP display support nouveau: - CEC over DP AUX support - Initial HDMI 2.0 support virtio-gpu: - vmap support for PRIME objects tegra: - Initial Tegra194 support - DMA/IOMMU integration fixes msm: - a6xx perf improvements + clock prefix - GPU preemption optimisations - a6xx devfreq support - cursor support rockchip: - PX30 support - rgb output interface support mediatek: - HDMI output support on mt2701 and mt7623 rcar-du: - Interlaced modes on Gen3 - LVDS on R8A77980 - D3 and E3 SoC support hisilicon: - misc fixes mxsfb: - runtime pm support sun4i: - R40 TCON support - Allwinner A64 support - R40 HDMI support omapdrm: - Driver rework changing display pipeline ordering to use common code - DMM memory barrier and irq fixes - Errata workarounds exynos: - out-bridge support for LVDS bridge driver - Samsung 16x16 tiled format support - Plane alpha and pixel blend mode support tilcdc: - suspend/resume update mali-dp: - misc updates" * tag 'drm-next-2018-10-24' of git://anongit.freedesktop.org/drm/drm: (1382 commits) firmware/dmc/icl: Add missing MODULE_FIRMWARE() for Icelake. drm/i915/icl: Fix signal_levels drm/i915/icl: Fix DDI/TC port clk_off bits drm/i915/icl: create function to identify combophy port drm/i915/gen9+: Fix initial readout for Y tiled framebuffers drm/i915: Large page offsets for pread/pwrite drm/i915/selftests: Disable shrinker across mmap-exhaustion drm/i915/dp: Link train Fallback on eDP only if fallback link BW can fit panel's native mode drm/i915: Fix intel_dp_mst_best_encoder() drm/i915: Skip vcpi allocation for MSTB ports that are gone drm/i915: Don't unset intel_connector->mst_port drm/i915: Only reset seqno if actually idle drm/i915: Use the correct crtc when sanitizing plane mapping drm/i915: Restore vblank interrupts earlier drm/i915: Check fb stride against plane max stride drm/amdgpu/vcn:Fix uninitialized symbol error drm: panel-orientation-quirks: Add quirk for Acer One 10 (S1003) drm/amd/amdgpu: Fix debugfs error handling drm/amdgpu: Update gc_9_0 golden settings. drm/amd/powerplay: update PPtable with DC BTC and Tvr SocLimit fields ...
-
- 28 Oct, 2018 6 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linuxLinus Torvalds authored
Pull VLA removal from Kees Cook: "Globally warn on VLA use. This turns on "-Wvla" globally now that the last few trees with their VLA removals have landed (crypto, block, net, and powerpc). Arnd mentioned that there may be a couple more VLAs hiding in hard-to-find randconfigs, but nothing big has shaken out in the last month or so in linux-next. We should be basically VLA-free now! Wheee. :) Summary: - Remove unused fallback for BUILD_BUG_ON (which technically contains a VLA) - Lift -Wvla to the top-level Makefile" * tag 'vla-v4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: Makefile: Globally enable VLA warning compiler.h: give up __compiletime_assert_fallback() -
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuildLinus Torvalds authored
Pull Kbuild updates from Masahiro Yamada: - optimize kallsyms slightly - remove check for old CFLAGS usage - add some compiler flags unconditionally instead of evaluating $(call cc-option,...) - fix variable shadowing in host tools - refactor scripts/mkmakefile - refactor various makefiles * tag 'kbuild-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: modpost: Create macro to avoid variable shadowing ASN.1: Remove unnecessary shadowed local variable kbuild: use 'else ifeq' for checksrc to improve readability kbuild: remove unneeded link_multi_deps kbuild: add -Wno-unused-but-set-variable flag unconditionally kbuild: add -Wdeclaration-after-statement flag unconditionally kbuild: add -Wno-pointer-sign flag unconditionally modpost: remove leftover symbol prefix handling for module device table kbuild: simplify command line creation in scripts/mkmakefile kbuild: do not pass $(objtree) to scripts/mkmakefile kbuild: remove user ID check in scripts/mkmakefile kbuild: remove VERSION and PATCHLEVEL from $(objtree)/Makefile kbuild: add --include-dir flag only for out-of-tree build kbuild: remove dead code in cmd_files calculation in top Makefile kbuild: hide most of targets when running config or mixed targets kbuild: remove old check for CFLAGS use kbuild: prefix Makefile.dtbinst path with $(srctree) unconditionally kallsyms: remove left-over Blackfin code kallsyms: reduce size a little on 64-bit
-
Linus Torvalds authored
Merge tag 'linux-kselftest-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest Pull kselftest updates from Shuah Khan: "This Kselftest update for Linux 4.20-rc1 consists of: - Improvements to ftrace test suite from Masami Hiramatsu. - Color coded ftrace PASS / FAIL results from Steven Rostedt (VMware) to improve readability of reports. - watchdog Fixes and enhancement to add gettimeout and get|set pretimeout options from Jerry Hoemann. - Several fixes to warnings and spelling etc" * tag 'linux-kselftest-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (40 commits) selftests/ftrace: Strip escape sequences for log file selftests/ftrace: Use colored output when available selftests: fix warning: "_GNU_SOURCE" redefined selftests: kvm: Fix -Wformat warnings selftests/ftrace: Add color to the PASS / FAIL results kvm: selftests: fix spelling mistake "Insufficent" -> "Insufficient" selftests: gpio: Fix OUTPUT directory in Makefile selftests: gpio: restructure Makefile selftests: watchdog: Fix ioctl SET* error paths to take oneshot exit path selftests: watchdog: Add gettimeout and get|set pretimeout selftests: watchdog: Fix error message. selftests: watchdog: fix message when /dev/watchdog open fails selftests/ftrace: Add ftrace cpumask testcase selftests/ftrace: Add wakeup_rt tracer testcase selftests/ftrace: Add wakeup tracer testcase selftests/ftrace: Add stacktrace ftrace filter command testcase selftests/ftrace: Add trace_pipe testcase selftests/ftrace: Add function filter on module testcase selftests/ftrace: Add max stack tracer testcase selftests/ftrace: Add function profiling stat testcase ...
-
git://git.infradead.org/users/willy/linux-daxLinus Torvalds authored
Pull XArray conversion from Matthew Wilcox: "The XArray provides an improved interface to the radix tree data structure, providing locking as part of the API, specifying GFP flags at allocation time, eliminating preloading, less re-walking the tree, more efficient iterations and not exposing RCU-protected pointers to its users. This patch set 1. Introduces the XArray implementation 2. Converts the pagecache to use it 3. Converts memremap to use it The page cache is the most complex and important user of the radix tree, so converting it was most important. Converting the memremap code removes the only other user of the multiorder code, which allows us to remove the radix tree code that supported it. I have 40+ followup patches to convert many other users of the radix tree over to the XArray, but I'd like to get this part in first. The other conversions haven't been in linux-next and aren't suitable for applying yet, but you can see them in the xarray-conv branch if you're interested" * 'xarray' of git://git.infradead.org/users/willy/linux-dax: (90 commits) radix tree: Remove multiorder support radix tree test: Convert multiorder tests to XArray radix tree tests: Convert item_delete_rcu to XArray radix tree tests: Convert item_kill_tree to XArray radix tree tests: Move item_insert_order radix tree test suite: Remove multiorder benchmarking radix tree test suite: Remove __item_insert memremap: Convert to XArray xarray: Add range store functionality xarray: Move multiorder_check to in-kernel tests xarray: Move multiorder_shrink to kernel tests xarray: Move multiorder account test in-kernel radix tree test suite: Convert iteration test to XArray radix tree test suite: Convert tag_tagged_items to XArray radix tree: Remove radix_tree_clear_tags radix tree: Remove radix_tree_maybe_preload_order radix tree: Remove split/join code radix tree: Remove radix_tree_update_node_t page cache: Finish XArray conversion dax: Convert page fault handlers to XArray ...
-
Leonardo Bras authored
Create DEF_FIELD_ADDR_VAR as a more generic version of the DEF_FIELD_ADD macro, allowing usage of a variable name other than the struct element name. Also, sets DEF_FIELD_ADDR as a specific usage of DEF_FILD_ADDR_VAR in which the var name is the same as the struct element name. Then, makes use of DEF_FIELD_ADDR_VAR to create a variable of another name, in order to avoid variable shadowing. Signed-off-by:
Leonardo Bras <leobras.c@gmail.com> Signed-off-by:
Masahiro Yamada <yamada.masahiro@socionext.com>
-
Leonardo Bras authored
Remove an unnecessary shadowed local variable (start). It was used only once, with the same value it was started before the if block. Signed-off-by:
-
- 27 Oct, 2018 9 commits
-
-
Linus Torvalds authored
.. even when that "default y" is hidden syntactically as a default !EXPERT it's wrong. The only reason something should be 'default y' is if it used to be built-in, and it was made configurable, and the 'default y' is just retaining the status quo. Altheratively, the hardware for the driver has become _so_ common that it really makes sense for everybody to build it. Finally, one possible reason for 'default y' is because the option is not enabling any new code at all, but is just enabling other options (the networking people do this for vendor options, for example, so that you can disable whole vendors at a time). Clearly, none of these cases hold for the BigBen Interactive Kids' gamepad, and HID_BIGBEN_FF should thus most definitely not default to on for everybody. Cc: Hanno Zulla <kontakt@hanno.de> Cc: Jiri Kosina <jkosina@suse.cz> Signed-off-by:Linus Torvalds <torvalds@linux-foundation.org>
-
git://www.linux-watchdog.org/linux-watchdogLinus Torvalds authored
Pull watchdog updates from Wim Van Sebroeck: - Add Armada 37xx CPU watchdog - w83627hf_wdt: Add Support for NCT6796D, NCT6797D, NCT6798D - hpwdt: several improvements - renesas_wdt: SPDX identifiers, stop when unregistering, support for R7S9210 - rza_wdt: SPDX identifiers, support longer timeouts - core: fix null pointer dereference when releasing cdev - iTCO_wdt: Drop option vendorsupport=2 - sama5d4: fix timeout-sec usage - lantiq_wdt: convert to watchdog framework - several small fixes * tag 'linux-watchdog-4.20-rc1' of git://www.linux-watchdog.org/linux-watchdog: (30 commits) watchdog: ts4800: release syscon device node in ts4800_wdt_probe() watchdog: armada_37xx_wdt: use do_div for u64 division documentation: watchdog: add documentation for armada-37xx-wdt dt-bindings: watchdog: Document armada-37xx-wdt binding watchdog: Add support for Armada 37xx CPU watchdog dt-bindings: watchdog: add mpc8xxx-wdt support watchdog: mpc8xxx: provide boot status MAINTAINERS: Fix file pattern for MEN Z069 watchdog driver dt-bindings: watchdog: renesas-wdt: Add support for R7S9210 watchdog: rza_wdt: Support longer timeouts watchdog: hpwdt: Disable PreTimeout when Timeout is smaller watchdog: w83627hf_wdt: Support NCT6796D, NCT6797D, NCT6798D watchdog: mpc8xxx: use dev_xxxx() instead of pr_xxxx() watchdog: lantiq: add get_timeleft callback watchdog: lantiq: Convert to watchdog_device watchdog: lantiq: update register names to better match spec watchdog: sama5d4: fix timeout-sec usage watchdog: fix a small number of "watchog" typos in comments watchdog: rza_wdt: convert to SPDX identifiers watchdog: iTCO_wdt: Remove unused hooks ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/inputLinus Torvalds authored
Pull input updates from Dmitry Torokhov: "Just random driver fixups, nothing exiting" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: synaptics - avoid using uninitialized variable when probing Input: xen-kbdfront - mark expected switch fall-through Input: atmel_mxt_ts - mark expected switch fall-through Input: cyapa - mark expected switch fall-throughs Input: wm97xx-ts - fix exit path Input: of_touchscreen - add support for touchscreen-min-x|y Input: Fix DIR-685 touchkeys MAINTAINERS entry Input: elants_i2c - use DMA safe i2c when possible Input: silead - try firmware reload after unsuccessful resume Input: st1232 - set INPUT_PROP_DIRECT property Input: xilinx_ps2 - convert to using %pOFn instead of device_node.name Input: atmel_mxt_ts - fix multiple <linux/property.h> includes Input: sun4i-lradc - convert to using %pOFn instead of device_node.name Input: pwm-vibrator - correct pwms in DT binding example
-
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linuxLinus Torvalds authored
Pull RTC updates from Alexandre Belloni: "This cycle, there were mostly non urgent fixes in drivers. I also finally unexported the non managed registration. Subsystem: - non devm managed registration is now removed from the driver API - all the unnecessary rtc_valid_tm() calls have been removed Drivers: - abx80X: watchdog support - cmos: fix non ACPI support - sc27xx: fix alarm support - Remove a possible sysfs race condition for ab8500, ds1307, ds1685, isl1208 - Fix a possible race condition where an irq handler may be called before the rtc_device struct is allocated for mt6397, pl030, menelaus, armada38x" * tag 'rtc-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (54 commits) rtc: sc27xx: Always read normal alarm when registering RTC device rtc: sc27xx: Add check to see if need to enable the alarm interrupt rtc: sc27xx: Remove interrupts disable and clear in probe() rtc: sc27xx: Clear SPG value update interrupt status rtc: sc27xx: Set wakeup capability before registering rtc device rtc: s35390a: Change buf's type to u8 in s35390a_init rtc: ds1307: fix ds1339 wakealarm support rtc: ds1685: simplify getting .driver_data rtc: m41t80: mark expected switch fall-through rtc: tegra: Propagate errors from platform_get_irq() rtc: cmos: Remove the `use_acpi_alarm' module parameter for !ACPI rtc: cmos: Fix non-ACPI undefined reference to `hpet_rtc_interrupt' rtc: mv: let the core handle invalid alarms rtc: vr41xx: switch to rtc_time64_to_tm/rtc_tm_to_time64 rtc: ab8500: remove useless check rtc: ab8500: let the core handle range rtc: ab8500: use rtc_add_group rtc: rs5c348: report error when time is invalid rtc: rs5c348: remove forward declaration rtc: rs5c348: remove useless label ... -
Linus Torvalds authored
Merge tag 'led-fix-for-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds Pull LED fix from Jacek Anaszewski. * tag 'led-fix-for-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: leds: gpio: set led_dat->gpiod pointer for OF defined GPIO leds
-
Linus Torvalds authored
Commit 9ee3e066 ("HID: i2c-hid: override HID descriptors for certain devices") added a new dmi_system_id quirk table to override certain HID report descriptors for some systems that lack them. But the table wasn't properly terminated, causing the dmi matching to walk off into la-la-land, and starting to treat random data as dmi descriptor pointers, causing boot-time oopses if you were at all unlucky. Terminate the array. We really should have some way to just statically check that arrays that should be terminated by an empty entry actually are so. But the HID people really should have caught this themselves, rather than have me deal with an oops during the merge window. Tssk, tssk. Cc: Julian Sax <jsbc@gmx.de> Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com> Cc: Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Linus Torvalds authored
Merge updates from Andrew Morton: - a few misc things - ocfs2 updates - most of MM * emailed patches from Andrew Morton <akpm@linux-foundation.org>: (132 commits) hugetlbfs: dirty pages as they are added to pagecache mm: export add_swap_extent() mm: split SWP_FILE into SWP_ACTIVATED and SWP_FS tools/testing/selftests/vm/map_fixed_noreplace.c: add test for MAP_FIXED_NOREPLACE mm: thp: relocate flush_cache_range() in migrate_misplaced_transhuge_page() mm: thp: fix mmu_notifier in migrate_misplaced_transhuge_page() mm: thp: fix MADV_DONTNEED vs migrate_misplaced_transhuge_page race condition mm/kasan/quarantine.c: make quarantine_lock a raw_spinlock_t mm/gup: cache dev_pagemap while pinning pages Revert "x86/e820: put !E820_TYPE_RAM regions into memblock.reserved" mm: return zero_resv_unavail optimization mm: zero remaining unavailable struct pages tools/testing/selftests/vm/gup_benchmark.c: add MAP_HUGETLB option tools/testing/selftests/vm/gup_benchmark.c: add MAP_SHARED option tools/testing/selftests/vm/gup_benchmark.c: allow user specified file tools/testing/selftests/vm/gup_benchmark.c: fix 'write' flag usage mm/gup_benchmark.c: add additional pinning methods mm/gup_benchmark.c: time put_page() mm: don't raise MEMCG_OOM event due to failed high-order allocation mm/page-writeback.c: fix range_cyclic writeback vs writepages deadlock ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking fixes from David Miller: "What better way to start off a weekend than with some networking bug fixes: 1) net namespace leak in dump filtering code of ipv4 and ipv6, fixed by David Ahern and Bjørn Mork. 2) Handle bad checksums from hardware when using CHECKSUM_COMPLETE properly in UDP, from Sean Tranchetti. 3) Remove TCA_OPTIONS from policy validation, it turns out we don't consistently use nested attributes for this across all packet schedulers. From David Ahern. 4) Fix SKB corruption in cadence driver, from Tristram Ha. 5) Fix broken WoL handling in r8169 driver, from Heiner Kallweit. 6) Fix OOPS in pneigh_dump_table(), from Eric Dumazet" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (28 commits) net/neigh: fix NULL deref in pneigh_dump_table() net: allow traceroute with a specified interface in a vrf bridge: do not add port to router list when receives query with source 0.0.0.0 net/smc: fix smc_buf_unuse to use the lgr pointer ipv6/ndisc: Preserve IPv6 control buffer if protocol error handlers are called net/{ipv4,ipv6}: Do not put target net if input nsid is invalid lan743x: Remove SPI dependency from Microchip group. drivers: net: remove <net/busy_poll.h> inclusion when not needed net: phy: genphy_10g_driver: Avoid NULL pointer dereference r8169: fix broken Wake-on-LAN from S5 (poweroff) octeontx2-af: Use GFP_ATOMIC under spin lock net: ethernet: cadence: fix socket buffer corruption problem net/ipv6: Allow onlink routes to have a device mismatch if it is the default route net: sched: Remove TCA_OPTIONS from policy ice: Poll for link status change ice: Allocate VF interrupts and set queue map ice: Introduce ice_dev_onetime_setup net: hns3: Fix for warning uninitialized symbol hw_err_lst3 octeontx2-af: Copy the right amount of memory net: udp: fix handling of CHECKSUM_COMPLETE packets ... -
git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparcLinus Torvalds authored
Pull sparc fixes from David Miller: "Some more sparc fixups, mostly aimed at getting the allmodconfig build up and clean again" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc: sparc64: Rework xchg() definition to avoid warnings. sparc64: Export __node_distance. sparc64: Make corrupted user stacks more debuggable.
-
- 26 Oct, 2018 24 commits
-
-
Mike Kravetz authored
Some test systems were experiencing negative huge page reserve counts and incorrect file block counts. This was traced to /proc/sys/vm/drop_caches removing clean pages from hugetlbfs file pagecaches. When non-hugetlbfs explicit code removes the pages, the appropriate accounting is not performed. This can be recreated as follows: fallocate -l 2M /dev/hugepages/foo echo 1 > /proc/sys/vm/drop_caches fallocate -l 2M /dev/hugepages/foo grep -i huge /proc/meminfo AnonHugePages: 0 kB ShmemHugePages: 0 kB HugePages_Total: 2048 HugePages_Free: 2047 HugePages_Rsvd: 18446744073709551615 HugePages_Surp: 0 Hugepagesize: 2048 kB Hugetlb: 4194304 kB ls -lsh /dev/hugepages/foo 4.0M -rw-r--r--. 1 root root 2.0M Oct 17 20:05 /dev/hugepages/foo To address this issue, dirty pages as they are added to pagecache. This can easily be reproduced with fallocate as shown above. Read faulted pages will eventually end up being marked dirty. But there is a window where they are clean and could be impacted by code such as drop_caches. So, just dirty them all as they are added to the pagecache. Link: http://lkml.kernel.org/r/b5be45b8-5afe-56cd-9482-28384699a049@oracle.com Fixes: 6bda666a ("hugepages: fold find_or_alloc_pages into huge_no_page()") Signed-off-by:
Mike Kravetz <mike.kravetz@oracle.com> Acked-by:
Mihcla Hocko <mhocko@suse.com> Reviewed-by:
Khalid Aziz <khalid.aziz@oracle.com> Cc: Hugh Dickins <hughd@google.com> Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: "Aneesh Kumar K . V" <aneesh.kumar@linux.vnet.ibm.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: <stable@vger.kernel.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Omar Sandoval authored
Btrfs currently does not support swap files because swap's use of bmap does not work with copy-on-write and multiple devices. See 35054394 ("Btrfs: stop providing a bmap operation to avoid swapfile corruptions"). However, the swap code has a mechanism for the filesystem to manually add swap extents using add_swap_extent() from the ->swap_activate() aop. iomap has done this since 67482129 ("iomap: add a swapfile activation function"). Btrfs will do the same in a later patch, so export add_swap_extent(). Link: http://lkml.kernel.org/r/bb1208575e02829aae51b538709476964f97b1ea.1536704650.git.osandov@fb.comSigned-off-by:
Omar Sandoval <osandov@fb.com> Reviewed-by:
-
Omar Sandoval authored
The SWP_FILE flag serves two purposes: to make swap_{read,write}page() go through the filesystem, and to make swapoff() call ->swap_deactivate(). For Btrfs, we want the latter but not the former, so split this flag into two. This makes us always call ->swap_deactivate() if ->swap_activate() succeeded, not just if it didn't add any swap extents itself. This also resolves the issue of the very misleading name of SWP_FILE, which is only used for swap files over NFS. Link: http://lkml.kernel.org/r/6d63d8668c4287a4f6d203d65696e96f80abdfc7.1536704650.git.osandov@fb.comSigned-off-by:Nikolay Borisov <nborisov@suse.com> Reviewed-by:
-
Michael Ellerman authored
Add a test for MAP_FIXED_NOREPLACE, based on some code originally by Jann Horn. This would have caught the overlap bug reported by Daniel Micay. I originally suggested to Michal that we create MAP_FIXED_NOREPLACE, but instead of writing a selftest I spent my time bike-shedding whether it should be called MAP_FIXED_SAFE/NOCLOBBER/WEAK/NEW .. mea culpa. Link: http://lkml.kernel.org/r/20181013133929.28653-1-mpe@ellerman.id.auSigned-off-by:
Michael Ellerman <mpe@ellerman.id.au> Reviewed-by:
Kees Cook <keescook@chromium.org> Reviewed-by:
-
Andrea Arcangeli authored
There should be no cache left by the time we overwrite the old transhuge pmd with the new one. It's already too late to flush through the virtual address because we already copied the page data to the new physical address. So flush the cache before the data copy. Also delete the "end" variable to shutoff a "unused variable" warning on x86 where flush_cache_range() is a noop. Link: http://lkml.kernel.org/r/20181015202311.7209-1-aarcange@redhat.comSigned-off-by:
Andrea Arcangeli <aarcange@redhat.com> Acked-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Aaron Tomlin <atomlin@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Mel Gorman <mgorman@suse.de> Signed-off-by:
-
Andrea Arcangeli authored
change_huge_pmd() after arming the numa/protnone pmd doesn't flush the TLB right away. do_huge_pmd_numa_page() flushes the TLB before calling migrate_misplaced_transhuge_page(). By the time do_huge_pmd_numa_page() runs some CPU could still access the page through the TLB. change_huge_pmd() before arming the numa/protnone transhuge pmd calls mmu_notifier_invalidate_range_start(). So there's no need of mmu_notifier_invalidate_range_start()/mmu_notifier_invalidate_range_only_end() sequence in migrate_misplaced_transhuge_page() too, because by the time migrate_misplaced_transhuge_page() runs, the pmd mapping has already been invalidated in the secondary MMUs. It has to or if a secondary MMU can still write to the page, the migrate_page_copy() would lose data. However an explicit mmu_notifier_invalidate_range() is needed before migrate_misplaced_transhuge_page() starts copying the data of the transhuge page or the below can happen for MMU notifier users sharing the primary MMU pagetables and only implementing ->invalidate_range: CPU0 CPU1 GPU sharing linux pagetables using only ->invalidate_range ----------- ------------ --------- GPU secondary MMU writes to the page mapped by the transhuge pmd change_pmd_range() mmu..._range_start() ->invalidate_range_start() noop change_huge_pmd() set_pmd_at(numa/protnone) pmd_unlock() do_huge_pmd_numa_page() CPU TLB flush globally (1) CPU cannot write to page migrate_misplaced_transhuge_page() GPU writes to the page... migrate_page_copy() ...GPU stops writing to the page CPU TLB flush (2) mmu..._range_end() (3) ->invalidate_range_stop() noop ->invalidate_range() GPU secondary MMU is invalidated and cannot write to the page anymore (too late) Just like we need a CPU TLB flush (1) because the TLB flush (2) arrives too late, we also need a mmu_notifier_invalidate_range() before calling migrate_misplaced_transhuge_page(), because the ->invalidate_range() in (3) also arrives too late. This requirement is the result of the lazy optimization in change_huge_pmd() that releases the pmd_lock without first flushing the TLB and without first calling mmu_notifier_invalidate_range(). Even converting the removed mmu_notifier_invalidate_range_only_end() into a mmu_notifier_invalidate_range_end() would not have been enough to fix this, because it run after migrate_page_copy(). After the hugepage data copy is done migrate_misplaced_transhuge_page() can proceed and call set_pmd_at without having to flush the TLB nor any secondary MMUs because the secondary MMU invalidate, just like the CPU TLB flush, has to happen before the migrate_page_copy() is called or it would be a bug in the first place (and it was for drivers using ->invalidate_range()). KVM is unaffected because it doesn't implement ->invalidate_range(). The standard PAGE_SIZEd migrate_misplaced_page is less accelerated and uses the generic migrate_pages which transitions the pte from numa/protnone to a migration entry in try_to_unmap_one() and flushes TLBs and all mmu notifiers there before copying the page. Link: http://lkml.kernel.org/r/20181013002430.698-3-aarcange@redhat.comSigned-off-by:Mel Gorman <mgorman@suse.de> Acked-by:
Aaron Tomlin <atomlin@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Signed-off-by:
-
Andrea Arcangeli authored
Patch series "migrate_misplaced_transhuge_page race conditions". Aaron found a new instance of the THP MADV_DONTNEED race against pmdp_clear_flush* variants, that was apparently left unfixed. While looking into the race found by Aaron, I may have found two more issues in migrate_misplaced_transhuge_page. These race conditions would not cause kernel instability, but they'd corrupt userland data or leave data non zero after MADV_DONTNEED. I did only minor testing, and I don't expect to be able to reproduce this (especially the lack of ->invalidate_range before migrate_page_copy, requires the latest iommu hardware or infiniband to reproduce). The last patch is noop for x86 and it needs further review from maintainers of archs that implement flush_cache_range() (not in CC yet). To avoid confusion, it's not the first patch that introduces the bug fixed in the second patch, even before removing the pmdp_huge_clear_flush_notify, that _notify suffix was called after migrate_page_copy already run. This patch (of 3): This is a corollary of ced10803 ("thp: fix MADV_DONTNEED vs. numa balancing race"), 58ceeb6b ("thp: fix MADV_DONTNEED vs. MADV_FREE race") and 5b7abeae ("thp: fix MADV_DONTNEED vs clear soft dirty race). When the above three fixes where posted Dave asked https://lkml.kernel.org/r/929b3844-aec2-0111-fef7-8002f9d4e2b9@intel.com but apparently this was missed. The pmdp_clear_flush* in migrate_misplaced_transhuge_page() was introduced in a54a407f ("mm: Close races between THP migration and PMD numa clearing"). The important part of such commit is only the part where the page lock is not released until the first do_huge_pmd_numa_page() finished disarming the pagenuma/protnone. The addition of pmdp_clear_flush() wasn't beneficial to such commit and there's no commentary about such an addition either. I guess the pmdp_clear_flush() in such commit was added just in case for safety, but it ended up introducing the MADV_DONTNEED race condition found by Aaron. At that point in time nobody thought of such kind of MADV_DONTNEED race conditions yet (they were fixed later) so the code may have looked more robust by adding the pmdp_clear_flush(). This specific race condition won't destabilize the kernel, but it can confuse userland because after MADV_DONTNEED the memory won't be zeroed out. This also optimizes the code and removes a superfluous TLB flush. [akpm@linux-foundation.org: reflow comment to 80 cols, fix grammar and typo (beacuse)] Link: http://lkml.kernel.org/r/20181013002430.698-2-aarcange@redhat.comSigned-off-by:
-
Clark Williams authored
The static lock quarantine_lock is used in quarantine.c to protect the quarantine queue datastructures. It is taken inside quarantine queue manipulation routines (quarantine_put(), quarantine_reduce() and quarantine_remove_cache()), with IRQs disabled. This is not a problem on a stock kernel but is problematic on an RT kernel where spin locks are sleeping spinlocks, which can sleep and can not be acquired with disabled interrupts. Convert the quarantine_lock to a raw spinlock_t. The usage of quarantine_lock is confined to quarantine.c and the work performed while the lock is held is used for debug purpose. [bigeasy@linutronix.de: slightly altered the commit message] Link: http://lkml.kernel.org/r/20181010214945.5owshc3mlrh74z4b@linutronix.deSigned-off-by:
Clark Williams <williams@redhat.com> Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
-
Keith Busch authored
Getting pages from ZONE_DEVICE memory needs to check the backing device's live-ness, which is tracked in the device's dev_pagemap metadata. This metadata is stored in a radix tree and looking it up adds measurable software overhead. This patch avoids repeating this relatively costly operation when dev_pagemap is used by caching the last dev_pagemap while getting user pages. The gup_benchmark kernel self test reports this reduces time to get user pages to as low as 1/3 of the previous time. Link: http://lkml.kernel.org/r/20181012173040.15669-1-keith.busch@intel.comSigned-off-by:
Keith Busch <keith.busch@intel.com> Reviewed-by:
Dan Williams <dan.j.williams@intel.com> Acked-by:
-
Masayoshi Mizuma authored
commit 124049de ("x86/e820: put !E820_TYPE_RAM regions into memblock.reserved") breaks movable_node kernel option because it changed the memory gap range to reserved memblock. So, the node is marked as Normal zone even if the SRAT has Hot pluggable affinity. ===================================================================== kernel: BIOS-e820: [mem 0x0000180000000000-0x0000180fffffffff] usable kernel: BIOS-e820: [mem 0x00001c0000000000-0x00001c0fffffffff] usable ... kernel: reserved[0x12]#011[0x0000181000000000-0x00001bffffffffff], 0x000003f000000000 bytes flags: 0x0 ... kernel: ACPI: SRAT: Node 2 PXM 6 [mem 0x180000000000-0x1bffffffffff] hotplug kernel: ACPI: SRAT: Node 3 PXM 7 [mem 0x1c0000000000-0x1fffffffffff] hotplug ... kernel: Movable zone start for each node kernel: Node 3: 0x00001c0000000000 kernel: Early memory node ranges ... ===================================================================== The original issue is fixed by the former patches, so let's revert commit 124049de ("x86/e820: put !E820_TYPE_RAM regions into memblock.reserved"). Link: http://lkml.kernel.org/r/20181002143821.5112-4-msys.mizuma@gmail.comSigned-off-by:
Masayoshi Mizuma <m.mizuma@jp.fujitsu.com> Reviewed-by:
Pavel Tatashin <pavel.tatashin@microsoft.com> Acked-by:
Ingo Molnar <mingo@kernel.org> Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Oscar Salvador <osalvador@suse.de> Signed-off-by:
-
Pavel Tatashin authored
When checking for valid pfns in zero_resv_unavail(), it is not necessary to verify that pfns within pageblock_nr_pages ranges are valid, only the first one needs to be checked. This is because memory for pages are allocated in contiguous chunks that contain pageblock_nr_pages struct pages. Link: http://lkml.kernel.org/r/20181002143821.5112-3-msys.mizuma@gmail.comSigned-off-by:
Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Reviewed-by:
Oscar Salvador <osalvador@suse.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Michal Hocko <mhocko@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Naoya Horiguchi authored
Patch series "mm: Fix for movable_node boot option", v3. This patch series contains a fix for the movable_node boot option issue which was introduced by commit 124049de ("x86/e820: put !E820_TYPE_RAM regions into memblock.reserved"). The commit breaks the option because it changed the memory gap range to reserved memblock. So, the node is marked as Normal zone even if the SRAT has Hot pluggable affinity. First and second patch fix the original issue which the commit tried to fix, then revert the commit. This patch (of 3): There is a kernel panic that is triggered when reading /proc/kpageflags on the kernel booted with kernel parameter 'memmap=nn[KMG]!ss[KMG]': BUG: unable to handle kernel paging request at fffffffffffffffe PGD 9b20e067 P4D 9b20e067 PUD 9b210067 PMD 0 Oops: 0000 [#1] SMP PTI CPU: 2 PID: 1728 Comm: page-types Not tainted 4.17.0-rc6-mm1-v4.17-rc6-180605-0816-00236-g2dfb086ef02c+ #160 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-2.fc28 04/01/2014 RIP: 0010:stable_page_flags+0x27/0x3c0 Code: 00 00 00 0f 1f 44 00 00 48 85 ff 0f 84 a0 03 00 00 41 54 55 49 89 fc 53 48 8b 57 08 48 8b 2f 48 8d 42 ff 83 e2 01 48 0f 44 c7 <48> 8b 00 f6 c4 01 0f 84 10 03 00 00 31 db 49 8b 54 24 08 4c 89 e7 RSP: 0018:ffffbbd44111fde0 EFLAGS: 00010202 RAX: fffffffffffffffe RBX: 00007fffffffeff9 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 0000000000000202 RDI: ffffed1182fff5c0 RBP: ffffffffffffffff R08: 0000000000000001 R09: 0000000000000001 R10: ffffbbd44111fed8 R11: 0000000000000000 R12: ffffed1182fff5c0 R13: 00000000000bffd7 R14: 0000000002fff5c0 R15: ffffbbd44111ff10 FS: 00007efc4335a500(0000) GS:ffff93a5bfc00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: fffffffffffffffe CR3: 00000000b2a58000 CR4: 00000000001406e0 Call Trace: kpageflags_read+0xc7/0x120 proc_reg_read+0x3c/0x60 __vfs_read+0x36/0x170 vfs_read+0x89/0x130 ksys_pread64+0x71/0x90 do_syscall_64+0x5b/0x160 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x7efc42e75e23 Code: 09 00 ba 9f 01 00 00 e8 ab 81 f4 ff 66 2e 0f 1f 84 00 00 00 00 00 90 83 3d 29 0a 2d 00 00 75 13 49 89 ca b8 11 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 34 c3 48 83 ec 08 e8 db d3 01 00 48 89 04 24 According to kernel bisection, this problem became visible due to commit f7f99100 which changes how struct pages are initialized. Memblock layout affects the pfn ranges covered by node/zone. Consider that we have a VM with 2 NUMA nodes and each node has 4GB memory, and the default (no memmap= given) memblock layout is like below: MEMBLOCK configuration: memory size = 0x00000001fff75c00 reserved size = 0x000000000300c000 memory.cnt = 0x4 memory[0x0] [0x0000000000001000-0x000000000009efff], 0x000000000009e000 bytes on node 0 flags: 0x0 memory[0x1] [0x0000000000100000-0x00000000bffd6fff], 0x00000000bfed7000 bytes on node 0 flags: 0x0 memory[0x2] [0x0000000100000000-0x000000013fffffff], 0x0000000040000000 bytes on node 0 flags: 0x0 memory[0x3] [0x0000000140000000-0x000000023fffffff], 0x0000000100000000 bytes on node 1 flags: 0x0 ... If you give memmap=1G!4G (so it just covers memory[0x2]), the range [0x100000000-0x13fffffff] is gone: MEMBLOCK configuration: memory size = 0x00000001bff75c00 reserved size = 0x000000000300c000 memory.cnt = 0x3 memory[0x0] [0x0000000000001000-0x000000000009efff], 0x000000000009e000 bytes on node 0 flags: 0x0 memory[0x1] [0x0000000000100000-0x00000000bffd6fff], 0x00000000bfed7000 bytes on node 0 flags: 0x0 memory[0x2] [0x0000000140000000-0x000000023fffffff], 0x0000000100000000 bytes on node 1 flags: 0x0 ... This causes shrinking node 0's pfn range because it is calculated by the address range of memblock.memory. So some of struct pages in the gap range are left uninitialized. We have a function zero_resv_unavail() which does zeroing the struct pages outside memblock.memory, but currently it covers only the reserved unavailable range (i.e. memblock.memory && !memblock.reserved). This patch extends it to cover all unavailable range, which fixes the reported issue. Link: http://lkml.kernel.org/r/20181002143821.5112-2-msys.mizuma@gmail.com Fixes: f7f99100 ("mm: stop zeroing memory during allocation in vmemmap") Signed-off-by:
-
Keith Busch authored
Add a new option '-H' to the gup benchmark to help understand how hugetlb mapping pages compare with the default. Link: http://lkml.kernel.org/r/20181010195605.10689-6-keith.busch@intel.comSigned-off-by:
-
Keith Busch authored
Add a new benchmark option, -S, to request MAP_SHARED. This can be used to compare with MAP_PRIVATE, or for files that require this option, like dax. Link: http://lkml.kernel.org/r/20181010195605.10689-5-keith.busch@intel.comSigned-off-by:
-
Keith Busch authored
Allow a user to specify a file to map by adding a new option, '-f', providing a means to test various file backings. If not specified, the benchmark will use a private mapping of /dev/zero, which produces an anonymous mapping as before. [akpm@linux-foundation.org: avoid using comma operator] Link: http://lkml.kernel.org/r/20181010195605.10689-4-keith.busch@intel.comSigned-off-by:
-
Keith Busch authored
If the '-w' parameter was provided, the benchmark would exit due to a mssing 'break'. Link: http://lkml.kernel.org/r/20181010195605.10689-3-keith.busch@intel.comSigned-off-by:
-
Keith Busch authored
Provide new gup benchmark ioctl commands to run different user page pinning methods, get_user_pages_longterm() and get_user_pages(), in addition to the existing get_user_pages_fast(). Link: http://lkml.kernel.org/r/20181010195605.10689-2-keith.busch@intel.comSigned-off-by:
-
Keith Busch authored
We'd like to measure time to unpin user pages, so this adds a second benchmark timer on put_page, separate from get_page. Adding the field breaks this ioctl ABI, but should be okay since this an in-tree kernel selftest. [akpm@linux-foundation.org: add expansion to struct gup_benchmark for future use] Link: http://lkml.kernel.org/r/20181010195605.10689-1-keith.busch@intel.comSigned-off-by:
-
Roman Gushchin authored
It was reported that on some of our machines containers were restarted with OOM symptoms without an obvious reason. Despite there were almost no memory pressure and plenty of page cache, MEMCG_OOM event was raised occasionally, causing the container management software to think, that OOM has happened. However, no tasks have been killed. The following investigation showed that the problem is caused by a failing attempt to charge a high-order page. In such case, the OOM killer is never invoked. As shown below, it can happen under conditions, which are very far from a real OOM: e.g. there is plenty of clean page cache and no memory pressure. There is no sense in raising an OOM event in this case, as it might confuse a user and lead to wrong and excessive actions (e.g. restart the workload, as in my case). Let's look at the charging path in try_charge(). If the memory usage is about memory.max, which is absolutely natural for most memory cgroups, we try to reclaim some pages. Even if we were able to reclaim enough memory for the allocation, the following check can fail due to a race with another concurrent allocation: if (mem_cgroup_margin(mem_over_limit) >= nr_pages) goto retry; For regular pages the following condition will save us from triggering the OOM: if (nr_reclaimed && nr_pages <= (1 << PAGE_ALLOC_COSTLY_ORDER)) goto retry; But for high-order allocation this condition will intentionally fail. The reason behind is that we'll likely fall to regular pages anyway, so it's ok and even preferred to return ENOMEM. In this case the idea of raising MEMCG_OOM looks dubious. Fix this by moving MEMCG_OOM raising to mem_cgroup_oom() after allocation order check, so that the event won't be raised for high order allocations. This change doesn't affect regular pages allocation and charging. Link: http://lkml.kernel.org/r/20181004214050.7417-1-guro@fb.comSigned-off-by:Roman Gushchin <guro@fb.com> Acked-by:
David Rientjes <rientjes@google.com> Acked-by:
Michal Hocko <mhocko@kernel.org> Acked-by:
Johannes Weiner <hannes@cmpxchg.org> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Signed-off-by:
-
Dave Chinner authored
We've recently seen a workload on XFS filesystems with a repeatable deadlock between background writeback and a multi-process application doing concurrent writes and fsyncs to a small range of a file. range_cyclic writeback Process 1 Process 2 xfs_vm_writepages write_cache_pages writeback_index = 2 cycled = 0 .... find page 2 dirty lock Page 2 ->writepage page 2 writeback page 2 clean page 2 added to bio no more pages write() locks page 1 dirties page 1 locks page 2 dirties page 1 fsync() .... xfs_vm_writepages write_cache_pages start index 0 find page 1 towrite lock Page 1 ->writepage page 1 writeback page 1 clean page 1 added to bio find page 2 towrite lock Page 2 page 2 is writeback <blocks> write() locks page 1 dirties page 1 fsync() .... xfs_vm_writepages write_cache_pages start index 0 !done && !cycled sets index to 0, restarts lookup find page 1 dirty find page 1 towrite lock Page 1 page 1 is writeback <blocks> lock Page 1 <blocks> DEADLOCK because: - process 1 needs page 2 writeback to complete to make enough progress to issue IO pending for page 1 - writeback needs page 1 writeback to complete so process 2 can progress and unlock the page it is blocked on, then it can issue the IO pending for page 2 - process 2 can't make progress until process 1 issues IO for page 1 The underlying cause of the problem here is that range_cyclic writeback is processing pages in descending index order as we hold higher index pages in a structure controlled from above write_cache_pages(). The write_cache_pages() caller needs to be able to submit these pages for IO before write_cache_pages restarts writeback at mapping index 0 to avoid wcp inverting the page lock/writeback wait order. generic_writepages() is not susceptible to this bug as it has no private context held across write_cache_pages() - filesystems using this infrastructure always submit pages in ->writepage immediately and so there is no problem with range_cyclic going back to mapping index 0. However: mpage_writepages() has a private bio context, exofs_writepages() has page_collect fuse_writepages() has fuse_fill_wb_data nfs_writepages() has nfs_pageio_descriptor xfs_vm_writepages() has xfs_writepage_ctx All of these ->writepages implementations can hold pages under writeback in their private structures until write_cache_pages() returns, and hence they are all susceptible to this deadlock. Also worth noting is that ext4 has it's own bastardised version of write_cache_pages() and so it /may/ have an equivalent deadlock. I looked at the code long enough to understand that it has a similar retry loop for range_cyclic writeback reaching the end of the file and then promptly ran away before my eyes bled too much. I'll leave it for the ext4 developers to determine if their code is actually has this deadlock and how to fix it if it has. There's a few ways I can see avoid this deadlock. There's probably more, but these are the first I've though of: 1. get rid of range_cyclic altogether 2. range_cyclic always stops at EOF, and we start again from writeback index 0 on the next call into write_cache_pages() 2a. wcp also returns EAGAIN to ->writepages implementations to indicate range cyclic has hit EOF. writepages implementations can then flush the current context and call wpc again to continue. i.e. lift the retry into the ->writepages implementation 3. range_cyclic uses trylock_page() rather than lock_page(), and it skips pages it can't lock without blocking. It will already do this for pages under writeback, so this seems like a no-brainer 3a. all non-WB_SYNC_ALL writeback uses trylock_page() to avoid blocking as per pages under writeback. I don't think #1 is an option - range_cyclic prevents frequently dirtied lower file offset from starving background writeback of rarely touched higher file offsets. #2 is simple, and I don't think it will have any impact on performance as going back to the start of the file implies an immediate seek. We'll have exactly the same number of seeks if we switch writeback to another inode, and then come back to this one later and restart from index 0. #2a is pretty much "status quo without the deadlock". Moving the retry loop up into the wcp caller means we can issue IO on the pending pages before calling wcp again, and so avoid locking or waiting on pages in the wrong order. I'm not convinced we need to do this given that we get the same thing from #2 on the next writeback call from the writeback infrastructure. #3 is really just a band-aid - it doesn't fix the access/wait inversion problem, just prevents it from becoming a deadlock situation. I'd prefer we fix the inversion, not sweep it under the carpet like this. #3a is really an optimisation that just so happens to include the band-aid fix of #3. So it seems that the simplest way to fix this issue is to implement solution #2 Link: http://lkml.kernel.org/r/20181005054526.21507-1-david@fromorbit.comSigned-off-by:Dave Chinner <dchinner@redhat.com> Reviewed-by:
Jan Kara <jack@suse.de> Cc: Nicholas Piggin <npiggin@gmail.com> Signed-off-by:
-
Pavel Tatashin authored
memmap_init_zone, is getting complex, because it is called from different contexts: hotplug, and during boot, and also because it must handle some architecture quirks. One of them is mirrored memory. Move the code that decides whether to skip mirrored memory outside of memmap_init_zone, into a separate function. [pasha.tatashin@oracle.com: uninline overlap_memmap_init()] Link: http://lkml.kernel.org/r/20180726193509.3326-4-pasha.tatashin@oracle.com Link: http://lkml.kernel.org/r/20180724235520.10200-4-pasha.tatashin@oracle.comSigned-off-by:
Pavel Tatashin <pasha.tatashin@oracle.com> Reviewed-by:
-
Pavel Tatashin authored
update_defer_init() should be called only when struct page is about to be initialized. Because it counts number of initialized struct pages, but there we may skip struct pages if there is some mirrored memory. So move, update_defer_init() after checking for mirrored memory. Also, rename update_defer_init() to defer_init() and reverse the return boolean to emphasize that this is a boolean function, that tells that the reset of memmap initialization should be deferred. Make this function self-contained: do not pass number of already initialized pages in this zone by using static counters. I found this bug by reading the code. The effect is that fewer than expected struct pages are initialized early in boot, and it is possible that in some corner cases we may fail to boot when mirrored pages are used. The deferred on demand code should somewhat mitigate this. But this still brings some inconsistencies compared to when booting without mirrored pages, so it is better to fix. [pasha.tatashin@oracle.com: add comment about defer_init's lack of locking] Link: http://lkml.kernel.org/r/20180726193509.3326-3-pasha.tatashin@oracle.com [akpm@linux-foundation.org: make defer_init non-inline, __meminit] Link: http://lkml.kernel.org/r/20180724235520.10200-3-pasha.tatashin@oracle.comSigned-off-by:
-
Pavel Tatashin authored
memmap_init is sometimes a macro sometimes a function based on __HAVE_ARCH_MEMMAP_INIT. It is only a function on ia64. Make memmap_init a weak function instead, and let ia64 redefine it. Link: http://lkml.kernel.org/r/20180724235520.10200-2-pasha.tatashin@oracle.comSigned-off-by:
-
Kirill Tkhai authored
This will allow to use generic refcount_t interfaces to check counters overflow instead of currently existing VM_BUG_ON(). The only difference after the patch is VM_BUG_ON() may cause BUG(), while refcount_t fires with WARN(). But this seems not to be significant here, since such the problems are usually caught by syzbot with panic-on-warn enabled. Link: http://lkml.kernel.org/r/153910718919.7006.13400779039257185427.stgit@localhost.localdomainSigned-off-by:
Kirill Tkhai <ktkhai@virtuozzo.com> Reviewed-by:
-
