- 10 May, 2015 12 commits
-
-
Linus Walleij authored
When cross-compiling the IIO tools we need to opportunity to specify a cross compiler prefix and some extra CFLAGS. This patch enables this in the same way as for other stuff in tools. Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Acked-by:
Daniel Baluta <daniel.baluta@intel.com> Signed-off-by:
Jonathan Cameron <jic23@kernel.org>
-
Daniel Baluta authored
We assume that ACPI device tables use MMC35240 to identify MEMSIC's 3 axis magnetic sensor. Signed-off-by:
-
Daniel Baluta authored
We rely on regmap to save the state of the registers at suspend, and then we do an explicit sync at resume. Signed-off-by:
-
Daniel Baluta authored
Minimal implementation for MMC35240 3-axis magnetometer sensor. It provides processed readings and possiblity to change the sampling frequency. Signed-off-by:
-
Irina Tirdea authored
Export the oversampling ratio so that the user can change the number of repetions for x/y/z axis. The sampling frequency is limited by the oversampling ratio. The available sampling frequencies might change depending on the values of oversampling_ratio. The specification can be downloaded from: http://ae-bst.resource.bosch.com/media/products/dokumente/bmc150/BST-BMC150-DS000-04.pdf. Signed-off-by:
Irina Tirdea <irina.tirdea@intel.com> Signed-off-by:
-
Irina Tirdea authored
Some magnetometers can perform a number of repetitions in HW for each measurement to increase accuracy. One example is Bosch BMC150: http://ae-bst.resource.bosch.com/media/products/dokumente/bmc150/BST-BMC150-DS000-04.pdf. Introduce an interface to set the oversampling ratio for these devices. Signed-off-by:
-
Irina Tirdea authored
Add binding documentation for Bosch BMC150 magnetometer. Signed-off-by:
-
Irina Tirdea authored
Add support for the Bosh BMC150 Magnetometer. The specification can be downloaded from: http://ae-bst.resource.bosch.com/media/products/dokumente/bmc150/BST-BMC150-DS000-04.pdf. The chip contains both an accelerometer and a magnetometer. This patch adds support only for the magnetometer part. The temperature compensation formulas are based on bmm050_api.c authored by contact@bosch.sensortec.com. Signed-off-by:
-
Geert Uytterhoeven authored
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer functionality only, can still be compiled if GPIOLIB is not enabled. Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where appropriate. Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Cc: Jonathan Cameron <jic23@kernel.org> Cc: linux-iio@vger.kernel.org Cc: devel@driverdev.osuosl.org Signed-off-by:
-
Geert Uytterhoeven authored
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer functionality only, can still be compiled if GPIOLIB is not enabled. Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where appropriate. Signed-off-by:
-
Tiberiu Breana authored
Added interrupt support for proximity threshold events to the stk3310 driver. Signed-off-by:
Tiberiu Breana <tiberiu.a.breana@intel.com> Signed-off-by:
-
Tiberiu Breana authored
Minimal implementation of an IIO driver for the Sensortek STK3310 ambient light and proximity sensor. The STK3311 model is also supported. Includes: - ACPI support; - read_raw and write_raw; - reading and setting configuration parameters for gain/scale and integration time for both ALS and PS. - power management Signed-off-by:
-
- 09 May, 2015 1 commit
-
-
Greg Kroah-Hartman authored
Merge tag 'iio-for-v4.2a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next Jonathan writes: First round of new drivers, functionality and cleanups for the 4.2 cycle New drivers / device support * st sensors driver, lsm303dlh magnetometer support. * ltr501 - support ltr301 and ltr559 chips. New functionality * IIO_CHAN_INFO_CALIBEMISSIVITY for thermopile sensors. * kxcjk1013 - make driver operational with external trigger. * Add iio targets to the tools Makefile. Cleanups * st sensors - more helpful error message if device id wrong or irq request fails, explicitly make the Block Data Update optional rather than relying on writes to address 0 not doing anything, make interrupt support optional (Not always wired, and not all devices actually have an interrupt line.) * kxcjk-1013 white space additions for readability, add the KXCJ9000 ACPI id as seen in the wild. * sx9500 - GPIO reset support, refactor the GPIO interrupt code, add power management, optimize power usage by powering down when possible, rename the gpio interrupt pin to be more useful, trivial return path simplification, trivial formatting fixes. * isl29018 - move towards ABI compliance with a view to moving this driver out of staging, add some brackets to ensure code works as expected. Note there is no actual bug as the condition being tested is always true (with current devices). * ltr501 - add regmap support to get caching etc for later patches, fix a parameter sanity check that always fails (bug introduced earlier in this series), ACPI enumeration support, interrupt rate control support, interrupt support in general and integration time control support, code alignment cleanups. * mma9553 - a number of little cleanups following a review from Hartmut after I'd already applied the original driver patch. * tmp006 - prefix some defines with TMP006 for consistency. * tsl4531 - cleanup some wrong prefixes, presumably from copy and paste. * mlx90614 - check for errors in read values, add power management, add emissivity setting, add device tree binding documentation, fix a duplicate const warning. * ti_am335x_adc - refactor the DT parsing into a separate function.
-
- 08 May, 2015 27 commits
-
-
Jes Sorensen authored
Signed-off-by:
Jes Sorensen <Jes.Sorensen@redhat.com> Signed-off-by:
Benjamin Romer <benjamin.romer@unisys.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jes Sorensen authored
Signed-off-by:
-
Jes Sorensen authored
Signed-off-by:
-
Jes Sorensen authored
Signed-off-by:
-
Jes Sorensen authored
Signed-off-by:
-
Jes Sorensen authored
In addition remove unused parser_init() Signed-off-by:
-
Jes Sorensen authored
This allows the caller to specify an appropriate GFP flag instead of hardcoding the lowest common denominator. Signed-off-by:
-
Benjamin Romer authored
The visorutil directory is still mentioned in the top level makefile for the Unisys drivers, so remove it. Signed-off-by:
-
Benjamin Romer authored
Removing visorutil made it impossible to build visorbus. Remove the config setting from the Kconfig so the module can be enabled in the build. Signed-off-by:
-
Erik Arfvidson authored
This patch removes visorutil directory, move periodic_work.c into the visorbus directory. Signed-off-by:
Erik Arfvidson <erik.arfvidson@unisys.com> Signed-off-by:
-
Erik Arfvidson authored
This patch move the needed linux include files from timskmod.h to the files that calls those include. Also procobjecttree.h is removed since it is dead code. Signed-off-by:
-
Erik Arfvidson authored
This patch removes charqueue.[ch] since it no longer called Signed-off-by:
-
Erik Arfvidson authored
This patch removes all timksmod.h pound defines. It also removes visorkmodutils.c since it no longer has any use by itself. Since visorkmodutils.c is no longer needed the module_init for visorchipset.c is modified to call visorutil_spar_detect directly instead of the extern variable in timksmod.h. Signed-off-by:
-
Benjamin Romer authored
Later patches will require PCI and ACPI support in the kernel, so add these features to the Kconfig. Signed-off-by:
-
Prarit Bhargava authored
According to Unisys, another OS detects the PNP0A07 as the auto load device. We can also do this in the linux kernel by simply converting the driver over to the ACPI driver model. Notes: This changes the usage of __init and it had to be removed from some functions to avoid a !__init function calling an __init function. Additionally I also cleaned up the headers in visorchipset.c since I was adding a header file. Signed-off-by:
Prarit Bhargava <prarit@redhat.com> Signed-off-by:
-
Prarit Bhargava authored
These shouldn't be defined in the code and can be replaced with the standard bool, true, and false usage that the kernel uses. Signed-off-by:
-
Jes Sorensen authored
Signed-off-by:
-
Jes Sorensen authored
visorchannel's signal code should call visorchannel_write() directly. This is more consistent and cleaner, and allows us to remove the last memregion call. Signed-off-by:
-
Jes Sorensen authored
Signed-off-by:
-
Jes Sorensen authored
There is no benefit to calling visor_memregion_read() at this point. Signed-off-by:
-
Jes Sorensen authored
Signed-off-by:
-
Jes Sorensen authored
Note, this changes the behavior of visorchannel_read(). The old code would return the channel header, if the offset argument was 0, and the caller tried to read beyond the size of the visorchannel. Note this only worked for offset == 0, but not for (offset > 0) && (offset < header_size), which was inconsistent. The new implementation returns an error if someone tries to read beyond the visorchannel size. Signed-off-by:
-
Jes Sorensen authored
Signed-off-by:
-
Jes Sorensen authored
Signed-off-by:
-
Jes Sorensen authored
Signed-off-by:
-
Jes Sorensen authored
Signed-off-by:
-
Jes Sorensen authored
Signed-off-by:
-
