During boot we see a number of these warnings:

vio 30000000: Warning: IOMMU dma not supported: mask 0xffffffffffffffff, table unavailable

The reason for this is that we set IOMMU properties for all VIO
devices even if they are not DMA capable.

Only set DMA ops, table and mask for devices with a DMA window.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

We use SIAR or regs->nip for the instruction pointer depending on
the PMU configuration, but we always use regs->nip in the callchain.

Use perf_instruction_pointer so the backtrace is consistent.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

At the moment we always use the SIAR if the PMU supports continuous
sampling. Unfortunately the SIAR and the PMU exception are not
synchronised for non marked events so we can end up with callchains
that dont make sense.

The following patch checks the HV and PR bits for samples coming from
userspace and always uses pt_regs for them. Userspace will never have
interrupts off so there is no real advantage to using the SIAR for
non marked events in userspace.

I had experimented with a patch that did a similar thing for kernel
samples but we lost a significant amount of information. I was
unable to profile any of our early exception code for example.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The logic to choose whether to use the SIAR or get the information
out of pt_regs is going to get more complicated, so do it once in
perf_read_regs.

We overload regs->result which is gross but we are already doing it
with regs->dsisr.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

We want to access the MMCRA_SIHV and MMCRA_SIPR bits elsewhere so
create mmcra_sihv and mmcra_sipr which hide the differences between
the old and new layout of the bits.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Some macros use RA where when RA=R0 the values is 0, so make this
the enforced mnemonic in the macro.

Idea suggested by Andreas Schwab.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

R0 is special since it'll be 0.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Enforce the use of R0-R31 in macros where possible now we have all the
fixes in.

R0-R31 macros are removed here so that can't be used anymore.  They
should not be defined anywhere.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Now have ___PPC_RA/B/S/T we can use it in some places.  These are
places where we can't use the existing defines which will soon enforce
R0-R31 usage.

The macros being changed here are being used in inline asm, which
can't convert to enforce the R0-R31 usage.

bpf_jit uses a mix of both generated and non-generated with the same
code, so just convert all these to use the ___PPC_R versions which
won't enforce R usage later.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

These are currently the same as __PPC_RA/B/S/T but we'll wrap them
soon.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

We need to do this so we can enforce the name of a and b in called
macros PPC_RA/B later.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

These macros are using integers where they could be using logical
names since they take registers.

We are going to enforce this soon, so fix these up now.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

LOAD_REG_ADDR define is just a wrapper around real instructions so we
can just use real register names here (ie. lower case).
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

mtocrf define is just a wrapper around the real instructions so we can
just use real register names here (ie. lower case).

Also remove braces in macro so this is possible.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Move this duplicated definition to ppc_asm.h and remove the
braces which prevent the use of %rN register names
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Merge the defines of VCPU_GPR from different places.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Merge the defines of STACKFRAMESIZE, STK_REG, STK_PARAM from different
places.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

move lbz/stbciz to ppc-opcode.h.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Now all the fixes are in place, let's rock-n-roll!
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Anything that uses a constructed instruction (ie. from ppc-opcode.h),
need to use the new R0 macro, as %r0 is not going to work.

Also convert usages of macros where we are just determining an offset
(usually for a load/store), like:
	std	r14,STK_REG(r14)(r1)
Can't use STK_REG(r14) as %r14 doesn't work in the STK_REG macro since
it's just calculating an offset.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The assembler doesn't take %r0 register arguments in braces, so remove them.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

We are going to use these later and convert r0 to %r0 etc.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

We want to bring in the latest IRQ fixes

udbg_init_debug_opal() should be udbg_init_debug_opal_raw() as
the caller in arch/powerpc/kernel/udbg.c expects
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Newer gcc are being a bit blind here (it's pretty obvious we don't
reach the code path using the array if we haven't initialized the
pointer) but none of that is performance critical so let's just
silence it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

There was a typo, checking for CONFIG_TRACE_IRQFLAG instead of
CONFIG_TRACE_IRQFLAGS causing some useful debug code to not be
built

This in turns causes a build error on BookE 64-bit due to incorrect
semicolons at the end of a couple of macros, so let's fix that too
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: stable@vger.kernel.org [v3.4]

Looks like we still have issues with pSeries and Cell idle code
vs. the lazy irq state. In fact, the reset fixes that went upstream
are exposing the problem more by causing BUG_ON() to trigger (which
this patch turns into a WARN_ON instead).

We need to be careful when using a variant of low power state that
has the side effect of turning interrupts back on, to properly set
all the SW & lazy state to look as if everything is enabled before
we enter the low power state with MSR:EE off as we will return with
MSR:EE on. If not, we have a discrepancy of state which can cause
things to go very wrong later on.

This patch moves the logic into a helper and uses it from the
pseries and cell idle code. The power4/970 idle code already got
things right (in assembly even !) so I'm not touching it. The power7
"bare metal" idle code is subtly different and correct. Remains PA6T
and some hypervisor based Cell platforms which have questionable
code in there, but they are mostly dead platforms so I'll fix them
when I manage to get final answers from the respective maintainers
about how the low power state actually works on them.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: stable@vger.kernel.org [v3.4]

Pull regulator fix from Mark Brown:
 "A smallish fix for a lock dependency issue which affects a bunch of
  Qualcomm boards that do unusually complicated things with their
  regulators, the API is unlikely to be called by any other system."

* tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: Fix recursive mutex lockdep warning

Don't call v4l2_ctrl_g_ctrl on ctrls which the model cam in question
does not have.
Reported-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[ Taken directly, since Mauro is on vacation ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'virtio-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus

Pull minor virtio-balloon fix from Rusty Russell:
 "Theoretical fix, which greatly simplifies upcoming balloon patches
  which will go in via some vm tree."

* tag 'virtio-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
  virtio-balloon: fix add/get API use

Pull rpmsg fixes from Ohad Ben-Cohen:
 "Fixing two (somewhat rare) endpoint-related race issues, both of which
  were reported by Fernando Guzman Lugo."

* tag 'rpmsg-3.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/rpmsg:
  rpmsg: make sure inflight messages don't invoke just-removed callbacks
  rpmsg: avoid premature deallocation of endpoints

Pull remoteproc fixes from Ohad Ben-Cohen:
 "Two build-related remoteproc fixes for 3.5."

* tag 'remoteproc-3.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc:
  remoteproc: fix missing CONFIG_FW_LOADER configurations
  remoteproc/omap: fix randconfig unmet direct dependencies

Pull hwspinlock fix from Ohad Ben-Cohen:
 "A single hwspinlock core fix for multiple hwspinlock devices
  scenarios, from Shinya Kuribayashi."

* tag 'hwspinlock-3.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/hwspinlock:
  hwspinlock/core: use global ID to register hwspinlocks on multiple devices

Pull IOMMU fixes from Joerg Roedel:
 "The patches fix several issues in the AMD IOMMU driver, the NVidia
  SMMU driver, and the DMA debug code.

  The most important fix for the AMD IOMMU solves a problem with SR-IOV
  devices where virtual functions did not work with IOMMU enabled.  The
  NVidia SMMU patch fixes a possible sleep while spin-lock situation
  (queued the small fix for v3.5, a better but more intrusive fix is
  coming for v3.6).  The DMA debug patches fix a possible data
  corruption issue due to bool vs u32 usage."

* tag 'iommu-fixes-v3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/amd: fix type bug in flush code
  dma-debug: debugfs_create_bool() takes a u32 pointer
  iommu/tegra: smmu: Fix unsleepable memory allocation
  iommu/amd: Initialize dma_ops for hotplug and sriov devices
  iommu/amd: Fix missing iommu_shutdown initialization in passthrough mode

Since ee7cd898 'virtio: expose added
descriptors immediately.', in virtio balloon virtqueue_get_buf might
now run concurrently with virtqueue_kick.  I audited both and this
seems safe in practice but this is not guaranteed by the API.
Additionally, a spurious interrupt might in theory make
virtqueue_get_buf run in parallel with virtqueue_add_buf, which is
racy.

While we might try to protect against spurious callbacks it's
easier to fix the driver: balloon seems to be the only one
(mis)using the API like this, so let's just fix balloon.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (removed unused var)

Pull cgroup fixes from Tejun Heo:
 "The previous cgroup pull request contained a patch to fix a race
  condition during cgroup hierarchy umount.  Unfortunately, while the
  patch reduced the race window such that the test case I and Sasha were
  using didn't trigger it anymore, it wasn't complete - Shyju and Li
  could reliably trigger the race condition using a different test case.

  The problem wasn't the gap between dentry deletion and release which
  the previous patch tried to fix.  The window was between the last
  dput() of a root's child and the resulting dput() of the root.  For
  cgroup dentries, the deletion and release always happen synchronously.
  As this releases the s_active ref, the refcnt of the root dentry,
  which doesn't hold s_active, stays above zero without the
  corresponding s_active.  If umount was in progress, the last
  deactivate_super() proceeds to destory the superblock and triggers
  BUG() on the non-zero root dentry refcnt after shrinking.

  This issue surfaced because cgroup dentries are now allowed to linger
  after rmdir(2) since 3.5-rc1.  Before, rmdir synchronously drained the
  dentry refcnt and the s_active acquired by rmdir from vfs layer
  protected the whole thing.  After 3.5-rc1, cgroup may internally hold
  and put dentry refs after rmdir finishes and the delayed dput()
  doesn't have surrounding s_active ref exposing this issue.

  This pull request contains two patches - one reverting the previous
  incorrect fix and the other adding the surrounding s_active ref around
  the delayed dput().

  This is quite late in the release cycle but the change is on the safer
  side and fixes the test cases reliably, so I don't think it's too
  crazy."

* 'for-3.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: fix cgroup hierarchy umount race
  Revert "cgroup: superblock can't be released with active dentries"

Pull security docs update from James Morris.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  security: Minor improvements to no_new_privs documentation