- 08 Jul, 2020 16 commits
-
-
David S. Miller authored
Michael Chan says: ==================== bnxt_en: Driver update for net-next. This patchset implements ethtool -X to setup user-defined RSS indirection table. The new infrastructure also allows the proper logical ring index to be used to populate the RSS indirection when queried by ethtool -x. Prior to these patches, we were incorrectly populating the output of ethtool -x with internal ring IDs which would make no sense to the user. The last 2 patches add some cleanups to the VLAN acceleration logic and check the firmware capabilities before allowing VLAN acceleration offloads. v4: Move bnxt_get_rxfh_indir_size() fix to a new patch #2. Modify patch #7 to revert RSS map to default only when necessary. v3: Use ALIGN() in patch 5. Add warning messages in patch 6. v2: Some RSS indirection table changes requested by Jakub Kicinski. ==================== Reviewed-by:Jakub Kicinski <kuba@kernel.org> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Edwin Peer authored
Bare-metal use cases require giving firmware and the embedded application processor control over VLAN offloads. The driver should not attempt to override or utilize this feature in such scenarios since it will not work as expected. Signed-off-by:
Edwin Peer <edwin.peer@broadcom.com> Signed-off-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
Edwin Peer authored
The hardware VLAN offload feature on our NIC does not have separate knobs for handling customer and service tags on RX. Either offloading of both must be enabled or both must be disabled. Introduce definitions for the combined feature set in order to clean up the code and make this constraint more clear. Technically these features can be separately enabled on TX, however, since the default is to turn both on, the combined TX feature set is also introduced for code consistency. Signed-off-by:
-
Michael Chan authored
With the new infrastructure in place, we can now support the setting of the indirection table from ethtool. When changing channels, in a rare case that firmware cannot reserve the rings that were promised, we will still try to keep the RSS map and only revert to default when absolutely necessary. v4: Revert RSS map to default during ring change only when absolutely necessary. v3: Add warning messages when firmware cannot reserve the requested RX rings, and when the RSS table entries have to change to default. v2: When changing channels, if the RSS table size changes and RSS map is non-default, return error. Signed-off-by: -
Michael Chan authored
Now that we have the logical indirection table, we can return these proper logical indices directly to ethtool -x instead of the physical IDs. Reported-by:
Jakub Kicinski <kicinski@fb.com> Signed-off-by:
-
Michael Chan authored
Now that we have the logical table, we can fill the HW RSS table using the logical table's entries and converting them to the HW specific format. Re-initialize the logical table to standard distribution if the number of RX rings changes during ring reservation. v4: Use bnxt_get_rxfh_indir_size() to get the RSS table size. v2: Use ALIGN() to roundup the RSS table size. Signed-off-by:
-
Michael Chan authored
On some chips, this varies based on the number of RX rings. Add this helper function and refactor the existing code to use it. Signed-off-by:
-
Michael Chan authored
The driver currently does not keep track of the logical RSS indirection table. The hardware RSS table is set up with standard default ring distribution when initializing the chip. This makes it difficult to support user sepcified indirection table entries. As a first step, add the logical table in the main bnxt structure and allocate it according to chip specific table size. Add a function that sets up default RSS distribution based on the number of RX rings. v4: Use bnxt_get_rxfh_indir_size() for the current RSS table size. v2: Use kmalloc_array() since we init. all entries afterwards. Use ALIGN() to roundup the RSS table size. Use ethtool_rxfh_indir_default() to init. the default entries. Signed-off-by: -
Michael Chan authored
Fix up bnxt_get_rxfh_indir_size() to return the proper current RSS table size for P5 chips. Change it to non-static so that bnxt.c can use it to get the table size. Signed-off-by:
-
Michael Chan authored
Currently, we allocate one page for the hardware DMA RSS indirection table. While the size is currently big enough for all chips, future chip variations may support bigger sizes, so it is better to calculate and store the chip specific size and allocate accordingly. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-nextDavid S. Miller authored
Pablo Neira Ayuso says: ==================== Netfilter/IPVS updates for net-next The following patchset contains Netfilter updates for net-next: 1) Support for rejecting packets from the prerouting chain, from Laura Garcia Liebana. 2) Remove useless assignment in pipapo, from Stefano Brivio. 3) On demand hook registration in IPVS, from Julian Anastasov. 4) Expire IPVS connection from process context to not overload timers, also from Julian. 5) Fallback to conntrack TCP tracker to handle connection reuse in IPVS, from Julian Anastasov. 6) Several patches to support for chain bindings. 7) Expose enum nft_chain_flags through UAPI. 8) Reject unsupported chain flags from the netlink control plane. ==================== Signed-off-by: -
David S. Miller authored
Florian Fainelli says: ==================== net: phy: Uninline PHY ethtool statistics Now that we have introduced ethtool_phy_ops we can uninline those operations and move them back into phy.c where they belong. Since those functions are used by DSA, we need to continue exporting those symbols. It might be possible to remove ndo_get_ethtool_phy_stats in a subsequent patch since we could have DSA register its own ethtool_phy_ops instance instead of overloading the ethtool_ops. ==================== Signed-off-by: -
Florian Fainelli authored
Now that we have moved the PHY ethtool statistics to be dynamically registered, we no longer need to inline those for ethtool. This used to be done to avoid cross symbol referencing and allow ethtool to be decoupled from PHYLIB entirely. Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Florian Fainelli authored
Extend ethtool_phy_ops to include the 3 function pointers necessary for implementing PHY statistics. In a subsequent change we will uninline those functions. Signed-off-by:
-
Alexander A. Klimov authored
Rationale: Reduces attack surface on kernel devs opening the links for MITM as HTTPS traffic is much harder to manipulate. Deterministic algorithm: For each file: If not .svg: For each line: If doesn't contain `\bxmlns\b`: For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`: If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`: If both the HTTP and HTTPS versions return 200 OK and serve the same content: Replace HTTP with HTTPS. Signed-off-by:Alexander A. Klimov <grandmaster@al2klimov.de> Acked-by:
Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by:
-
Florian Fainelli authored
We have a number of error conditions that can lead to the driver not probing successfully, move the print when we are sure dsa_register_switch() has suceeded. This avoids repeated prints in case of probe deferral for instance. Signed-off-by:
Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by:
-
- 07 Jul, 2020 24 commits
-
-
Chris Healy authored
Add error checking with sfp_irq_name before use. Signed-off-by:
Chris Healy <cphealy@gmail.com> Signed-off-by:
-
Gustavo A. R. Silva authored
Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/latest/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-throughSigned-off-by:
Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by:
-
Alexander A. Klimov authored
Rationale: Reduces attack surface on kernel devs opening the links for MITM as HTTPS traffic is much harder to manipulate. Deterministic algorithm: For each file: If not .svg: For each line: If doesn't contain `\bxmlns\b`: For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`: If both the HTTP and HTTPS versions return 200 OK and serve the same content: Replace HTTP with HTTPS. Signed-off-by: -
Alexander A. Klimov authored
Rationale: Reduces attack surface on kernel devs opening the links for MITM as HTTPS traffic is much harder to manipulate. Deterministic algorithm: For each file: If not .svg: For each line: If doesn't contain `\bxmlns\b`: For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`: If both the HTTP and HTTPS versions return 200 OK and serve the same content: Replace HTTP with HTTPS. Signed-off-by: -
Colin Ian King authored
There are spelling mistakes in various literal strings. Fix these. Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
David S. Miller authored
Florian Fainelli says: ==================== net: ethtool: Untangle PHYLIB dependency This patch series untangles the ethtool netlink dependency with PHYLIB which exists because the cable test feature calls directly into PHY library functions. The approach taken here is to introduce ethtool_phy_ops function pointers which can be dynamically registered when PHYLIB loads. ==================== Signed-off-by: -
Florian Fainelli authored
Now that we have introduced ethtool_phy_ops and the PHY library dynamically registers its operations with that function pointer, we can remove the direct PHYLIB dependency in favor of using dynamic operations. Signed-off-by:
-
Florian Fainelli authored
Utilize ethtool_set_ethtool_phy_ops to register a suitable set of PHY ethtool operations in a dynamic fashion such that ethtool will no longer directy reference PHY library symbols. Signed-off-by:
-
Florian Fainelli authored
In order to decouple ethtool from its PHY library dependency, define an ethtool_phy_ops singleton which can be overriden by the PHY library when it loads with an appropriate set of function pointers. Signed-off-by:
-
Randy Dunlap authored
Fix table formatting to eliminate warnings. Documentation/networking/ethtool-netlink.rst:509: WARNING: Malformed table. Documentation/networking/ethtool-netlink.rst:522: WARNING: Malformed table. Documentation/networking/ethtool-netlink.rst:543: WARNING: Malformed table. Documentation/networking/ethtool-netlink.rst:555: WARNING: Malformed table. Documentation/networking/ethtool-netlink.rst:591: WARNING: Malformed table. Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Signed-off-by:
-
Bartosz Golaszewski authored
If phylib is built as a module and CONFIG_MDIO_DEVICE is 'y', the mdio_device and mdio_bus code will be in the phylib module, not in the kernel image. Meanwhile we build mdio_devres depending on the CONFIG_MDIO_DEVICE symbol, so if it's 'y', it will go into the kernel and we'll hit the following linker error: ld: drivers/net/phy/mdio_devres.o: in function `devm_mdiobus_alloc_size': >> drivers/net/phy/mdio_devres.c:38: undefined reference to `mdiobus_alloc_size' ld: drivers/net/phy/mdio_devres.o: in function `devm_mdiobus_free': >> drivers/net/phy/mdio_devres.c:16: undefined reference to `mdiobus_free' ld: drivers/net/phy/mdio_devres.o: in function `__devm_mdiobus_register': >> drivers/net/phy/mdio_devres.c:87: undefined reference to `__mdiobus_register' ld: drivers/net/phy/mdio_devres.o: in function `devm_mdiobus_unregister': >> drivers/net/phy/mdio_devres.c:53: undefined reference to `mdiobus_unregister' ld: drivers/net/phy/mdio_devres.o: in function `devm_of_mdiobus_register': >> drivers/net/phy/mdio_devres.c:120: undefined reference to `of_mdiobus_register' Add a hidden Kconfig option for MDIO_DEVRES which will be currently selected by CONFIG_PHYLIB as there are no non-phylib users of these helpers. Reported-by:
kernel test robot <lkp@intel.com> Fixes: ac3a68d5 ("net: phy: don't abuse devres in devm_mdiobus_register()") Signed-off-by:
Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by:
-
David S. Miller authored
Vaibhav Gupta says: ==================== smsc: use generic power management Linux Kernel Mentee: Remove Legacy Power Management. The purpose of this patch series is to remove legacy power management callbacks from smsc ethernet drivers. The callbacks performing suspend() and resume() operations are still calling pci_save_state(), pci_set_power_state(), etc. and handling the power management themselves, which is not recommended. The conversion requires the removal of the those function calls and change the callback definition accordingly and make use of dev_pm_ops structure. All patches are compile-tested only. V2: Kbuild in V1, warning: variable 'err' is used uninitialized whenever 'if' conditio is false in funcution .resume() . ==================== Signed-off-by: -
Vaibhav Gupta authored
Drivers should not use legacy power management as they have to manage power states and related operations, for the device, themselves. This driver was handling them with the help of PCI helper functions. With generic PM, all essentials will be handled by the PCI core. Driver needs to do only device-specific operations. Compile-tested only. Signed-off-by:
Vaibhav Gupta <vaibhavgupta40@gmail.com> Signed-off-by:
-
Vaibhav Gupta authored
Drivers should not use legacy power management as they have to manage power states and related operations, for the device, themselves. With generic PM, all essentials will be handled by the PCI core. Driver needs to do only device-specific operations. Compile-tested only. Signed-off-by:
-
Matteo Croce authored
priv->page_pool is an array, so comparing against it will always return true. Do a meaningful check by checking priv->page_pool[0] instead. While at it, clear the page_pool pointers on deallocation, or when an allocation error happens during init. Reported-by:
Matteo Croce <mcroce@microsoft.com> Signed-off-by:
-
Florian Westphal authored
We can re-use the existing work queue to handle path management instead of a dedicated work queue. Just move pm_worker to protocol.c, call it from the mptcp worker and get rid of the msk lock (already held). Signed-off-by:
Florian Westphal <fw@strlen.de> Reviewed-by:
Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by:
-
Wei Yongjun authored
In certain configurations without power management support, gcc report the following warning: drivers/net/ethernet/sun/cassini.c:5206:12: warning: 'cas_resume' defined but not used [-Wunused-function] 5206 | static int cas_resume(struct device *dev_d) | ^~~~~~~~~~ Mark cas_resume() as __maybe_unused to make it clear. Fixes: f193f4eb ("sun/cassini: use generic power management") Reported-by:Hulk Robot <hulkci@huawei.com> Signed-off-by:
Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by:
-
Vaibhav Gupta authored
The upgraded .suspend() and .resume() throw "defined but not used [-Wunused-function]" warning for certain configurations. Mark them with "__maybe_unused" attribute. Compile-tested only. Fixes: b0db0cc2 ("sun/niu: use generic power management") Reported-by:
Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by:
-
David S. Miller authored
Andrew Lunn says: ==================== drivers/net/phy C=1 W=1 fixes This fixes most of the Sparse and W=1 warnings in drivers/net/phy. The Cavium code is still not fully clean, but it might actually be the strange code is confusing Sparse. v2 -- Added RB, TB, AB. s/case/cause Reverse Christmas tree Module soft dependencies ==================== Signed-off-by: -
Andrew Lunn authored
To ensure that the octeon MDIO driver has been loaded, the Cavium ethernet drivers reference a dummy symbol in the MDIO driver. This forces it to be loaded first. And this symbol has not been cleanly implemented, resulting in warnings when build W=1 C=1. Since device tree is being used, and a phandle points to the PHY on the MDIO bus, we can make use of deferred probing. If the PHY fails to connect, it should be because the MDIO bus driver has not loaded yet. Return -EPROBE_DEFER so it will be tried again later. Additionally, add a MODULE_SOFTDEP() to give user space a hint as to what order it should load the modules. v2: s/octoen/octeon/ Add MODULE_SOFTDEP() Cc: Sunil Goutham <sgoutham@marvell.com> Cc: Robert Richter <rrichter@marvell.com> Cc: Chris Packham <chris.packham@alliedtelesis.co.nz> Tested-by:
Chris Packham <chris.packham@alliedtelesis.co.nz> Acked-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reviewed-by:
-
Andrew Lunn authored
The MIPS low level register access functions seem to be missing __iomem annotation. This causes lots of sparse warnings, when code casts off the __iomem. Make the Cavium MDIO drivers cleaner by pushing the casts lower down into the helpers, allow the drivers to work as normal, with __iomem. bus->register_base is now an void *, rather than a u64. So forming the mii_bus->id string cannot use %llx any more. Use %px, so this kernel address is still exposed to user space, as it was before. v2: s/cases/causes/g Cc: Sunil Goutham <sgoutham@marvell.com> Cc: Robert Richter <rrichter@marvell.com> Reviewed-by:
-
Andrew Lunn authored
ntohs() expects to be passed a __be16. Correct the type of the variable holding the sequence ID. Cc: Richard Cochran <richardcochran@gmail.com> Acked-by:
Richard Cochran <richardcochran@gmail.com> Reviewed-by:
-
Andrew Lunn authored
This array is not used outside of phy_device.c, so make it static. Reviewed-by:
-
Andrew Lunn authored
Avoid the W=1 warning that symbol 'genphy_c45_driver' was not declared. Should it be static? Declare it on the phy header file. Reviewed-by:
-
