- 21 Jun, 2023 40 commits
-
-
Krzysztof Kozlowski authored
WCN3990 comes with two chains - CH0 and CH1 - where each takes VDD regulator. It seems VDD_CH1 is optional (Linux driver does not care about it), so document it to fix dtbs_check warnings like: sdm850-lenovo-yoga-c630.dtb: bluetooth: 'vddch1-supply' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by:
Conor Dooley <conor.dooley@microchip.com> Link: https://lore.kernel.org/r/20230617165716.279857-1-krzysztof.kozlowski@linaro.orgSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Ravi Gunasekaran authored
When port-to-port forwarding for interfaces in HSR node is enabled, disable promiscuous mode since L2 frame forward happens at the offloaded hardware. Signed-off-by:
Ravi Gunasekaran <r-gunasekaran@ti.com> Reviewed-by:
Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230614114710.31400-1-r-gunasekaran@ti.comSigned-off-by:
-
Jakub Kicinski authored
Christian Marangi says: ==================== leds: trigger: netdev: add additional modes This is a continue of [1]. It was decided to take a more gradual approach to implement LEDs support for switch and phy starting with basic support and then implementing the hw control part when we have all the prereq done. This should be the final part for the netdev trigger. I added net-next tag and added netdev mailing list since I was informed that this should be merged with netdev branch. We collect some info around and we found a good set of modes that are common in almost all the PHY and Switch. These modes are: - Modes for dedicated link speed(10, 100, 1000 mbps). Additional mode can be added later following this example. - Modes for half and full duplex. The original idea was to add hw control only modes. While the concept makes sense in practice it would results in lots of additional code and extra check to make sure we are setting correct modes. With the suggestion from Andrew it was pointed out that using the ethtool APIs we can actually get the current link speed and duplex and this effectively removed the problem of having hw control only modes since we can fallback to software. Since these modes are supported by software, we can skip providing an user for this in the LED driver to support hw control for these new modes (that will come right after this is merged) and prevent this to be another multi subsystem series. For link speed and duplex we use ethtool APIs. To call ethtool APIs, rtnl lock is needed but this can be skipped on handling netdev events as the lock is already held. [1] https://lore.kernel.org/lkml/20230216013230.22978-1-ansuelsmth@gmail.com/ ==================== Link: https://lore.kernel.org/r/20230619204700.6665-1-ansuelsmth@gmail.comSigned-off-by:
-
Christian Marangi authored
Expose hw_control status via sysfs for the netdev trigger to give userspace better understanding of the current state of the trigger and the LED. Signed-off-by:
Christian Marangi <ansuelsmth@gmail.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Reviewed-by:
Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Acked-by:
Lee Jones <lee@kernel.org> Signed-off-by:
-
Christian Marangi authored
Add additional modes for specific link duplex. Use ethtool APIs to get the current link duplex and enable the LED accordingly. Under netdev event handler the rtnl lock is already held and is not needed to be set to access ethtool APIs. This is especially useful for PHY and Switch that supports LEDs hw control for specific link duplex. Add additional modes: - half_duplex: Turn on LED when link is half duplex - full_duplex: Turn on LED when link is full duplex Signed-off-by:
-
Christian Marangi authored
Add additional modes for specific link speed. Use ethtool APIs to get the current link speed and enable the LED accordingly. Under netdev event handler the rtnl lock is already held and is not needed to be set to access ethtool APIs. This is especially useful for PHY and Switch that supports LEDs hw control for specific link speed. (example scenario a PHY that have 2 LED connected one green and one orange where the green is turned on with 1000mbps speed and orange is turned on with 10mpbs speed) On mode set from sysfs we check if we have enabled split link speed mode and reject enabling generic link mode to prevent wrong and redundant configuration. Rework logic on the set baseline state to support these new modes to select if we need to turn on or off the LED. Add additional modes: - link_10: Turn on LED when link speed is 10mbps - link_100: Turn on LED when link speed is 100mbps - link_1000: Turn on LED when link speed is 1000mbps Signed-off-by:
-
Ivan Vecera authored
Link VF representors to parent PCI device to benefit from systemd defined naming scheme. Without this change the representor is visible as ethN. Signed-off-by:
Ivan Vecera <ivecera@redhat.com> Reviewed-by:
Michael Chan <michael.chan@broadcom.com> Link: https://lore.kernel.org/r/20230620144855.288443-1-ivecera@redhat.comSigned-off-by:
-
Jakub Kicinski authored
Petr Machata says: ==================== selftests: Preparations for out-of-order-operations patches in mlxsw The mlxsw driver currently makes the assumption that the user applies configuration in a bottom-up manner. Thus netdevices need to be added to the bridge before IP addresses are configured on that bridge or SVI added on top of it. Enslaving a netdevice to another netdevice that already has uppers is in fact forbidden by mlxsw for this reason. Despite this safety, it is rather easy to get into situations where the offloaded configuration is just plain wrong. Over the course of the following several patchsets, mlxsw code is going to be adjusted to diminish the space of wrongly offloaded configurations. Ideally the offload state will reflect the actual state, regardless of the sequence of operation used to construct that state. Several selftests build configurations that will not be offloadable in the future on some systems. The reason is that what will get offloaded is the actual configuration, not the configuration steps. For example, when a port is added to a bridge that has an IP address, that bridge will get a RIF, which it would not have with the current code. But on Nvidia Spectrum-1 machines, MAC addresses of all RIFs need to have the same prefix, which the bridge will violate. The RIF thus couldn't be created, and the enslavement is therefore canceled, because it would lead to an unoffloadable configuration. This breaks some selftests. In this patchset, adjust selftests to avoid the configurations that mlxsw would be incapable of offloading, while maintaining relevance with regards to the feature that is being tested. There are generally two cases of fixes: - Disabling IPv6 autogen on bridges that do not participate in routing, either because of the abovementioned requirement to keep the same MAC prefix on all in-HW router interfaces, or, on 802.1ad bridges, because in-HW router interfaces are not supported at all. - Setting the bridge MAC address to what it will become after the first member port is attached, so that the in-HW router interface is created with a supported MAC address. The patchset is then split thus: - Patches #1-#7 adjust generic selftests - Patches #8-#16 adjust mlxsw-specific selftests ==================== Link: https://lore.kernel.org/r/cover.1687265905.git.petrm@nvidia.comSigned-off-by:
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. At the time that the front panel port is enslaved to the bridge, the bridge MAC address does not have the same prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all the RIFs have to have the same 38-bit MAC address prefix. Since the bridge does not obey this limitation, the RIF cannot be created, and the enslavement attempt is vetoed on the grounds of the configuration not being offloadable. The bridge eventually inherits MAC address from its first member, after the enslavement is acked. A number of (mainly VXLAN) selftests already work around the problem by setting the MAC address to whatever it will eventually be anyway. Do the same for this selftest. Signed-off-by:
Petr Machata <petrm@nvidia.com> Reviewed-by:
Danielle Ratson <danieller@nvidia.com> Signed-off-by:
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. At the time that the front panel port is enslaved to the bridge (this holds for all bridges used here), the bridge MAC address does not have the same prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all the RIFs have to have the same 38-bit MAC address prefix. Since the bridge does not obey this limitation, the RIF cannot be created, and the enslavement attempt is vetoed on the grounds of the configuration not being offloadable. The selftest itself however checks various aspects of VXLAN offloading and the bridges do not need to participate in routing traffic. The IP addresses or the RIFs are irrelevant. Fix by disabling automatic IPv6 address generation for the HW-offloaded bridges in this selftest, thus exempting them from mlxsw router attention. Signed-off-by:
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. At the time that the front panel port is enslaved to the bridge, the bridge MAC address does not have the same prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all the RIFs have to have the same 38-bit MAC address prefix. Since the bridge does not obey this limitation, the RIF cannot be created, and the enslavement attempt is vetoed on the grounds of the configuration not being offloadable. The selftest itself however checks vetoing of a different aspect of the configuration and the bridge does not need to participate in routing traffic. The IP address or the RIF are irrelevant. Fix by disabling automatic IPv6 address generation for the HW-offloaded bridge in this selftest, thus exempting it from mlxsw router attention. Signed-off-by:
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. At the time that the front panel port is enslaved to the bridge (this holds for both bridges used here), the bridge MAC address does not have the same prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all the RIFs have to have the same 38-bit MAC address prefix. Since the bridge does not obey this limitation, the RIF cannot be created, and the enslavement attempt is vetoed on the grounds of the configuration not being offloadable. The selftest itself however checks traffic prioritization and scheduling, and the bridges serve for their L2 forwarding capabilities, and do not need to participate in routing traffic. The IP addresses or the RIFs are irrelevant. Fix by disabling automatic IPv6 address generation for the HW-offloaded bridges in this selftest, thus exempting them from mlxsw router attention. Signed-off-by:
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. At the time that the front panel port is enslaved to the bridge (this holds for both bridges used here), the bridge MAC address does not have the same prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all the RIFs have to have the same 38-bit MAC address prefix. Since the bridge does not obey this limitation, the RIF cannot be created, and the enslavement attempt is vetoed on the grounds of the configuration not being offloadable. The selftest itself however checks traffic prioritization and scheduling, and the bridges serve for their L2 forwarding capabilities, and do not need to participate in routing traffic. The IP addresses or the RIFs are irrelevant. Fix by disabling automatic IPv6 address generation for the HW-offloaded bridges in this selftest, thus exempting them from mlxsw router attention. Signed-off-by:
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. At the time that the front panel port is enslaved to the bridge, the bridge MAC address does not have the same prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all the RIFs have to have the same 38-bit MAC address prefix. Since the bridge does not obey this limitation, the RIF cannot be created, and the enslavement attempt is vetoed on the grounds of the configuration not being offloadable. The selftest itself however checks DCB DSCP-based prioritization, and the bridge serves for its L2 forwarding capabilities, and does not need to participate in routing traffic. The IP address or the RIF are irrelevant. Fix by disabling automatic IPv6 address generation for the HW-offloaded bridge in this selftest, thus exempting it from mlxsw router attention. Signed-off-by:
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. At the time that the front panel port is enslaved to the bridge, the bridge MAC address does not have the same prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all the RIFs have to have the same 38-bit MAC address prefix. Since the bridge does not obey this limitation, the RIF cannot be created, and the enslavement attempt is vetoed on the grounds of the configuration not being offloadable. The selftest itself however checks how many mirroring sessions a machine is capable of offloading. The IP address or the RIF are irrelevant. Fix by disabling automatic IPv6 address generation for the HW-offloaded bridge in this selftest, thus exempting it from mlxsw router attention. Signed-off-by:
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. At the time that the front panel port is enslaved to the bridge (this holds for all bridges used here), the bridge MAC address does not have the same prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all the RIFs have to have the same 38-bit MAC address prefix. Since the bridge does not obey this limitation, the RIF cannot be created, and the enslavement attempt is vetoed on the grounds of the configuration not being offloadable. The selftest itself however checks whether a different vetoed aspect of the configuration provides an extack. The IP address or the RIF are irrelevant. Fix by disabling automatic IPv6 address generation for the HW-offloaded bridges in this selftest, thus exempting them from mlxsw router attention. Signed-off-by:
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. The swp enslavement to the 802.1ad bridge is not allowed, because RIFs are not allowed to be created for 802.1ad bridges, but the address indicates one needs to be created. Thus the veto selftests fail already during the port enslavement. Then the attempt to create a VLAN on top of the same bridge is not vetoed, because the bridge is not related to mlxsw, and the selftest fails. Fix by disabling automatic IPv6 address generation for the bridges in this selftest, thus exempting them from the mlxsw router attention. Signed-off-by:
Amit Cohen <amcohen@nvidia.com> Signed-off-by:
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. At the time that the front panel port is enslaved to the bridge, the bridge MAC address does not have the same prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all the RIFs have to have the same 38-bit MAC address prefix. Since the bridge does not obey this limitation, the RIF cannot be created, and the enslavement attempt is vetoed on the grounds of the configuration not being offloadable. The bridge eventually inherits MAC address from its first member, after the enslavement is acked. A number of (mainly VXLAN) selftests already work around the problem by setting the MAC address to whatever it will eventually be anyway. Do the same here. Signed-off-by:
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. At the time that the front panel port is enslaved to the bridge, the bridge MAC address does not have the same prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all the RIFs have to have the same 38-bit MAC address prefix. Since the bridge does not obey this limitation, the RIF cannot be created, and the enslavement attempt is vetoed on the grounds of the configuration not being offloadable. The bridge eventually inherits MAC address from its first member, after the enslavement is acked. A number of (mainly VXLAN) selftests already work around the problem by setting the MAC address to whatever it will eventually be anyway. Do the same for several mirror_gre selftests. Signed-off-by:
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. At the time that the front panel port is enslaved to the bridge, the bridge MAC address does not have the same prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all the RIFs have to have the same 38-bit MAC address prefix. Since the bridge does not obey this limitation, the RIF cannot be created, and the enslavement attempt is vetoed on the grounds of the configuration not being offloadable. These two selftests however check mirroring traffic to a gretap netdevice. The bridge here does not participate in routing traffic and the IP address or the RIF are irrelevant. Fix by disabling automatic IPv6 address generation for the HW-offloaded bridges in these selftests, thus exempting them from mlxsw router attention. Since the bridges are only used for L2 forwarding, this change should not hinder usefulness of this selftest for testing SW datapath or HW datapaths in other devices. Signed-off-by:
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. At the time that the front panel port is enslaved to the bridge, the bridge MAC address does not have the same prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all the RIFs have to have the same 38-bit MAC address prefix. Since the bridge does not obey this limitation, the RIF cannot be created, and the enslavement attempt is vetoed on the grounds of the configuration not being offloadable. The selftest itself however checks whether skbedit changes packet priority as appropriate. The bridge thus does not need to participate in routing traffic and the IP address or the RIF are irrelevant. Fix by disabling automatic IPv6 address generation for the HW-offloaded bridge in this selftest, thus exempting it from mlxsw router attention. Since the bridge is only used for L2 forwarding, this change should not hinder usefulness of this selftest for testing SW datapath or HW datapaths in other devices. Signed-off-by:
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. At the time that the front panel port is enslaved to the bridge, the bridge MAC address does not have the same prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all the RIFs have to have the same 38-bit MAC address prefix. Since the bridge does not obey this limitation, the RIF cannot be created, and the enslavement attempt is vetoed on the grounds of the configuration not being offloadable. The selftest itself however checks operation of pedit on IPv4 and IPv6 dsfield and its parts. The bridge thus does not need to participate in routing traffic and the IP address or the RIF are irrelevant. Fix by disabling automatic IPv6 address generation for the HW-offloaded bridge in this selftest, thus exempting it from mlxsw router attention. Since the bridge is only used for L2 forwarding, this change should not hinder usefulness of this selftest for testing SW datapath or HW datapaths in other devices. Signed-off-by:
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. This will cause this selftest to fail spuriously. The swp enslavement to the 802.1ad bridge is not allowed, because RIFs are not allowed to be created for 802.1ad bridges, but the address indicates one needs to be created. Fix by disabling automatic IPv6 address generation for the HW-offloaded bridge in this selftest, thus exempting it from mlxsw router attention. Signed-off-by:
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. This will cause this selftest to fail spuriously. The swp enslavement to the 802.1ad bridge is not allowed, because RIFs are not allowed to be created for 802.1ad bridges, but the address indicates one needs to be created. Fix by disabling automatic IPv6 address generation for the HW-offloaded bridge in this selftest, thus exempting it from mlxsw router attention. Signed-off-by:
-
Horatiu Vultur authored
Currently for each timestamp frame, the SW needs to go and read the received timestamp over the MDIO bus. But the HW has the capability to store the received nanoseconds part and the least significant two bits of the seconds in the reserved field of the PTP header. In this way we could save few MDIO transactions (actually a little more transactions because the access to the PTP registers are indirect) for each received frame. Instead of reading the rest of seconds part of the timestamp of the frame using MDIO transactions schedule PTP worker thread to read the seconds part every 500ms and then for each of the received frames use this information. Because if for example running with 512 frames per second, there is no point to read 512 times the second part. Doing all these changes will give a great CPU usage performance. Running ptp4l with logSyncInterval of -9 will give a ~60% CPU improvement. Signed-off-by:
Horatiu Vultur <horatiu.vultur@microchip.com> Acked-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jakub Kicinski authored
Bartosz Golaszewski says: ==================== net: stmmac: dwmac-qcom-ethqos: add support for EMAC4 Extend the dwmac-qcom-ethqos driver to support EMAC4. While at it: rework the code somewhat. The bindings have been reviewed by DT maintainers. This is a sub-series of [1] with only the patches targetting the net subsystem as they can go in independently. [1] https://lore.kernel.org/lkml/20230617001644.4e093326@kernel.org/T/ ==================== Link: https://lore.kernel.org/r/20230619092402.195578-1-brgl@bgdev.plSigned-off-by:
-
Bartosz Golaszewski authored
sa8775p uses EMAC version 4, add the relevant defines, rename the has_emac3 switch to has_emac_ge_3 (has emac greater-or-equal than 3) and add the new compatible. Signed-off-by:
Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by:
-
Bartosz Golaszewski authored
Add the compatible for the MAC controller on sa8775p platforms. This MAC works with a single interrupt so add minItems to the interrupts property. The fourth clock's name is different here so change it. Enable relevant PHY properties. Add the relevant compatibles to the binding document for snps,dwmac as well. Signed-off-by:
-
Bartosz Golaszewski authored
On some platforms, the PCS can be integrated in the MAC so the driver will not see any PCS link activity. Add a switch that allows the platform drivers to let the core code know. Signed-off-by:
Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by:
-
Bartosz Golaszewski authored
On sa8775p the MAC is connected to the external PHY over SGMII so add support for it to the driver. Signed-off-by:
-
Bartosz Golaszewski authored
In preparation for supporting SGMII, let's make the code a bit more generic. Add a new callback for MAC configuration so that we can assign a different variant of it in the future. Signed-off-by:
Andrew Halaney <ahalaney@redhat.com> Signed-off-by:
-
Bartosz Golaszewski authored
On sa8775p, the EMAC revision is 4 and we use SGMII instead of RGMII. There's no "rgmii" clock but there's a fourth clock under a different name: "phyaux". Add a new field to the chip data struct that specifies the link clock name. Default to "rgmii" for backward compatibility. Signed-off-by:
-
Bartosz Golaszewski authored
On sa8775p platforms, there's a SGMII SerDes PHY between the MAC and external PHY that we need to enable and configure. Signed-off-by:
-
Bartosz Golaszewski authored
There's an unnecessary space in the rgmii_updatel() function, remove it. Signed-off-by:
-
Bartosz Golaszewski authored
Typically we use a newline between global and local headers so add it here as well. Signed-off-by:
-
Bartosz Golaszewski authored
device_get_phy_mode() is declared in linux/property.h but this header is not included. Signed-off-by:
-
Bartosz Golaszewski authored
Shrink code and avoid line breaks by using a helper variable for &pdev->dev. Signed-off-by:
-
Bartosz Golaszewski authored
Make sure we follow the reverse-xmas tree convention. Signed-off-by:
-
Bartosz Golaszewski authored
The err_mem label's name is unclear. It actually should be reached on any error after stmmac_probe_config_dt() succeeds. Name it after the cleanup action that needs to be called before exiting. Signed-off-by:
-
Bartosz Golaszewski authored
We can use a devm action to completely drop the remove callback and use stmmac_pltfr_remove() directly for remove. We can also drop one of the goto labels. Signed-off-by:
-
