- 21 Mar, 2018 40 commits
-
-
Jacopo Mondi authored
Remove soc_camera framework dependencies from mt9t112 sensor driver. - Handle clk, gpios and power routines - Register async subdev - Remove deprecated g/s_mbus_config operations - Remove driver flags - Change driver interface and add kernel doc - Adjust build system - Fix code style issues reported by checkpatch in strict mode This commit does not remove the original soc_camera based driver as long as other platforms depends on soc_camera framework. As I don't have access to a working camera module, this change has only been compile tested. Signed-off-by:
Jacopo Mondi <jacopo+renesas@jmondi.org> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com>
-
Jacopo Mondi authored
Copy the soc_camera based driver in v4l2 sensor driver directory. This commit just copies the original file without modifying it. No modification to KConfig and Makefile as soc_camera framework dependencies need to be removed first in next commit. Signed-off-by:
-
Antti Palosaari authored
Correct coding style issues reported mostly by checkpatch.pl. Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
-
Antti Palosaari authored
Use regmap for chip register access. Signed-off-by:
-
Antti Palosaari authored
Add probe and disconnect callbacks that behaves similarly than ones used commonly on Linux driver model. We need those to get early / late access to driver in order to use normal probe time stuff, like regmap, extra bus adapters and so. Signed-off-by:
-
Antti Palosaari authored
Replace static stream settings by one which enables and disables stream interface when needed (TS streaming control). 1) Configure both TS IF and USB endpoints according to current use case 2) Disable streaming USB endpoints when streaming is stopped and enable when streaming is started. Reduces sleep power consumption slightly. 3) Reduce USB buffersize slightly, from 130848 to 98136 bytes Signed-off-by:
-
Antti Palosaari authored
Small improvements. Signed-off-by:
-
Antti Palosaari authored
Small revise, no functional changes. Signed-off-by:
-
Antti Palosaari authored
PID filters are moved to af9013 demod driver as those are property of demod. As pid filters are now implemented correctly by demod driver, we could enable pid filter support for possible slave demod too on dual tuner configuration. Signed-off-by:
-
Antti Palosaari authored
af9013 demod has pid filter. Add support for it. Signed-off-by:
-
Antti Palosaari authored
No one is binding that driver through media attach so remove it and all related dead code. Signed-off-by:
-
Antti Palosaari authored
af9013 demod driver has i2c binding. Use it. Signed-off-by:
-
Antti Palosaari authored
Add muxed i2c adapter for demod tuner i2c bus gate control. Signed-off-by:
-
Antti Palosaari authored
Convert inttabs to format (reg, mask, val) which are suitable parameters to pass directly for regmap_update_bits. Signed-off-by:
-
Antti Palosaari authored
Pass correct device to dev_* logging functions, which allows us to remove redundant KBUILD_MODNAME and __func__ parameters from log format. Signed-off-by:
-
Antti Palosaari authored
Driver has calculated dvbv5 statistics, so use those as a base for legacy dvbv3 statistics. Wrap and convert needed values to dvbv3, remove old dvbv3 statistic implementations. Signed-off-by:
-
Antti Palosaari authored
Implement dvbv5 ber and per. Signed-off-by:
-
Antti Palosaari authored
Implement dvbv5 cnr. Signed-off-by:
-
Antti Palosaari authored
Implement dvbv5 signal strength estimate. We know tuner dependent -80dBm and -50dBm agc values, construct line equation and use it to map agc value to signal strength estimate. Signed-off-by:
-
Antti Palosaari authored
Whilst rewritten largely, the basic logic remains same with one exception: do not return immediately on success case. We are going to add statistics that function and cannot return too early. Signed-off-by:
-
Sean Young authored
This mceusb does not need the carrier count quirk, with it set it reports the carrier higher than it is. Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
-
A Sun authored
media: mceusb: add IR learning support features (IR carrier frequency measurement and wide-band/short-range receiver) Windows Media Center IR transceivers include two IR receivers; wide-band/short-range and narrow-band/long-range. The short-range (5cm distance) receiver is for IR learning and has IR carrier frequency measuring ability. Add mceusb driver support to select the short range IR receiver and enable pass through of its IR carrier frequency measurements. RC and LIRC already support these mceusb driver additions. Test platform: Linux raspberrypi 4.9.59-v7+ #1047 SMP Sun Oct 29 12:19:23 GMT 2017 armv7l GNU/Linux mceusb 1-1.2:1.0: Registered Pinnacle Systems PCTV Remote USB with mce emulator interface version 1 mceusb 1-1.2:1.0: 2 tx ports (0x0 cabled) and 2 rx sensors (0x1 active) Sony TV remote control ir-ctl from v4l-utils pi@raspberrypi:~ $ ir-ctl -V IR raw version 1.12.3 pi@raspberrypi:~ $ ir-ctl -m -r ... pulse 650 space 550 pulse 650 space 600 pulse 600 space 600 pulse 1200 space 600 pulse 650 space 550 pulse 650 space 600 pulse 600 space 600 pulse 550 carrier 40004 space 16777215 ^C pi@raspberrypi:~ $ exit Signed-off-by:
A Sun <as1033x@comcast.net> Signed-off-by:
-
Sean Young authored
A timeout of 200ms is much longer than necessary, and delays the decoding decoding of a single scancode and the last scancode when a button is being held. This makes the remote seem sluggish. If the min_timeout and max_timeout values are set, the timeout is configurable via the LIRC_SET_REC_TIMEOUT ioctl. Tested-by:
Matthias Reichl <hias@horus.com> Signed-off-by:
-
Sean Young authored
Meson doesn't seem to be able to generate timeout events in hardware. So install a software timer to generate the timeout events required by the decoders to prevent "ghost keypresses". Reported-by:
-
Johan Hovold authored
Drop bogus call to usb_driver_release_interface() from the disconnect() callback. As the interface is already being unbound at this point, usb_driver_release_interface() simply returns early. Signed-off-by:
Johan Hovold <johan@kernel.org> Reviewed-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Philipp Zabel authored
The IPUv3 code has 8-bit grayscale capture support. Enable imx-media to use it. Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
-
Jean-Michel Hautbois authored
The ADV7604 has thirteen 256-byte maps that can be accessed via the main I2C ports. Each map has it own I2C address and acts as a standard slave device on the I2C bus. Allow a device tree node to override the default addresses so that address conflicts with other devices on the same bus may be resolved at the board description level. [Kieran: Re-adapted for mainline] Signed-off-by:
Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com> Signed-off-by:
Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Jean-Michel Hautbois authored
The ADV7604 has thirteen 256-byte maps that can be accessed via the main I2C ports. Each map has it own I2C address and acts as a standard slave device on the I2C bus. Extend the device tree node bindings to be able to override the default addresses so that address conflicts with other devices on the same bus may be resolved at the board description level. [Kieran: Re-adapted for mainline] Signed-off-by:
Rob Herring <robh@kernel.org> Reviewed-by:
-
Kieran Bingham authored
The ADV748x has twelve 256-byte maps that can be accessed via the main I2C ports. Each map has it own I2C address and acts as a standard slave device on the I2C bus. Allow a device tree node to override the default addresses so that address conflicts with other devices on the same bus may be resolved at the board description level. Signed-off-by:
Kieran Bingham <kieran.bingham@ideasonboard.com> Reviewed-by:
Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by:
-
Kieran Bingham authored
The ADV748x has 12 pages mapped onto I2C addresses. In the existing implementation only 11 are mapped correctly in the page enumerations, which causes an off-by-one fault on pages above the infoframe definition due to a missing 'CBUS' page. This causes the address for the CEC, SDP, TXA, and TXB to be incorrectly programmed during the iterations in adv748x_initialise_clients(). Until now this has gone un-noticed due to the fact that following the creation of the clients - the device is reset and the addresses are reprogrammed in manually by the call to "adv748x_write_regs(state, adv748x_set_slave_address);" As part of moving to dynamic i2c address allocations repair this by providing the missing CBUS page definition. Signed-off-by:
-
Kieran Bingham authored
The ADV748x has identical map configurations for each register map. The duplication of each map can be simplified using a helper macro such that each map is represented on a single line. Define ADV748X_REGMAP_CONF for this purpose use it to create the tables. Signed-off-by:
-
Hans Verkuil authored
The v4l2_subdev core s_power op was used for two different things: power on/off sensors or video decoders/encoders and to put a tuner in standby (and only the tuner!). There is no 'tuner wakeup' op, that's done automatically when the tuner is accessed. The danger with calling (s_power, 0) to put a tuner into standby is that it is usually broadcast for all subdevs. So a video receiver subdev that supports s_power will also be powered off, and since there is no corresponding (s_power, 1) they will never be powered on again. In addition, this is specifically meant for tuners only since they draw the most current. This patch adds a new tuner op called 'standby' and replaces all calls to (core, s_power, 0) by (tuner, standby). This prevents confusion between the two uses of s_power. Note that there is no overlap: bridge drivers either just want to put the tuner into standby, or they deal with powering on/off sensors. Never both. This also makes it easier to replace s_power for the remaining bridge drivers with some PM code later. Whether we want something cleaner for tuners in the future is a separate topic. There is a lot of legacy code surrounding tuners, and I am very hesitant about making changes there. Signed-off-by:
-
Luca Ceresoli authored
Driver writers can benefit in knowing if/when callbacks are called in interrupt context. But it is not completely obvious here, so document it. Signed-off-by:
Luca Ceresoli <luca@lucaceresoli.net> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Pawel Osciak <pawel@osciak.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by:
-
Luca Ceresoli authored
VB2_BUF_STATE_REQUEUEING is accepted by vb2_buffer_done() but not documented, so add it along with notes about calls in interrupt context. Signed-off-by:
-
Luca Ceresoli authored
Documentation about what start_streaming() should do on failure are scattered in two places and mostly duplicated, so consolidate them in one of the two places. Signed-off-by:
-
Douglas Fischer authored
Fixed si470x_start() disabling the interrupt signal, causing tune operations to never complete. This does not affect USB radios because they poll the registers instead of using the IRQ line. Signed-off-by:
Douglas Fischer <fischerdouglasc@gmail.com> [hans.verkuil@cisco.com: fixed 80 column checkpatch warning] Signed-off-by:
-
Douglas Fischer authored
Added the call to v4l2_device_register() required to add a new radio device. Without this patch, it is impossible for the driver to load. This does not affect USB devices. Signed-off-by:
-
Douglas Fischer authored
Fixed si470x_set_channel() trying to tune before chip is turned on, which causes warnings in dmesg and when probing, makes driver wait for 3s for tuning timeout. This issue did not affect USB devices because they have a different probing sequence. Signed-off-by:
-
Hugues Fruchet authored
Add DCMI JPEG support. Signed-off-by:
Hugues Fruchet <hugues.fruchet@st.com> Signed-off-by:
-
Hugues Fruchet authored
Fix unnecessary parentheses in if conditions. Detected by checkpatch.pl --strict. Signed-off-by:
-
