- 12 Apr, 2022 40 commits
-
-
Bhupesh Sharma authored
Fix the following 'make dtbs_check' warning(s) by using phy@ instead of lanes@ and by moving '#clock-cells' to sub-node: arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dt.yaml: ssphy@78000: 'lane@78200' does not match any of the regexes: '^phy@[0-9a-f]+$', 'pinctrl-[0-9]+' Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Rob Herring <robh@kernel.org> Signed-off-by:
Bhupesh Sharma <bhupesh.sharma@linaro.org> Reviewed-by:
Shawn Guo <shawn.guo@linaro.org> [bjorn: s/clock-names/clock-cells/ per Shawn's feedback] Signed-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220228123019.382037-7-bhupesh.sharma@linaro.org
-
Bhupesh Sharma authored
Fix the 'make dtbs_check' warning: arch/arm64/boot/dts/qcom/sm8450-qrd.dt.yaml: phy@1d87000: 'lanes@1d87400' does not match any of the regexes: '^phy@[0-9a-f]+$', 'pinctrl-[0-9]+' Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Rob Herring <robh@kernel.org> Signed-off-by:
-
Bhupesh Sharma authored
Fix the 'make dtbs_check' warning: arch/arm64/boot/dts/qcom/sc7280-idp.dt.yaml: phy@1c0e000: 'lanes@1c0e200' does not match any of the regexes: '^phy@[0-9a-f]+$', 'pinctrl-[0-9]+' Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Rob Herring <robh@kernel.org> Signed-off-by:
-
Bhupesh Sharma authored
The following properties are not supported and causing dtbs_check warnings. - vdda-phy-max-microamp - vdda-pll-max-microamp - vddp-ref-clk-max-microamp - vddp-ref-clk-always-on arch/arm64/boot/dts/qcom/msm8996-xiaomi-gemini.dt.yaml: phy@627000: 'vdda-phy-max-microamp', 'vddp-ref-clk-always-on', 'vddp-ref-clk-max-microamp' do not match any of the regexes: '^phy@[0-9a-f]+$', 'pinctrl-[0-9]+' Drop them from QMP PHY nodes for 'msm8996-xiaomi' dts. Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Rob Herring <robh+dt@kernel.org> Signed-off-by: -
Stephan Gerhold authored
The BAM Data Multiplexer provides access to the network data channels of modems integrated into many older Qualcomm SoCs, including MSM8916. Add the nodes for the BAM DMA engine and BAM-DMUX to enable using WWAN on smartphones/tablets based on MSM8916. This should work out of the box with open-source WWAN userspace such as ModemManager. The nodes are disabled by default to avoid loading unnecessary drivers on devices that cannot use BAM-DMUX (e.g. DragonBoard 410c). However, strictly speaking the nodes could be enabled by default since both the bam_dma and bam_dmux driver will simply do nothing if the modem does not announce any BAM-DMUX channels. Signed-off-by:
Stephan Gerhold <stephan@gerhold.net> Signed-off-by:
-
Dmitry Baryshkov authored
Add PM8450 PMIC device tree include file. It is going to be used by SM8450-based devices. Signed-off-by:
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by:
-
Dmitry Baryshkov authored
Most of SoC device trees do not provide the thermal_zones label. Thus stop depending on it and use the full path to the thermal zones nodes. Fixes: 7a3544e5 ("arm64: dts: qcom: pmr735a: Add temp-alarm support") Signed-off-by:
-
Dmitry Baryshkov authored
Most of SoC device trees do not provide the thermal_zones label. Thus stop depending on it and use the full path to the thermal zones nodes. Fixes: 3795fe7d ("arm64: dts: qcom: pm8350c: Add temp-alarm support") Signed-off-by:
-
Dmitry Baryshkov authored
Add temp-alarm device tree node and a default configuration for the corresponding thermal zone for this PMIC. Temperatures are based on downstream values. Signed-off-by:
-
Dmitry Baryshkov authored
Add temp-alarm device tree node and a default configuration for the corresponding thermal zone for this PMIC. Temperatures are based on downstream values. Signed-off-by:
-
Dmitry Baryshkov authored
Add temp-alarm device tree node and a default configuration for the corresponding thermal zone for this PMIC. Temperatures are based on downstream values. Signed-off-by:
-
Baruch Siach authored
The IPQ60xx has the same MDIO bug block as IPQ4019. Add IO range and clock resources description. Reviewed-by:
Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by:
Baruch Siach <baruch.siach@siklu.com> Signed-off-by:
-
Jami Kettunen authored
The OnePlus 5/5T both have an NXP PN553 which is supported by the nxp-nci-i2c driver in mainline. It detects/reads NFC tags using "nfctool" and with the NearD test scripts data can also be written to be received by another device. Signed-off-by:
Jami Kettunen <jami.kettunen@somainline.org> Reviewed-by:
Caleb Connolly <caleb@connolly.tech> Signed-off-by:
-
Sankeerth Billakanti authored
Rename the edp_out label in the sc7280 platform to mdss_edp_out so that the nodes related to mdss are all grouped together in the board specific files. Signed-off-by:
Sankeerth Billakanti <quic_sbillaka@quicinc.com> Reviewed-by:
Douglas Anderson <dianders@chromium.org> Reviewed-by:
Stephen Boyd <swboyd@chromium.org> Signed-off-by:
-
Vinod Koul authored
Enable the ethernet node, add the phy node and pinctrl for ethernet. [bhsharma: Correct ethernet/rgmii related pinmuxs, specify multi-queues and plug in the PHY interrupt for WOL] Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by:
Vinod Koul <vkoul@kernel.org> Signed-off-by:
-
Vinod Koul authored
SM8150 SoC supports ethqos ethernet controller so add the node for it Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by:
-
Luca Weiss authored
Configure and enable the nodes for UFS that are used for internal storage on FP4. Signed-off-by:
Luca Weiss <luca.weiss@fairphone.com> Signed-off-by:
-
Luca Weiss authored
Add the necessary nodes for UFS and its PHY. Signed-off-by:
Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by:
-
Dmitry Baryshkov authored
Following sm8150/sm8250 update sdm845 capacity-dmips-mhz and dynamic-power-coefficient based on the measurements [1], [2]. The energy model dynamic-power-coefficient values were calculated with DPC = µW / MHz / V^2 for each OPP, and averaged across all OPPs within each cluster for the final coefficient. Voltages were obtained from the qcom-cpufreq-hw driver that reads voltages from the OSM LUT programmed into the SoC. Normalized DMIPS/MHz capacity scale values for each CPU were calculated from CoreMarks/MHz (CoreMark iterations per second per MHz), which serves the same purpose. For each CPU, the final capacity-dmips-mhz value is the C/MHz value of its maximum frequency normalized to SCHED_CAPACITY_SCALE (1024) for the fastest CPU in the system. For more details on measurement process see the commit message for the commit 6aabed55 ("arm64: dts: qcom: sm8250: Add CPU capacities and energy model"). [1] https://github.com/kdrag0n/freqbench [2] https://github.com/kdrag0n/freqbench/tree/master/results/sdm845/main Cc: Danny Lin <danny@kdrag0n.dev> Signed-off-by: -
Bhupesh Sharma authored
Several wakeup gpios supported by the Top Level Mode Multiplexer (TLMM) block on sm8150 can be used as interrupt sources and these interrupts are routed to the PDC interrupt controller. So, specify PDC as the interrupt parent for the TLMM block. Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Vinod Koul <vkoul@kernel.org> Cc: Rob Herring <robh@kernel.org> Signed-off-by:
-
Dmitry Baryshkov authored
Add fastrpc device tree nodes for aDSP, cDSP and SLPI. Signed-off-by:
-
Dmitry Baryshkov authored
Enable the audio, compute, sensor and modem remoteproc and specify firmware path for these on the Qualcomm SM8450 HDK. Signed-off-by:
-
Dmitry Baryshkov authored
On MSM8996 PCI controller bindings are not compatible with snps,dw-pcie binding. The platform doesn't provide second (global) IRQ, it requires additional glue code. To prevent it from probing against the dw-pcie driver, remove corresponding compatible. Fixes: ed965ef8 ("arm64: dts: qcom: msm8996: add support to pcie") Signed-off-by:
-
Dmitry Baryshkov authored
On SDM845 PCI controller bindings are not compatible with snps,dw-pcie binding. The platform doesn't provide second (global) IRQ, it requires additional glue code. To prevent it from probing against the dw-pcie driver, remove corresponding compatible. Fixes: 5c538e09 ("arm64: dts: qcom: sdm845: Add first PCIe controller and PHY") Fixes: 42ad2313 ("arm64: dts: qcom: sdm845: Add second PCIe PHY and controller") Signed-off-by:
-
Dmitry Baryshkov authored
APQ8096 provides a 'modem' with reduced functionality, mainly targeting location services. Enable corresponding device tree node. Signed-off-by:
-
Yassine Oudjana authored
Enable mss_pil and slpi_pil and set their firmware paths. Signed-off-by:
Yassine Oudjana <y.oudjana@protonmail.com> Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> #db820c Signed-off-by:
-
Yassine Oudjana authored
Add nodes for the MSS and SLPI remoteprocs. Signed-off-by:
-
Yassine Oudjana authored
Rename smp2p-modem to smp2p-mpss, and make the subnode labels of smp2p_adsp and smp2p_slpi follow the <name>_smp2p_<out/in> layout. Also move smp2p_slpi_out above smp2p_slpi_in to make it match mpss and adsp where master-kernel is the first subnode. This patch brings no functional change. Signed-off-by:
-
Yassine Oudjana authored
Fix a total overlap between zap_shader_region and slpi_region, and rename all regions to match the naming convention in other Qualcomm SoC device trees. Signed-off-by:
-
Bhupesh Sharma authored
Add support for uSD card on SA8155p-ADP board using the SDHC2 interface. Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Rob Herring <robh@kernel.org> Signed-off-by:
-
Bhupesh Sharma authored
Add support for SDC2 which can be used to interface uSD card. Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Rob Herring <robh@kernel.org> Signed-off-by:
-
Dmitry Baryshkov authored
Dragonboard845c doesn't have board-specific board-id programmed, it uses generic 0xff. Thus add the property with the 'variant' of the calibration data. Note: the driver will check for the calibration data for the following IDs, so older board-2.bin files that were distributed as a part of Linaro releases will continue to work. - 'bus=snoc,qmi-board-id=ff,qmi-chip-id=30214,variant=Thundercomm_DB845C' - 'bus=snoc,qmi-board-id=ff,qmi-chip-id=30214' - 'bus=snoc,qmi-board-id=ff' For the reference, the board is identified by the driver in the following way: ath10k_snoc 18800000.wifi: qmi chip_id 0x30214 chip_family 0x4001 board_id 0xff soc_id 0x40030001 ath10k_snoc 18800000.wifi: qmi fw_version 0x2009856b fw_build_timestamp 2018-07-19 12:28 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1 Fixes: 3f72e2d3 ("arm64: dts: qcom: Add Dragonboard 845c") Signed-off-by:
-
Krzysztof Kozlowski authored
The DT schema expects clocks core-iface order. No functional change. Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
-
Krzysztof Kozlowski authored
The DT schema expects dma channels in tx-rx order. No functional change. Signed-off-by:
-
Krzysztof Kozlowski authored
The "bluetooth" is more popular and more descriptive than "bt", for a Bluetooth device. The WCNSS DT schema will expect such naming. Signed-off-by:
-
Souradeep Chowdhury authored
Set the default dr_mode for usb2 node to "otg" to enable role-switch for EUD(Embedded USB Debugger) connector node. Signed-off-by:
Souradeep Chowdhury <quic_schowdhu@quicinc.com> Signed-off-by:
-
Manikanta Pubbisetty authored
Add DTS node for WCN6750 WiFi chipset. Signed-off-by:
Manikanta Pubbisetty <quic_mpubbise@quicinc.com> Reviewed-by:
Matthias Kaehlcke <mka@chromium.org> Signed-off-by:
-
Krzysztof Kozlowski authored
ref_clk clock in UFS node is already there with a <0 0> frequency, which matches other DTSI files. Signed-off-by:
-
Krzysztof Kozlowski authored
The Qualcomm UFS bindings require to use specific (qcom,msm8996-ufshc) and generic (jedec,ufs-2.0) compatibles. Signed-off-by:
-
Krzysztof Kozlowski authored
The property vddp-ref-clk-max-microamp (for VDDP ref clk supply which is l25 regulator) is not documented in MSM8996 UFS PHY bindings (qcom,msm8996-qmp-ufs-phy). It is mentioned in the other UFS PHY bindings for qcom,msm8996-ufs-phy-qmp-14nm. The MSM8996-based Xiaomi devices configure l25 regulator in a conflicting way: 1. with maximum 100 uAmp for VDDP ref clk supply of UFS PHY, 2. with maximum 450 mAmp for VCCQ supply of UFS. Since the vddp-ref-clk-max-microamp property is basically not documented for that UFS PHY and has a conflicting values, drop it entirely as it looks like not tested and not used ever. Signed-off-by:
-
