IT8628E is functionally identical to IT8620E.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Several of the chips supported by this driver have a configuration
register to enable fan4 and fan5. Use those registers to determine
if fan4 and fan5 tachometers are supported.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

On/Off mode is only supported for pwm controls 0-2, and not supported at all for
IT8603E/IT8623E. For pwm controls 3-6 and for IT8603E/IT8623E, SmartGuardian mode
is always enabled. Use it and set the pwm value to the maximum if fan control
is disabled.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Fix various checkpatch complaints to clean up the code and
make it easier to read.

CHECK: Do not include the paragraph about writing to the FSF
CHECK: Alignment should match open parenthesis
CHECK: Logical continuations should be on the previous line
CHECK: No space is necessary after a cast
CHECK: Please don't use multiple blank lines
CHECK: Please use a blank line after function/struct/union/enum
       declarations
CHECK: spaces preferred around that '+' (ctx:VxV)
WARNING: Missing a blank line after declarations

No functional change.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Using array size defines makes it much easier to find errors
in index values and loop counts.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Using the BIT macro makes the code a little easier to read and has the
added benefit of making checkpatch happy.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

IT8620E supports three additional voltage sensors.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Voltage registers are non-sequential. Use a register array instead
of a macro to map sensor index to register to simplify the code
and to make it easier to add additional voltage sensors.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Add support for the additional temperature sensors on IT8620E.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Convert to use devm_hwmon_device_register_with_groups to simplify
code and reduce code size. This also attaches sysfs attributes
to the hwmon device and no longer to the platform device.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Use is_visible to determine if attributes should be generated or not.
This simplifies the code and reduces object size by about 120 bytes
on x86_64.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Simplify code and reduce object size by about 250 bytes on x86_64.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Simplify code and reduce object size by almost 500 bytes on x86_64.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Simplify code and reduce object size by more than 200 bytes on x86_64.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Simplify code and reduce object size by more than 300 bytes on x86_64.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Cleanup only, no functional change.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

The Super-IO chip can also reside at SIO address 0x4e, and there can be
two Super-IO chips in the system. Add support for it.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

This will let us support more than one chip on different SIO addresses
with the same driver.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Using the same varible name for function names and as static
variable invites misuse and prevents us from adding support
for a second chip. Rename pdev to it87_pdev and limit its use
to where it is needed.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Return directly on errors if there is no cleanup necessary.
Don't create an error message on memory allocation errors.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Recent chips have a separate register to select the pwm2 frequency.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

IT8620E supports up to 6 pwm channels. Add support for it.
Also check if fan tachometers 4..6 are enabled before instantiating
the respective sysfs attributes.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

AVCC3 is supported on IT8620E, similar to IT8603E. Add feature flag
to indicate AVCC3 support. Don't enable it for now on IT8620E since
it is unclear if this chip supports it correctly.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Signed-off-by: Guenter Roeck <linux@roeck-us.net>

This patch adds a platform check function to make code more readable.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

This patch adds the description to explain the TDP reporting mechanism
and accumulated power algorithm.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Cc: Borislav Petkov <bp@alien8.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

This patch introduces an algorithm that computes the average power by
reading a delta value of “core power accumulator” register during
measurement interval, and then dividing delta value by the length of
the time interval.

User is able to use power1_average entry to measure the processor power
consumption and power1_average_interval entry to set the interval.

A simple example:

ray@hr-ub:~/tip$ sensors
fam15h_power-pci-00c4
Adapter: PCI adapter
power1:       19.58 mW (avg =   2.55 mW, interval =   0.01 s)
                       (crit =  15.00 W)

...

The result is current average processor power consumption in 10
millisecond. The unit of the result is uWatt.
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Cc: Borislav Petkov <bp@alien8.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

PTSC is the performance timestamp counter value in a cpu core and the
cores in one compute unit have the fixed frequency. So it picks up the
performance timestamp counter value of the first core per compute unit
to measure the interval for average power per compute unit.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Cc: Borislav Petkov <bp@alien8.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

This patch adds a member in fam15h_power_data which specifies the
compute unit accumulated power. It adds do_read_registers_on_cu to do
all the read to all MSRs and run it on one of the online cores on each
compute unit with smp_call_function_many(). This behavior can decrease
IPI numbers.
Suggested-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

This patch adds CONFIG_CPU_SUP_AMD as the dependence of fam15h_power
driver. Because the following patch will use the interface from
x86/kernel/cpu/amd.c.

Otherwise, the below error might be encountered:

All errors (new ones prefixed by >>):

   drivers/built-in.o: In function `fam15h_power_probe':
>> fam15h_power.c:(.text+0x26e3a3): undefined reference to
>> `amd_get_cores_per_cu'
   fam15h_power.c:(.text+0x26e41e): undefined reference to
`amd_get_cores_per_cu'
Reported-by: build test robot <lkp@intel.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Add basic support for the Maxim Integrated MAX31722/MAX31723 SPI
temperature sensors / thermostats.

Includes:
    - ACPI support;
    - raw temperature readings;
    - power management

Datasheet:
https://datasheets.maximintegrated.com/en/ds/MAX31722-MAX31723.pdfSigned-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

On ads7828 the internal reference defaults to off upon power up. When
using internal reference, it needs to be turned on and the voltage needs
to settle before normal conversion cycle can be started. Hence perform a
dummy read in the probe to enable the internal reference allowing the
voltage to settle before performing a normal read.

Without this fix, the first read from the ADC when using internal
reference always returns incorrect data.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Pull perf fixes from Ingo Molnar:
 "Misc kernel side fixes:

   - fix event leak
   - fix AMD PMU driver bug
   - fix core event handling bug
   - fix build bug on certain randconfigs

  Plus misc tooling fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/amd/ibs: Fix pmu::stop() nesting
  perf/core: Don't leak event in the syscall error path
  perf/core: Fix time tracking bug with multiplexing
  perf jit: genelf makes assumptions about endian
  perf hists: Fix determination of a callchain node's childlessness
  perf tools: Add missing initialization of perf_sample.cpumode in synthesized samples
  perf tools: Fix build break on powerpc
  perf/x86: Move events_sysfs_show() outside CPU_SUP_INTEL
  perf bench: Fix detached tarball building due to missing 'perf bench memcpy' headers
  perf tests: Fix tarpkg build test error output redirection

Pull core kernel fixes from Ingo Molnar:
 "This contains the nohz/atomic cleanup/fix for the fetch_or() ugliness
  you noted during the original nohz pull request, plus there's also
  misc fixes:

   - fix liblockdep build bug
   - fix uapi header build bug
   - print more lockdep hash collision info to help debug recent reports
     of hash collisions
   - update MAINTAINERS email address"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  MAINTAINERS: Update my email address
  locking/lockdep: Print chain_key collision information
  uapi/linux/stddef.h: Provide __always_inline to userspace headers
  tools/lib/lockdep: Fix unsupported 'basename -s' in run_tests.sh
  locking/atomic, sched: Unexport fetch_or()
  timers/nohz: Convert tick dependency mask to atomic_t
  locking/atomic: Introduce atomic_fetch_or()

Commit 840f5b05 ("media: au0828 disable tuner to demod link in
au0828_media_device_register()") removed all uses of the 'dtv_demod',
but left the variable itself around.

Remove it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull x86 fixes from Thomas Gleixner:
 "This lot contains:

   - Some fixups for the fallout of the topology consolidation which
     unearthed AMD/Intel inconsistencies
   - Documentation for the x86 topology management
   - Support for AMD advanced power management bits
   - Two simple cleanups removing duplicated code"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpu: Add advanced power management bits
  x86/thread_info: Merge two !__ASSEMBLY__ sections
  x86/cpufreq: Remove duplicated TDP MSR macro definitions
  x86/Documentation: Start documenting x86 topology
  x86/cpu: Get rid of compute_unit_id
  perf/x86/amd: Cleanup Fam10h NB event constraints
  x86/topology: Fix AMD core count

Pull remoteproc fix from Bjorn Andersson:
 "Fix incorrect error check in the ST remoteproc driver and advertise
  the newly created linux-remoteproc mailing list"

* tag 'rproc-v4.6-rc1' of git://github.com/andersson/remoteproc:
  MAINTAINERS: Add mailing list for remote processor subsystems
  remoteproc: st: fix check of syscon_regmap_lookup_by_phandle() return value