- 03 Jan, 2023 14 commits
-
-
Tvrtko Ursulin authored
Replace the deprecated macro with the per-device one. Signed-off-by:
Tvrtko Ursulin <tvrtko.ursulin@intel.com> Acked-by:
Christian König <christian.koenig@amd.com> Reviewed-by:
Simon Ser <contact@emersion.fr> Signed-off-by:
-
Thomas Zimmermann authored
Drivers only emulate XRGB8888 framebuffers. Remove all conversion helpers that do not use XRGB8888 as their source format. Also remove some special cases for alpha formats in the blit helper. Signed-off-by:
Thomas Zimmermann <tzimmermann@suse.de> Reviewed-by:
Javier Martinez Canillas <javierm@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230102112927.26565-14-tzimmermann@suse.de
-
Thomas Zimmermann authored
The DRM helper drm_fb_build_fourcc_list() creates a list of color formats for primary planes of the generic drivers. Simplify the helper: - It used to mix and filter native and emulated formats as provided by the driver. Now the only emulated format is XRGB8888, which is required as fallback by legacy software. Drop support for emulating any other formats. - Also convert alpha formats to their non-alpha counterparts. Generic drivers don't support primary planes with alpha formats and some DTs incorrectly advertise alpha channels for non-alpha hardware. So only export non-alpha formats for primary planes. With the simplified helper, scrap format lists of the affected generic drivers. All they need is the firmware buffer's native format, from which the helper creates the list of color formats. Signed-off-by:
-
Thomas Zimmermann authored
Fix the color-format selection of the single-probe helper. Go through all user-specified values and test each for compatibility with the driver. If none is supported, use the driver-provided default. This guarantees that the console is always available in any color format at least. Until now, the format selection of the single-probe helper tried to either use a user-specified format or a 32-bit default format. If the user-specified format was not supported by the driver, the selection failed and the display remained blank. Signed-off-by:
-
Thomas Zimmermann authored
Split the single-probe helper's implementation into multiple functions and get locking and overallocation out of the way of the surface setup. Simplifies later changes to the setup code. Signed-off-by:
-
Thomas Zimmermann authored
Add conversion from XRGB8888 to XRGB1555, ARGB1555 and RGBA5551, which are the formats currently supported by the simplefb infrastructure. The new helpers allow the output of XRGB8888 framebuffers to firmware scanout buffers in one of the 15-bit formats. v3: * use __le* for destination buffers (Jose, kernel test robot) v2: * test 15-bit results with local endianness (Jose) Signed-off-by:
José Expósito <jose.exposito89@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230102112927.26565-10-tzimmermann@suse.de
-
Thomas Zimmermann authored
Add dedicated helper to convert from XRGB8888 to ARGB2101010. Sets all alpha bits to make pixels fully opaque. v2: * set correct format in struct drm_framebuffer (Javier) * use cpubuf_to_le32() * type fixes Signed-off-by:
-
Thomas Zimmermann authored
Add dedicated helper to convert from XRGB8888 to ARGB8888. Sets all alpha bits to make pixels fully opaque. v3: * use __le32 for destination buffer (Jose, kernel test robot) v2: * use cpubuf_to_le32() * type fixes Signed-off-by:
-
Thomas Zimmermann authored
Upcoming changes to the format conversion will mostly blit from XRGB8888 to some other format. So put the source format in blit's outer branches to make the code more readable. For cases where a format only changes its endianness, such as XRGB565, introduce dedicated branches that handle this for all formats. Signed-off-by:
-
Thomas Zimmermann authored
Change the source-buffer type of le32buf_to_cpu() to __le32* to reflect endianness. Result buffers are converted to local endianness, so instantiate them from regular u8 or u32 types. Signed-off-by:
Maíra Canal <mcanal@igalia.com> Reviewed-by:
-
Thomas Zimmermann authored
Fix to-RGB565 conversion helpers to store the result in little- endian byte order. Update test cases as well. Signed-off-by:
-
Thomas Zimmermann authored
Convert test input for format helpers from host byte order to little-endian order. The current code does it the other way around, but there's no effective difference to the result. Signed-off-by:
-
Thomas Zimmermann authored
RGB888 is different than the other formats as most of its pixels are unaligned and therefore helper functions do not use endianness conversion helpers. Comment on this in the source code. Signed-off-by:
-
Thomas Zimmermann authored
Select color format for EFI/VESA firmware scanout buffer from the number of bits per pixel and the position of the individual color components. Fixes the selected format for the buffer in several odd cases. For example, XRGB1555 has been reported as ARGB1555 because of the different use of depth and transparency in VESA and Linux. Bits-per-pixel is always the pixel's raw number of bits; including alpha and filler bits. It is preferred over color depth, which has a different meaning among various components and standards. Also do not compare reserved bits and transparency bits to each other. These values have different meanings, as reserved bits include filler bits while transparency does not. Signed-off-by:
-
- 02 Jan, 2023 5 commits
-
-
Rob Clark authored
Add a sequence # for more easily matching up cmd/resp, and the # of free slots in the virtqueue to more easily see starvation issues. v2: Fix handling of string fields as well Signed-off-by:
Rob Clark <robdclark@chromium.org> Reviewed-by:
Dmitry Osipenko <dmitry.osipenko@collabora.com> Signed-off-by:
-
Dave Stevenson authored
Commit 5ea6b170 ("drm/panel: Add prepare_prev_first flag to drm_panel") added code to copy prepare_prev_first from drm_panel to pre_enable_prev_first in drm_bridge when called through devm_panel_bridge_add, but missed drmm_panel_bridge_add. Add the same code to drmm_panel_bridge_add. Fixes: 5ea6b170 ("drm/panel: Add prepare_prev_first flag to drm_panel") Signed-off-by:
Dave Stevenson <dave.stevenson@raspberrypi.com> Reviewed-by:
Jagan Teki <jagan@amarulasolutions.com> Signed-off-by:
Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20221222185213.3773336-1-dave.stevenson@raspberrypi.com
-
Maíra Canal authored
If vc4_hdmi_reset_link() returns -EDEADLK, it means that a deadlock happened in the locking context. This situation should be addressed by dropping all currently held locks and block until the contended lock becomes available. Currently, vc4 is not dealing with the deadlock properly, producing the following output when PROVE_LOCKING is enabled: [ 825.612809] ------------[ cut here ]------------ [ 825.612852] WARNING: CPU: 1 PID: 116 at drivers/gpu/drm/drm_modeset_lock.c:276 drm_modeset_drop_locks+0x60/0x68 [drm] [ 825.613458] Modules linked in: 8021q mrp garp stp llc raspberrypi_cpufreq brcmfmac brcmutil crct10dif_ce hci_uart cfg80211 btqca btbcm bluetooth vc4 raspberrypi_hwmon snd_soc_hdmi_codec cec clk_raspberrypi ecdh_generic drm_display_helper ecc rfkill drm_dma_helper drm_kms_helper pwm_bcm2835 bcm2835_thermal bcm2835_rng rng_core i2c_bcm2835 drm fuse ip_tables x_tables ipv6 [ 825.613735] CPU: 1 PID: 116 Comm: kworker/1:2 Tainted: G W 6.1.0-rc6-01399-g941aae32 #3 [ 825.613759] Hardware name: Raspberry Pi 3 Model B Rev 1.2 (DT) [ 825.613777] Workqueue: events output_poll_execute [drm_kms_helper] [ 825.614038] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 825.614063] pc : drm_modeset_drop_locks+0x60/0x68 [drm] [ 825.614603] lr : drm_helper_probe_detect+0x120/0x1b4 [drm_kms_helper] [ 825.614829] sp : ffff800008313bf0 [ 825.614844] x29: ffff800008313bf0 x28: ffffcd7778b8b000 x27: 0000000000000000 [ 825.614883] x26: 0000000000000001 x25: 0000000000000001 x24: ffff677cc35c2758 [ 825.614920] x23: ffffcd7707d01430 x22: ffffcd7707c3edc7 x21: 0000000000000001 [ 825.614958] x20: 0000000000000000 x19: ffff800008313c10 x18: 000000000000b6d3 [ 825.614995] x17: ffffcd777835e214 x16: ffffcd7777cef870 x15: fffff81000000000 [ 825.615033] x14: 0000000000000000 x13: 0000000000000099 x12: 0000000000000002 [ 825.615070] x11: 72917988020af800 x10: 72917988020af800 x9 : 72917988020af800 [ 825.615108] x8 : ffff677cc665e0a8 x7 : d00a8c180000110c x6 : ffffcd77774c0054 [ 825.615145] x5 : 0000000000000000 x4 : 0000000000000001 x3 : 0000000000000000 [ 825.615181] x2 : ffff677cc55e1880 x1 : ffffcd7777cef8ec x0 : ffff800008313c10 [ 825.615219] Call trace: [ 825.615232] drm_modeset_drop_locks+0x60/0x68 [drm] [ 825.615773] drm_helper_probe_detect+0x120/0x1b4 [drm_kms_helper] [ 825.616003] output_poll_execute+0xe4/0x224 [drm_kms_helper] [ 825.616233] process_one_work+0x2b4/0x618 [ 825.616264] worker_thread+0x24c/0x464 [ 825.616288] kthread+0xec/0x110 [ 825.616310] ret_from_fork+0x10/0x20 [ 825.616335] irq event stamp: 7634 [ 825.616349] hardirqs last enabled at (7633): [<ffffcd777831ee90>] _raw_spin_unlock_irq+0x3c/0x78 [ 825.616384] hardirqs last disabled at (7634): [<ffffcd7778315a78>] __schedule+0x134/0x9f0 [ 825.616411] softirqs last enabled at (7630): [<ffffcd7707aacea0>] local_bh_enable+0x4/0x30 [ipv6] [ 825.617019] softirqs last disabled at (7618): [<ffffcd7707aace70>] local_bh_disable+0x4/0x30 [ipv6] [ 825.617586] ---[ end trace 0000000000000000 ]--- Therefore, deal with the deadlock as suggested by [1], using the function drm_modeset_backoff(). [1] https://docs.kernel.org/gpu/drm-kms.html?highlight=kms#kms-locking Fixes: 6bed2ea3 ("drm/vc4: hdmi: Reset link on hotplug") Reported-by:
Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by:
-
Carlo Caione authored
The pixel data for the ILI9486 is always 16-bits wide and it must be sent over the SPI bus. When the controller is only able to deal with 8-bit transfers, this 16-bits data needs to be swapped before the sending to account for the big endian bus, this is on the contrary not needed when the SPI controller already supports 16-bits transfers. The decision about swapping the pixel data or not is taken in the MIPI DBI code by probing the controller capabilities: if the controller only suppors 8-bit transfers the data is swapped, otherwise it is not. This swapping/non-swapping is relying on the assumption that when the controller does support 16-bit transactions then the data is sent unswapped in 16-bits-per-word over SPI. The problem with the ILI9486 driver is that it is forcing 8-bit transactions also for controllers supporting 16-bits, violating the assumption and corrupting the pixel data. Align the driver to what is done in the MIPI DBI code by adjusting the transfer size to the maximum allowed by the SPI controller. Reviewed-by:
Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by:
Carlo Caione <ccaione@baylibre.com> Reviewed-by:
Kamlesh Gurudasani <kamlesh.gurudasani@gmail.com> Signed-off-by:
-
Carlo Caione authored
SPI devices use the spi_device_id for module autoloading even on systems using device tree. Add the spi_device_id entry to enable autoloading for the 3.5inch RPi Display (rpi-lcd-35 and piscreen). Reviewed-by:
-
- 29 Dec, 2022 2 commits
-
-
Christophe Branchereau authored
Add bindings for the Forcaltech gpt3, which is a 640x480 3.0" 4:3 IPS LCD Panel found in the YLM/Anbernic RG300X handheld. Signed-off-by:
Christophe Branchereau <cbranchereau@gmail.com> Reviewed-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20221219195233.375637-3-cbranchereau@gmail.com
-
Christophe Branchereau authored
Add the orisetech ota5601a ic driver For now it only supports the focaltech gpt3 3" 640x480 ips panel found in the ylm rg300x handheld. Signed-off-by:
-
- 22 Dec, 2022 7 commits
-
-
Maíra Canal authored
The structs drm_debugfs_info and drm_debugfs_entry introduced a new debugfs structure to DRM, centered on drm_device instead of drm_minor. Therefore, remove the tasks related to create a new device-centered debugfs structure and add a new task to replace the use of drm_debugfs_create_files() for the use of drm_debugfs_add_file() and drm_debugfs_add_files(). Signed-off-by:
Melissa Wen <mwen@igalia.com> Acked-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
Maíra Canal <mairacanal@riseup.net> Link: https://patchwork.freedesktop.org/patch/msgid/20221219120621.15086-8-mcanal@igalia.com
-
Maíra Canal authored
Replace the use of drm_debugfs_create_files() with the new drm_debugfs_add_files() function, which centers the debugfs files management on the drm_device instead of drm_minor. Moreover, remove the debugfs_init hook and add the debugfs files directly on vkms_create(), before drm_dev_register(). Signed-off-by:
-
Maíra Canal authored
Replace the use of drm_debugfs_create_files() with the new drm_debugfs_add_files() function, which centers the debugfs files management on the drm_device instead of drm_minor. Signed-off-by:
-
Maíra Canal authored
Currently, vc4 has its own debugfs infrastructure that adds the debugfs files on drm_dev_register(). With the introduction of the new debugfs, functions, replace the vc4 debugfs structure with the DRM debugfs device-centered function, drm_debugfs_add_file(). Moreover, remove the explicit error handling of debugfs related functions, considering that the only failure mode is -ENOMEM and also that error handling is not recommended for debugfs functions, as pointed out in [1]. [1] https://lore.kernel.org/all/YWAmZdRwnAt6wh9B@kroah.com/Signed-off-by:
-
Maíra Canal authored
Although the device-centered debugfs functions can track requests for the addition of DRM debugfs files at any time and have them added all at once during drm_dev_register(), they are not able to create debugfs files for modeset components, as they are registered after the primary and the render drm_minor are registered. So, create a drm_debugfs_late_register() function, which is responsible for dealing with the creation of all the debugfs files for modeset components at once. Therefore, the functions drm_debugfs_add_file() and drm_debugfs_add_files() can be used in late_register hooks. Signed-off-by:
-
Maíra Canal authored
Replace the use of drm_debugfs_create_files() with the new drm_debugfs_add_files() function in all DRM core files, centering the debugfs files management on the drm_device instead of drm_minor. Signed-off-by:
-
Maíra Canal authored
Introduce the ability to track requests for the addition of DRM debugfs files at any time and have them added all at once during drm_dev_register(). Drivers can add DRM debugfs files to a device-managed list and, during drm_dev_register(), all added files will be created at once. Now, the drivers can use the functions drm_debugfs_add_file() and drm_debugfs_add_files() to create DRM debugfs files instead of using the drm_debugfs_create_files() function. Co-developed-by:
Wambui Karuga <wambui.karugax@gmail.com> Signed-off-by:
-
- 20 Dec, 2022 3 commits
-
-
Thomas Zimmermann authored
Ast hardware scans out the primary plane from video memory, which is in I/O-memory space. Hence init the damage handler's iosys_map pointer as I/O memory. Not all platforms support accessing I/O memory as system memory, although it's usually not a problem in ast's x86-based systems. The error report is at [1]. Reported-by:
kernel test robot <lkp@intel.com> Signed-off-by:
Jocelyn Falempe <jfalempe@redhat.com> Fixes: f2fa5a99 ("drm/ast: Convert ast to SHMEM") Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: Jocelyn Falempe <jfalempe@redhat.com> Cc: Dave Airlie <airlied@redhat.com> Cc: dri-devel@lists.freedesktop.org Link: https://lore.kernel.org/lkml/202212170111.eInM0unS-lkp@intel.com/T/#u # 1 Link: https://patchwork.freedesktop.org/patch/msgid/20221216193005.30280-1-tzimmermann@suse.de
-
Deepak R Varma authored
A call to platform_get_irq() already prints an error on failure within its own implementation. So printing another error based on its return value in the caller is redundant and should be removed. The clean up also makes if condition block braces unnecessary. Remove that as well. Issue identified using platform_get_irq.cocci coccicheck script. Signed-off-by:
Deepak R Varma <drv@mailo.com> Reviewed-by:
-
Uwe Kleine-König authored
There is a local variable that contains dev->driver. Make use of it instead of "open coding" it. Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by:
-
- 19 Dec, 2022 3 commits
-
-
Christian König authored
TTM is just wrapping core DMA functionality here, remove the mid-layer. No functional change. Signed-off-by:
Dave Airlie <airlied@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221125102137.1801-6-christian.koenig@amd.com
-
Melissa Wen authored
As v3d_lookup_bos() performs the same steps as drm_gem_objects_lookup(), replace the explicit code in v3d to simply use the DRM function. Signed-off-by:
Melissa Wen <melissa.srw@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221205135538.3545051-3-mwen@igalia.com
-
Melissa Wen authored
When v3d_lookup_bos fails to `allocate validated BO pointers`, job->bo_count was already set to args->bo_count, but job->bo points to NULL. In this scenario, we must verify that job->bo is not NULL before iterating on it to proper clean up a job. Also, drm_gem_object_put already checks that the object passed is not NULL, doing the job->bo[i] checker redundant. Signed-off-by:
-
- 16 Dec, 2022 6 commits
-
-
Lucas Stach authored
The IPUv3 and DCSS driver are two totally separate DRM drivers. Having one of them live in the drivers/gpu/drm/imx toplevel directory and the other one in the dcss/ subdirectory is confusing. Move the IPUv3 driver into its own subdirectory to make the separation more clear. Signed-off-by:
Lucas Stach <l.stach@pengutronix.de> Reviewed-by:
Philipp Zabel <p.zabel@pengutronix.de> Link: https://lore.kernel.org/r/20221125112519.3849636-1-l.stach@pengutronix.deSigned-off-by:
-
Philipp Zabel authored
ipu_src_rect_width() was introduced to support odd screen resolutions such as 1366x768 by internally rounding up primary plane width to a multiple of 8 and compensating with reduced horizontal blanking. This also caused overlay plane width to be rounded up, which was not intended. Fix overlay plane width by limiting the rounding up to the primary plane. drm_rect_width(&new_state->src) >> 16 is the same value as drm_rect_width(dst) because there is no plane scaling support. Fixes: 94dfec48 ("drm/imx: Add 8 pixel alignment fix") Reviewed-by:
-
Liang He authored
In ipu_add_client_devices(), we need to call of_node_put() for reference returned by of_graph_get_port_by_id() in fail path. Fixes: 17e05217 ("gpu: ipu-v3: Do not bail out on missing optional port nodes") Signed-off-by:
Liang He <windhl@126.com> Reviewed-by:
-
Tomi Valkeinen authored
dsi_dump_dsi_irqs(), a function used for debugfs prints, has a large struct in its frame, which can result in: drivers/gpu/drm/omapdrm/dss/dsi.c:1126:1: warning: the frame size of 1060 bytes is larger than 1024 bytes [-Wframe-larger-than=] As the performance of the function is of no concern, let's allocate the struct with kmalloc instead. Compile-tested only. Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Reported-by:
Arnd Bergmann <arnd@arndb.de> Link: https://patchwork.freedesktop.org/patch/msgid/20220916082206.167427-1-tomi.valkeinen@ideasonboard.com
-
Yuan Can authored
After commit 64ff1891, struct csc_coef_rgb2yuv is not used any more and can be removed as well. Fixes: 64ff1891 ("drm/omap: Enable COLOR_ENCODING and COLOR_RANGE properties for planes") Signed-off-by:
Yuan Can <yuancan@huawei.com> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Randolph Sapp authored
There was a long-standing bug from a typo that created 2 ARGB1555 and ABGR1555 pixel format entries. Weston 10 has a sanity check that alerted me to this issue. According to the Supported Pixel Data formats table we have the later entries should have been for Alpha-X instead. Signed-off-by:
Randolph Sapp <rs@ti.com> Fixes: 32a1795f ("drm/tidss: New driver for TI Keystone platform Display SubSystem") Reviewed-by:
Aradhya Bhatia <a-bhatia1@ti.com> Acked-by:
Andrew Davis <afd@ti.com> Signed-off-by:
-
