The CONFIRM_RKEY LLC processing handles all links in one LLC message.
Move the call to this processing out of smcr_link_reg_rmb() which does
processing per link, into smcr_lgr_reg_rmbs() which is responsible for
link group level processing. Move smcr_link_reg_rmb() into module
smc_core.c.
>From af_smc.c now call smcr_lgr_reg_rmbs() to register new rmbs on all
available links.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Po Liu says:

====================
Introduce a flow gate control action and apply IEEE

Changes from V4:
----------------
0001:
Fix and modify according to Vlid Buslov suggestions:
- Change spin_lock_bh() to spin_lock() since tcf_gate_act() already in
software irq.
- Remove spin lock protect in the ops->cleanup function.
- Enable the CONFIG_DEBUG_ATOMIC_SLEEP and CONFIG_PROVE_LOCKING checking,
then fix as kzalloc flag type and lock deadlock.
- Change kzalloc() flag type from GFP_KERNEL to GFP_ATOMIC since
function in the spin_lock protect.
- Change hrtimer type from HRTIMER_MODE_ABS to HRTIMER_MODE_ABS_SOFT
to avoid deadlock.

0002:
Fix and modify according to Vlid Buslov suggestions:
- Remove all rcu_read_lock protection since no rcu parameters.
- Enable the CONFIG_DEBUG_ATOMIC_SLEEP and CONFIG_PROVE_LOCKING checking,
then check kzalloc sleeping flag.
- Change kzalloc to kcalloc for array memory alloc and change GFP_KERNEL
flag to GFP_ATOMIC since function holding spin_lock protect.

0003:
- No changes.

0004:
- Commit comments rephrase act by Claudiu Manoil.

Changes from V3:
----------------
0001:

Fix and modify according to Vlid Buslov:
- Remove the struct gate_action and move the parameters to the
struct tcf_gate align with tc_action parameters. This would not need to
alloc rcu type memory with pointer.
- Remove the spin_lock type entry_lock which do not needed anymore, will
use the tcf_lock system provided.
- Provide lockep protect for the status parameters in the tcf_gate_act().
- Remove the cycletime 0 input warning, return error directly.

And:
- Remove Qci related description in the Kconfig for gate action.

0002:
- Fix rcu_read_lock protect range suggested by Vlid Buslov.

0003:
- No changes.

0004:
- Fix bug of gate maxoct wildcard condition not included.
- Fix the pass time basetime calculation report by Vladimir Otlean.

Changes from V2:
0001: No changes.
0002: No changes.
0003: No changes.
0004: Fix the vlan id filter parameter and add reject src mac
FF-FF-FF-FF-FF-FF filter in driver.

Changes from V1:
----------------
0000: Update description make it more clear
0001: Removed 'add update dropped stats' patch, will provide pull
request as standalone patches.
0001: Update commit description make it more clear ack by Jiri Pirko.
0002: No changes
0003: Fix some code style ack by Jiri Pirko.
0004: Fix enetc_psfp_enable/disable parameter type ack by test robot

iprout2 command patches:
  Not attach with these serial patches, will provide separate pull
request after kernel accept these patches.

Changes from RFC:
-----------------
0000: Reduce to 5 patches and remove the 4 max frame size offload and
flow metering in the policing offload action, Only keep gate action
offloading implementation.
0001: No changes.
0002:
 - fix kfree lead ack by Jakub Kicinski and Cong Wang
 - License fix from Jakub Kicinski and Stephen Hemminger
 - Update example in commit acked by Vinicius Costa Gomes
 - Fix the rcu protect in tcf_gate_act() acked by Vinicius

0003: No changes
0004: No changes
0005:
 Acked by Vinicius Costa Gomes
 - Use refcount kernel lib
 - Update stream gate check code position
 - Update reduce ref names more clear

iprout2 command patches:
0000: Update license expression and add gate id
0001: Add tc action gate man page

--------------------------------------------------------------------
These patches add stream gate action policing in IEEE802.1Qci (Per-Stream
Filtering and Policing) software support and hardware offload support in
tc flower, and implement the stream identify, stream filtering and
stream gate filtering action in the NXP ENETC ethernet driver.
Per-Stream Filtering and Policing (PSFP) specifies flow policing and
filtering for ingress flows, and has three main parts:
 1. The stream filter instance table consists of an ordered list of
stream filters that determine the filtering and policing actions that
are to be applied to frames received on a specific stream. The main
elements are stream gate id, flow metering id and maximum SDU size.
 2. The stream gate function setup a gate list to control ingress traffic
class open/close state. When the gate is running at open state, the flow
could pass but dropped when gate state is running to close. User setup a
bastime to tell gate when start running the entry list, then the hardware
would periodiclly. There is no compare qdisc action support.
 3. Flow metering is two rates two buckets and three-color marker to
policing the frames. Flow metering instance are as specified in the
algorithm in MEF10.3. The most likely qdisc action is policing action.

The first patch introduces an ingress frame flow control gate action,
for the point 2. The tc gate action maintains the open/close state gate
list, allowing flows to pass when the gate is open. Each gate action
may policing one or more qdisc filters. When the start time arrived, The
driver would repeat the gate list periodiclly. User can assign a passed
time, the driver would calculate a new future time by the cycletime of
the gate list.

The 0002 patch introduces the gate flow hardware offloading.

The 0003 patch adds support control the on/off for the tc flower
offloading by ethtool.

The 0004 patch implement the stream identify and stream filtering and
stream gate filtering action in the NXP ENETC ethernet driver. Tc filter
command provide filtering keys with MAC address and VLAN id. These keys
would be set to stream identify instance entry. Stream gate instance
entry would refer the gate action parameters. Stream filter instance
entry would refer the stream gate index and assign a stream handle value
matches to the stream identify instance.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to add tc flower offload for the enetc IEEE 802.1Qci(PSFP)
function. There are four main feature parts to implement the flow
policing and filtering for ingress flow with IEEE 802.1Qci features.
They are stream identify(this is defined in the P802.1cb exactly but
needed for 802.1Qci), stream filtering, stream gate and flow metering.
Each function block includes many entries by index to assign parameters.
So for one frame would be filtered by stream identify first, then
flow into stream filter block by the same handle between stream identify
and stream filtering. Then flow into stream gate control which assigned
by the stream filtering entry. And then policing by the gate and limited
by the max sdu in the filter block(optional). At last, policing by the
flow metering block, index choosing at the fitering block.
So you can see that each entry of block may link to many upper entries
since they can be assigned same index means more streams want to share
the same feature in the stream filtering or stream gate or flow
metering.
To implement such features, each stream filtered by source/destination
mac address, some stream maybe also plus the vlan id value would be
treated as one flow chain. This would be identified by the chain_index
which already in the tc filter concept. Driver would maintain this chain
and also with gate modules. The stream filter entry create by the gate
index and flow meter(optional) entry id and also one priority value.
Offloading only transfer the gate action and flow filtering parameters.
Driver would create (or search same gate id and flow meter id and
 priority) one stream filter entry to set to the hardware. So stream
filtering do not need transfer by the action offloading.
This architecture is same with tc filter and actions relationship. tc
filter maintain the list for each flow feature by keys. And actions
maintain by the action list.

Below showing a example commands by tc:
> tc qdisc add dev eth0 ingress
> ip link set eth0 address 10:00:80:00:00:00
> tc filter add dev eth0 parent ffff: protocol ip chain 11 \
	flower skip_sw dst_mac 10:00:80:00:00:00 \
	action gate index 10 \
	sched-entry open 200000000 1 8000000 \
	sched-entry close 100000000 -1 -1

Command means to set the dst_mac 10:00:80:00:00:00 to index 11 of stream
identify module. Then setting the gate index 10 of stream gate module.
Keep the gate open for 200ms and limit the traffic volume to 8MB in this
sched-entry. Then direct the frames to the ingress queue 1.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to let ethtool enable/disable the tc flower offload
features. Hardware ENETC has the feature of PSFP which is for per-stream
policing. When enable the tc hw offloading feature, driver would enable
the IEEE 802.1Qci feature. It is only set the register enable bit for
this feature not enable for any entry of per stream filtering and stream
gate or stream identify but get how much capabilities for each feature.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the gate action to the flow action entry. Add the gate parameters to
the tc_setup_flow_action() queueing to the entries of flow_action_entry
array provide to the driver.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce a ingress frame gate control flow action.
Tc gate action does the work like this:
Assume there is a gate allow specified ingress frames can be passed at
specific time slot, and be dropped at specific time slot. Tc filter
chooses the ingress frames, and tc gate action would specify what slot
does these frames can be passed to device and what time slot would be
dropped.
Tc gate action would provide an entry list to tell how much time gate
keep open and how much time gate keep state close. Gate action also
assign a start time to tell when the entry list start. Then driver would
repeat the gate entry list cyclically.
For the software simulation, gate action requires the user assign a time
clock type.

Below is the setting example in user space. Tc filter a stream source ip
address is 192.168.0.20 and gate action own two time slots. One is last
200ms gate open let frame pass another is last 100ms gate close let
frames dropped. When the ingress frames have reach total frames over
8000000 bytes, the excessive frames will be dropped in that 200000000ns
time slot.

> tc qdisc add dev eth0 ingress

> tc filter add dev eth0 parent ffff: protocol ip \
	   flower src_ip 192.168.0.20 \
	   action gate index 2 clockid CLOCK_TAI \
	   sched-entry open 200000000 -1 8000000 \
	   sched-entry close 100000000 -1 -1

> tc chain del dev eth0 ingress chain 0

"sched-entry" follow the name taprio style. Gate state is
"open"/"close". Follow with period nanosecond. Then next item is internal
priority value means which ingress queue should put. "-1" means
wildcard. The last value optional specifies the maximum number of
MSDU octets that are permitted to pass the gate during the specified
time interval.
Base-time is not set will be 0 as default, as result start time would
be ((N + 1) * cycletime) which is the minimal of future time.

Below example shows filtering a stream with destination mac address is
10:00:80:00:00:00 and ip type is ICMP, follow the action gate. The gate
action would run with one close time slot which means always keep close.
The time cycle is total 200000000ns. The base-time would calculate by:

 1357000000000 + (N + 1) * cycletime

When the total value is the future time, it will be the start time.
The cycletime here would be 200000000ns for this case.

> tc filter add dev eth0 parent ffff:  protocol ip \
	   flower skip_hw ip_proto icmp dst_mac 10:00:80:00:00:00 \
	   action gate index 12 base-time 1357000000000 \
	   sched-entry close 200000000 -1 -1 \
	   clockid CLOCK_TAI
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The side band interrupt service routine is not available on chips
like 7211, or rather, it does not permit the signaling of wake-up
events due to the complex interrupt hierarchy.

Move the wake-up event accounting into a .resume_noirq function,
account for possible wake-up events and clear the MPD/HFB interrupts
from there, while leaving the hardware untouched until the resume
function proceeds with doing its usual business.

Because bcmgenet_wol_power_down_cfg() now enables the MPD and HFB
interrupts, it is invoked by a .suspend_noirq function to prevent
the servicing of interrupts after the clocks have been disabled.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alex Elder says:

====================
net: ipa: don't cache channel state

This series removes a field that holds a copy of a channel's state
at the time it was last fetched.  In principle the state can change
at any time, so it's better to just fetch it whenever needed.  The
first patch is just preparatory, simplifying the arguments to
gsi_channel_state().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

It is possible for a GSI channel's state to be changed as a result
of an action by a different execution environment.  Specifically,
the modem is able to issue a GSI generic command that causes a state
change on a GSI channel associated with the AP.

A channel's state only needs to be known when a channel is allocated
or deallocaed, started or stopped, or reset.  So there is little
value in caching the state anyway.

Stop recording a copy of the channel's last known state, and instead
fetch the true state from hardware whenever it's needed.  In such
cases, *do* record the state in a local variable, in case an error
message reports it (so the value reported is the value seen).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pass a channel pointer rather than a GSI pointer and channel ID to
gsi_channel_state().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Russell King says:

====================
net: dsa: mv88e6xxx: augment phylink support for 10G

This series adds phylink 10G support for the 88E6390 series switches,
as suggested by Andrew Lunn.

The first patch cleans up the code to use generic definitions for the
registers in a similar way to what was done with the initial conversion
of 1G serdes support.

The second patch adds the necessary bits 10GBASE mode to the
pcs_get_state() method.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for reading and reporting the 10G link status on the
88e6390 in addition to the 1000BASE-X/2500BASE-X/SGMII status.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

The private MV88E6390_PCS_CONTROL_1 definitions in serdes.h reflects
the IEEE 802.3 standard PCS control register 1 definitions, only
offset by 0x1000 in the PHYXS register space.  Rather than inventing
our own, use those that already exist, and name the register
MV88E6390_10G_CTRL1.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Igor Russkikh says:

====================
net: atlantic: A2 support

This patchset adds support for the new generation of Atlantic NICs.

Chip generations are mostly compatible register-wise, but there are still
some differences. Therefore we've made some of first generation (A1) code
non-static to re-use it where possible.

Some pieces are A2 specific, in which case we redefine/extend such APIs.

v2:
 * removed #pragma pack (2 structures require the packed attribute);
 * use defines instead of magic numbers where possible;

v1: https://patchwork.ozlabs.org/cover/1276220/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Chip generations are mostly compatible register-wise, but there are still
some differences. Therefore we've made some of first generation (A1) code
non-static to re-use it where possible.

Some pieces are A2 specific, in which case we redefine/extend such APIs.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds basic A2 HW initialization / deinitialization.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Co-developed-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds common functions (mostly FW-related), which are
needed for basic A2 HW initialization / deinitialization.
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Co-developed-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds A2 register definitions for basic A2 HW
initialization / deinitialization.
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Co-developed-by: Egor Pomozov <epomozov@marvell.com>
Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Co-developed-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Co-developed-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds RPF-related hw_ops, which are needed for basic
functionality.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Co-developed-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RPF is one of the modules which has been significantly
changed/extended on A2.

This patch adds the necessary A2 register definitions
for RPF, which are used in follow-up patches.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Co-developed-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds basic hw_ops layout for A2.

Actual implementation will be added in the follow-up patches.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the minimum set of FW ops for A2.
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Co-developed-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the bare minimum of A2 HW bindings required to
get fw_ops working.
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the driver<->firmware interface for A2
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IS_CHIP feature will be used to differentiate between A1 and A2,
where necessary. Thus, move it to aq_hw.h, rename it and make
it accept the 'hw' pointer.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes potential crash in case if hw_get_regs is NULL.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

hw_get_fw_version() never fails, so this patch simplifies its
usage by utilizing return value instead of output argument.
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A2 will have a different implementation of these 2 APIs, so
this patch moves them to hw_ops in preparation for A2.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Co-developed-by: Dmitry Bezrukov <dbezrukov@marvell.com>
Signed-off-by: Dmitry Bezrukov <dbezrukov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds defines for 10M and EEE 100M link modes, which are
supported by A2.

10M support is added in this patch series.
EEE is out of scope, but will be added in a follow-up series.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adding device ids for the new generation of atlantic nic.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Aquantia is now part of Marvell. Thus, update the driver description.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
since devm_ioremap() does not check input parameters for null.

This is detected by Coccinelle semantic patch.

@@
expression pdev, res, n, t, e, e1, e2;
@@

res = \(platform_get_resource\|platform_get_resource_byname\)(pdev, t, n);
+ if (!res)
+   return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);

Fixes: 03f66f06 ("net: ethernet: ti: davinci_mdio: use devm_ioremap()")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In skb_panic() the real pointer values are really needed to diagnose
issues, e.g. data and head are related (to calculate headroom). The
hashed versions of the addresses doesn't make much sense here. The
patch use the printk specifier %px to print the actual address.

The printk documentation on %px:
https://www.kernel.org/doc/html/latest/core-api/printk-formats.html#unmodified-addresses

Fixes: ad67b74d ("printk: hash addresses printed with %p")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

No new feature, just to simplify stm32 part to be easier to use.
Add by default all Ethernet clocks in DT, and activate or not in function
of phy mode, clock frequency, if property "st,ext-phyclk" is set or not.
Keep backward compatibility
--------------------------------------------------------------------------
|PHY_MODE |    Normal | PHY wo crystal|   PHY wo crystal   |  No 125Mhz  |
|         |	      |      25MHz    |        50MHz       |  from PHY   |
--------------------------------------------------------------------------
|  MII    |	 -    |     eth-ck    |       n/a          |	    n/a  |
|         |	      | st,ext-phyclk |                    |             |
--------------------------------------------------------------------------
|  GMII   |	 -    |     eth-ck    |       n/a          |	    n/a  |
|         |	      | st,ext-phyclk |                    |             |
--------------------------------------------------------------------------
| RGMII   |	 -    |     eth-ck    |       n/a          |     eth-ck  |
|         |	     | st,ext-phyclk |                    |st,eth-clk-sel|
|         |	     |               |                    |       or     |
|         |	     |               |                    | st,ext-phyclk|
----------------==--------------------------------------------------------
| RMII    |	 -   |     eth-ck    |      eth-ck        |       n/a    |
|         | 	     | st,ext-phyclk | st,eth-ref-clk-sel |              |
|         | 	     |               | or st,ext-phyclk   |              |
--------------------------------------------------------------------------
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch changes the behavior of TCP_LINGER2 about its limit. The
sysctl_tcp_fin_timeout used to be the limit of TCP_LINGER2 but now it's
only the default value. A new macro named TCP_FIN_TIMEOUT_MAX is added
as the limit of TCP_LINGER2, which is 2 minutes.

Since TCP_LINGER2 used sysctl_tcp_fin_timeout as the default value
and the limit in the past, the system administrator cannot set the
default value for most of sockets and let some sockets have a greater
timeout. It might be a mistake that let the sysctl to be the limit of
the TCP_LINGER2. Maybe we can add a new sysctl to set the max of
TCP_LINGER2, but FIN-WAIT-2 timeout is usually no need to be too long
and 2 minutes are legal considering TCP specs.

Changes in v3:
- Remove the new socket option and change the TCP_LINGER2 behavior so
  that the timeout can be set to value between sysctl_tcp_fin_timeout
  and 2 minutes.

Changes in v2:
- Add int overflow check for the new socket option.

Changes in v1:
- Add a new socket option to set timeout greater than
  sysctl_tcp_fin_timeout.
Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
r8169: improve user message handling

Series improves few aspects of handling messages to users.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Considering the few messages we have in the driver, there's not really
a benefit in being able to control them on a message type level.
Therefore simplify the code and switch to the netdev_xxx message
functions. In addition add net_ratelimit() to messages that can be
printed from a hot path.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When preparing an unrelated change, checkpatch complained about this
redundant out-of-memory message. Therefore remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The counter handling functions can only fail if rtl8169_do_counters()
times out. In the poll function we emit an error message in case of
timeout, therefore we don't have to propagate the timeout all the
way up just to print another message basically saying the same.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Net core -  __dev_set_promiscuity - prints a message already when
promiscuous mode in entered/left, therefore we don't have to do this
in the driver too. Also the driver message would be misleading
(would be because "link" message level is disabled per default)
because it would print "promisc mode enabled" even if it's being
left. Reason is that __dev_change_flags() calls dev_set_rx_mode()
before touching the promisc flag.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>