- 02 Dec, 2013 9 commits
-
-
Simon Wunderlich authored
The csa finalize worker needs to change the beacon information (for different modes). These are normally protected under rtnl lock, but the csa finalize worker is called by drivers and should not acquire the RTNL lock. Therefore change access protection for beacons to sdata/wdev lock. Reported-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
Simon Wunderlich <sw@simonwunderlich.de> [fix sdata_dereference] Signed-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Simon Wunderlich authored
To avoid race conditions in functions which modify the beacon information, lock these using the wdev lock. This is especially required to avoid problems for csa handling functions which modify beacons but can not be called under rtnl lock. Reported-by:
-
Bob Copeland authored
The local TSF timer is used to compute the timing offset between mesh peers on beacon reception. However, asking the device for the TSF is not very accurate, so we prefer to use rx->mactime if available. In the latter case, calling drv_get_tsf() just adds more delay into the RX path, so skip it if we can. Signed-off-by:
Bob Copeland <bob@cozybit.com> Signed-off-by:
-
Andrei Otcheretianski authored
Change cfg80211 and mac80211 to use cfg80211_mgmt_tx_params struct to aggregate parameters for mgmt_tx functions. This makes the functions' signatures less clumsy and allows less painful parameters extension. Signed-off-by:
Andrei Otcheretianski <andrei.otcheretianski@intel.com> [fix all other drivers] Signed-off-by:
-
Avri Altman authored
There's a bug in tracking HT opmode changes in mac80211, it fails to update the driver when the channel parameters don't change. Move the code to do the HT opmode checking independently of the channel/bandwidth tracking. Signed-off-by:
Avri Altman <avri.altman@intel.com> [edit commit message] Signed-off-by:
-
Johannes Berg authored
All interface types now properly clean up their stations using some form of sta_info_flush() themselves, so there's no need to try it again at teardown. Remove the call to get rid of the extra delay from the synchronize_net() and rcu_barrier() calls. Reported-by:
Moshe Benji <moshe.benji@intel.com> Signed-off-by:
-
Matti Gottlieb authored
Measure TX latency and jitter statistics per station per TID. These Measurements are disabled by default and can be enabled via debugfs. Features included for each station's TID: 1. Keep count of the maximum and average latency of Tx frames. 2. Keep track of many frames arrived in a specific time range (need to enable through debugfs and configure the bins ranges) Signed-off-by:
Matti Gottlieb <matti.gottlieb@intel.com> Signed-off-by:
-
Johannes Berg authored
The beacon timers really shouldn't use any clock that is subject to adjustments from userspace, particularly not CLOCK_REALTIME. Use CLOCK_MONOTONIC_RAW instead. Signed-off-by: -
Felix Fietkau authored
nla_put_flag needs a real nl80211 attribute id, not a wiphy flag bit. While at it, split 5 and 10 MHz capability flags in case we ever need to support hardware that can only do one of the two. Also move the flag settings to the split-only information so we don't increase the space needed for old userspace. Signed-off-by:
Felix Fietkau <nbd@openwrt.org> [change location of flag setting] Signed-off-by:
-
- 25 Nov, 2013 31 commits
-
-
Karl Beldan authored
ATM minstrel_ht does not check whether a sampling rate is supported. Unsupported rates attempts can trigger when there are holes in bitfields of supported MCSes belonging to the same group (e.g many devices are MCS32 capable without MCS33->39 capable, also we systematically have a hole for CCK rates). Drop any attempts to sample unsupported rates, as suggested by Felix. This is not a problem in minstrel which fills a per STA sample table with only supported rates (though only at init). Signed-off-by:
Karl Beldan <karl.beldan@rivierawaves.com> Signed-off-by:
-
Luis R. Rodriguez authored
This lets us later reuse the more generic reg_dfs_region_str(). Signed-off-by:
Luis R. Rodriguez <mcgrof@do-not-panic.com> Signed-off-by:
-
Luis R. Rodriguez authored
Signed-off-by:
-
Luis R. Rodriguez authored
Only allow DFS to be set if the DFS regions agree. Signed-off-by:
-
Luis R. Rodriguez authored
u8 was used in some other places, just stick to the enum, this forces us to express the values that are expected. Signed-off-by:
-
Karl Beldan authored
ATM, only the first array value returned by get_random_bytes is used. This change moves the call to get_random_bytes from the nested loop it is in to its parent. While at it, replace get_random_bytes with prandom_bytes since PRNs are way enough for the selection process. After this, minstrel_ht reclaims 80 PR-bytes instead of 640 R-bytes. minstrels use sample tables to probe different rates in a randomized manner. minstrel_ht inits one single sample table upon registration (during subsys_initcalls) and minstrel uses one per STA addition in minstrel. Signed-off-by:
-
Karl Beldan authored
Consecutive MCSes in [8*(NSS-1)->8*NSS[ have the same number NSS of streams (except for MCS32 which is mishandled ATM). ATM minstrel_ht uses MCS_GROUP_RATES in place of this 8 modulus. This change replaces such occurences and by doing so allows for different values of MCS_GROUP_RATES (e.g to cope with VHT MCS8,9). Signed-off-by:
-
Eliad Peller authored
Add a new field to ieee80211_chanctx_conf to indicate the min required channel configuration. Tuning to a narrower channel might help reducing the noise level and saving some power. The min required channel definition is the max of all min required channel definitions of the interfaces bound to this channel context. In AP mode, use 20MHz when there are no connected station. When a new station is added/removed, calculate the new max bandwidth supported by any of the stations (e.g. 80MHz when 80MHz and 40MHz stations are connected). In other cases, simply use bss_conf.chandef as the min required chandef. Notify drivers about changes to this field by calling drv_change_chanctx with a new CHANGE_MIN_WIDTH notification. Signed-off-by:
Eliad Peller <eliad@wizery.com> Reviewed-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Eyal Shapira authored
Introduce shift and mask defines for beamformee STS cap and number of sounding dimensions cap as these can take any 3 bit value. While at it also cleanup an unrequired parenthesis. Signed-off-by:
Eyal Shapira <eyal@wizery.com> Reviewed-by:
-
Luciano Coelho authored
There is no reason why we should have only one channel switch announcement at a time for a single phy. When support for channel switch with multiple contexts and multiple vifs per context is implemented, we will need the chandef data for each vif. Move the csa_chandef structure to sdata to prepare for this. Reviewed-by:
Luciano Coelho <luciano.coelho@intel.com> [Fixed compilation with mesh] Signed-off-by:
-
Chun-Yeow Yeoh authored
Use put_unaligned_le16 and put_unaligned_le32 for mesh_path_error_tx and mesh_path_sel_frame_tx. Signed-off-by:
Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by:
-
Chun-Yeow Yeoh authored
Use put_unaligned_le16 in mesh_plink_frame_tx. Signed-off-by:
-
Luis R. Rodriguez authored
Certain vendors may want to disable the processing of country IEs so that they can continue using the regulatory domain the driver or user has set. Currently there is no way to stop the core from processing country IEs, so add support to the core to ignore country IE hints. Cc: Mihir Shete <smihir@qti.qualcomm.com> Cc: Henri Bahini <hbahini@qca.qualcomm.com> Cc: Tushnim Bhattacharyya <tushnimb@qca.qualcomm.com> Signed-off-by:
-
Luis R. Rodriguez authored
802.11 cards may have different country IE parsing behavioural preferences and vendors may want to support these. These preferences were managed by the REGULATORY_CUSTOM_REG and the REGULATORY_STRICT_REG flags and their combination. Instead of using this existing notation, split out the country IE behavioural preferences as a new flag. This will allow us to add more customizations easily and make the code more maintainable. Cc: Mihir Shete <smihir@qti.qualcomm.com> Cc: Henri Bahini <hbahini@qca.qualcomm.com> Cc: Tushnim Bhattacharyya <tushnimb@qca.qualcomm.com> Signed-off-by:
-
Luis R. Rodriguez authored
We'll expand this later, this will make it easier to classify and review what things are related to regulatory or not. Coccinelle only missed 4 hits, which I had to do manually, supplying the SmPL in case of merge conflicts. @@ struct wiphy *wiphy; @@ -wiphy->flags |= WIPHY_FLAG_CUSTOM_REGULATORY +wiphy->regulatory_flags |= REGULATORY_CUSTOM_REG @@ expression e; @@ -e->flags |= WIPHY_FLAG_CUSTOM_REGULATORY +e->regulatory_flags |= REGULATORY_CUSTOM_REG @@ struct wiphy *wiphy; @@ -wiphy->flags &= ~WIPHY_FLAG_CUSTOM_REGULATORY +wiphy->regulatory_flags &= ~REGULATORY_CUSTOM_REG @@ struct wiphy *wiphy; @@ -wiphy->flags & WIPHY_FLAG_CUSTOM_REGULATORY +wiphy->regulatory_flags & REGULATORY_CUSTOM_REG @@ struct wiphy *wiphy; @@ -wiphy->flags |= WIPHY_FLAG_STRICT_REGULATORY +wiphy->regulatory_flags |= REGULATORY_STRICT_REG @@ expression e; @@ -e->flags |= WIPHY_FLAG_STRICT_REGULATORY +e->regulatory_flags |= REGULATORY_STRICT_REG @@ struct wiphy *wiphy; @@ -wiphy->flags &= ~WIPHY_FLAG_STRICT_REGULATORY +wiphy->regulatory_flags &= ~REGULATORY_STRICT_REG @@ struct wiphy *wiphy; @@ -wiphy->flags & WIPHY_FLAG_STRICT_REGULATORY +wiphy->regulatory_flags & REGULATORY_STRICT_REG @@ struct wiphy *wiphy; @@ -wiphy->flags |= WIPHY_FLAG_DISABLE_BEACON_HINTS +wiphy->regulatory_flags |= REGULATORY_DISABLE_BEACON_HINTS @@ expression e; @@ -e->flags |= WIPHY_FLAG_DISABLE_BEACON_HINTS +e->regulatory_flags |= REGULATORY_DISABLE_BEACON_HINTS @@ struct wiphy *wiphy; @@ -wiphy->flags &= ~WIPHY_FLAG_DISABLE_BEACON_HINTS +wiphy->regulatory_flags &= ~REGULATORY_DISABLE_BEACON_HINTS @@ struct wiphy *wiphy; @@ -wiphy->flags & WIPHY_FLAG_DISABLE_BEACON_HINTS +wiphy->regulatory_flags & REGULATORY_DISABLE_BEACON_HINTS Generated-by: Coccinelle SmPL Cc: Julia Lawall <julia.lawall@lip6.fr> Cc: Peter Senna Tschudin <peter.senna@gmail.com> Cc: Mihir Shete <smihir@qti.qualcomm.com> Cc: Henri Bahini <hbahini@qca.qualcomm.com> Cc: Tushnim Bhattacharyya <tushnimb@qca.qualcomm.com> Signed-off-by:
-
Chun-Yeow Yeoh authored
use put_unaligned_le16 for precedence value in mesh channel switch support Signed-off-by:
-
Karl Beldan authored
Signed-off-by:
-
Luis R. Rodriguez authored
This reflects that case is now completely separated. Signed-off-by:
-
Luis R. Rodriguez authored
This splits up the driver regulatory update on its own, this helps simplify the reading the case. Signed-off-by:
-
Luis R. Rodriguez authored
This splits out the user regulatory update on its own, this helps simplify reading the case. Signed-off-by:
-
Luis R. Rodriguez authored
This splits up the core regulatory update to be set on its own helper. This should make it easier to read exactly what type of requests should be expected there. In this case its clear that NL80211_REGDOM_SET_BY_CORE is only used by the core for updating the world regulatory domain. This is consistant with the nl80211.h documentation. Signed-off-by:
-
Luis R. Rodriguez authored
last_request is RCU protected, since we're getting it on set_regdom() we might as well pass it to ensure the same request is being processed, otherwise there is a small race it could have changed. This makes processing of the request atomic. Signed-off-by:
-
Luis R. Rodriguez authored
Drivers that set the WIPHY_FLAG_CUSTOM_REGULATORY skip the core world regulatory domain updates, but do want their reg_notifier() called. Move the check for this closer to the source of the check that detected skipped was required and while at it add a helper for the notifier calling. This has no functional changes. This brings together the place where we call the reg_notifier() will be called. Signed-off-by:
-
Luis R. Rodriguez authored
It seems some out of tree drivers were using a regulatory_hint("00") to trigger off the wiphy regulatory notifier, for those cases just setting the WIPHY_FLAG_CUSTOM_REGULATORY would suffice to call the reg_notifier() for a world regulatory domain update. If drivers find other needs for calling the reg_notifier() a proper implemenation is preferred. Signed-off-by: -
Luis R. Rodriguez authored
All the regulatory request process routines use the same pattern. Signed-off-by:
-
Luis R. Rodriguez authored
This enforces proper RCU APIs accross the code. Signed-off-by:
-
Luis R. Rodriguez authored
This is common code, this reduces the chance of making a mistake of how we free it. Signed-off-by:
-
Luis R. Rodriguez authored
By dealing with non country IE conficts first we can shift the code that deals with the conflict to the left. This has no functional changes. Signed-off-by:
-
Luis R. Rodriguez authored
This is the last split up of the old unified __regultory_hint() processing set of functionality, it moves the country IE processing all on its own. This makes it easier to follow and read what exactly is going on for the case of processing country IEs. Signed-off-by:
-
Luis R. Rodriguez authored
This makes the code easier to read and follow. Signed-off-by:
-
Luis R. Rodriguez authored
This makes the code path easier to read and lets us split out some functionality that is only user specific, that makes it easier to read the other types of requests. Signed-off-by:
-
