- 16 Feb, 2009 40 commits
-
-
Alexander Duyck authored
Currently the driver uses advanced descriptors for its main functionality, but then uses legacy when testing. This patch changes this so that advanced descriptors are used throughout and all mentions of legacy descriptors are removed. Signed-off-by:
Alexander Duyck <alexander.h.duyck@intel.com> Acked-by:
Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Alexander Duyck authored
This patch removes all of the unused defines from the .h files contained in igb. For some defines there was a use and so I plugged them into the correct locations. Signed-off-by:
-
Alexander Duyck authored
This patch combines a pair of if statements into one. Signed-off-by:
-
Alexander Duyck authored
IP Checksum enable doesn't need packet split in order to function. It only requires the use of advanced descriptors which the current igb driver does. So we can enable it always without any issues. Signed-off-by:
-
Alexander Duyck authored
Update the Adaptive Interrupt Moderation algorithm so that the low latency state is triggered less easily to prevent high interrupt loads. Signed-off-by:
-
Alexander Duyck authored
This patch is intended to hold several whitespace, formatting, and comment cleanups that have been found while cleaning up the igb driver. Signed-off-by:
-
Lennert Buytenhek authored
Controlled by a compile-time (Kconfig) option for now, since it isn't a win in all cases. Signed-off-by:
Lennert Buytenhek <buytenh@marvell.com> Signed-off-by:
-
Lennert Buytenhek authored
Signed-off-by:
-
Lennert Buytenhek authored
Signed-off-by:
-
Lennert Buytenhek authored
Rename the mp->default_[rt]x_ring_size variables to ->[rt]x_ring_size, allow them to be read via the standard ethtool ->get_ringparam() op, and add a ->set_ringparam() op to allow resizing them at run time. Signed-off-by:
-
Lennert Buytenhek authored
This patch: - increases the precision of the receive/transmit interrupt coalescing register value computations by using 64bit temporaries; - adds functions to read the current hardware coalescing register values and convert them back to usecs; - exports the {get,set} {rx,tx} coal methods via the standard ethtool coalescing interface. Signed-off-by: -
Lennert Buytenhek authored
It's a waste having two different versions of this structure around when the differences between ethtool ops for phy'd and phy-less interfaces are so minor. Signed-off-by:
-
Hannes Eder authored
Jiffies are unsigned long, make sure we fit in jiffies store variable on archs with bits per long > 32. Patch suggested by Jiri Slaby. Signed-off-by:
Hannes Eder <hannes@hanneseder.net> Signed-off-by:
-
Hannes Eder authored
Fix this sparse warnings: drivers/isdn/mISDN/clock.c:44:1: warning: symbol 'iclock_lock' was not declared. Should it be static? drivers/isdn/mISDN/clock.c:45:9: warning: symbol 'iclock_count' was not declared. Should it be static? drivers/isdn/mISDN/clock.c:46:17: warning: symbol 'iclock_tv' was not declared. Should it be static? drivers/isdn/mISDN/clock.c:47:9: warning: symbol 'iclock_tv_valid' was not declared. Should it be static? drivers/isdn/mISDN/clock.c:48:20: warning: symbol 'iclock_current' was not declared. Should it be static? Signed-off-by:
-
Hannes Eder authored
Fix this sparse warnings: drivers/isdn/hardware/mISDN/hfcpci.c:59:19: warning: symbol 'hfc_tl' was not declared. Should it be static? drivers/isdn/hardware/mISDN/hfcpci.c:60:9: warning: symbol 'hfc_jiffies' was not declared. Should it be static? drivers/isdn/hardware/mISDN/hfcsusb.h:201:6: warning: symbol 'conf_str' was not declared. Should it be static? drivers/isdn/hardware/mISDN/hfcsusb.h:319:12: warning: symbol 'HFC_TE_LAYER1_STATES' was not declared. Should it be static? drivers/isdn/hardware/mISDN/hfcsusb.h:331:12: warning: symbol 'HFC_NT_LAYER1_STATES' was not declared. Should it be static? drivers/isdn/hardware/mISDN/hfcsusb.c:38:12: warning: symbol 'hfcsusb_rev' was not declared. Should it be static? drivers/isdn/hardware/mISDN/hfcsusb.c:978:1: warning: symbol 'fill_isoc_urb' was not declared. Should it be static? drivers/isdn/hardware/mISDN/hfcsusb.c:1724:1: warning: symbol 'setup_hfcsusb' was not declared. Should it be static? Signed-off-by:
-
Eilon Greenstein authored
And updating the year Signed-off-by:
Eilon Greenstein <eilong@broadcom.com> Signed-off-by:
-
Eilon Greenstein authored
Whitespaces, empty lines, 80 columns, indentations and removing redundant parenthesis Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
-
Eilon Greenstein authored
Re-arrange the driver debug print to support the Tx multi-queue and add support for debug prints at the end of the ring (when start<end) Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by:
-
Eilon Greenstein authored
Resolving the majority of the issues, but there are still some left for future patches. Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
-
Eilon Greenstein authored
This is the device info from the chip shared memory - rename to avoid confusion Signed-off-by:
-
Eilon Greenstein authored
When loading in diag mode, set the device to loopback instead of normal link and then changing it to loopback mode Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
-
Eilon Greenstein authored
The driver default WoL setting is set to the nvram default value Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
-
Eilon Greenstein authored
When enabling many debug prints, it can take a while before processing an event. To ease the debug process, allow bigger timeout before giving up Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
-
Eilon Greenstein authored
Allows better debug capabilities if the user wants to force an MRRS value Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
-
Eilon Greenstein authored
Supporting non-default pre-emphasis settings for the internal and some external PHYs Signed-off-by:
Yaniv Rosner <yanivr@broadcom.com> Signed-off-by:
-
Eilon Greenstein authored
Fixing the function name Signed-off-by:
-
Eilon Greenstein authored
This code is disabled, so removing it to avoid confusion Signed-off-by:
-
Eilon Greenstein authored
This 1G interface (on top of the 4 lanes 10G interface) requires additional setting to work in CL45 Signed-off-by:
-
Eilon Greenstein authored
The NIG_ENABLE does not reset the emac. Replace it with explicit reset Signed-off-by:
-
Eilon Greenstein authored
Some PHYs (like the BCM8726) FW version cannot be read after activating the PHY, so we need to save this information Signed-off-by:
-
