Steps to reproduce the problem:
	1) Enable RTC wake-up option in BIOS Setup
	2) Issue one of these commands in the OS: "poweroff"
	   or "shutdown -h now"
	3) System will shut down and then reboot automatically

Root-cause of the issue:
	1) During the shutdown process, the hwclock utility is used
	   to save the system clock to hardware clock (RTC).
	2) The hwclock utility invokes ioctl() with RTC_UIE_ON. The
	   kernel configures the RTC alarm for the periodic interrupt
	   (every 1 second).
	3) The hwclock uitlity closes the /dev/rtc0 device, and the
	   kernel disables the RTC alarm irq (AIE bit of Register B)
	   via ioctl() with RTC_UIE_OFF. But, the configured alarm
	   time is the current_time + 1.
	4) After the next 1 second is elapsed, the AF (alarm
	   interrupt flag) of Register C is set.
	5) The S5 handler in BIOS is invoked to configure alarm
	   registers (enable AIE bit and configure alarm date/time).
	   But, BIOS does not clear the previous interrupt status
	   during alarm configuration. Therefore, "AF=AIE=1" causes
	   the rtc device to trigger an interrupt.
	6) So, the machine reboots automatically right after shutdown.

This patch cancels the alarm timer if the following condictions are
met (suggested by Alexandre):
	1) The configured alarm time is equal to current_time + 1
	   seconds.
	2) The AIE timer is not in use.

The member 'alarm_expires' is introduced in struct cmos_rtc because
of the following reasons:
	1) The configured alarm time can be retrieved from
	   cmos_read_alarm(), but we need to take the 'wrapped
	   timestamp' and 'time rollover' into consideration. The
	   function __rtc_read_alarm() eliminates the concerns. To
	   avoid the duplicated code in the lower level RTC driver,
	   invoking __rtc_read_alarm from the lower level RTC driver
	   is not encouraged. Moreover, the compilation error 'the
	   undefined __rtc_read_alarm" is observed if the lower level
	   RTC driver is compiled as a kernel module.
	2) The uie_rtctimer.node.expires and aie_timer.node.expires can
	   be retrieved for the configured alarm time. But, the problem
	   is that either of them might configure the CMOS alarm time.
	   We cannot make sure UIE timer or AIE tiemr configured the
	   CMOS alarm time before. (uie_rtctimer or aie_timer is enabled
	   and then is disabled).
	3) The patch introduces the member 'alarm_expires' to keep the
	   newly configured alarm time, so the above-mentioned concerns
	   can be eliminated.

The issue goes away after 20-time shutdown tests.
Signed-off-by: Adrian Huang <ahuang12@lenovo.com>
Tested-by: Egbert Eich <eich@suse.de>
Tested-by: Diego Ercolani <diego.ercolani@gmail.com>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Add DA9062 RTC support into the existing DA9063 RTC driver component by
using generic access tables for common register and bit mask definitions.

The following change will add generic register and bit mask support to the
DA9063 RTC. The changes are slightly complicated by requiring support for
three register sets: DA9063-AD, DA9063-BB and DA9062-AA.

The following alterations have been made to the DA9063 RTC:

- Addition of a da9063_compatible_rtc_regmap structure to hold all generic
  registers and bitmasks for this type of RTC component.
- A re-write of struct da9063 to use pointers for regmap and compatible
  registers/masks definitions
- Addition of a of_device_id table for DA9063 and DA9062 defaults
- Refactoring functions to use struct da9063_compatible_rtc accesses to
  generic registers/masks instead of using defines from registers.h
- Re-work of da9063_rtc_probe() to use of_match_node() and dev_get_regmap()
  to provide initialisation of generic registers and masks and access to
  regmap
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Implement the suspend/resume function in order to control rtc's irq_wake flag and handle as wakeup source.
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Acked-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Instead of creating wakealarm attribute manually, after the device has been
registered, let's rely on facilities provided by the attribute groups to
control which attributes are visible and which are not. This allows to
create all needed attributes at once, at the same time that we register RTC
class device.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Instead of using older style DEVICE_ATTR for wakealarm attribute let's
switch to using DEVICE_ATTR_RW that ensures consistent across the kernel
permissions on the attribute.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Users of rtc_does_wakealarm() return value treat it as boolean so let's
change the signature accordingly.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Since commit e6229bec ("rtc: make rtc_update_irq callable with irqs
enabled") rtc_update_irq() is callable with irqs enabled.
Signed-off-by: Henri Roosen <henriroosen@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Since dab472eb ("i2c / ACPI: Use 0 to indicate that device does not
have interrupt assigned"), 0 is not a valid i2c client irq anymore, so
change all driver's checks accordingly.

The same issue occurs when the device is instantiated via device tree
with no IRQ, or from the i2c sysfs interface, even before the patch
above.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

struct rtc embeds both struct dev and struct cdev.  Unfortunately character
device structure may outlive the parent rtc structure unless we set it up
as parent of character device so that it will stay pinned until character
device is freed.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Technically the address of rtc->dev can never be NULL, so get_device()
can never fail. Also caller of rtc_device_unregister() supposed to be
the owner of the device and thus have a valid reference. Therefore
call to get_device() is not needed here.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Commit 59cca865 ("drivers/rtc/class.c: fix device_register() error
handling") correctly noted that naked kfree() should not be used after
failed device_register() call, however, while it added the needed
put_device() it forgot to remove the original kfree() causing double-free.

Cc: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The current codes use CSR platform specific API exported by machine
codes to read/write RTC registers. they are:
sirfsoc_rtc_iobrg_readl()
sirfsoc_rtc_iobrg_writel()

commit b1999477 ("ARM: prima2: move to use REGMAP APIs for rtciobrg")
moves to regmap support, now we can move to use regmap APIs in RTC
driver.
Signed-off-by: Guo Zeng <guo.zeng@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

rtc-opal driver provides support for rtc alarms via
timed-power-on(tpo). However some Power platforms like BML use a fake
rtc clock and don't support tpo. Such platforms are indicated by the
missing 'has-tpo' property in the device tree.

Current implementation however enables callback for
rtc_class_ops.read/set alarm irrespective of the tpo support from the
platform. This results in a failed opal call when kernel tries to read
an existing alarms via opal_get_tpo_time during rtc device registration.

This patch fixes this issue by setting opal_rtc_ops.read/set_alarm
callback pointers only when tpo is supported.
Acked-by: Michael Neuling <mikey@neuling.org>
Acked-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Add driver for the RTC found on NXP LPC178x/18xx/408x/43xx devices.
The RTC provides calendar and clock functionality together with
alarm interrupt support.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Document NXP LPC178x/18xx/408x/43xx bindings
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The PCF2127 datasheet states that it's wrong to say that the date in
unreliable if BLF (battery low flag) is set but instead, OSF (seconds
register) should be used to check if oscillator, for any reason, stopped.
Battery may be low (usually below 2V5 threshold) but the date may be anyway
correct (typically date is unreliable when input voltage is below 1V2).
Signed-off-by: Andrea Scian <andrea.scian@dave.eu>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

There's a wrong comment in some RTC drivers that say it's better to ignore
rtc_valid_tm() when reading RTC timestamp. However this is wrong and is
better to return to the userspace the error if timestamp is not valid.
Signed-off-by: Andrea Scian <andrea.scian@dave.eu>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Along with DT support, this patch also cleans up the unnecessary
code around 'rtc_wakeup' initialization.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

removing below static analysis error:
(error) Possible null pointer dereference: client

if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C))
							^^^^^^^
Error comes because client is dereferenced before NULL check.
So probably NULL this check is not required.
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Use module_platform_driver for drivers whose init and exit functions
only register and unregister, respectively.

A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:

@A@
identifier f, x;
@@
-static f(...) { return platform_driver_register(&x); }

@b depends on a@
identifier e, a.x;
@@
-static e(...) { platform_driver_unregister(&x); }

@c depends on a && b@
identifier a.f;
declarer name module_init;
@@
-module_init(f);

@d depends on a && b && c@
identifier b.e, a.x;
declarer name module_exit;
declarer name module_platform_driver;
@@
-module_exit(e);
+module_platform_driver(x);
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

With the recent pinctrl-single changes, SoCs such as Texas
Instrument's OMAP processors can treat wake-up events from deeper idle
states as interrupts.

Let's add support for the optional second interrupt for wake-up using
the generic wakeirq support added in commit 4990d4fe ("PM /
Wakeirq: Add automated device wake IRQ handling")

Finally, to pass the wake-up interrupt in the dts file,
interrupts-extended property needs to be passed.

This is similar in approach to commit 2a0b965c ("serial: omap: Add
support for optional wake-up") + ee83bd3b ("serial: omap: Switch
wake-up interrupt to generic wakeirq")
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

It is always a good practice to keep the #includes sorted
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Since we are not doing anything fancy in remove function that requires
us to sequence IRQ free operation, we might as well switch over to devm_
equivalent of managed IRQ allocation and remove the explicit free_irq
since it'd be done automatically at remove.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The driver currently emulates the concept of threaded IRQ using a
workqueue, which it really does not need to. Instead, switch over to
threaded_irq handlers which is meant precisely for the same purpose.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Pull drm updates from Dave Airlie:
 "This is the main pull request for the drm for 4.3.  Nouveau is
  probably the biggest amount of changes in here, since it missed 4.2.
  Highlights below, along with the usual bunch of fixes.

  All stuff outside drm should have applicable acks.

  Highlights:

   - new drivers:
        freescale dcu kms driver

   - core:
        more atomic fixes
        disable some dri1 interfaces on kms drivers
        drop fb panic handling, this was just getting more broken, as more locking was required.
        new core fbdev Kconfig support - instead of each driver enable/disabling it
        struct_mutex cleanups

   - panel:
        more new panels
        cleanup Kconfig

   - i915:
        Skylake support enabled by default
        legacy modesetting using atomic infrastructure
        Skylake fixes
        GEN9 workarounds

   - amdgpu:
        Fiji support
        CGS support for amdgpu
        Initial GPU scheduler - off by default
        Lots of bug fixes and optimisations.

   - radeon:
        DP fixes
        misc fixes

   - amdkfd:
        Add Carrizo support for amdkfd using amdgpu.

   - nouveau:
        long pending cleanup to complete driver,
        fully bisectable which makes it larger,
        perfmon work
        more reclocking improvements
        maxwell displayport fixes

   - vmwgfx:
        new DX device support, supports OpenGL 3.3
        screen targets support

   - mgag200:
        G200eW support
        G200e new revision support

   - msm:
        dragonboard 410c support, msm8x94 support, msm8x74v1 support
        yuv format support
        dma plane support
        mdp5 rotation
        initial hdcp

   - sti:
        atomic support

   - exynos:
        lots of cleanups
        atomic modesetting/pageflipping support
        render node support

   - tegra:
        tegra210 support (dc, dsi, dp/hdmi)
        dpms with atomic modesetting support

   - atmel:
        support for 3 more atmel SoCs
        new input formats, PRIME support.

   - dwhdmi:
        preparing to add audio support

   - rockchip:
        yuv plane support"

* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1369 commits)
  drm/amdgpu: rename gmc_v8_0_init_compute_vmid
  drm/amdgpu: fix vce3 instance handling
  drm/amdgpu: remove ib test for the second VCE Ring
  drm/amdgpu: properly enable VM fault interrupts
  drm/amdgpu: fix warning in scheduler
  drm/amdgpu: fix buffer placement under memory pressure
  drm/amdgpu/cz: fix cz_dpm_update_low_memory_pstate logic
  drm/amdgpu: fix typo in dce11 watermark setup
  drm/amdgpu: fix typo in dce10 watermark setup
  drm/amdgpu: use top down allocation for non-CPU accessible vram
  drm/amdgpu: be explicit about cpu vram access for driver BOs (v2)
  drm/amdgpu: set MEC doorbell range for Fiji
  drm/amdgpu: implement burst NOP for SDMA
  drm/amdgpu: add insert_nop ring func and default implementation
  drm/amdgpu: add amdgpu_get_sdma_instance helper function
  drm/amdgpu: add AMDGPU_MAX_SDMA_INSTANCES
  drm/amdgpu: add burst_nop flag for sdma
  drm/amdgpu: add count field for the SDMA NOP packet v2
  drm/amdgpu: use PT for VM sync on unmap
  drm/amdgpu: make wait_event uninterruptible in push_job
  ...

A few more fixes for amdgpu from the last few days:
- Fix several copy paste typos
- Resume from suspend fixes for VCE
- Fix the GPU scheduler warning in kfifo_out
- Re-enable GPUVM fault interrupts which were inadvertently disabled
- GPUVM page table hang fix when paging

* 'drm-next-4.3' of git://people.freedesktop.org/~agd5f/linux:
  drm/amdgpu: rename gmc_v8_0_init_compute_vmid
  drm/amdgpu: fix vce3 instance handling
  drm/amdgpu: remove ib test for the second VCE Ring
  drm/amdgpu: properly enable VM fault interrupts
  drm/amdgpu: fix warning in scheduler
  drm/amdgpu: fix buffer placement under memory pressure
  drm/amdgpu/cz: fix cz_dpm_update_low_memory_pstate logic
  drm/amdgpu: fix typo in dce11 watermark setup
  drm/amdgpu: fix typo in dce10 watermark setup
  drm/amdgpu: use top down allocation for non-CPU accessible vram
  drm/amdgpu: be explicit about cpu vram access for driver BOs (v2)

It should be gfx_v8_0_init_compute_vmid since it's
part of the gfx block.
Acked-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Need to properly handle the instances for the idle
checks and soft reset.
Acked-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

it seems the VCE ring 1 ib test not reliable, remove it for now.
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Tested-and-Reviewed-by: Sonny Jiang <sonny.jiang@amd.com>

This fixes not printing VM faults.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

Pull input subsystem updates from Dmitry Torokhov:
 "Drivers, drivers, drivers...  No interesting input core changes this
  time"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (74 commits)
  Input: elan_i2c - use iap_version to get firmware information
  Input: max8997_haptic - fix module alias
  Input: elan_i2c - fix typos for validpage_count
  Input: psmouse - add small delay for IBM trackpoint pass-through mode
  Input: synaptics - fix handling of disabling gesture mode
  Input: elan_i2c - enable ELAN0100 acpi panels
  Input: gpio-keys - report error when disabling unsupported key
  Input: sur40 - fix error return code
  Input: sentelic - silence some underflow warnings
  Input: zhenhua - switch to using bitrev8()
  Input: cros_ec_keyb - replace KEYBOARD_CROS_EC dependency
  Input: cap11xx - add LED support
  Input: elants_i2c - fix for devm_gpiod_get API change
  Input: elan_i2c - enable asynchronous probing
  Input: elants_i2c - enable asynchronous probing
  Input: elants_i2c - wire up regulator support
  Input: do not emit unneeded EV_SYN when suspending
  Input: elants_i2c - disable idle mode before updating firmware
  MAINTAINERS: Add maintainer for atmel_mxt_ts
  Input: atmel_mxt_ts - remove warning on zero T44 count
  ...

Pull sound updates from Takashi Iwai:
 "There are little changes in core part, but lots of development are
  found in drivers, especially ASoC.  The diffstat shows regmap-related
  changes for a slight API additions / changes, and that's all.

  Looking at the code size statistics, the most significant addition is
  for Intel Skylake.  (Note that SKL support is still underway, the
  codec driver is missing.) Also STI controller driver is a major
  addition as well as a few new codec drivers.

  In HD-audio side, there are fewer changes than the past.  The
  noticeable change is the support of ELD notification from i915
  graphics driver.  Thus this pull request carries a few changes in
  drm/i915.

  Other than that, USB-audio got a rewrite of runtime PM code.  It was
  initiated by lockdep warning, but resulted in a good cleanup in the
  end.

  Below are the highlights:

  Common:
   - Factoring out of AC'97 reset code from ASoC into the core helper
   - A few regmap API extensions (in case it's not pulled yet)

  ASoC:
   - New drivers for Cirrus CS4349, GTM601, InvenSense ICS43432, Realtek
     RT298 and ST STI controllers
   - Machine drivers for Rockchip systems with MAX98090 and RT5645 and
     RT5650
   - Initial driver support for Intel Skylake devices
   - Lots of rsnd cleanup and enhancements
   - A few DAPM fixes and cleanups
   - A large number of cleanups in various drivers (conversion and
     standardized to regmap, component) mostly by Lars-Peter and Axel

  HD-audio:
   - Extended HD-audio core for Intel Skylake controller support
   - Quirks for Dell headsets, Alienware 15
   - Clean up of pin-based quirk tables for Realtek codecs
   - ELD notifier implenetation for Intel HDMI/DP

  USB-audio:
   - Refactor runtime PM code to make lockdep happier"

* tag 'sound-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (411 commits)
  drm/i915: Add locks around audio component bind/unbind
  drm/i915: Drop port_mst_index parameter from pin/eld callback
  ALSA: hda - Fix missing inline for dummy snd_hdac_set_codec_wakeup()
  ALSA: hda - Wake the codec up on pin/ELD notify events
  ALSA: hda - allow codecs to access the i915 pin/ELD callback
  drm/i915: Call audio pin/ELD notify function
  drm/i915: Add audio pin sense / ELD callback
  ASoC: zx296702-i2s: Fix resource leak when unload module
  ASoC: sti_uniperif: Ensure component is unregistered when unload module
  ASoC: au1x: psc-i2s: Convert to use devm_ioremap_resource
  ASoC: sh: dma-sh7760: Convert to devm_snd_soc_register_platform
  ASoC: spear_pcm: Use devm_snd_dmaengine_pcm_register to fix resource leak
  ALSA: fireworks/bebob/dice/oxfw: fix substreams counting at vmalloc failure
  ASoC: Clean up docbook warnings
  ASoC: txx9: Convert to devm_snd_soc_register_platform
  ASoC: pxa: Convert to devm_snd_soc_register_platform
  ASoC: nuc900: Convert to devm_snd_soc_register_platform
  ASoC: blackfin: Convert to devm_snd_soc_register_platform
  ASoC: au1x: Convert to devm_snd_soc_register_platform
  ASoC: qcom: Constify asoc_qcom_lpass_cpu_dai_ops
  ...

Pull backlight updates from Lee Jones:
 - Stop using LP855X Platform Data to control regulators
 - Move PWM8941 WLED driver into Backlight
 - Remove invalid use of IS_ERR_VALUE() macro
 - Remove duplicate check for NULL data before unregistering
 - Export I2C Device ID structure

* tag 'backlight-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
  backlight: tosa: Export I2C module alias information
  backlight: lp8788_bl: Delete a check before backlight_device_unregister()
  backlight: sky81452: Remove unneeded use of IS_ERR_VALUE() macro
  backlight: pm8941-wled: Move PM8941 WLED driver to backlight
  backlight: lp855x: Use private data for regulator control

Pull MFD updates from Lee Jones:
 "New Device Support:
   - New Clocksource driver from ST
   - New MFD/ACPI/DMA drivers for Intel's Sunrisepoint PCH based platforms
   - Add support for Arizona WM8998 and WM1814
   - Add support for Dialog Semi DA9062 and DA9063
   - Add support for Kontron COMe-bBL6 and COMe-cBW6
   - Add support for X-Powers AXP152
   - Add support for Atmel, many
   - Add support for STMPE, many
   - Add support for USB in X-Powers AXP22X

  Core Frameworks:
   - New Base API to traverse devices and their children in reverse order

  Bug Fixes:
   - Fix race between runtime-suspend and IRQs
   - Obtain platform data form more reliable source

  Fix-ups:
   - Constifying things
   - Variable signage changes
   - Kconfig depends|selects changes
   - Make use of BIT() macro
   - Do not supply .owner attribute in *_driver structures
   - MAINTAINERS entries
   - Stop using set_irq_flags()
   - Start using irq_set_chained_handler_and_data()
   - Export DT device ID structures"

* tag 'mfd-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (69 commits)
  mfd: jz4740-adc: Init mask cache in generic IRQ chip
  mfd: cros_ec: spi: Add OF match table
  mfd: stmpe: Add OF match table
  mfd: max77686: Split out regulator part from the DT binding
  mfd: Add DT binding for Maxim MAX77802 IC
  mfd: max77686: Use a generic name for the PMIC node in the example
  mfd: max77686: Don't suggest in binding to use a deprecated property
  mfd: Add MFD_CROS_EC dependencies
  mfd: cros_ec: Remove CROS_EC_PROTO dependency for SPI and I2C drivers
  mfd: axp20x: Add a cell for the usb power_supply part of the axp20x PMICs
  mfd: axp20x: Add missing registers, and mark more registers volatile
  mfd: arizona: Fixup some formatting/white space errors
  mfd: wm8994: Fix NULL pointer exception on missing pdata
  of: Add vendor prefix for Nuvoton
  mfd: mt6397: Implement wake handler and suspend/resume to handle wake up event
  mfd: atmel-hlcdc: Add support for new SoCs
  mfd: Export OF module alias information in missing drivers
  mfd: stw481x: Export I2C module alias information
  mfd: da9062: Support for the DA9063 OnKey in the DA9062 core
  mfd: max899x: Avoid redundant irq_data lookup
  ...

Pull dmaengine updates from Vinod Koul:
 "This time we have aded a new capability for scatter-gathered memset
  using dmaengine APIs.  This is supported in xdmac & hdmac drivers

  We have added support for reusing descriptors for examples like video
  buffers etc.  Driver will follow

  The behaviour of descriptor ack has been clarified and documented

  New devices added are:
   - dma controller in sun[457]i SoCs
   - lpc18xx dmamux
   - ZTE ZX296702 dma controller
   - Analog Devices AXI-DMAC DMA controller
   - eDMA support for dma-crossbar
   - imx6sx support in imx-sdma driver
   - imx-sdma device to device support

  Other:
   - jz4780 fixes
   - ioatdma large refactor and cleanup for removal of ioat v1 and v2
     which is deprecated and fixes
   - ACPI support in X-Gene DMA engine driver
   - ipu irq fixes
   - mvxor fixes
   - minor fixes spread thru drivers"

[ The Kconfig and Makefile entries got re-sorted alphabetically, and I
  handled the conflict with the new Intel integrated IDMA driver by
  slightly mis-sorting it on purpose: "IDMA64" got sorted after "IMX" in
  order to keep the Intel entries together.  I think it might be a good
  idea to just rename the IDMA64 config entry to INTEL_IDMA64 to make
  the sorting be a true sort, not this mismash.

  Also, this merge disables the COMPILE_TEST for the sun4i DMA
  controller, because it does not compile cleanly at all.     - Linus ]

* tag 'dmaengine-4.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (89 commits)
  dmaengine: ioatdma: add Broadwell EP ioatdma PCI dev IDs
  dmaengine :ipu: change ipu_irq_handler() to remove compile warning
  dmaengine: ioatdma: Fix variable array length
  dmaengine: ioatdma: fix sparse "error" with prep lock
  dmaengine: hdmac: Add memset capabilities
  dmaengine: sort the sh Makefile
  dmaengine: sort the sh Kconfig
  dmaengine: sort the dw Kconfig
  dmaengine: sort the Kconfig
  dmaengine: sort the makefile
  drivers/dma: make mv_xor.c driver explicitly non-modular
  dmaengine: Add support for the Analog Devices AXI-DMAC DMA controller
  devicetree: Add bindings documentation for Analog Devices AXI-DMAC
  dmaengine: xgene-dma: Fix the lock to allow client for further submission of requests
  dmaengine: ioatdma: fix coccinelle warning
  dmaengine: ioatdma: fix zero day warning on incompatible pointer type
  dmaengine: tegra-apb: Simplify locking for device using global pause
  dmaengine: tegra-apb: Remove unnecessary return statements and variables
  dmaengine: tegra-apb: Avoid unnecessary channel base address calculation
  dmaengine: tegra-apb: Remove unused variables
  ...

Pull pin control updates from Linus Walleij:
 "This is the bulk of pin control changes for the v4.3 development
  cycle.

  Like with GPIO it's a lot of stuff.  If my subsystems are any sign of
  the overall tempo of the kernel v4.3 will be a gigantic diff.

[ It looks like 4.3 is calmer than 4.2 in most other subsystems, but
  we'll see - Linus ]

  Core changes:

   - It is possible configure groups in debugfs.

   - Consolidation of chained IRQ handler install/remove replacing all
     call sites where irq_set_handler_data() and
     irq_set_chained_handler() were done in succession with a combined
     call to irq_set_chained_handler_and_data().  This series was
     created by Thomas Gleixner after the problem was observed by
     Russell King.

   - Tglx also made another series of patches switching
     __irq_set_handler_locked() for irq_set_handler_locked() which is
     way cleaner.

   - Tglx also wrote a good bunch of patches to make use of
     irq_desc_get_xxx() accessors and avoid looking up irq_descs from
     IRQ numbers.  The goal is to get rid of the irq number from the
     handlers in the IRQ flow which is nice.

  Driver feature enhancements:

   - Power management support for the SiRF SoC Atlas 7.

   - Power down support for the Qualcomm driver.

   - Intel Cherryview and Baytrail: switch drivers to use raw spinlocks
     in IRQ handlers to play nice with the realtime patch set.

   - Rework and new modes handling for Qualcomm SPMI-MPP.

   - Pinconf power source config for SH PFC.

  New drivers and subdrivers:

   - A new driver for Conexant Digicolor CX92755.

   - A new driver for UniPhier PH1-LD4, PH1-Pro4, PH1-sLD8, PH1-Pro5,
     ProXtream2 and PH1-LD6b SoC pin control support.

   - Reverse-egineered the S/PDIF settings for the Allwinner sun4i
     driver.

   - Support for Qualcomm Technologies QDF2xxx ARM64 SoCs

   - A new Freescale i.mx6ul subdriver.

  Cleanup:

   - Remove platform data support in a number of SH PFC subdrivers"

* tag 'pinctrl-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (95 commits)
  pinctrl: at91: fix null pointer dereference
  pinctrl: mediatek: Implement wake handler and suspend resume
  pinctrl: mediatek: Fix multiple registration issue.
  pinctrl: sh-pfc: r8a7794: add USB pin groups
  pinctrl: at91: Use generic irq_{request,release}_resources()
  pinctrl: cherryview: Use raw_spinlock for locking
  pinctrl: baytrail: Use raw_spinlock for locking
  pinctrl: imx6ul: Remove .owner field
  pinctrl: zynq: Fix typos in smc0_nand_grp and smc0_nor_grp
  pinctrl: sh-pfc: Implement pinconf power-source param for voltage switching
  clk: rockchip: add pclk_pd_pmu to the list of rk3288 critical clocks
  pinctrl: sun4i: add spdif to pin description.
  pinctrl: atlas7: clear ugly branch statements for pull and drivestrength
  pinctrl: baytrail: Serialize all register access
  pinctrl: baytrail: Drop FSF mailing address
  pinctrl: rockchip: only enable gpio clock when it setting
  pinctrl/mediatek: fix spelling mistake in dev_err error message
  pinctrl: cherryview: Serialize all register access
  pinctrl: UniPhier: PH1-Pro5: add I2C ch6 pin-mux setting
  pinctrl: nomadik: reflect current input value
  ...

Pull GPIO updates from Linus Walleij:
 "This is the bulk of GPIO changes for the v4.3 kernel cycle.

  There is quite a lot going on in the GPIO subsystem this merge window,
  so the main matter is decribed below.

  The hits in other subsystems when making the GPIO flags optional are
  all ACKed by their respective subsystem maintainers.

  Core changes:

   - Root out the wrapper devm_gpiod_get() and gpiod_get() etc versions
     of the descriptor calls that did not use the flags argument on the
     end.  This was around for too long and eventually Uwe Kleine-König
     took the time to clean it out and the last users are removed along
     with the macros in this tag.  In several cases the use of flags
     simplifies the code.  For this reason we have (ACKed) patches
     hitting in DRM, IIO, media, NFC, USB+PHY up until we hammer in the
     nail with removing the macros.

   - Add a fat document describing how much ready-made GPIO stuff we
     have i the kernel to discourage people from reinventing a square
     wheel in userspace, as so often happens.

   - Create a separate lockdep class for each instance of a GPIO IRQ
     chip instead of using one class for all chips, as the current code
     will not work with systems with several GPIO chips doing lockdep
     debugging.

   - Protect against driver unloading also when a GPIO line is only used
     as IRQ for the GPIOLIB_IRQCHIP helpers.

   - If the GPIO chip has no designated owner, assign the parent device
     driver owner as owner.

   - Consolidation of chained IRQ handler install/remove replacing all
     call sites where irq_set_handler_data() and
     irq_set_chained_handler() were done in succession with a combined
     call to irq_set_chained_handler_and_data().

     This series was created by Thomas Gleixner after the problem was
     observed by Russell King.

   - Tglx also made another series of patches switching
     __irq_set_handler_locked() for irq_set_handler_locked() which is
     way cleaner.

   - Tglx and Jiang Liu wrote a good bunch of patches to make use of
     irq_desc_get_xxx() accessors and avoid looking up irq_descs from
     IRQ numbers.  The goal is to get rid of the irq number from the
     handlers in the IRQ flow which is nice.

   - Rob Herring killed off the set_irq_flags() for all GPIO drivers.
     This was an ARM specific function that is replaced with the generic
     irq_modify_status() where special flags are actually needed.

   - When an OF node has a pin range for its GPIOs, return -EPROBE_DEFER
     if the pin controller isn't available.  Pretty logical, yet needed
     to be fixed.

   - If a driver using GPIOLIB_IRQCHIP has its own irq_*_resources call
     back, then call these instead of the defaults provided by the
     GPIOLIB.

   - Fix an undocumented ABI hole: named GPIOs were not properly
     documented.

  Driver improvements:

   - Add get_direction() support to the generic GPIO driver, it's
     strange that we didn't have that before.

   - Make it possible to have input-only GPIO chips using the generic
     GPIO driver.

   - Clean out platform data support from the Emma Mobile (EM) driver

   - Finegrained runtime PM support for the RCAR driver.

   - Support r8a7795 (R-car H3) in the RCAR driver.

   - Support interrupts on GPIOs 16 thru 31 in the DaVinci driver.

   - Some consolidation and new support in the MPC8xxx driver, we now
     support MPC5125.

   - Preempt-RT-friendly patches: the OMAP, MPC8xxx, drivers uses raw
     spinlocks making it work better with the realime patches.

   - Interrupt support for the EXTRAXFS GPIO driver.

   - Make the ETRAXFS GPIO driver support also ARTPEC-3.

   - Interrupt and wakeup support for the BRCMSTB driver, also for
     wakeup from S5 cold boot.

   - Mask MXC IRQs during suspend.

   - Improve OMAP2 GPIO set_debounce() to work according to spec.

   - The VF610 driver handles IRQs properly.

  New drivers:

   - ZTE ZX GPIO driver"

* tag 'gpio-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (87 commits)
  Revert "gpio: extraxfs: fix returnvar.cocci warnings"
  gpio: tc3589x: use static container helper
  gpio: xlp: fix error return code
  gpio: vf610: handle level IRQ's properly
  gpio: max732x: Fix error handling in probe()
  gpio: omap: fix clk_prepare/unprepare usage
  gpio: omap: protect regs access in omap_gpio_irq_handler
  gpio: omap: fix omap2_set_gpio_debounce
  gpio: omap: switch to use platform_get_irq
  gpio: omap: remove wrong irq_domain_remove usage in probe
  gpiolib: add description for gpio irqchip fields in struct gpio_chip
  gpio: extraxfs: fix returnvar.cocci warnings
  gpiolib: irqchip: use different lockdep class for each gpio irqchip
  gpio/grgpio: fix deadlock in grgpio_irq_unmap()
  Documentation: gpio: consumer: describe active low property
  gpio: mxc: fix section mismatch warning
  gpio/mxc: mask gpio interrupts in suspend
  gpio: omap: Fix missing raw locks conversion
  gpio: brcmstb: support wakeup from S5 cold boot
  gpio: brcmstb: Add interrupt and wakeup source support
  ...

Pull tile updates from Chris Metcalf:
 "This includes secure computing support as well as miscellaneous minor
  improvements"

* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  tile: correct some typos in opcode type names
  tile/vdso: emit a GNU hash as well
  tile: Remove finish_arch_switch
  tile: enable full SECCOMP support
  tile/time: Migrate to new 'set-state' interface