On some hardware/driver/architecture combinations, it may take longer
than 200msec for all close operations to be completed, causing a
spurious error message to be logged.

Increase the timeout value to 500msec to avoid this erroneous error.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The counter variable in iavf_clean_tx_irq starts out negative and climbs
to 0. So allocating it as u16 is actually a really bad idea that just
happens to work because the value underflows and overflows consistently
on most architectures.

Replace the u16 with an int so signed math works as expected.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch changes how VLAN tag are being populated and programmed into
the HW - Instead of start adding VF VLAN tag from the last member of the
element list, start from the first member of the list, until number of
allowed VLAN tags is exhausted in the HW.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently user is unable to delete the filter. See following example:
$ tc filter add dev ens16np1 ingress pref 1 handle 1 matchall action drop
$ tc filter show dev ens16np1 ingress
filter protocol all pref 1 matchall chain 0
filter protocol all pref 1 matchall chain 0 handle 0x1
  in_hw
        action order 1: gact action drop
         random type none pass val 0
         index 1 ref 1 bind 1

$ tc filter del dev ens16np1 ingress pref 1 handle 1 matchall action drop
RTNETLINK answers: Operation not supported

Implement tcf_proto_ops->delete() op and allow user to delete the filter.
Reported-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pointer ae_dev is null checked however, prior to that it is dereferenced
when assigned pointer ops. Fix this by assigning pointer ops after ae_dev
has been null checked.

Addresses-Coverity: ("Dereference before null check")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kevin Darbyshire-Bryant says:

====================
net: sched: act_ctinfo: fixes

This is first attempt at sending a small series.  Order is important
because one bug (policy validation) prevents us from encountering the
more important 'OOPS' generating bug in action creation.  Fix the OOPS
first.

Confession time: Until very recently, development of this module has
been done on 'net-next' tree to 'clean compile' level with run-time
testing on backports to 4.14 & 4.19 kernels under openwrt.  It turns out
that sched: action: based code has been under more active change than I
realised.

During the back & forward porting during development & testing, the
critical ACT_P_CREATED return code got missed despite being in the 4.14
& 4.19 backports.  I have now gone through the init functions, using
act_csum as reference with a fine toothed comb and am happy they do the
same things.

This issue hadn't been caught till now due to another issue caused by
new strict nla_parse_nested function failing parsing validation before
action creation.

Thanks to Marcelo Leitner <marcelo.leitner@gmail.com> for flagging
extack deficiency (fixed in 733f0766 sched: act_ctinfo: use extack
error reporting) which led to b424e432 ("netlink: add validation of
NLA_F_NESTED flag") and 8cb08174 ("netlink: make validation more
configurable for future strictness”) which led to the policy validation
fix, which then led to the action creation fix both contained in this
series.

If I ever get to a developer conference please feel free to
tar/feather/apply cone of shame.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix nla_policy definition by specifying an exact length type attribute
to CTINFO action paraneter block structure.  Without this change,
netlink parsing will fail validation and the action will not be
instantiated.

8cb08174 ("netlink: make validation more configurable for future")
introduced much stricter checking to attributes being passed via
netlink.  Existing actions were updated to use less restrictive
deprecated versions of nla_parse_nested.

As a new module, act_ctinfo should be designed to use the strict
checking model otherwise, well, what was the point of implementing it.

Confession time: Until very recently, development of this module has
been done on 'net-next' tree to 'clean compile' level with run-time
testing on backports to 4.14 & 4.19 kernels under openwrt.  This is how
I managed to miss the run-time impacts of the new strict
nla_parse_nested function.  I hopefully have learned something from this
(glances toward laptop running a net-next kernel)

There is however a still outstanding implication on iproute2 user space
in that it needs to be told to pass nested netlink messages with the
nested attribute actually set.  So even with this kernel fix to do
things correctly you still cannot instantiate a new 'strict'
nla_parse_nested based action such as act_ctinfo with iproute2's tc.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use correct return value on action creation: ACT_P_CREATED.

The use of incorrect return value could result in a situation where the
system thought a ctinfo module was listening but actually wasn't
instantiated correctly leading to an OOPS in tcf_generic_walker().

Confession time: Until very recently, development of this module has
been done on 'net-next' tree to 'clean compile' level with run-time
testing on backports to 4.14 & 4.19 kernels under openwrt.  During the
back & forward porting during development & testing, the critical
ACT_P_CREATED return code got missed despite being in the 4.14 & 4.19
backports.  I have now gone through the init functions, using act_csum
as reference with a fine toothed comb.  Bonus, no more OOPSes.  I
managed to also miss this issue till now due to the new strict
nla_parse_nested function failing validation before action creation.

As an inexperienced developer I've learned that
copy/pasting/backporting/forward porting code correctly is hard.  If I
ever get to a developer conference I shall don the cone of shame.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vhost_net was known to suffer from HOL[1] issues which is not easy to
fix. Several downstream disable the feature by default. What's more,
the datapath was split and datacopy path got the support of batching
and XDP support recently which makes it faster than zerocopy part for
small packets transmission.

It looks to me that disable zerocopy by default is more
appropriate. It cold be enabled by default again in the future if we
fix the above issues.

[1] https://patchwork.kernel.org/patch/3787671/Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Using a bare block cipher in non-crypto code is almost always a bad idea,
not only for security reasons (and we've seen some examples of this in
the kernel in the past), but also for performance reasons.

In the TCP fastopen case, we call into the bare AES block cipher one or
two times (depending on whether the connection is IPv4 or IPv6). On most
systems, this results in a call chain such as

  crypto_cipher_encrypt_one(ctx, dst, src)
    crypto_cipher_crt(tfm)->cit_encrypt_one(crypto_cipher_tfm(tfm), ...);
      aesni_encrypt
        kernel_fpu_begin();
        aesni_enc(ctx, dst, src); // asm routine
        kernel_fpu_end();

It is highly unlikely that the use of special AES instructions has a
benefit in this case, especially since we are doing the above twice
for IPv6 connections, instead of using a transform which can process
the entire input in one go.

We could switch to the cbcmac(aes) shash, which would at least get
rid of the duplicated overhead in *some* cases (i.e., today, only
arm64 has an accelerated implementation of cbcmac(aes), while x86 will
end up using the generic cbcmac template wrapping the AES-NI cipher,
which basically ends up doing exactly the above). However, in the given
context, it makes more sense to use a light-weight MAC algorithm that
is more suitable for the purpose at hand, such as SipHash.

Since the output size of SipHash already matches our chosen value for
TCP_FASTOPEN_COOKIE_SIZE, and given that it accepts arbitrary input
sizes, this greatly simplifies the code as well.

NOTE: Server farms backing a single server IP for load balancing purposes
      and sharing a single fastopen key will be adversely affected by
      this change unless all systems in the pool receive their kernel
      upgrades at the same time.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In patch series, commit 9195948f ("tipc: improve TIPC throughput by
Gap ACK blocks"), as for simplicity, the repeated retransmit failures'
detection in the function - "tipc_link_retrans()" was kept there for
broadcast retransmissions only.

This commit now reapplies this feature for link unicast retransmissions
that has been done via the function - "tipc_link_advance_transmq()".

Also, the "tipc_link_retrans()" is renamed to "tipc_link_bc_retrans()"
as it is used only for broadcast.
Acked-by: Jon Maloy <jon.maloy@ericsson.se>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Like bond, add ethtool get_link_ksettings to show the total speed.

v2: no update, just repost.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One warning each on signedness, unused variable and return type.

Fixes: 10fbcdd1 ("selftests/net: add TFO key rotation selftest")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replaced incorrect hard-coded function-name in error message with
__func__.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The EXPORT_SYMBOL for lapb_register was next to a different function.
Moved it to the right place.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

- Added index upper bound test case
- Added mark upper bound test case
- Re-worded descriptions to few cases for clarity
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This macro $IP will be used in upcoming tc tests, which require
to create interfaces etc.
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While data pass suspend, reuse of rx descriptors can be disabled using
channel state & lock from cpdma layer. For this, submit to a channel
has to be disabled using state != "not active" under lock, what is done
with this patch. The same submit is used to fill rx channel while
ndo_open, when channel is idled, so add idled submit routine that
allows to prepare descs for the channel. All this simplifies code and
helps to avoid dormant mode usage and send packets only to active
channels, avoiding potential race in later on changes. Also add missed
sync barrier analogically like in other places after stopping tx
queues.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Martin Blumenstingl says:

====================
stmmac: cleanups for stmmac_mdio_reset

This is a successor to my previous series "stmmac: honor the GPIO flags
for the PHY reset GPIO" from [0]. It contains only the "cleanup"
patches from that series plus some additional cleanups on top.

I broke out the actual GPIO flag handling into a separate patch which
is already part of net-next: "net: stmmac: use GPIO descriptors in
stmmac_mdio_reset" from [1]

I have build and runtime tested this on my ARM Meson8b Odroid-C1.

[0] https://patchwork.kernel.org/cover/10983801/
[1] https://patchwork.ozlabs.org/patch/1114798/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The phy_reset hook is not set anywhere. Drop it to make
stmmac_mdio_reset() smaller.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only OF platforms use the reset delays and these delays are only read in
stmmac_mdio_reset(). Move them from struct stmmac_mdio_bus_data to a
stack variable inside stmmac_mdio_reset() because that's the only usage
of these delays.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

No platform uses the "reset_gpio" field from stmmac_mdio_bus_data
anymore. Drop it so we don't get any new consumers either.

Plain GPIO numbers are being deprecated in favor of GPIO descriptors. If
needed any new non-OF platform can add a GPIO descriptor lookup table.
devm_gpiod_get_optional() will find the GPIO in that case.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change stmmac_mdio_reset() to use device_property_read_u32_array()
instead of of_property_read_u32_array().

This is meant as a cleanup because we can drop the struct device_node
variable. Also it will make it easier to get rid of struct
stmmac_mdio_bus_data (or at least make it private) in the future because
non-OF platforms can now pass the reset delays as device properties.

No functional changes (neither for OF platforms nor for ones that are
not using OF, because the modified code is still contained in an "if
(priv->device->of_node)").
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A simplified version of the existing code looks like this:
  if (priv->device->of_node) {
      struct device_node *np = priv->device->of_node;
      if (!np)
          return 0;

The second "if" never evaluates to true because the first "if" checks
for exactly the opposite.
Drop the redundant check and early return to make the code easier to
understand.

No functional changes intended.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This config option makes only couple of lines optional.
Two small helpers and an int in couple of cls structs.

Remove the config option and always compile this in.
This saves the user from unexpected surprises when he adds
a filter with ingress device match which is silently ignored
in case the config option is not set.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Abit Fatal1ty F-190HD has a PCI ID quirk and the entry marks this
board as not GBit-capable, what is wrong. According to [0] the board
has a RTL8111B that is GBit-capable, therefore remove the
RTL_CFG_NO_GBIT flag.

[0] https://www.centos.org/forums/viewtopic.php?t=23390Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Because of PHYLINK conversion we stopped parsing the phy-handle property
from DT. Unfortunatelly, some wrapper drivers still rely on this phy
node to configure the PHY.

Let's restore the parsing of PHY handle while these wrapper drivers are
not fully converted to PHYLINK.

Fixes: 74371272 ("net: stmmac: Convert to phylink and remove phylib logic")
Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yangbo Lu says:

====================
Reuse ptp_qoriq driver for dpaa2-ptp

Although dpaa2-ptp.c driver is a fsl_mc_driver which
is using MC APIs for register accessing, it's same IP
block with eTSEC/DPAA/ENETC 1588 timer.
This patch-set is to convert to reuse ptp_qoriq driver by
using register ioremap and dropping related MC APIs.
However the interrupts could only be handled by MC which
fires MSIs to ARM cores. So the interrupt enabling and
handling still rely on MC APIs. MC APIs for interrupt
and PPS event support are also added by this patch-set.

---
Changes for v2:
	- Allowed to compile with COMPILE_TEST.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Maintain DPAA2 PTP driver in QorIQ PTP entry.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to add interrupt support for dpaa2 ptp clock,
including MC APIs and PPS interrupt support. Other events
haven't been supported in MC by now.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to add ptp timer device tree node for dpaa2
platforms(ls1088a/ls208xa/lx2160a).
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new compatible for DPAA2 PTP.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Although dpaa2-ptp.c driver is a fsl_mc_driver which
is using MC APIs for register accessing, it's same IP
block with eTSEC/DPAA/ENETC 1588 timer.
This patch is to convert to reuse ptp_qoriq driver by
using register ioremap and dropping related MC APIs.
However the interrupts could only be handled by MC which
fires MSIs to ARM cores. So the interrupt enabling and
handling still rely on MC APIs.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to add QorIQ PTP support for DPAA2.
Although dpaa2-ptp.c driver is a fsl_mc_driver which
is using MC APIs for register accessing, it's same
IP block with eTSEC/DPAA/ENETC 1588 timer. We will
convert to reuse ptp_qoriq driver by using register
ioremap and dropping related MC APIs.
Also allow to compile ptp_qoriq with COMPILE_TEST.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

'devm_kasprintf' is less verbose than:
   snprintf(NULL, 0, ...);
   devm_kzalloc(...);
   sprintf
so use it instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 422efd03.

It breaks ipv6.
Signed-off-by: David S. Miller <davem@davemloft.net>

The DSA ports must flood unknown unicast and multicast, but the switch
must not flood the CPU ports with unknown multicast, as this results
in a lot of undesirable traffic that the network stack needs to filter
in software.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vivien Didelot says:

====================
net: dsa: use switchdev attr and obj handlers

This series reduces boilerplate in the handling of switchdev attribute and
object operations by using the switchdev_handle_* helpers, which check the
targeted devices and recurse into their lower devices.

This also brings back the ability to inspect operations targeting the bridge
device itself (where .orig_dev and .dev were originally the bridge device),
even though that is of no use yet and skipped by this series.

Changes in v2: Only VLAN and (non-host) MDB objects not directly targeting
the slave device are unsupported at the moment, so only skip these cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Get rid of the dsa_slave_switchdev_port_{attr_set,obj}_event functions
in favor of the switchdev_handle_port_{attr_set,obj_add,obj_del}
helpers which recurse into the lower devices of the target interface.

This has the benefit of being aware of the operations made on the
bridge device itself, where orig_dev is the bridge, and dev is the
slave. This can be used later to configure the hardware switches.

Only VLAN and (port) MDB objects not directly targeting the slave
device are unsupported at the moment, so skip this case in their
respective case statements.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The switchdev handle helpers make use of a device checking helper
requiring a const net_device. Make dsa_slave_dev_check compliant
to this.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>