Christopher reports that perf_event_print_debug() can crash in uniprocessor
builds.  The crash is due to pcr_ops being NULL.

This happens because pcr_arch_init() is only invoked by smp_cpus_done() which
only executes in SMP builds.

init_hw_perf_events() is closely intertwined with pcr_ops being setup properly,
therefore:

1) Call pcr_arch_init() early on from init_hw_perf_events(), instead of
   from smp_cpus_done().

2) Do not hook up a PMU type if pcr_ops is NULL after pcr_arch_init().

3) Move init_hw_perf_events to a later initcall so that it we will be
   sure to invoke pcr_arch_init() after all cpus are brought up.

Finally, guard the one naked sequence of pcr_ops dereferences in
__global_pmu_self() with an appropriate NULL check.
Reported-by: Christopher Alexander Tobias Schulze <cat.schulze@alice-dsl.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

nmi_cpu_busy() is a SMP function call that just makes sure that all of the
cpus are spinning using cpu cycles while the NMI test runs.

It does not need to disable IRQs because we just care about NMIs executing
which will even with 'normal' IRQs disabled.

It is not legal to enable hard IRQs in a SMP cross call, in fact this bug
triggers the BUG check in irq_work_run_list():

	BUG_ON(!irqs_disabled());

Because now irq_work_run() is invoked from the tail of
generic_smp_call_function_single_interrupt().
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

The prefix suggests the number should be printed in hex, so use
the %x specifier to do that.

Found by using regex suggested by Joe Perches.
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull IDE cleanup from David Miller:
 "Just one minor cleanup"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide:
  ide: use module_platform_driver()

Pull sparc updates from David Miller:

 1) Add sparc RAM output to /proc/iomem, from Bob Picco.

 2) Allow seeks on /dev/mdesc, from Khalid Aziz.

 3) Cleanup sparc64 I/O accessors, from Sam Ravnborg.

 4) If update_mmu_cache{,_pmd}() is called with an not-valid mapping, do
    not insert it into the TLB miss hash tables otherwise we'll
    livelock.  Based upon work by Christopher Alexander Tobias Schulze.

 5) Fix BREAK detection in sunsab driver when no actual characters are
    pending, from Christopher Alexander Tobias Schulze.

 6) Because we have modules --> openfirmware --> vmalloc ordering of
    virtual memory, the lazy VMAP TLB flusher can cons up an invocation
    of flush_tlb_kernel_range() that covers the openfirmware address
    range.  Unfortunately this will flush out the firmware's locked TLB
    mapping which causes all kinds of trouble.  Just split up the flush
    request if this happens, but in the long term the lazy VMAP flusher
    should probably be made a little bit smarter.

    Based upon work by Christopher Alexander Tobias Schulze.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next:
  sparc64: Fix up merge thinko.
  sparc: Add "install" target
  arch/sparc/math-emu/math_32.c: drop stray break operator
  sparc64: ldc_connect() should not return EINVAL when handshake is in progress.
  sparc64: Guard against flushing openfirmware mappings.
  sunsab: Fix detection of BREAK on sunsab serial console
  bbc-i2c: Fix BBC I2C envctrl on SunBlade 2000
  sparc64: Do not insert non-valid PTEs into the TSB hash table.
  sparc64: avoid code duplication in io_64.h
  sparc64: reorder functions in io_64.h
  sparc64: drop unused SLOW_DOWN_IO definitions
  sparc64: remove macro indirection in io_64.h
  sparc64: update IO access functions in PeeCeeI
  sparcspkr: use sbus_*() primitives for IO
  sparc: Add support for seek and shorter read to /dev/mdesc
  sparc: use %s for unaligned panic
  drivers/sbus/char: Micro-optimization in display7seg.c
  display7seg: Introduce the use of the managed version of kzalloc
  sparc64 - add mem to iomem resource

Pull networking updates from David Miller:
 "Highlights:

   1) Steady transitioning of the BPF instructure to a generic spot so
      all kernel subsystems can make use of it, from Alexei Starovoitov.

   2) SFC driver supports busy polling, from Alexandre Rames.

   3) Take advantage of hash table in UDP multicast delivery, from David
      Held.

   4) Lighten locking, in particular by getting rid of the LRU lists, in
      inet frag handling.  From Florian Westphal.

   5) Add support for various RFC6458 control messages in SCTP, from
      Geir Ola Vaagland.

   6) Allow to filter bridge forwarding database dumps by device, from
      Jamal Hadi Salim.

   7) virtio-net also now supports busy polling, from Jason Wang.

   8) Some low level optimization tweaks in pktgen from Jesper Dangaard
      Brouer.

   9) Add support for ipv6 address generation modes, so that userland
      can have some input into the process.  From Jiri Pirko.

  10) Consolidate common TCP connection request code in ipv4 and ipv6,
      from Octavian Purdila.

  11) New ARP packet logger in netfilter, from Pablo Neira Ayuso.

  12) Generic resizable RCU hash table, with intial users in netlink and
      nftables.  From Thomas Graf.

  13) Maintain a name assignment type so that userspace can see where a
      network device name came from (enumerated by kernel, assigned
      explicitly by userspace, etc.) From Tom Gundersen.

  14) Automatic flow label generation on transmit in ipv6, from Tom
      Herbert.

  15) New packet timestamping facilities from Willem de Bruijn, meant to
      assist in measuring latencies going into/out-of the packet
      scheduler, latency from TCP data transmission to ACK, etc"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1536 commits)
  cxgb4 : Disable recursive mailbox commands when enabling vi
  net: reduce USB network driver config options.
  tg3: Modify tg3_tso_bug() to handle multiple TX rings
  amd-xgbe: Perform phy connect/disconnect at dev open/stop
  amd-xgbe: Use dma_set_mask_and_coherent to set DMA mask
  net: sun4i-emac: fix memory leak on bad packet
  sctp: fix possible seqlock seadlock in sctp_packet_transmit()
  Revert "net: phy: Set the driver when registering an MDIO bus device"
  cxgb4vf: Turn off SGE RX/TX Callback Timers and interrupts in PCI shutdown routine
  team: Simplify return path of team_newlink
  bridge: Update outdated comment on promiscuous mode
  net-timestamp: ACK timestamp for bytestreams
  net-timestamp: TCP timestamping
  net-timestamp: SCHED timestamp on entering packet scheduler
  net-timestamp: add key to disambiguate concurrent datagrams
  net-timestamp: move timestamp flags out of sk_flags
  net-timestamp: extend SCM_TIMESTAMPING ancillary data struct
  cxgb4i : Move stray CPL definitions to cxgb4 driver
  tcp: reduce spurious retransmits due to transient SACK reneging
  qlcnic: Initialize dcbnl_ops before register_netdev
  ...

Pull randomness updates from Ted Ts'o:
 "Cleanups and bug fixes to /dev/random, add a new getrandom(2) system
  call, which is a superset of OpenBSD's getentropy(2) call, for use
  with userspace crypto libraries such as LibreSSL.

  Also add the ability to have a kernel thread to pull entropy from
  hardware rng devices into /dev/random"

* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
  hwrng: Pass entropy to add_hwgenerator_randomness() in bits, not bytes
  random: limit the contribution of the hw rng to at most half
  random: introduce getrandom(2) system call
  hw_random: fix sparse warning (NULL vs 0 for pointer)
  random: use registers from interrupted code for CPU's w/o a cycle counter
  hwrng: add per-device entropy derating
  hwrng: create filler thread
  random: add_hwgenerator_randomness() for feeding entropy from devices
  random: use an improved fast_mix() function
  random: clean up interrupt entropy accounting for archs w/o cycle counters
  random: only update the last_pulled time if we actually transferred entropy
  random: remove unneeded hash of a portion of the entropy pool
  random: always update the entropy pool under the spinlock

Pull security subsystem updates from James Morris:
 "In this release:

   - PKCS#7 parser for the key management subsystem from David Howells
   - appoint Kees Cook as seccomp maintainer
   - bugfixes and general maintenance across the subsystem"

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (94 commits)
  X.509: Need to export x509_request_asymmetric_key()
  netlabel: shorter names for the NetLabel catmap funcs/structs
  netlabel: fix the catmap walking functions
  netlabel: fix the horribly broken catmap functions
  netlabel: fix a problem when setting bits below the previously lowest bit
  PKCS#7: X.509 certificate issuer and subject are mandatory fields in the ASN.1
  tpm: simplify code by using %*phN specifier
  tpm: Provide a generic means to override the chip returned timeouts
  tpm: missing tpm_chip_put in tpm_get_random()
  tpm: Properly clean sysfs entries in error path
  tpm: Add missing tpm_do_selftest to ST33 I2C driver
  PKCS#7: Use x509_request_asymmetric_key()
  Revert "selinux: fix the default socket labeling in sock_graft()"
  X.509: x509_request_asymmetric_keys() doesn't need string length arguments
  PKCS#7: fix sparse non static symbol warning
  KEYS: revert encrypted key change
  ima: add support for measuring and appraising firmware
  firmware_class: perform new LSM checks
  security: introduce kernel_fw_from_file hook
  PKCS#7: Missing inclusion of linux/err.h
  ...

Eliminate boilerplate code by using module_platform_driver().
Signed-off-by: Christoph Jaeger <christophjaeger@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	arch/sparc/mm/init_64.c

Conflict was simple non-overlapping additions.
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/Makefile
	net/ipv6/sysctl_net_ipv6.c

Two ipv6_table_template[] additions overlap, so the index
of the ipv6_table[x] assignments needed to be adjusted.

In the drivers/net/Makefile case, we've gotten rid of the
garbage whereby we had to list every single USB networking
driver in the top-level Makefile, there is just one
"USB_NETWORKING" that guards everything.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull timer and time updates from Thomas Gleixner:
 "A rather large update of timers, timekeeping & co

   - Core timekeeping code is year-2038 safe now for 32bit machines.
     Now we just need to fix all in kernel users and the gazillion of
     user space interfaces which rely on timespec/timeval :)

   - Better cache layout for the timekeeping internal data structures.

   - Proper nanosecond based interfaces for in kernel users.

   - Tree wide cleanup of code which wants nanoseconds but does hoops
     and loops to convert back and forth from timespecs.  Some of it
     definitely belongs into the ugly code museum.

   - Consolidation of the timekeeping interface zoo.

   - A fast NMI safe accessor to clock monotonic for tracing.  This is a
     long standing request to support correlated user/kernel space
     traces.  With proper NTP frequency correction it's also suitable
     for correlation of traces accross separate machines.

   - Checkpoint/restart support for timerfd.

   - A few NOHZ[_FULL] improvements in the [hr]timer code.

   - Code move from kernel to kernel/time of all time* related code.

   - New clocksource/event drivers from the ARM universe.  I'm really
     impressed that despite an architected timer in the newer chips SoC
     manufacturers insist on inventing new and differently broken SoC
     specific timers.

[ Ed. "Impressed"? I don't think that word means what you think it means ]

   - Another round of code move from arch to drivers.  Looks like most
     of the legacy mess in ARM regarding timers is sorted out except for
     a few obnoxious strongholds.

   - The usual updates and fixlets all over the place"

* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
  timekeeping: Fixup typo in update_vsyscall_old definition
  clocksource: document some basic timekeeping concepts
  timekeeping: Use cached ntp_tick_length when accumulating error
  timekeeping: Rework frequency adjustments to work better w/ nohz
  timekeeping: Minor fixup for timespec64->timespec assignment
  ftrace: Provide trace clocks monotonic
  timekeeping: Provide fast and NMI safe access to CLOCK_MONOTONIC
  seqcount: Add raw_write_seqcount_latch()
  seqcount: Provide raw_read_seqcount()
  timekeeping: Use tk_read_base as argument for timekeeping_get_ns()
  timekeeping: Create struct tk_read_base and use it in struct timekeeper
  timekeeping: Restructure the timekeeper some more
  clocksource: Get rid of cycle_last
  clocksource: Move cycle_last validation to core code
  clocksource: Make delta calculation a function
  wireless: ath9k: Get rid of timespec conversions
  drm: vmwgfx: Use nsec based interfaces
  drm: i915: Use nsec based interfaces
  timekeeping: Provide ktime_get_raw()
  hangcheck-timer: Use ktime_get_ns()
  ...

Pull irq updates from Thomas Gleixner:
 "Nothing spectacular from the irq department this time:
   - overhaul of the crossbar chip driver
   - overhaul of the spear shirq chip driver
   - support for the atmel-aic chip
   - code move from arch to drivers
   - the usual tiny fixlets
   - two reverts worth to mention which undo the too simple attempt of
     supporting wakeup interrupts on shared interrupt lines"

* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (41 commits)
  Revert "irq: Warn when shared interrupts do not match on NO_SUSPEND"
  Revert "PM / sleep / irq: Do not suspend wakeup interrupts"
  irq: Warn when shared interrupts do not match on NO_SUSPEND
  irqchip: atmel-aic: Define irq fixups for atmel SoCs
  irqchip: atmel-aic: Implement RTC irq fixup
  irqchip: atmel-aic: Add irq fixup infrastructure
  irqchip: atmel-aic: Add atmel AIC/AIC5 drivers
  irqchip: atmel-aic: Move binding doc to interrupt-controller directory
  genirq: generic chip: Export irq_map_generic_chip function
  PM / sleep / irq: Do not suspend wakeup interrupts
  irqchip: or1k-pic: Migrate from arch/openrisc/
  irqchip: crossbar: Allow for quirky hardware with direct hardwiring of GIC
  documentation: dt: omap: crossbar: Add description for interrupt consumer
  irqchip: crossbar: Introduce centralized check for crossbar write
  irqchip: crossbar: Introduce ti, max-crossbar-sources to identify valid crossbar mapping
  irqchip: crossbar: Add kerneldoc for crossbar_domain_unmap callback
  irqchip: crossbar: Set cb pointer to null in case of error
  irqchip: crossbar: Change the goto naming
  irqchip: crossbar: Return proper error value
  irqchip: crossbar: Fix kerneldoc warning
  ...

Commit ea431643 ("x86/mce: Fix CMCI preemption bugs") breaks RT by
the completely unrelated conversion of the cmci_discover_lock to a
regular (non raw) spinlock.  This lock was annotated in commit
59d958d2 ("locking, x86: mce: Annotate cmci_discover_lock as raw")
with a proper explanation why.

The argument for converting the lock back to a regular spinlock was:

 - it does percpu ops without disabling preemption. Preemption is not
   disabled due to the mistaken use of a raw spinlock.

Which is complete nonsense.  The raw_spinlock is disabling preemption in
the same way as a regular spinlock.  In mainline spinlock maps to
raw_spinlock, in RT spinlock becomes a "sleeping" lock.

raw_spinlock has on RT exactly the same semantics as in mainline.  And
because this lock is taken in non preemptible context it must be raw on
RT.

Undo the locking brainfart.
Reported-by: Clark Williams <williams@redhat.com>
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Enabling a Virtual Interface can result in an interrupt during the processing
 of the VI Enable command and, in some paths, result in an attempt to issue
another command in the interrupt context, eventually crashing the system. Thus,
 we disable interrupts during the course of the VI Enable command and ensure
enable doesn't sleep.
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

USB network drivers are already handled in drivers/net/usb/Kconfig.
Let's save the maintenance burden of dependencies in drivers/net/Makefile.

The newly introduced USB_NET_DRIVERS umbrella config option defaults
to 'y' so as to minimize the changes of behavior.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3_tso_bug() was originally designed to handle only HW TX ring 0, Commit
d3f6f3a1 ("tg3: Prevent page allocation failure
during TSO workaround") changed the driver logic to use tg3_tso_bug() for all
HW TX rings that are enabled. This patch fixes the regression by modifying
tg3_tso_bug() to handle multiple HW TX rings.
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tom Lendacky says:

====================
amd-xgbe: AMD XGBE driver update 2014-08-05

The following series of patches includes fixes/updates to the driver.

- Use dma_set_mask_and_coherent to set the DMA mask
- Move the phy connect/disconnect logic to allow for module unloading

Changes in V2:
- Check the return value of the dma_set_mask_and_coherent call
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

A change added to the mdiobus/phy api added a module_get/module_put
during phy connect/disconnect processing. Currently, the driver
performs a phy connect during module probe and a phy disconnect during
module remove. With the addition of the module_get during phy connect
the amd-xgbe module use count is incremented and can no longer be
unloaded.

Move the phy connect/disconnect from the driver probe/remove functions
to the net_device_ops ndo_open/ndo_stop functions.  This allows the
module use count to be decremented when the device(s) are brought down
and allows the module to be unloaded.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the dma_set_mask_and_coherent function to set the DMA mask rather
than setting the DMA mask fields directly.  This was originally done
to work around a bug in the arm64 DMA support when RAM started above
the 4GB boundary which has since been fixed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Upon reception of a new frame, the emac driver checks for a number
of error conditions, and flag the packet as "bad" if any of these
are present. It then allocates a skb unconditionally, but only uses
it if the packet is "good". On the error path, the skb is just forgotten,
and the system leaks memory.

The piece of junk I have on my desk seems to encounter such error
frequently enough so that the box goes OOM after a couple of days,
which makes me grumpy.

Fix this by moving the allocation on the "good_packet" path (and
convert it to netdev_alloc_skb while we're at it).

Tested on a random Allwinner A20 board.

Cc: Stefan Roese <sr@denx.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: <stable@vger.kernel.org> # 3.11+
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dave reported following splat, caused by improper use of
IP_INC_STATS_BH() in process context.

BUG: using __this_cpu_add() in preemptible [00000000] code: trinity-c117/14551
caller is __this_cpu_preempt_check+0x13/0x20
CPU: 3 PID: 14551 Comm: trinity-c117 Not tainted 3.16.0+ #33
 ffffffff9ec898f0 0000000047ea7e23 ffff88022d32f7f0 ffffffff9e7ee207
 0000000000000003 ffff88022d32f818 ffffffff9e397eaa ffff88023ee70b40
 ffff88022d32f970 ffff8801c026d580 ffff88022d32f828 ffffffff9e397ee3
Call Trace:
 [<ffffffff9e7ee207>] dump_stack+0x4e/0x7a
 [<ffffffff9e397eaa>] check_preemption_disabled+0xfa/0x100
 [<ffffffff9e397ee3>] __this_cpu_preempt_check+0x13/0x20
 [<ffffffffc0839872>] sctp_packet_transmit+0x692/0x710 [sctp]
 [<ffffffffc082a7f2>] sctp_outq_flush+0x2a2/0xc30 [sctp]
 [<ffffffff9e0d985c>] ? mark_held_locks+0x7c/0xb0
 [<ffffffff9e7f8c6d>] ? _raw_spin_unlock_irqrestore+0x5d/0x80
 [<ffffffffc082b99a>] sctp_outq_uncork+0x1a/0x20 [sctp]
 [<ffffffffc081e112>] sctp_cmd_interpreter.isra.23+0x1142/0x13f0 [sctp]
 [<ffffffffc081c86b>] sctp_do_sm+0xdb/0x330 [sctp]
 [<ffffffff9e0b8f1b>] ? preempt_count_sub+0xab/0x100
 [<ffffffffc083b350>] ? sctp_cname+0x70/0x70 [sctp]
 [<ffffffffc08389ca>] sctp_primitive_ASSOCIATE+0x3a/0x50 [sctp]
 [<ffffffffc083358f>] sctp_sendmsg+0x88f/0xe30 [sctp]
 [<ffffffff9e0d673a>] ? lock_release_holdtime.part.28+0x9a/0x160
 [<ffffffff9e0d62ce>] ? put_lock_stats.isra.27+0xe/0x30
 [<ffffffff9e73b624>] inet_sendmsg+0x104/0x220
 [<ffffffff9e73b525>] ? inet_sendmsg+0x5/0x220
 [<ffffffff9e68ac4e>] sock_sendmsg+0x9e/0xe0
 [<ffffffff9e1c0c09>] ? might_fault+0xb9/0xc0
 [<ffffffff9e1c0bae>] ? might_fault+0x5e/0xc0
 [<ffffffff9e68b234>] SYSC_sendto+0x124/0x1c0
 [<ffffffff9e0136b0>] ? syscall_trace_enter+0x250/0x330
 [<ffffffff9e68c3ce>] SyS_sendto+0xe/0x10
 [<ffffffff9e7f9be4>] tracesys+0xdd/0xe2

This is a followup of commits f1d8cba6 ("inet: fix possible
seqlock deadlocks") and 7f88c6b2 ("ipv6: fix possible seqlock
deadlock in ip6_finish_output2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reported-by: Dave Jones <davej@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit a71e3c37 ("net: phy: Set the driver when registering an MDIO bus
device") caused the following regression on the fec driver:

root@imx6qsabresd:~# echo mem > /sys/power/state
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.003 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.002 seconds) done.
Unable to handle kernel NULL pointer dereference at virtual address 0000002c
pgd = bcd14000
[0000002c] *pgd=4d9e0831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 617 Comm: sh Not tainted 3.16.0 #17
task: bc0c4e00 ti: bceb6000 task.ti: bceb6000
PC is at fec_suspend+0x10/0x70
LR is at dpm_run_callback.isra.7+0x34/0x6c
pc : [<803f8a98>]    lr : [<80361f44>]    psr: 600f0013
sp : bceb7d70  ip : bceb7d88  fp : bceb7d84
r10: 8091523c  r9 : 00000000  r8 : bd88f478
r7 : 803f8a88  r6 : 81165988  r5 : 00000000  r4 : 00000000
r3 : 00000000  r2 : 00000000  r1 : bd88f478  r0 : bd88f478
Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment user
Control: 10c5387d  Table: 4cd1404a  DAC: 00000015
Process sh (pid: 617, stack limit = 0xbceb6240)
Stack: (0xbceb7d70 to 0xbceb8000)
....

The problem with the original commit is explained by Russell King:

"It has the effect (as can be seen from the oops) of attaching the MDIO bus
device (itself is a bus-less device) to the platform driver, which means
that if the platform driver supports power management, it will be called
to power manage the MDIO bus device.

Moreover, drivers do not expect to be called for power management
operations for devices which they haven't probed, and certainly not for
devices which aren't part of the same bus that the driver is registered
against."

This reverts commit a71e3c37.

Cc: <stable@vger.kernel.org> #3.16
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Need to turn off  SGE RX/TX Callback Timers & interrupt in cxgb4vf PCI Shutdown
routine in order to prevent crashes during reboot/poweroff when traffic is
running.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Antonio Quartulli says:

====================
pull request: batman-adv 2014-08-05

this is a pull request intended for net-next/linux-3.17 (yeah..it's really
late).

Patches 1, 2 and 4 are really minor changes:
- kmalloc_array is substituted to kmalloc when possible (as suggested by
  checkpatch);
- net_ratelimited() is now used properly and the "suppressed" message is not
  printed anymore if not needed;
- the internal version number has been increased to reflect our current version.

Patch 3 instead is introducing a change in the metric computation function
by changing the penalty applied at each mesh hop from 15/255 (~6%) to
30/255 (~11%). This change is introduced by Simon Wunderlich after having
observed a performance improvement in several networks when using the new value.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The variable "err" is not necessary.
Return register_netdevice() directly.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now bridge ports can be non-promiscuous, vlan_vid_add() is no longer an
unnecessary operation.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull media updates from Mauro Carvalho Chehab:
 - removal of sn9c102.  This device driver was replaced a long time ago
   by gspca
 - solo6x10 and go7007 webcam drivers moved from staging into
   mainstream.  They were waiting for an API to allow setting the image
   detection matrix
 - SDR drivers moved from staging into mainstream: sdr-msi3101 (renamed
   as msi2500) and rtl2832
 - added SDR driver for airspy
 - added demux driver: si2165
 - rework at several RC subsystem, making the code for RC-5 SZ variant
   to be added at the standard RC5 decoder
 - added decoder for the XMP IR protocol
 - tuner driver moved from staging into mainstream: msi3101 (renamed as
   msi001)
 - added documentation for some additional SDR pixfmt
 - some device tree bindings documented
 - added support for exynos3250 at s5p-jpeg
 - remove the obsolete, unmaintained and broken mx1_camera driver
 - added support for remote controllers at au0828 driver
 - added a RC driver: sunxi-cir
 - several driver fixes, enhancements and cleanups.

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (455 commits)
  [media] cx23885: fix UNSET/TUNER_ABSENT confusion
  [media] coda: fix build error by making reset control optional
  [media] radio-miropcm20: fix sparse NULL pointer warning
  [media] MAINTAINERS: Update go7007 pattern
  [media] MAINTAINERS: Update solo6x10 patterns
  [media] media: atmel-isi: add primary DT support
  [media] media: atmel-isi: convert the pdata from pointer to structure
  [media] media: atmel-isi: add v4l2 async probe support
  [media] rcar_vin: add devicetree support
  [media] media: pxa_camera device-tree support
  [media] media: mt9m111: add device-tree suppport
  [media] soc_camera: add support for dt binding soc_camera drivers
  [media] media: soc_camera: pxa_camera documentation device-tree support
  [media] media: mt9m111: add device-tree documentation
  [media] s5p-mfc: remove unnecessary calling to function video_devdata()
  [media] s5p-jpeg: add chroma subsampling adjustment for Exynos3250
  [media] s5p-jpeg: Prevent erroneous downscaling for Exynos3250 SoC
  [media] s5p-jpeg: Assure proper crop rectangle initialization
  [media] s5p-jpeg: fix g_selection op
  [media] s5p-jpeg: Adjust jpeg_bound_align_image to Exynos3250 needs
  ...

Willem de Bruijn says:

====================
net-timestamp: new tx tstamps and tcp

Extend socket tx timestamping:
- allow multiple types of software timestamps aside from send (1)
- add software timestamp on enter packet scheduling (4)
- add software timestamp for TCP (5)
- add software timestamp for TCP on ACK (6)

The sk_flags option space is nearly exhausted. Also move the
many timestamp options to a new sk->sk_tstamps (2).

To disambiguate data when tstamps may arrive out of order,
optionally return a sequential ID assigned at send (3).

Extend Linux tx timestamping to monitoring of latency
incurred within the kernel stack and to protocols embedded in TCP.
Complex kernel setups may have multiple layers of queueing, including
multiple instances of packet scheduling, and many classes per layer.
Many applications embed discrete payloads into TCP bytestreams for
reliability, flow control, etcetera. Detecting application tail
latency in such scenarios relies on identifying the exact queue
responsible if on the host, or the network latency if otherwise.

Changelog:
v4->v5
  - define SCM_TSTAMP_SND == 0, for legacy behavior
  - add TCP tstamps without changing the generated byte stream
    - modify GSO and ACK to find offset: slightly more complex
      than previous invariant that it is the last byte
  - consistent naming of packet scheduling
    - rename SCM_TSTAMP_ENQ to SCM_TSTAMP_SCHED
  - add unique key in ee_data
  - add id field in ee_info to disambiguate tstamps
    - optional, only on new flag SOF_TIMESTAMPING_OPT_ID
    - for bytestream, in bytes

v3->v4
  - (v3 review comment) removed skb->mark packet identification (*A)
  - (v3 review comment) fixed indentation
  - tcp: fixed poll() to return POLLERR on non-zero queue
  - rebased to work without syststamp
  - comments: removed all traces of MSG_TSTAMP_.. (*B)

v2->v3
  - extend the SO_TIMESTAMPING API, instead of defining a new one.
  - add protocol independent support to correlate tstamps with data,
    based on returning skb->mark.
  - removed no-payload optimization and documentation (for now):

    I have a follow-on patch that reintroduces MSG_TSTAMP along with a
    new socket option SOF_TIMESTAMPING_OPT_ONFLAG. This is equivalent
    to sequence setsockopt(<enable>); send(..); setsockopt(<disable>),
    but avoids the need to define a MSG_TSTAMP_<TYPE> for each type.

    I will leave these three patches as follow-on, as this patchset is
    large enough as is.

v1->v2
  - expand timestamping (existing and new) to SOCK_RAW and ping sockets
  - rename sock_errqueue_timestamping to scm_timestamping
  - change timestamp data format: do not add fields to scm_timestamping.
      Doing so could break legacy applications. Instead, communicate
      through an existing, but unused, field in the error message.
  - rename SOF_.._OPT_TX_NO_PAYLOAD to shorter SOF_.._OPT_TSONLY
  - move msg_tstamp test app out of patchset and to github
      git://github.com/wdebruij/kerneltools.git
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add SOF_TIMESTAMPING_TX_ACK, a request for a tstamp when the last byte
in the send() call is acknowledged. It implements the feature for TCP.

The timestamp is generated when the TCP socket cumulative ACK is moved
beyond the tracked seqno for the first time. The feature ignores SACK
and FACK, because those acknowledge the specific byte, but not
necessarily the entire contents of the buffer up to that byte.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TCP timestamping extends SO_TIMESTAMPING to bytestreams.

Bytestreams do not have a 1:1 relationship between send() buffers and
network packets. The feature interprets a send call on a bytestream as
a request for a timestamp for the last byte in that send() buffer.

The choice corresponds to a request for a timestamp when all bytes in
the buffer have been sent. That assumption depends on in-order kernel
transmission. This is the common case. That said, it is possible to
construct a traffic shaping tree that would result in reordering.
The guarantee is strong, then, but not ironclad.

This implementation supports send and sendpages (splice). GSO replaces
one large packet with multiple smaller packets. This patch also copies
the option into the correct smaller packet.

This patch does not yet support timestamping on data in an initial TCP
Fast Open SYN, because that takes a very different data path.

If ID generation in ee_data is enabled, bytestream timestamps return a
byte offset, instead of the packet counter for datagrams.

The implementation supports a single timestamp per packet. It silenty
replaces requests for previous timestamps. To avoid missing tstamps,
flush the tcp queue by disabling Nagle, cork and autocork. Missing
tstamps can be detected by offset when the ee_data ID is enabled.

Implementation details:

- On GSO, the timestamping code can be included in the main loop. I
moved it into its own loop to reduce the impact on the common case
to a single branch.

- To avoid leaking the absolute seqno to userspace, the offset
returned in ee_data must always be relative. It is an offset between
an skb and sk field. The first is always set (also for GSO & ACK).
The second must also never be uninitialized. Only allow the ID
option on sockets in the ESTABLISHED state, for which the seqno
is available. Never reset it to zero (instead, move it to the
current seqno when reenabling the option).
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kernel transmit latency is often incurred in the packet scheduler.
Introduce a new timestamp on transmission just before entering the
scheduler. When data travels through multiple devices (bonding,
tunneling, ...) each device will export an individual timestamp.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Datagrams timestamped on transmission can coexist in the kernel stack
and be reordered in packet scheduling. When reading looped datagrams
from the socket error queue it is not always possible to unique
correlate looped data with original send() call (for application
level retransmits). Even if possible, it may be expensive and complex,
requiring packet inspection.

Introduce a data-independent ID mechanism to associate timestamps with
send calls. Pass an ID alongside the timestamp in field ee_data of
sock_extended_err.

The ID is a simple 32 bit unsigned int that is associated with the
socket and incremented on each send() call for which software tx
timestamp generation is enabled.

The feature is enabled only if SOF_TIMESTAMPING_OPT_ID is set, to
avoid changing ee_data for existing applications that expect it 0.
The counter is reset each time the flag is reenabled. Reenabling
does not change the ID of already submitted data. It is possible
to receive out of order IDs if the timestamp stream is not quiesced
first.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sk_flags is reaching its limit. New timestamping options will not fit.
Move all of them into a new field sk->sk_tsflags.

Added benefit is that this removes boilerplate code to convert between
SOF_TIMESTAMPING_.. and SOCK_TIMESTAMPING_.. in getsockopt/setsockopt.

SOCK_TIMESTAMPING_RX_SOFTWARE is also used to toggle the receive
timestamp logic (netstamp_needed). That can be simplified and this
last key removed, but will leave that for a separate patch.
Signed-off-by: Willem de Bruijn <willemb@google.com>

----

The u16 in sock can be moved into a 16-bit hole below sk_gso_max_segs,
though that scatters tstamp fields throughout the struct.
Signed-off-by: David S. Miller <davem@davemloft.net>

Applications that request kernel tx timestamps with SO_TIMESTAMPING
read timestamps as recvmsg() ancillary data. The response is defined
implicitly as timespec[3].

1) define struct scm_timestamping explicitly and

2) add support for new tstamp types. On tx, scm_timestamping always
   accompanies a sock_extended_err. Define previously unused field
   ee_info to signal the type of ts[0]. Introduce SCM_TSTAMP_SND to
   define the existing behavior.

The reception path is not modified. On rx, no struct similar to
sock_extended_err is passed along with SCM_TIMESTAMPING.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These belong to the t4 msg header, will ensure there is no accidental code
duplication in the future
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit reduces spurious retransmits due to apparent SACK reneging
by only reacting to SACK reneging that persists for a short delay.

When a sequence space hole at snd_una is filled, some TCP receivers
send a series of ACKs as they apparently scan their out-of-order queue
and cumulatively ACK all the packets that have now been consecutiveyly
received. This is essentially misbehavior B in "Misbehaviors in TCP
SACK generation" ACM SIGCOMM Computer Communication Review, April
2011, so we suspect that this is from several common OSes (Windows
2000, Windows Server 2003, Windows XP). However, this issue has also
been seen in other cases, e.g. the netdev thread "TCP being hoodwinked
into spurious retransmissions by lack of timestamps?" from March 2014,
where the receiver was thought to be a BSD box.

Since snd_una would temporarily be adjacent to a previously SACKed
range in these scenarios, this receiver behavior triggered the Linux
SACK reneging code path in the sender. This led the sender to clear
the SACK scoreboard, enter CA_Loss, and spuriously retransmit
(potentially) every packet from the entire write queue at line rate
just a few milliseconds before the ACK for each packet arrives at the
sender.

To avoid such situations, now when a sender sees apparent reneging it
does not yet retransmit, but rather adjusts the RTO timer to give the
receiver a little time (max(RTT/2, 10ms)) to send us some more ACKs
that will restore sanity to the SACK scoreboard. If the reneging
persists until this RTO then, as before, we clear the SACK scoreboard
and enter CA_Loss.

A 10ms delay tolerates a receiver sending such a stream of ACKs at
56Kbit/sec. And to allow for receivers with slower or more congested
paths, we wait for at least RTT/2.

We validated the resulting max(RTT/2, 10ms) delay formula with a mix
of North American and South American Google web server traffic, and
found that for ACKs displaying transient reneging:

 (1) 90% of inter-ACK delays were less than 10ms
 (2) 99% of inter-ACK delays were less than RTT/2

In tests on Google web servers this commit reduced reneging events by
75%-90% (as measured by the TcpExtTCPSACKReneging counter), without
any measurable impact on latency for user HTTP and SPDY requests.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rajesh Borundia says:

====================
qlcnic: Bug fixes

The patch series contains following bug fixes.

* Aggregating tx stats in adapter variable was resulting
  in increase of stats when user runs ifconfig command
  and no traffic is running. Instead aggregate tx stats
  in local variable and then assign it to adapter struct
  variable.
* Set_driver_version was called after registering netdev
  which was resulting in a race between FLR in open
  handler and set_driver_version command as open handler
  can be called simulatneously on another cpu even if probe
  is not complete. So call this command before registering
  netdev.
* dcbnl_ops should be initialized before registering netdev
  as they are referenced in open handler.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>