Skip to content

L
linux
Switch branch/tag
  1. 21 Sep, 2010 16 commits
  3. 17 Sep, 2010 10 commits
  5. 16 Sep, 2010 14 commits
    • Luis R. Rodriguez's avatar
      ath9k: fix regression which disabled ps on ath9k · 008443de
      Luis R. Rodriguez authored 
      The patch titled "ath9k: Add new file init.c" shuffled some code
around but in dong so for some reason also removed the revision
check for disablign power save. Add this revision check again
so we can get power save re-enabled again by default on cards
newer than AR5416 and AR5418.

$ git describe --contains 55624204
v2.6.34-rc1~233^2~49^2~343

This patch has fixes for stable kernels [2.6.34+].

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: default avatarLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
      008443de
    • Senthil Balasubramanian's avatar
      ath9k: fix regression which prevents chip sleep after CAB data · 3fac6dfd
      Senthil Balasubramanian authored 
      The patch:

commit 293dc5df
Author: Gabor Juhos <juhosg@openwrt.org>
Date:   Fri Jun 19 12:17:48 2009 +0200

    ath9k: remove ath_rx_ps_back_to_sleep helper

    This helper only clears the SC_OP_WAIT_FOR_{BEACON,CAB} flags.
    Remove it and clear these flags directly in the approptiate
    places instead.

    Changes-licensed-under: ISC
Signed-off-by: default avatarGabor Juhos <juhosg@openwrt.org>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>

introduced a regression which forgot to lift the beacon flag
after we received all broadcast and multicast data. This meant
we never went to sleep consuming about ~650mW on idle. This pretty
much broke power save completely.

This patch has fixes for stable kernels [2.6.32+].

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Sameer Nanda <snanda@google.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: default avatarSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: default avatarLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
      3fac6dfd
    • Luis R. Rodriguez's avatar
      mac80211: send last 3/5 probe requests as unicast · f01a067d
      Luis R. Rodriguez authored 
      Some buggy APs do not respond to unicast probe requests
or send unicast probe requests very delayed so in the
worst case we should try to send broadcast probe requests,
otherwise we can get disconnected from these APs.

Even if drivers do not have filters to disregard probe
responses from foreign APs mac80211 will only process
probe responses from our associated AP for re-arming
connection monitoring.

We need to do this since the beacon monitor does not
push back the connection monitor by design so even if we
are getting beacons from these type of APs our connection
monitor currently relies heavily on the way the probe
requests are received on the AP. An example of an AP
affected by this is the Nexus One, but this has also been
observed with random APs.

We can probably optimize this later by using null funcs
instead of probe requests.

For more details refer to:

http://code.google.com/p/chromium-os/issues/detail?id=5715

This patch has fixes for stable kernels [2.6.35+].

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: default avatarLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
      f01a067d
    • Luis R. Rodriguez's avatar
      mac80211: disable beacon monitor while going offchannel · 3bc3c0d7
      Luis R. Rodriguez authored 
      The beacon monitor should be disabled when going off channel
to prevent spurious warnings and triggering connection
deterioration work such as sending probe requests. Re-enable
the beacon monitor once we come back to the home channel.

This patch has fixes for stable kernels [2.6.34+].

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: default avatarLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
      3bc3c0d7
    • Luis R. Rodriguez's avatar
      mac80211: make the beacon monitor available externally · d3a910a8
      Luis R. Rodriguez authored 
      This will be used by other components next. The beacon
monitor was added as of 2.6.34 so these fixes are applicable
only to kernels >= 2.6.34.

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: default avatarLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
      d3a910a8
    • Luis R. Rodriguez's avatar
      mac80211: reset connection idle when going offchannel · 4730d597
      Luis R. Rodriguez authored 
      When we go offchannel mac80211 currently leaves alive the
connection idle monitor. This should be instead postponed
until we come back to our home channel, otherwise by the
time we get back to the home channel we could be triggering
unecesary probe requests. For APs that do not respond to
unicast probe requests (Nexus One is a simple example) this
means we essentially get disconnected after the probes
fails.

This patch has stable fixes for kernels [2.6.35+]

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: default avatarLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
      4730d597
    • Luis R. Rodriguez's avatar
      mac80211: reset probe send counter upon connection timer reset · 0c699c3a
      Luis R. Rodriguez authored 
      Upon beacon loss we send probe requests after 30 seconds of idle
time and we wait for each probe response 1/2 second. We send a
total of 3 probe requests before giving up on the AP. In the case
that we reset the connection idle monitor we should reset the probe
requests count to 0. Right now this won't help in any way but
the next patch will.

This patch has fixes for stable kernel [2.6.35+].

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: default avatarLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
      0c699c3a
    • Luis R. Rodriguez's avatar
      mac80211: add helper for reseting the connection monitor · be099e82
      Luis R. Rodriguez authored 
      This will be used in another place later. The connection
monitor was added as of 2.6.35 so these fixes will be
applicable to >= 2.6.35.

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: default avatarLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
      be099e82
    • Luis R. Rodriguez's avatar
      ath9k: fix enabling ANI / tx monitor after bg scan · 48a6a468
      Luis R. Rodriguez authored 
      ath9k's entire logic with SC_OP_SCANNING is incorrect due to the
way mac80211 currently implements the scan complete callback and
we handle it in ath9k. This patch removes the flag completely in
preference for the SC_OP_OFFCHANNEL which is really what we wanted.

The scanning flag was used to ensure we reset ANI to the old values
when we go back to the home channel, but if we are offchannel we
use some defaults. The flag was also used to re-enable the TX monitor.

Without this patch we simply never re-enabled ANI and the TX monitor
after going offchannel. This means that after one background
scan we are prone to noise issues and if we had a TX hang we would
not recover. To get this to work properly we must enable ANI after
we have configured the beacon timers, otherwise hardware acts really
oddly.

This patch has stable fixes which apply down to [2.6.36+], there
*may* be a to fix this on older kernels but requires a bit of
work since this patch relies on the new mac80211 flag
IEEE80211_CONF_OFFCHANNEL which was introduced as of 2.6.36.

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: default avatarLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
      48a6a468
    • Luis R. Rodriguez's avatar
      ath9k: fix regression on beacon loss after bgscan · 52b8ac92
      Luis R. Rodriguez authored 
      When we return to the home channel we were never reseting our beacon
timers, this was casued by the fact that the scanning flag was still
on even after we returned to our home channel. There are also other
reasons why we would get a reset and if we are not off channel
we always need to resynch our beacon timers, because a reset will
clear them.

This bug is a regression introduced on 2.6.36. The order of the
changes are as follows:

5ee08656 - Sat Jul 31 - ath9k: prevent calibration during off-channel activity
a0daa0e7 - Tue Jul 27 - Revert "mac80211: fix sw scan bracketing"
543708be - Fri Jun 18 - mac80211: fix sw scan bracketing

mcgrof@tux ~/linux-2.6-allstable (git::master)$ git describe \
        --contains 5ee08656
v2.6.36-rc1~43^2~34^2~22

mcgrof@tux ~/linux-2.6-allstable (git::master)$ git describe \
        --contains a0daa0e7
v2.6.36-rc1~571^2~64^2~13

mcgrof@tux ~/linux-2.6-allstable (git::master)$ git describe \
        --contains 543708be
v2.6.36-rc1~571^2~107^2~187

So 5ee08656 would have worked if a0daa0e7 was not committed but
it was so this means 5ee08656 was broken since it assumed that
when we were in the channel change routine the scan flag would
be lifted. As it turns out the scan flag will be set when we
are already on the home channel.

For more details refer to:

http://code.google.com/p/chromium-os/issues/detail?id=5715

These issues will need to be considered for our solution on
reshifting the scan complete callback location on mac80211 on
current development kernel work.

This patch has stable fixes which apply down to [2.6.36+]

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: default avatarLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
      52b8ac92
    • Luis R. Rodriguez's avatar
      ath9k: fix power save race conditions · 8ab2cd09
      Luis R. Rodriguez authored 
      ath9k has a race on putting the chip into network sleep and
having registers read from hardware. The race occurs because
although ath9k_ps_restore() locks its own callers it makes use
of some variables which get altered in the driver at different
code paths. The variables are the ps_enabled and ps_flags.

This is easily reprodicible in large network environments when
roaming with the wpa_supplicant simple bgscan. You'd get some
0xdeadbeef read out on certain registers such as:

ath: timeout (100000 us) on reg 0x806c: 0xdeadbeef & 0x01f00000 != 0x00000000
ath: RX failed to go idle in 10 ms RXSM=0xdeadbeef

ath: timeout (100000 us) on reg 0x7000: 0xdeadbeef & 0x00000003 != 0x00000000
ath: Chip reset failed

The fix is to protect the ath9k_config(hw, IEEE80211_CONF_CHANGE_PS)
calls with a spin_lock_irqsave() which will disable contendors for
these variables from interrupt context, timers, re-entry from mac80211
on the same callback, and most importantly from ath9k_ps_restore()
which is the only call which will put the device into network sleep.

There are quite a few threads and bug reports on these a few of them are:

https://bugs.launchpad.net/ubuntu/karmic/+source/linux/+bug/407040
http://code.google.com/p/chromium-os/issues/detail?id=5709
http://code.google.com/p/chromium-os/issues/detail?id=5943

Stable fixes apply to [2.6.32+]

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: default avatarLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
      8ab2cd09
    • Rajkumar Manoharan's avatar
      ath9k_htc: Fix register read through bulk pipe · 0f529e98
      Rajkumar Manoharan authored 
      To optimize register read/write operations, the HTC firmwares were patched
to change EP3 and EP4 pipe types from Interrupt to Bulk. So register writes
are submitted as bulk urbs, but register reads are not. Also changing the
register read endpoint pipe as bulk type when URBs are filled improves the
register reads considerably which results in reduced scan time and CPU
utilization.
Signed-off-by: default avatarRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
      0f529e98
    • Johannes Berg's avatar
      mac80211: add p2p device type support · 2ca27bcf
      Johannes Berg authored 
      When a driver advertises p2p device support,
mac80211 will handle it, but internally it will
rewrite the interface type to STA/AP rather than
P2P-STA/GO since otherwise a lot of paths need
to be touched that are otherwise identical. A
p2p boolean tells drivers whether or not a given
interface will be used for p2p or not.
Signed-off-by: default avatarJohannes Berg <johannes.berg@intel.com>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
      2ca27bcf
    • Johannes Berg's avatar
      cfg80211/nl80211: introduce p2p device types · 074ac8df
      Johannes Berg authored 
      This adds P2P-STA and P2P-GO as device types so
we can distinguish between those and normal STA
or AP (respectively) type interfaces.
Signed-off-by: default avatarJohannes Berg <johannes.berg@intel.com>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
      074ac8df
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7