bcm_sf2 only appears to support pause modes on RGMII interfaces (the
enable bits are in the RGMII control register.)  Setup the pause modes
for RGMII connections.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert the bcm_sf2 to use the finalised speed and duplex in its
mac_link_up() call rather than the parameters in mac_config().
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

state->link has never been valid in mac_config() implementations -
while it may be correct in some calls, it is not true that it can be
relied upon.

Fix bcm_sf2 to use the correct method of handling forced link status.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Russell King says:

====================
Convert Broadcom B53 to mac_link_up() resolved state

These two patches update the Broadcom B53 DSA support to use the newly
provided resolved link state via mac_link_up() rather than using the
state in mac_config().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert the B53 driver to use the finalised link parameters in
mac_link_up() rather than the parameters in mac_config(). This is
just a matter of moving the call to b53_force_port_config().
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace the b53_force_port_config() pause argument, which is based on
phylink's MLO_PAUSE_* definitions, to use a pair of booleans.  This
will allow us to move b53_force_port_config() from
b53_phylink_mac_config() to b53_phylink_mac_link_up().
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
This feature/cleanup patchset includes the following patches:

 - bump version strings, by Simon Wunderlich

 - update mailing list URL, by Sven Eckelmann

 - fix typos and grammar in documentation, by Sven Eckelmann

 - introduce a configurable per interface hop penalty,
   by Linus Luessing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

It is not very informative to know the DSA master device when a
subordinate network device fails to get its PHY setup. Provide the
device name and capitalize PHY while we are it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

remove unused but set variable to avoid auto build test WARNING
Signed-off-by: Luo bin <luobin9@huawei.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
1GbE Intel Wired LAN Driver Updates 2020-06-29

This series contains updates to only the igc driver.

Sasha added Energy Efficient Ethernet (EEE) support and Latency Tolerance
Reporting (LTR) support for the igc driver. Added Low Power Idle (LPI)
counters and cleaned up unused TCP segmentation counters. Removed
igc_power_down_link() and call igc_power_down_phy_copper_base()
directly. Removed unneeded copper media check.

Andre cleaned up timestamping by removing un-supported features and
duplicate code for i225. Fixed the timestamp check on the proper flag
instead of the skb for pending transmit timestamps. Refactored
igc_ptp_set_timestamp_mode() to simply the flow.

v2: Removed the log message in patch 1 as suggested by David Miller.
    Note: The locking issue Jakub Kicinski saw in patch 5, currently
    exists in the current net-next tree, so Andre will resolve the
    locking issue in a follow-on patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

i225 device support only copper mode.
There is no point to check media type in the
igc_config_fc_after_link_up() method.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

PHY of the i225 device support only copper mode.
There is no point to check media type in the
igc_power_up_link() method.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently the implementation of igc_power_down_link()
method was just calling igc_power_down_phy_copper_base()
method.
We can just call igc_power_down_phy_copper_base()
method directly.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

TCP segmentation TX context fail counter is not
applicable for i225 devices.
This patch comes to clean up this counter.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown<aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add EEE TX LPI and EEE RX LPI counters. A EEE TX LPI event
occurs when the transmitter enters EEE (IEEE 802.3az) LPI
state. A EEE RX LPI event occurs when the receiver detect
link partner entry into EEE(IEEE 802.3az) LPI state.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When Rx timestamping is enabled, we set the timestamp bit in SRRCTL
register for each queue, but we don't clear it when disabling. This
patch fixes igc_ptp_disable_rx_timestamp() accordingly.

Also, this patch gets rid of igc_ptp_enable_tstamp_rxqueue() and
igc_ptp_enable_tstamp_all_rxqueues() and move their logic into
igc_ptp_enable_rx_timestamp() to keep the enable and disable
helpers symmetric.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Current igc_ptp_set_timestamp_mode() logic is a bit tangled since it
handles many different hardware configurations in one single place,
making it harder to follow. This patch untangles that code by breaking
it into helper functions.

Quick note about the hw->mac.type check which was removed in this
refactoring: this check it not really needed since igc_i225 is the only
type supported by the IGC driver.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

As implemented in igc_ethtool_get_ts_info(), igc only supports HWTSTAMP_
FILTER_ALL so any HWTSTAMP_FILTER_* option the user may set falls back to
HWTSTAMP_FILTER_ALL.

HWTSTAMP_FILTER_ALL is implemented via Rx Time Sync Control (TSYNCRXCTL)
configuration which timestamps all incoming packets. Configuring a
UDP filter, in addition to TSYNCRXCTL, doesn't add much so this patch
removes that code. It also takes this opportunity to remove some
non-applicable comments.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The __IGC_PTP_TX_IN_PROGRESS flag indicates we have a pending Tx
timestamp. In some places, instead of checking that flag, we check
adapter->ptp_tx_skb. This patch fixes those places to use the flag.

Quick note about igc_ptp_tx_hwtstamp() change: when that function is
called, adapter->ptp_tx_skb is expected to be valid always so we
WARN_ON_ONCE() in case it is not.

Quick note about igc_ptp_suspend() change: when suspending, we don't
really need to check if there is a pending timestamp. We can simply
clear it unconditionally.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The functions igc_ptp_tx_hang() and igc_ptp_tx_work() have duplicate
code which handles Tx timestamp timeouts. This patch does a trivial
refactoring by moving that code to its own function and reusing it.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Differently from I210, I225 doesn't report Rx timestamps via the TS bit
Rx descriptor + RXSTMPL/RXSTMPH registers mechanism. Rx timestamps are
reported in the packet buffer only, which is implemented by igc_ptp_rx_
pktstamp(). So this patch removes igc_ptp_rx_rgtstamp() and all code
related to it, copied from igb driver.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The LTR message on the PCIe inform the requested latency
on which the PCIe must become active to the downstream
PCIe port of the system.
This patch provide recommended LTR parameters by i225
specification.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Ido Schimmel says:

====================
Add ethtool extended link state

Amit says:

Currently, device drivers can only indicate to user space if the network
link is up or down, without additional information.

This patch set provides an infrastructure that allows these drivers to
expose more information to user space about the link state. The
information can save users' time when trying to understand why a link is
not operationally up, for example.

The above is achieved by extending the existing ethtool LINKSTATE_GET
command with attributes that carry the extended state.

For example, no link due to missing cable:

$ ethtool ethX
...
Link detected: no (No cable)

Beside the general extended state, drivers can pass additional
information about the link state using the sub-state field. For example:

$ ethtool ethX
...
Link detected: no (Autoneg, No partner detected)

In the future the infrastructure can be extended - for example - to
allow PHY drivers to report whether a downshift to a lower speed
occurred. Something like:

$ ethtool ethX
...
Link detected: yes (downshifted)

Patch set overview:

Patches #1-#3 move mlxsw ethtool code to a separate file
Patches #4-#5 add the ethtool infrastructure for extended link state
Patches #6-#7 add support of extended link state in the mlxsw driver
Patches #8-#10 add test cases

Changes since v1:

* In documentation, show ETHTOOL_LINK_EXT_STATE_* and
  ETHTOOL_LINK_EXT_SUBSTATE_* constants instead of user-space strings
* Add `_CI_` to cable_issue substates to be consistent with
  other substates
* Keep the commit messages within 75 columns
* Use u8 variable for __link_ext_substate
* Document the meaning of -ENODATA in get_link_ext_state() callback
  description
* Do not zero data->link_ext_state_provided after getting an error
* Use `ret` variable for error value

Changes since RFC:

* Move documentation patch before ethtool patch
* Add nla_total_size() instead of sizeof() directly
* Return an error code from linkstate_get_ext_state()
* Remove SHORTED_CABLE, add CABLE_TEST_FAILURE instead
* Check if the interface is administratively up before setting ext_state
* Document all sub-states
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add tests to check ethtool report about extended state.
The tests configure several states and verify that the correct extended
state is reported by ethtool.

Check extended state with substate (Autoneg) and extended state without
substate (No cable).
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add NETIF_NO_CABLE port to tests topology.

The port can also be declared as an environment variable and tests can be
run like that:
NETIF_NO_CABLE=eth9 ./test.sh eth{1..8}

The NETIF_NO_CABLE port will be used by ethtool_extended_state test.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently different_speeds_get() is used only by ethtool.sh tests.
The function can be useful for another tests that check ethtool
configurations.

Move the function to ethtool_lib in order to allow other tests to use
it.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement .get_down_ext_state() as part of ethtool_ops.
Query link down reason from PDDR register and convert it to ethtool
link_ext_state.

In case that more information than common link_ext_state is provided,
fill link_ext_substate also with the appropriate value.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PDDR register enables to read the Phy debug database.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, drivers can only tell whether the link is up/down using
LINKSTATE_GET, but no additional information is given.

Add attributes to LINKSTATE_GET command in order to allow drivers
to expose the user more information in addition to link state to ease
the debug process, for example, reason for link down state.

Extended state consists of two attributes - link_ext_state and
link_ext_substate. The idea is to avoid 'vendor specific' states in order
to prevent drivers to use specific link_ext_state that can be in the future
common link_ext_state.

The substates allows drivers to add more information to the common
link_ext_state. For example, vendor can expose 'Autoneg' as link_ext_state
and add 'No partner detected during force mode' as link_ext_substate.

If a driver cannot pinpoint the extended state with the substate
accuracy, it is free to expose only the extended state and omit the
substate attribute.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add link extended state attributes.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move mlxsw_sp1_port_type_speed_ops and mlxsw_sp2_port_type_speed_ops
with the relevant code from spectrum.c to spectrum_ethtool.c.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add spectrum_ethtool.c file for ethtool code.
Move ethtool_ops and the relevant code from spectrum.c to
spectrum_ethtool.c.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw_sp_port_headroom_set() is defined twice - in spectrum.c and in
spectrum_dcb.c, with different arguments and different implementation
but the name is same.

Rename mlxsw_sp_port_headroom_set() to mlxsw_sp_port_headroom_ets_set()
in order to allow using the second function in several files, and not
only as static function in spectrum.c.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IEEE802.3az-2010 Energy Efficient Ethernet has been
approved as standard (September 2010) and the driver
can enable and disable it via ethtool.
Disable the feature by default on parts which support it.
Add enable/disable eee options.
tx-lpi, tx-timer and advertise not supported yet.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Ioana Ciornei says:

====================
dpaa2-eth: send a scatter-gather FD instead of realloc-ing

This patch set changes the behaviour in case the Tx path is confroted
with an SKB with insufficient headroom for our hardware necessities (SW
annotation area). In the first patch, instead of realloc-ing the SKB we
now send a S/G frames descriptor while the second one adds a new
software held counter to account for for these types of frames.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

With the previous commit, in case of insufficient SKB headroom on the Tx
path instead of reallocing the SKB we now send a S/G frame descriptor.
Export the number of occurences of this case as a per CPU counter (in
debugfs) and a total number in the ethtool statistics - "tx converted sg
frames'.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of realloc-ing the skb on the Tx path when the provided headroom
is smaller than the HW requirements, create a Scatter/Gather frame
descriptor with only one entry.

Remove the '[drv] tx realloc frames' counter exposed previously through
ethtool since it is no longer used.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Edward Cree says:

====================
sfc: prerequisites for EF100 driver, part 1

This continues the work started by Alex Maftei <amaftei@solarflare.com>
 in the series "sfc: code refactoring", "sfc: more code refactoring",
 "sfc: even more code refactoring" and "sfc: refactor mcdi filtering
 code", to prepare for a new driver which will share much of the code
 to support the new EF100 family of Solarflare/Xilinx NICs.
After this series, there will be approximately two more of these
 'prerequisites' series, followed by the sfc_ef100 driver itself.

v2: fix reverse xmas tree in patch 5.  (Left the cases in patches 7,
 9 and 14 alone as those are all in pure movement of existing code.)
====================
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

EF100 will use CHECKSUM_COMPLETE, but will also make use of
 efx_rx_packet_gro(), thus needs to be able to pass the checksum value
 into that function.
Drivers for older NICs pass in a csum of 0 to get the old semantics (use
 the RX flags for CHECKSUM_UNNECESSARY marking).
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

EF100 will use the same approach to ARFS as EF10.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>