- 02 Dec, 2014 1 commit
-
-
Christophe Ricard authored
se_io allows to send apdu over the CLF to the embedded Secure Element. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
- 01 Dec, 2014 4 commits
-
-
Christophe Ricard authored
- phy->gpio_irq is never done out of the request resources. - irq_of_parse_and_map is already done in the i2c core so client->irq is already set when entering in st21nfcb_hci_i2c_of_request_resources - In case of static platform configuration client->irq can be set directly. - It simplifies the code a bit. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Christophe Ricard authored
When CONFIG_OF is define add of_st21nfcb_i2c_match to MODULE_DEVICE_TABLE Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Christophe Ricard authored
- phy->gpio_irq is never done out of the request resources. - irq_of_parse_and_map is already done in the i2c core so client->irq is already set when entering in st21nfca_hci_i2c_of_request_resources - In case of static platform configuration client->irq can be set directly - It simplifies the code a bit. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Christophe Ricard authored
When CONFIG_OF is define add of_st21nfca_i2c_match to MODULE_DEVICE_TABLE. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
- 28 Nov, 2014 24 commits
-
-
Julien Lefrique authored
Before signaling the deactivation, send a deactivation request if in RFST_DISCOVERY state because neard assumes polling is stopped and will try to restart it. Signed-off-by: Julien Lefrique <lefrique@marvell.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Julien Lefrique authored
When the deactivation type reported by RF_DEACTIVATE_NTF is Discovery, go in RFST_DISCOVERY state. The NFCC stays in Poll mode and/or Listen mode. Signed-off-by: Julien Lefrique <lefrique@marvell.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Julien Lefrique authored
Signed-off-by: Julien Lefrique <lefrique@marvell.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Julien Lefrique authored
Signed-off-by: Julien Lefrique <lefrique@marvell.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Julien Lefrique authored
As specified in NCI 1.0 and NCI 1.1, when using the NFC-DEP RF Interface, the DH and the NFCC shall only use the Static RF Connection for data communication with a Remote NFC Endpoint. Signed-off-by: Julien Lefrique <lefrique@marvell.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Julien Lefrique authored
The Target responds to the ATR_REQ with the ATR_RES. Configure the General Bytes in ATR_RES with the first three octets equal to the NFC Forum LLCP magic number, followed by some LLC Parameters TLVs described in section 4.5 of [LLCP]. Signed-off-by: Julien Lefrique <lefrique@marvell.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Julien Lefrique authored
Changes: * Extract the Listen mode activation parameters from RF_INTF_ACTIVATED_NTF. * Store the General Bytes of ATR_REQ. * Signal that Target mode is activated in case of an activation in NFC-DEP. * Update the NCI state accordingly. * Use the various constants defined in nfc.h. * Fix the ATR_REQ and ATR_RES maximum size. As per NCI 1.0 and NCI 1.1, the Activation Parameters for both Poll and Listen mode contain all the bytes of ATR_REQ/ATR_RES starting and including Byte 3 as defined in [DIGITAL]. In [DIGITAL], the maximum size of ATR_REQ/ATR_RES is 64 bytes and they are numbered starting from Byte 1. Signed-off-by: Julien Lefrique <lefrique@marvell.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Julien Lefrique authored
Send LA_SEL_INFO and LF_PROTOCOL_TYPE with NFC-DEP protocol enabled. Configure 212 Kbit/s and 412 Kbit/s bit rates for Listen F. Signed-off-by: Julien Lefrique <lefrique@marvell.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Julien Lefrique authored
The Target mode protocols are given to the nci_start_poll() function but were previously ignored. To enable P2P Target, when NFC-DEP is requested as a Target mode protocol, add NFC-A and NFC-F Passive Listen modes in RF_DISCOVER_CMD command. Signed-off-by: Julien Lefrique <lefrique@marvell.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Axel Lin authored
list_for_each_entry_safe() is necessary if list objects are deleted from the list while traversing it. Not the case here, so we can use the base list_for_each_entry variant. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Johannes Berg authored
This is a specific implementation, <asm/unaligned.h> is the multiplexer that has the arch-specific knowledge of which of the implementations needs to be used, so include that. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Mark A. Greer authored
When an NFC-DEP target receives an ATN PDU, its supposed to respond with a similar ATN PDU. When the Target receives an I PDU with the PNI one less than the current PNI and the last PDU sent was an ATN PDU, the Target is to resend the last non-ATN PDU that it has sent. This is described in section 14.12.3.4 of the NFC Digital Protocol Spec. The digital layer's NFC-DEP code doesn't implement this so add that support. Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com> Tested-by: Thierry Escande <thierry.escande@linux.intel.com> Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Mark A. Greer authored
When an NFC-DEP Initiator times out when waiting for a DEP_RES from the Target, its supposed to send an ATN to the Target. The Target should respond to the ATN with a similar ATN PDU and the Initiator can then resend the last non-ATN PDU that it sent. No more than 'N(retry,atn)' are to be send where 2 <= 'N(retry,atn)' <= 5. If the Initiator had just sent a NACK PDU when the timeout occurred, it is to continue sending NACKs until 'N(retry,nack)' NACKs have been send. This is described in section 14.12.5.6 of the NFC-DEP Digital Protocol Spec. The digital layer's NFC-DEP code doesn't implement this so add that support. The value chosen for 'N(retry,atn)' is 2. Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com> Tested-by: Thierry Escande <thierry.escande@linux.intel.com> Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Mark A. Greer authored
When an NFC-DEP Target receives a NACK PDU with a PNI equal to 1 less than the current PNI, it is supposed to re-send the last PDU. This is implied in section 14.12.5.4 of the NFC Digital Protocol Spec. The digital layer's NFC-DEP code doesn't implement Target-side NACK handing so add it. The last PDU that was sent is saved in the 'nfc_digital_dev' structure's 'saved_skb' member. The skb will have an additional reference taken to ensure that the skb isn't freed when the driver performs a kfree_skb() on the skb. The length of the skb/PDU is also saved so the length can be restored when re-sending the PDU in the skb (the driver will perform an skb_pull() so an skb_push() needs to be done to restore the skb's data pointer/length). Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com> Tested-by: Thierry Escande <thierry.escande@linux.intel.com> Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Mark A. Greer authored
When an NFC-DEP Initiator receives a frame with an incorrect CRC or with a parity error, and the frame is at least 4 bytes long, its supposed to send a NACK to the Target. The Initiator can send up to 'N(retry,nack)' consecutive NACKs where 2 <= 'N(retry,nack)' <= 5. When the limit is exceeded, a PROTOCOL EXCEPTION is raised. Any other type of transmission error is to be ignored and the Initiator should continue waiting for a new frame. This is described in section 14.12.5.4 of the NFC Digital Protocol Spec. The digital layer's NFC-DEP code doesn't implement any of this so add it. This support diverges from the spec in two significant ways: a) NACKs will be sent for ANY error reported by the driver except a timeout. This is done because there is currently no way for the digital layer to distinguish a CRC or parity error from any other type of error reported by the driver. b) All other errors will cause a PROTOCOL EXCEPTION even frames with CRC errors that are less than 4 bytes. The value chosen for 'N(retry,nack)' is 2. Targets do not send NACK PDUs. Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com> Tested-by: Thierry Escande <thierry.escande@linux.intel.com> Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Mark A. Greer authored
When the peer in an NFC-DEP exchange has a packet to send that is larger than the local maximum payload, it sets the 'MI' bit in the 'I' PDU. This indicates that NFC-DEP chaining is to occur. When such a PDU is received, the local side responds with an 'ACK' PDU and this continues until the peer sends an 'I' PDU with the 'MI' bit cleared. This indicates that the chaining sequence is complete and the entire packet has been transferred. Receiving chained PDUs is currently not supported by the digital layer so add that support. When a chaining sequence is initiated by the peer, the digital layer will allocate an skb large enough to hold 8 maximum sized frame payloads. The maximum payload can range from 64 to 254 bytes so 8 * 254 = 2032 seems like a reasonable compromise between potentially wasting memory and constantly reallocating new, larger skbs. Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com> Tested-by: Thierry Escande <thierry.escande@linux.intel.com> Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Mark A. Greer authored
When the NFC-DEP code is given a packet to send that is larger than the peer's maximum payload, its supposed to set the 'MI' bit in the 'I' PDU's Protocol Frame Byte (PFB). Setting this bit indicates that NFC-DEP chaining is to occur. When NFC-DEP chaining is progress, sender 'I' PDUs are acknowledged with 'ACK' PDUs until the last 'I' PDU in the chain (which has the 'MI' bit cleared) is responded to with a normal 'I' PDU. This can occur while in Initiator mode or in Target mode. Sender NFC-DEP chaining is currently not implemented in the digital layer so add that support. Unfortunately, since sending a frame may require writing the CRC to the end of the data, the relevant data part of the original skb must be copied for each intermediate frame. Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com> Tested-by: Thierry Escande <thierry.escande@linux.intel.com> Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Mark A. Greer authored
The maximum payload for NFC-DEP exchanges (i.e., the number of bytes between SoD and EoD) is negotiated using the ATR_REQ, ATR_RES, and PSL_REQ commands. The valid maximum lengths are 64, 128, 192, and 254 bytes. Currently, NFC-DEP code assumes that both sides are always using 254 byte maximums and ignores attempts by the peer to change it. Instead, implement the negotiation code, enforce the local maximum when receiving data from the peer, and don't send payloads that exceed the remote's maximum. The default local maximum is 254 bytes. Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com> Tested-by: Thierry Escande <thierry.escande@linux.intel.com> Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Mark A. Greer authored
NFC-DEP DEP_REQ and DEP_RES exchanges using 'I' and 'ACK/NACK' PDUs have a sequence number called the Packet Number Information (PNI). The PNI is incremented (modulo 4) after every DEP_REQ/ DEP_RES pair and should be verified by the digital layer code. That verification isn't always done, though, so add code to make sure that it is done. Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com> Tested-by: Thierry Escande <thierry.escande@linux.intel.com> Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Mark A. Greer authored
According to chapter 14 of the NFC-DEP Digital Protocol Spec., the NAD byte should never be present in DEP_REQ or DEP_RES frames. However, this is not enforced so add that enforcement code. Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com> Tested-by: Thierry Escande <thierry.escande@linux.intel.com> Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Mark A. Greer authored
When in Target mode, the Initiator specifies whether subsequent DEP_REQ and DEP_RES frames will include a DID byte by the value passed in the ATR_REQ. If the DID value in the ATR_REQ is '0' then no DID byte will be included. If the DID value is between '1' and '14' then a DID byte containing the same value must be included in subsequent DEP_REQ and DEP_RES frames. Any other DID value is invalid. This is specified in sections 14.8.1.2 and 14.8.2.2 of the NFC Digital Protocol Spec. Checking the DID value (if it should be there at all), is not currently supported by the digital layer's NFC-DEP code. Add this support by remembering the DID value in the ATR_REQ, checking the DID value of received DEP_REQ frames (if it should be there at all), and including the remembered DID value in DEP_RES frames when appropriate. Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com> Tested-by: Thierry Escande <thierry.escande@linux.intel.com> Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Mark A. Greer authored
When in Initiator mode, the digital layer's NFC-DEP code always sets the Device ID (DID) value in the ATR_REQ to '0'. This means that subsequent DEP_REQ and DEP_RES frames must never include a DID byte. This is specified in sections 14.8.1.1 and 14.8.2.1 of the NFC Digital Protocol Spec. Currently, the digital layer's NFC-DEP code doesn't enforce this rule so add code to ensure that there is no DID byte in DEP_RES frames. Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com> Tested-by: Thierry Escande <thierry.escande@linux.intel.com> Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Mark A. Greer authored
Rearrange some of the code in digital_in_recv_dep_res() and digital_tg_recv_dep_req() so the initial code looks similar. The real reason is prepare the code for some upcoming patches that require these changes. Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com> Tested-by: Thierry Escande <thierry.escande@linux.intel.com> Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Mark A. Greer authored
When digital_in_send_cmd() or digital_tg_send_cmd() fail, they do not free the skb that was passed to them so the routine that allocated the skb should free it. Currently, there are several routines in the NFC-DEP code that don't do this so make them. Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com> Tested-by: Thierry Escande <thierry.escande@linux.intel.com> Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
- 25 Nov, 2014 8 commits
-
-
Amitkumar Karwar authored
ACK status (0/1) for ACTION frames is informed to cfg80211. We will extend existing logic used for EAPOL frames. The cfg80211 API is different here. Also, we need to explicitly free cloned skb. Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Amitkumar Karwar authored
Firmware notifies the driver through event if EAPOL data packet has been acked or not. We will inform this status to userspace listening on a socket. Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Amitkumar Karwar authored
We had introduced delay main work logic to avoid processing interrupts when Rx pending packet count reaches high threshold. interrupt processing is restarted later when packet count reduces lower threashold. This helped to reduce unnecessary overhead and improve throughput for SD and PCIe chipsets. As there are no interrupts for USB, we will skip this logic for USB chipsets. Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Amitkumar Karwar authored
This patch adds missing endian conversion for beacon size while processing scan response. Reported-by: Daniel Mosquera <daniel.mosquera@ctag.com> Tested-by: Daniel Mosquera <daniel.mosquera@ctag.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Amitkumar Karwar authored
This patch fixes following sparse warnings: drivers/net/wireless/mwifiex/util.c:152:19: warning: cast from restricted __le16 drivers/net/wireless/mwifiex/util.c:152:19: warning: restricted __le16 degrades to integer Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Lorenzo Bianconi authored
Add TPC capability to TX descriptor path. Cap per-packet TX power according to TX power per-rate tables. Currently TPC is supported just by AR9003 based chips Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Lorenzo Bianconi authored
Add TX power per-rate tables for different MIMO modes (e.g STBC) in order to cap the maximum TX power value per-rate in the TX descriptor path. Cap TX power for self generated frames (ACK, RTS/CTS). Currently TPC is supported just by AR9003 based chips Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Arend van Spriel authored
When the driver has sent a join iovar to the firmware it waits for the events to report result of the connection. However, the wpa_supplicant will request a .disconnect() after a timeout. So upon calling .disconnect() the interface state may still be CONNECTING. Clear the CONNECTING bit as well. Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
- 24 Nov, 2014 3 commits
-
-
Andreas Ruprecht authored
In the Makefile for this driver, the wrong Kconfig option is used to trigger the compilation of the object file. This leads to the driver only being included into the kernel when both CONFIG_RTL8821AE and CONFIG_RTL8192AE are set to "y". Signed-off-by: Andreas Ruprecht <rupran@einserver.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Andreas Ruprecht authored
In four of the rtlwifi drivers, the Makefile contains superfluous statements indicating the compilation of the driver as an LKM regardless of the corresponding Kconfig option. If the corresponding option is set to 'y', the build system will then see the object file in obj-m and obj-y, which leads to a compilation as a built-in only. Even though this leads to the desired behavior, the unconditional appearance in obj-m is confusing for someone reading the Makefile. This patch removes the superfluous Makefile statements. Signed-off-by: Andreas Ruprecht <rupran@einserver.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Vivek Natarajan authored
For FCC and JP, in one of the radar patterns, PPB and PRF seems to be interchanged leading to frequent incorrect radar detections. Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-