- 19 Oct, 2022 25 commits
-
-
Alexandru Tachici authored
No need to use more than one SPI transfer for reads. Use only one from now as ADIN1110/2111 does not tolerate CS changes during reads. The BCM2711/2708 SPI controllers worked fine, but the NXP IMX8MM could not keep CS lowered during SPI bursts. This change aims to make the ADIN1110/2111 driver compatible with both SPI controllers, without any loss of bandwidth/other capabilities. Fixes: bc93e19d ("net: ethernet: adi: Add ADIN1110 support") Signed-off-by:
Alexandru Tachici <alexandru.tachici@analog.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Ido Schimmel says: ==================== bridge: A few multicast cleanups Clean up a few issues spotted while working on the bridge multicast code and running its selftests. ==================== Signed-off-by: -
Ido Schimmel authored
Before creating a new MDB entry, br_multicast_new_group() will call br_mdb_ip_get() to see if one exists and return it if so. Therefore, simply call br_multicast_new_group() and omit the call to br_mdb_ip_get(). Signed-off-by:
Ido Schimmel <idosch@nvidia.com> Acked-by:
Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by:
-
Ido Schimmel authored
IGMPv3 / MLDv2 Membership Reports are only processed from the data path with softIRQ disabled, so there is no need to call spin_lock_bh(). Use spin_lock() instead. This is consistent with how other IGMP / MLD packets are processed. Signed-off-by:
-
Ido Schimmel authored
The test group address is added and removed in v2reportleave_test(). There is no need to delete it again during cleanup as it results in the following error message: # bash -x ./bridge_igmp.sh [...] + cleanup + pre_cleanup [...] + ip address del dev swp4 239.10.10.10/32 RTNETLINK answers: Cannot assign requested address + h2_destroy Solve by removing the unnecessary address deletion. Signed-off-by:
-
Ido Schimmel authored
The qdiscs are added during setup, but not deleted during cleanup, resulting in the following error messages: # ./bridge_vlan_mcast.sh [...] # ./bridge_vlan_mcast.sh Error: Exclusivity flag on, cannot modify. Error: Exclusivity flag on, cannot modify. Solve by deleting the qdiscs during cleanup. Signed-off-by:
-
David S. Miller authored
Sean Anderson says: ==================== net: dpaa: Convert to phylink This series converts the DPAA driver to phylink. I have tried to maintain backwards compatibility with existing device trees whereever possible. However, one area where I was unable to achieve this was with QSGMII. Please refer to patch 2 for details. All mac drivers have now been converted. I would greatly appreciate if anyone has T-series or P-series boards they can test/debug this series on. I only have an LS1046ARDB. Everything but QSGMII should work without breakage; QSGMII needs patches 7 and 8. For this reason, the last 4 patches in this series should be applied together (and should not go through separate trees). Changes in v7: - provide phylink_validate_mask_caps() helper - Fix oops if memac_pcs_create returned -EPROBE_DEFER - Fix using pcs-names instead of pcs-handle-names - Fix not checking for -ENODATA when looking for sgmii pcs - Fix 81-character line - Simplify memac_validate with phylink_validate_mask_caps Changes in v6: - Remove unnecessary $ref from renesas,rzn1-a5psw - Remove unnecessary type from pcs-handle-names - Add maxItems to pcs-handle - Fix 81-character line - Fix uninitialized variable in dtsec_mac_config Changes in v5: - Add Lynx PCS binding Changes in v4: - Use pcs-handle-names instead of pcs-names, as discussed - Don't fail if phy support was not compiled in - Split off rate adaptation series - Split off DPAA "preparation" series - Split off Lynx 10G support - t208x: Mark MAC1 and MAC2 as 10G - Add XFI PCS for t208x MAC1/MAC2 Changes in v3: - Expand pcs-handle to an array - Add vendor prefix 'fsl,' to rgmii and mii properties. - Set maxItems for pcs-names - Remove phy-* properties from example because dt-schema complains and I can't be bothered to figure out how to make it work. - Add pcs-handle as a preferred version of pcsphy-handle - Deprecate pcsphy-handle - Remove mii/rmii properties - Put the PCS mdiodev only after we are done with it (since the PCS does not perform a get itself). - Remove _return label from memac_initialization in favor of returning directly - Fix grabbing the default PCS not checking for -ENODATA from of_property_match_string - Set DTSEC_ECNTRL_R100M in dtsec_link_up instead of dtsec_mac_config - Remove rmii/mii properties - Replace 1000Base... with 1000BASE... to match IEEE capitalization - Add compatibles for QSGMII PCSs - Split arm and powerpcs dts updates Changes in v2: - Better document how we select which PCS to use in the default case - Move PCS_LYNX dependency to fman Kconfig - Remove unused variable slow_10g_if - Restrict valid link modes based on the phy interface. This is easier to set up, and mostly captures what I intended to do the first time. We now have a custom validate which restricts half-duplex for some SoCs for RGMII, but generally just uses the default phylink validate. - Configure the SerDes in enable/disable - Properly implement all ethtool ops and ioctls. These were mostly stubbed out just enough to compile last time. - Convert 10GEC and dTSEC as well - Fix capitalization of mEMAC in commit messages - Add nodes for QSGMII PCSs - Add nodes for QSGMII PCSs ==================== Signed-off-by: -
Sean Anderson authored
Now that we actually read registers from QSGMII PCSs, it's important that we have the correct address (instead of hoping that we're the MAC with all the QSGMII PCSs on its bus). This adds nodes for the QSGMII PCSs. The exact mapping of QSGMII to MACs depends on the SoC. Since the first QSGMII PCSs share an address with the SGMII and XFI PCSs, we only add new nodes for PCSs 2-4. This avoids address conflicts on the bus. Signed-off-by:
Sean Anderson <sean.anderson@seco.com> Signed-off-by:
-
Sean Anderson authored
Now that we actually read registers from QSGMII PCSs, it's important that we have the correct address (instead of hoping that we're the MAC with all the QSGMII PCSs on its bus). This adds nodes for the QSGMII PCSs. They have the same addresses on all SoCs (e.g. if QSGMIIA is present it's used for MACs 1 through 4). Since the first QSGMII PCSs share an address with the SGMII and XFI PCSs, we only add new nodes for PCSs 2-4. This avoids address conflicts on the bus. Signed-off-by:
-
Sean Anderson authored
On the T208X SoCs, MAC1 and MAC2 support XGMII. Add some new MAC dtsi fragments, and mark the QMAN ports as 10G. Fixes: da414bb9 ("powerpc/mpc85xx: Add FSL QorIQ DPAA FMan support to the SoC device tree(s)") Signed-off-by:
-
Sean Anderson authored
This converts DPAA to phylink. All macs are converted. This should work with no device tree modifications (including those made in this series), except for QSGMII (as noted previously). The mEMAC configuration is one of the tricker areas. I have tried to capture all the restrictions across the various models. Most of the time, we assume that if the serdes supports a mode or the phy-interface-mode specifies it, then we support it. The only place we can't do this is (RG)MII, since there's no serdes. In that case, we rely on a (new) devicetree property. There are also several cases where half-duplex is broken. Unfortunately, only a single compatible is used for the MAC, so we have to use the board compatible instead. The 10GEC conversion is very straightforward, since it only supports XAUI. There is generally nothing to configure. The dTSEC conversion is broadly similar to mEMAC, but is simpler because we don't support configuring the SerDes (though this can be easily added) and we don't have multiple PCSs. From what I can tell, there's nothing different in the driver or documentation between SGMII and 1000BASE-X except for the advertising. Similarly, I couldn't find anything about 2500BASE-X. In both cases, I treat them like SGMII. These modes aren't used by any in-tree boards. Similarly, despite being mentioned in the driver, I couldn't find any documented SoCs which supported QSGMII. I have left it unimplemented for now. Signed-off-by:
-
Sean Anderson authored
Although not stated in the datasheet, as far as I can tell PCS for mEMACs is a "Lynx." By reusing the existing driver, we can remove the PCS management code from the memac driver. This requires calling some PCS functions manually which phylink would usually do for us, but we will let it do that soon. One problem is that we don't actually have a PCS for QSGMII. We pretend that each mEMAC's MDIO bus has four QSGMII PCSs, but this is not the case. Only the "base" mEMAC's MDIO bus has the four QSGMII PCSs. This is not an issue yet, because we never get the PCS state. However, it will be once the conversion to phylink is complete, since the links will appear to never come up. To get around this, we allow specifying multiple PCSs in pcsphy. This breaks backwards compatibility with old device trees, but only for QSGMII. IMO this is the only reasonable way to figure out what the actual QSGMII PCS is. Additionally, we now also support a separate XFI PCS. This can allow the SerDes driver to set different addresses for the SGMII and XFI PCSs so they can be accessed at the same time. Signed-off-by:
-
Sean Anderson authored
This adds support for using a serdes which has to be configured. This is primarly in preparation for phylink conversion, which will then change the serdes mode dynamically. Signed-off-by:
-
Russell King (Oracle) authored
Provide a helper that restricts the link modes according to the phylink capabilities. Signed-off-by:
Russell King (Oracle) <rmk+kernel@armlinux.org.uk> [rebased on net-next/master and added documentation] Signed-off-by:
-
Sean Anderson authored
At the moment, mEMACs are configured almost completely based on the phy-connection-type. That is, if the phy interface is RGMII, it assumed that RGMII is supported. For some interfaces, it is assumed that the RCW/bootloader has set up the SerDes properly. This is generally OK, but restricts runtime reconfiguration. The actual link state is never reported. To address these shortcomings, the driver will need additional information. First, it needs to know how to access the PCS/PMAs (in order to configure them and get the link status). The SGMII PCS/PMA is the only currently-described PCS/PMA. Add the XFI and QSGMII PCS/PMAs as well. The XFI (and 10GBASE-KR) PCS/PMA is a c45 "phy" which sits on the same MDIO bus as SGMII PCS/PMA. By default they will have conflicting addresses, but they are also not enabled at the same time by default. Therefore, we can let the XFI PCS/PMA be the default when phy-connection-type is xgmii. This will allow for backwards-compatibility. QSGMII, however, cannot work with the current binding. This is because the QSGMII PCS/PMAs are only present on one MAC's MDIO bus. At the moment this is worked around by having every MAC write to the PCS/PMA addresses (without checking if they are present). This only works if each MAC has the same configuration, and only if we don't need to know the status. Because the QSGMII PCS/PMA will typically be located on a different MDIO bus than the MAC's SGMII PCS/PMA, there is no fallback for the QSGMII PCS/PMA. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Sean Anderson authored
This binding is fairly bare-bones for now, since the Lynx driver doesn't parse any properties (or match based on the compatible). We just need it in order to prevent the PCS nodes from having phy devices attached to them. This is not really a problem, but it is a bit inefficient. This binding is really for three separate PCSs (SGMII, QSGMII, and XFI). However, the driver treats all of them the same. This works because the SGMII and XFI devices typically use the same address, and the SerDes driver (or RCW) muxes between them. The QSGMII PCSs have the same register layout as the SGMII PCSs. To do things properly, we'd probably do something like ethernet-pcs@0 { #pcs-cells = <1>; compatible = "fsl,lynx-pcs"; reg = <0>, <1>, <2>, <3>; }; but that would add complexity, and we can describe the hardware just fine using separate PCSs for now. Signed-off-by: -
Sean Anderson authored
This allows multiple phandles to be specified for pcs-handle, such as when multiple PCSs are present for a single MAC. To differentiate between them, also add a pcs-handle-names property. Signed-off-by:
-
David S. Miller authored
Michał Grzelak says: ==================== net: further improvements to marvell,pp2.yaml This patchset addresses problems with reg ranges and additional $refs. It also limits phy-mode and aligns examples. Best regards, Michał --- Changelog: v4->v5 - drop '+' from all patternProperties - restrict range of patternProperties to [0-2] in top level - drop the $ref in patternProperties:'^...':properties:reg - add patternProperties:'^...':properties:reg:maximum:2 - drop $ref in patternProperties:'^...':properties:phys - add patternProperties:'^...':properties:phys:maxItems:1 - limit phy-mode to the subset found in dts files - reflect the order of subnodes' properties in subnodes' required: - restrict range of pattern to [0-2] in marvell,armada-7k-pp22 case - restrict range of pattern to [0-1] in marvell,armada-375-pp2 case - align to 4 spaces all examples: - add specified maximum to allOf:if:then-else:properties:reg v3->v4 - change commit message of first patch - move allOf:$ref to patternProperties:'^...':$ref - deprecate port-id in favour of reg - move reg to front of properties list in patternProperties - reflect the order of properties in required list in patternProperties - add unevaluatedProperties: false to patternProperties - change unevaluated- to additionalProperties at top level - add property phys: to ports subnode - extend example binding with additional information about phys and sfp - hook phys property to phy-consumer.yaml schema v2->v3 - move 'reg:description' to 'allOf:if:then' - change '#size-cells: true' and '#address-cells: true' to '#size-cells: const: 0' and '#address-cells: const: 1' - replace all occurences of pattern "^eth\{hex_num}*" with "^(ethernet-)?port@[0-9]+$" - add description in 'patternProperties:^...' - add 'patternProperties:^...:interrupt-names:minItems: 1' - add 'patternProperties:^...:reg:description' - update 'patternProperties:^...:port-id:description' - add 'patternProperties:^...:required: - reg' - update '*:description:' to uppercase - add 'allOf:then:required:marvell,system-controller' - skip quotation marks from 'allOf:$ref' - add 'else' schema to match 'allOf:if:then' - restrict 'clocks' in 'allOf:if:then' - restrict 'clock-names' in 'allOf:if:then' - add #address-cells=<1>; #size-cells=<0>; in 'examples:' - change every "ethX" to "ethernet-port@X" in 'examples:' - add "reg" and comment in all ports in 'examples:' - change /ethernet/eth0/phy-mode in examples://Armada-375 to "rgmii-id" - replace each cpm_ with cp0_ in 'examples:' - replace each _syscon0 with _clk0 in 'examples:' - remove each eth0X label in 'examples:' - update armada-375.dtsi and armada-cp11x.dtsi to match marvell,pp2.yaml v1->v2 - move 'properties' to the front of the file - remove blank line after 'properties' - move 'compatible' to the front of 'properties' - move 'clocks', 'clock-names' and 'reg' definitions to 'properties' - substitute all occurences of 'marvell,armada-7k-pp2' with 'marvell,armada-7k-pp22' - add properties:#size-cells and properties:#address-cells - specify list in 'interrupt-names' - remove blank lines after 'patternProperties' - remove '^interrupt' and '^#.*-cells$' patterns - remove blank line after 'allOf' - remove first 'if-then-else' block from 'allOf' - negate the condition in allOf:if schema - delete 'interrupt-controller' from section 'examples' - delete '#interrupt-cells' from section 'examples' ==================== Signed-off-by: -
Marcin Wojtas authored
Update the PP2 ethernet ports subnodes' names to match schema enforced by the marvell,pp2.yaml contents. Add new required properties ('reg') which contains information about the port ID, keeping 'port-id' ones for backward compatibility. Signed-off-by:Marcin Wojtas <mw@semihalf.com> Signed-off-by:
-
Marcin Wojtas authored
Update the PP2 ethernet ports subnodes' names to match schema enforced by the marvell,pp2.yaml contents. Add new required properties ('reg') which contains information about the port ID, keeping 'port-id' ones for backward compatibility. Signed-off-by: -
Michał Grzelak authored
Convert the marvell,pp2 bindings from text to proper schema. Move 'marvell,system-controller' and 'dma-coherent' properties from port up to the controller node, to match what is actually done in DT. Rename all subnodes to match "^(ethernet-)?port@[0-2]$" and deprecate port-id in favour of 'reg'. Signed-off-by:
Michał Grzelak <mig@semihalf.com> Reviewed-by:
-
Govindarajulu Varadarajan authored
Use macro instead of function calls. These values are constant and will not change. Signed-off-by:
Govindarajulu Varadarajan <govind.varadar@gmail.com> Link: https://lore.kernel.org/r/20221018005804.188643-1-govind.varadar@gmail.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Shenwei Wang authored
Removed those unused functions since we simplified the driver by using the page pool to manage RX buffers. Signed-off-by:
Shenwei Wang <shenwei.wang@nxp.com> Link: https://lore.kernel.org/r/20221017161236.1563975-1-shenwei.wang@nxp.comSigned-off-by:
-
Arnd Bergmann authored
This driver was used on Arm and SH machines until 2009, when the last platforms moved to the smsc911x driver for the same hardware. Time to retire this version. Link: https://lore.kernel.org/netdev/1232010482-3744-1-git-send-email-steve.glendinning@smsc.com/Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20221017121900.3520108-1-arnd@kernel.orgSigned-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-nextJakub Kicinski authored
Daniel Borkmann says: ==================== pull-request: bpf-next 2022-10-18 We've added 33 non-merge commits during the last 14 day(s) which contain a total of 31 files changed, 874 insertions(+), 538 deletions(-). The main changes are: 1) Add RCU grace period chaining to BPF to wait for the completion of access from both sleepable and non-sleepable BPF programs, from Hou Tao & Paul E. McKenney. 2) Improve helper UAPI by explicitly defining BPF_FUNC_xxx integer values. In the wild we have seen OS vendors doing buggy backports where helper call numbers mismatched. This is an attempt to make backports more foolproof, from Andrii Nakryiko. 3) Add libbpf *_opts API-variants for bpf_*_get_fd_by_id() functions, from Roberto Sassu. 4) Fix libbpf's BTF dumper for structs with padding-only fields, from Eduard Zingerman. 5) Fix various libbpf bugs which have been found from fuzzing with malformed BPF object files, from Shung-Hsi Yu. 6) Clean up an unneeded check on existence of SSE2 in BPF x86-64 JIT, from Jie Meng. 7) Fix various ASAN bugs in both libbpf and selftests when running the BPF selftest suite on arm64, from Xu Kuohai. 8) Fix missing bpf_iter_vma_offset__destroy() call in BPF iter selftest and use in-skeleton link pointer to remove an explicit bpf_link__destroy(), from Jiri Olsa. 9) Fix BPF CI breakage by pointing to iptables-legacy instead of relying on symlinked iptables which got upgraded to iptables-nft, from Martin KaFai Lau. 10) Minor BPF selftest improvements all over the place, from various others. * tag 'for-netdev' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (33 commits) bpf/docs: Update README for most recent vmtest.sh bpf: Use rcu_trace_implies_rcu_gp() for program array freeing bpf: Use rcu_trace_implies_rcu_gp() in local storage map bpf: Use rcu_trace_implies_rcu_gp() in bpf memory allocator rcu-tasks: Provide rcu_trace_implies_rcu_gp() selftests/bpf: Use sys_pidfd_open() helper when possible libbpf: Fix null-pointer dereference in find_prog_by_sec_insn() libbpf: Deal with section with no data gracefully libbpf: Use elf_getshdrnum() instead of e_shnum selftest/bpf: Fix error usage of ASSERT_OK in xdp_adjust_tail.c selftests/bpf: Fix error failure of case test_xdp_adjust_tail_grow selftest/bpf: Fix memory leak in kprobe_multi_test selftests/bpf: Fix memory leak caused by not destroying skeleton libbpf: Fix memory leak in parse_usdt_arg() libbpf: Fix use-after-free in btf_dump_name_dups selftests/bpf: S/iptables/iptables-legacy/ in the bpf_nf and xdp_synproxy test selftests/bpf: Alphabetize DENYLISTs selftests/bpf: Add tests for _opts variants of bpf_*_get_fd_by_id() libbpf: Introduce bpf_link_get_fd_by_id_opts() libbpf: Introduce bpf_btf_get_fd_by_id_opts() ... ==================== Link: https://lore.kernel.org/r/20221018210631.11211-1-daniel@iogearbox.netSigned-off-by:
-
- 18 Oct, 2022 7 commits
-
-
Daniel Müller authored
Since commit 40b09653 ("selftests/bpf: Adjust vmtest.sh to use local kernel configuration") the vmtest.sh script no longer downloads a kernel configuration but uses the local, in-repository one. This change updates the README, which still mentions the old behavior. Signed-off-by:
Daniel Müller <deso@posteo.net> Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20221017232458.1272762-1-deso@posteo.net
-
Alexei Starovoitov authored
Hou Tao says: ==================== Now bpf uses RCU grace period chaining to wait for the completion of access from both sleepable and non-sleepable bpf program: calling call_rcu_tasks_trace() firstly to wait for a RCU-tasks-trace grace period, then in its callback calls call_rcu() or kfree_rcu() to wait for a normal RCU grace period. According to the implementation of RCU Tasks Trace, it inovkes ->postscan_func() to wait for one RCU-tasks-trace grace period and rcu_tasks_trace_postscan() inovkes synchronize_rcu() to wait for one normal RCU grace period in turn, so one RCU-tasks-trace grace period will imply one normal RCU grace period. To codify the implication, introduces rcu_trace_implies_rcu_gp() in patch #1. And using it in patch Other two uses of call_rcu_tasks_trace() are unchanged: for __bpf_prog_put_rcu() there is no gp chain and for __bpf_tramp_image_put_rcu_tasks() it chains RCU tasks trace GP and RCU tasks GP. An alternative way to remove these unnecessary RCU grace period chainings is using the RCU polling API to check whether or not a normal RCU grace period has passed (e.g. get_state_synchronize_rcu()). But it needs an unsigned long space for each free element or each call, and it is not affordable for local storage element, so as for now always rcu_trace_implies_rcu_gp(). Comments are always welcome. Change Log: v2: * codify the implication of RCU Tasks Trace grace period instead of assuming for it v1: https://lore.kernel.org/bpf/20221011071128.3470622-1-houtao@huaweicloud.com Hou Tao (3): bpf: Use rcu_trace_implies_rcu_gp() in bpf memory allocator bpf: Use rcu_trace_implies_rcu_gp() in local storage map bpf: Use rcu_trace_implies_rcu_gp() for program array freeing ==================== Reviewed-by:
Paul E. McKenney <paulmck@kernel.org> Signed-off-by:
Alexei Starovoitov <ast@kernel.org>
-
Hou Tao authored
To support both sleepable and normal uprobe bpf program, the freeing of trace program array chains a RCU-tasks-trace grace period and a normal RCU grace period one after the other. With the introduction of rcu_trace_implies_rcu_gp(), __bpf_prog_array_free_sleepable_cb() can check whether or not a normal RCU grace period has also passed after a RCU-tasks-trace grace period has passed. If it is true, it is safe to invoke kfree() directly. Signed-off-by:
Hou Tao <houtao1@huawei.com> Link: https://lore.kernel.org/r/20221014113946.965131-5-houtao@huaweicloud.comSigned-off-by:
-
Hou Tao authored
Local storage map is accessible for both sleepable and non-sleepable bpf program, and its memory is freed by using both call_rcu_tasks_trace() and kfree_rcu() to wait for both RCU-tasks-trace grace period and RCU grace period to pass. With the introduction of rcu_trace_implies_rcu_gp(), both bpf_selem_free_rcu() and bpf_local_storage_free_rcu() can check whether or not a normal RCU grace period has also passed after a RCU-tasks-trace grace period has passed. If it is true, it is safe to call kfree() directly. Signed-off-by:
-
Hou Tao authored
The memory free logic in bpf memory allocator chains a RCU Tasks Trace grace period and a normal RCU grace period one after the other, so it can ensure that both sleepable and non-sleepable programs have finished. With the introduction of rcu_trace_implies_rcu_gp(), __free_rcu_tasks_trace() can check whether or not a normal RCU grace period has also passed after a RCU Tasks Trace grace period has passed. If it is true, freeing these elements directly, else freeing through call_rcu(). Signed-off-by:
-
Paul E. McKenney authored
As an accident of implementation, an RCU Tasks Trace grace period also acts as an RCU grace period. However, this could change at any time. This commit therefore creates an rcu_trace_implies_rcu_gp() that currently returns true to codify this accident. Code relying on this accident must call this function to verify that this accident is still happening. Reported-by:
Hou Tao <houtao@huaweicloud.com> Signed-off-by:
-
Jiapeng Chong authored
The function ip6gre_tnl_addr_conflict() is defined in the ip6_gre.c file, but not called elsewhere, so delete this unused function. net/ipv6/ip6_gre.c:887:20: warning: unused function 'ip6gre_tnl_addr_conflict'. Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2419Reported-by:
Abaci Robot <abaci@linux.alibaba.com> Signed-off-by:
Jiapeng Chong <jiapeng.chong@linux.alibaba.com> Link: https://lore.kernel.org/r/20221017093540.26806-1-jiapeng.chong@linux.alibaba.comSigned-off-by:
Paolo Abeni <pabeni@redhat.com>
-
- 13 Oct, 2022 8 commits
-
-
Hou Tao authored
SYS_pidfd_open may be undefined for old glibc, so using sys_pidfd_open() helper defined in task_local_storage_helpers.h instead to fix potential build failure. And according to commit 7615d9e1 ("arch: wire-up pidfd_open()"), the syscall number of pidfd_open is always 434 except for alpha architure, so update the definition of __NR_pidfd_open accordingly. Signed-off-by:
Andrii Nakryiko <andrii@kernel.org> Link: https://lore.kernel.org/bpf/20221011071249.3471760-1-houtao@huaweicloud.com
-
Andrii Nakryiko authored
Shung-Hsi Yu says: ==================== Hi, this patch set fixes several fuzzer-reported issues of libbpf when dealing with (malformed) BPF object file: - patch #1 fix out-of-bound heap write reported by oss-fuzz (currently incorrectly marked as fixed) - patch #2 and #3 fix null-pointer dereference found by locally-run fuzzer. v2: - Rebase to bpf-next - Move elf_getshdrnum() closer to where it's result is used in patch #1, as suggested by Andrii - Touch up the comment in bpf_object__elf_collect(), replacing mention of e_shnum with elf_getshdrnum() - Minor wording change in commit message of patch #1 to for better readability - Remove extra note that comes after commit message in patch #1 v1: https://lore.kernel.org/bpf/20221007174816.17536-1-shung-hsi.yu@suse.com/ ==================== Signed-off-by: -
Andrii Nakryiko authored
Xu Kuohai says: ==================== From: Xu Kuohai <xukuohai@huawei.com> This series fixes bugs found by ASAN when running bpf selftests on arm64. v4: - Address Andrii's suggestions v3: https://lore.kernel.org/bpf/5311e154-c2d4-91a5-ccb8-f5adede579ed@huawei.com - Fix error failure of case test_xdp_adjust_tail_grow exposed by this series v2: https://lore.kernel.org/bpf/20221010070454.577433-1-xukuohai@huaweicloud.com - Rebase and fix conflict v1: https://lore.kernel.org/bpf/20221009131830.395569-1-xukuohai@huaweicloud.com ==================== Signed-off-by:
-
Shung-Hsi Yu authored
When there are no program sections, obj->programs is left unallocated, and find_prog_by_sec_insn()'s search lands on &obj->programs[0] == NULL, and will cause null-pointer dereference in the following access to prog->sec_idx. Guard the search with obj->nr_programs similar to what's being done in __bpf_program__iter() to prevent null-pointer access from happening. Fixes: db2b8b06 ("libbpf: Support CO-RE relocations for multi-prog sections") Signed-off-by:
Shung-Hsi Yu <shung-hsi.yu@suse.com> Signed-off-by:
-
Shung-Hsi Yu authored
ELF section data pointer returned by libelf may be NULL (if section has SHT_NOBITS), so null check section data pointer before attempting to copy license and kversion section. Fixes: cb1e5e96 ("bpf tools: Collect version and license from ELF sections") Signed-off-by:
-
Shung-Hsi Yu authored
This commit replace e_shnum with the elf_getshdrnum() helper to fix two oss-fuzz-reported heap-buffer overflow in __bpf_object__open. Both reports are incorrectly marked as fixed and while still being reproducible in the latest libbpf. # clusterfuzz-testcase-minimized-bpf-object-fuzzer-5747922482888704 libbpf: loading object 'fuzz-object' from buffer libbpf: sec_cnt is 0 libbpf: elf: section(1) .data, size 0, link 538976288, flags 2020202020202020, type=2 libbpf: elf: section(2) .data, size 32, link 538976288, flags 202020202020ff20, type=1 ================================================================= ==13==ERROR: AddressSanitizer: heap-buffer-overflow on address 0x6020000000c0 at pc 0x0000005a7b46 bp 0x7ffd12214af0 sp 0x7ffd12214ae8 WRITE of size 4 at 0x6020000000c0 thread T0 SCARINESS: 46 (4-byte-write-heap-buffer-overflow-far-from-bounds) #0 0x5a7b45 in bpf_object__elf_collect /src/libbpf/src/libbpf.c:3414:24 #1 0x5733c0 in bpf_object_open /src/libbpf/src/libbpf.c:7223:16 #2 0x5739fd in bpf_object__open_mem /src/libbpf/src/libbpf.c:7263:20 ... The issue lie in libbpf's direct use of e_shnum field in ELF header as the section header count. Where as libelf implemented an extra logic that, when e_shnum == 0 && e_shoff != 0, will use sh_size member of the initial section header as the real section header count (part of ELF spec to accommodate situation where section header counter is larger than SHN_LORESERVE). The above inconsistency lead to libbpf writing into a zero-entry calloc area. So intead of using e_shnum directly, use the elf_getshdrnum() helper provided by libelf to retrieve the section header counter into sec_cnt. Fixes: 0d6988e1 ("libbpf: Fix section counting logic") Fixes: 25bbbd7a ("libbpf: Remove assumptions about uniqueness of .rodata/.data/.bss maps") Signed-off-by: -
Xu Kuohai authored
xdp_adjust_tail.c calls ASSERT_OK() to check the return value of bpf_prog_test_load(), but the condition is not correct. Fix it. Fixes: 791cad02 ("bpf: selftests: Get rid of CHECK macro in xdp_adjust_tail.c") Signed-off-by:
Xu Kuohai <xukuohai@huawei.com> Signed-off-by:
Martin KaFai Lau <martin.lau@kernel.org> Link: https://lore.kernel.org/bpf/20221011120108.782373-7-xukuohai@huaweicloud.com
-
Xu Kuohai authored
test_xdp_adjust_tail_grow failed with ipv6: test_xdp_adjust_tail_grow:FAIL:ipv6 unexpected error: -28 (errno 28) The reason is that this test case tests ipv4 before ipv6, and when ipv4 test finished, topts.data_size_out was set to 54, which is smaller than the ipv6 output data size 114, so ipv6 test fails with NOSPC error. Fix it by reset topts.data_size_out to sizeof(buf) before testing ipv6. Fixes: 04fcb5f9 ("selftests/bpf: Migrate from bpf_prog_test_run") Signed-off-by:
-
