SM8150 has (at least) two GPU speed bins. With the support added on the
driver side, wire up bin detection in the DTS to restrict lower-quality
SKUs from running at frequencies they were not validated at.

Tested-by: Marijn Suijten <marijn.suijten@somainline.org> # On Sony Xperia 5 (speed bin 0x3)
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230331-topic-konahana_speedbin-v3-4-2dede22dd7f7@linaro.org

Now that there's display support, there is no reason to assume the default
mode for Adreno should be headless. Keep it like that for boards that
previously enabled it, so as not to create regressions though.

Tested-by: Marijn Suijten <marijn.suijten@somainline.org> # On Sony Xperia 5
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230331-topic-konahana_speedbin-v3-3-2dede22dd7f7@linaro.org

Add the initial device tree support for the Reference Design
Platform(RDP) 468 based on IPQ5332 family of SoCs. This patch carries the
support for Console UART, SPI NOR, eMMC.
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323093120.20558-3-quic_kathirav@quicinc.com

The DSI OPP table on SDM630 is used by one DSI0, but on SDM660 is shared
by two nodes (DSI0 and DSI1), thus it should be rather in top-level, not
in DSI0.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407192605.168666-1-krzysztof.kozlowski@linaro.org

Enable the onboard QCA Wi-Fi. HW identifiers for reference:
qmi chip_id 0x320 chip_family 0x4001 board_id 0xff soc_id 0x400e0000

Firmware sources:
/vendor/firmware_mnt/image/wlanmdsp.bin -> qcom/.../wlanmdsp.mbn
/vendor/firmware_mnt/image/bdwlan.bXX [1] -> [2] -> ath10k/.../board-2.bin
[3] -> ath10k/.../firmware-5.bin

Not sure where 3 comes from on the device itself, gotta investigate that..

According to [4], it's called WCN3990_STRAIT.

[1] XX = board_id printed when the file is missing or by your downstream
kernel firmware loader in the dmesg; if XX=ff, use bdwlan.bin

[2] https://github.com/jhugo/linux/blob/5.5rc2_wifi/README
[3] https://github.com/kvalo/ath10k-firmware/blob/master/WCN3990/hw1.0/HL3.1/WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1/firmware-5.bin
[4] https://git.codelinaro.org/clo/la/platform/vendor/qcom-opensource/wlan/qca-wifi-host-cmn/-/blob/LA.VENDOR.1.0.r1-20700-WAIPIO.QSSI13.0/hif/src/hif_hw_version.h#L55Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406-topic-lenovo_features-v2-4-625d7cb4a944@linaro.org

Enable the [AC]DSP and MPSS and specify the firmware paths.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406-topic-lenovo_features-v2-3-625d7cb4a944@linaro.org

Add a node for RMTFS and associate it with MSA and NAV IDs to enable
modem functionality on SM6115.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406-topic-lenovo_features-v2-2-625d7cb4a944@linaro.org

Add a ramoops node to enable retrieving crash logs.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406-topic-lenovo_features-v2-1-625d7cb4a944@linaro.org

Bindings require pin configuration nodes to have the function, even if
it is GPIO:

  msm8916-thwc-ufi001c.dtb: pinctrl@1000000: sim-ctrl-default-state: 'oneOf' conditional failed, one must be fixed:
    'esim-sel-pins', 'sim-en-pins', 'sim-sel-pins' do not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230324202244.744271-1-krzysztof.kozlowski@linaro.org

Add support for UFS ICE by adding the qcom,ice property and the
ICE dedicated devicetree node.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407105029.2274111-7-abel.vesa@linaro.org

Add nodes for remoteproc, smp2p and smsm in preparation
for audio support on this platform.
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407165345.42800-4-a39.skl@gmail.com

Add nodes for remoteproc, smp2p and smsm to make it possible to use
modem functionality on this platform.
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407165345.42800-3-a39.skl@gmail.com

Add nodes for remoteproc, smp2p and smsm to make it possible to use
wifi/bt functionality on this platform.
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407165345.42800-2-a39.skl@gmail.com

Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers.  Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407180655.128771-2-krzysztof.kozlowski@linaro.org

Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers.  Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407180655.128771-1-krzysztof.kozlowski@linaro.org

Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers.  Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.

Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407180045.126952-1-krzysztof.kozlowski@linaro.org

Fix typo in drive-strength property name.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407180710.128815-1-krzysztof.kozlowski@linaro.org

Fix typo in drive-strength property name.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407181541.139349-1-krzysztof.kozlowski@linaro.org

Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers.  Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-10-krzysztof.kozlowski@linaro.org

Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers.  Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-9-krzysztof.kozlowski@linaro.org

Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers.  Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-8-krzysztof.kozlowski@linaro.org

Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers.  Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-7-krzysztof.kozlowski@linaro.org

Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers.  Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-6-krzysztof.kozlowski@linaro.org

Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers.  Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-5-krzysztof.kozlowski@linaro.org

Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers.  Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-4-krzysztof.kozlowski@linaro.org

Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers.  Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-3-krzysztof.kozlowski@linaro.org

Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers.  Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-2-krzysztof.kozlowski@linaro.org

Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers.  Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-1-krzysztof.kozlowski@linaro.org

Add support for the Xiaomi Mi A3 (xiaomi-laurel-sprout). Here's a
summary on what's defined.

- dmesg output to bootloader preconfigured display
- USB
- UFS
- SD card
- SMD RPM regulators
- Volume Up, Down and Power buttons
- Thermistors
Signed-off-by: Lux Aliaga <they@mint.lgbt>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230306170817.3806-7-they@mint.lgbt

Adds a UFS host controller node and its corresponding PHY to
the sm6125 platform.
Signed-off-by: Lux Aliaga <they@mint.lgbt>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230306170817.3806-5-they@mint.lgbt

Add support for the Xiaomi Mi Pad 5 Pro CSOT variant. The CSOT variant
uses China Star Optoelectronics Technology (CSOT) panel based on NT36523
display controller.
Signed-off-by: Jianhua Lu <lujianhua000@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323005925.23179-3-lujianhua000@gmail.com

Add nodes for BOE NT36523 panel found in xiaomi-elish. This panel
is a dual dsi mode panel and the dsi phy type is cphy.
Signed-off-by: Jianhua Lu <lujianhua000@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323005925.23179-2-lujianhua000@gmail.com

There are two panel variants of xiaomi-elish, BOE and CSOT panels.
In order to support both panels, so split elish dts into common dtsi
and elish-boe dts.
Signed-off-by: Jianhua Lu <lujianhua000@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323005925.23179-1-lujianhua000@gmail.com

SC8150 mailbox is compatible with SDM845.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230322174148.810938-12-krzysztof.kozlowski@linaro.org

SC7180 mailbox is compatible with SDM845.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230322174148.810938-11-krzysztof.kozlowski@linaro.org

QCS404 mailbox is compatible with MSM8916.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230322174148.810938-10-krzysztof.kozlowski@linaro.org

SM6125 mailbox is compatible with MSM8994.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230322174148.810938-9-krzysztof.kozlowski@linaro.org

SM6115 mailbox is compatible with MSM8994.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230322174148.810938-8-krzysztof.kozlowski@linaro.org

SDM630 mailbox is compatible with MSM8994.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230322174148.810938-7-krzysztof.kozlowski@linaro.org

MSM8998 mailbox is compatible with MSM8994.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230322174148.810938-6-krzysztof.kozlowski@linaro.org