- 25 Nov, 2022 39 commits
-
-
Paul Kocialkowski authored
Remove the need for local copies of the v4l2 format and add a common helper to prepare a format compatible with the driver, using the relevant v4l2 helpers. Report a raw colorspace for bayer-encoded pixel formats instead of SRGB. Also cleanup the size bound defines while at it. Signed-off-by:
Paul Kocialkowski <paul.kocialkowski@bootlin.com> Acked-by:
Jernej Skrabec <jernej.skrabec@gmail.com> Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@kernel.org>
-
Paul Kocialkowski authored
Continue moving things over to capture in tidy helpers. Also take the occasion to remove the config struct, which is unwelcome redundancy and use the capture helpers instead. The code is only adapted to reflect the removal of the config structure. No functional change intended. Signed-off-by:
-
Paul Kocialkowski authored
Let's just enable the module when we start using it (at stream on) and benefit from runtime pm instead of enabling it at first open. Also reorder the call to v4l2_pipeline_pm_get. Signed-off-by:
-
Paul Kocialkowski authored
Create minimal helpers that split the enable/disable flow, which will make it easier to move control over to the bridge later on. Generally speaking the goal is to move register configuration to the capture code and later split it with the bridge code. Signed-off-by:
-
Paul Kocialkowski authored
Instead of calculating the planar_offset at one point and using it later in a dedicated function, reimplement address configuration with v4l2 format info in the buffer_configure function. Signed-off-by:
-
Paul Kocialkowski authored
Define and export useful helpers to access dimensions and pixel format. Signed-off-by:
-
Paul Kocialkowski authored
This cleans up the register definitions a bit, adds a prefix, remove masks. Registers are now fully defined, some additional fields were added when needed. New format definitions are added for future use. Some fields are wrongly defined (inverted) in Allwinner literature (e.g. field vs frame prefixes), which is quite misleading. They are now corrected to reflect their actual behavior. This should only be a cosmetic commit. No functional change intended. Signed-off-by:
-
Paul Kocialkowski authored
The current implementation requires up to 3 buffers to properly implement page flipping without losing frames: one is configured before the video stream is started, one just after that and page flipping is synchronized to the frame done interrupt. The comment in the code mentions that "CSI will lookup the next dma buffer for next frame before the current frame done IRQ triggered". Based on observations of the CSI unit behavior, it seems that the buffer DMA address is sampled when the frame scan begins (in addition to starting the stream), which corresponds to the vblank interrupt that hits just before the frame-done interrupt of the previous frame. As a result, the address configured at the frame done interrupt is not actually used for the next frame but for the one after that. This proposal changes the page flipping sync point to the vsync interrupt, which allows the DMA address to be sampled for the next frame instead and allows operating with only two buffers. In addition to the change in the sync point, the code is refactored to introduce a notion of state that clarifies tracking of the buffers with tidy functions. Signed-off-by:
-
Paul Kocialkowski authored
In an effort to distinguish between the core csi engine (to be represented as the bridge) and the dma engine (the capture video device), rename the video component to capture, with the appropriate prefix. No functional change intended. [Sakari Ailus: fix wrong variable issue (video -> capture) missed in patch] Signed-off-by:
Maxime Ripard <maxime@cerno.tech> Signed-off-by:
-
Paul Kocialkowski authored
Introduce a bridge v4l2 subdev to prepare for separation between the processing part (bridge) and the dma engine, which is required to properly support ths isp workflow later on. Currently the bridge just manages fwnode mapping to media pads, using an async notifier (which was previously in the main code). The s_stream video op just forwards to the connected v4l2 subdev (sensor or MIPI CSI-2 bridge). The video capture device is now registered after the bridge and attaches to it with a media link. Signed-off-by:
-
Dave Stevenson authored
As noted in the headers for V4L2_SUBDEV_FL_HAS_EVENTS, "controls can send events, thus drivers exposing controls should set this flag". This driver exposes controls, but didn't reflect that it could generate events. Correct this, and add the default event handler functions. Signed-off-by:
Dave Stevenson <dave.stevenson@raspberrypi.com> Reviewed-by:
Jacopo Mondi <jacopo@jmondi.org> Signed-off-by:
-
Dave Stevenson authored
The sensor supports 8 or 10 bit readout modes, but the driver only supported 10 bit. Add 8 bit readout. Signed-off-by:
-
Dave Stevenson authored
Adds register settings for additional modes. Signed-off-by:
-
Dave Stevenson authored
As required by libcamera, add the relevant cropping targets to report which portion of the sensor is being read out in any mode. Signed-off-by:
-
Dave Stevenson authored
There's no reason why HBLANK has to be read-only as it only changes the TIMING_HTS register in the sensor. Remove the READ_ONLY flag, and add the relevant handling for it. The minimum value also varies based on whether continuous clock mode is being used or not, so allow hblank_min to depend on that. Signed-off-by:
-
Dave Stevenson authored
Adds support for V4L2_CID_HFLIP and V4L2_CID_VFLIP to allow flipping the image. The driver previously enabled H & V flips in the register table, therefore the controls default to the same settings to avoid changing the behaviour. Signed-off-by:
-
Dave Stevenson authored
Programming the sensor with TIMING_VTS (aka LPFR) was done when triggered by a change in exposure or gain, but not when V4L2_CID_VBLANK was changed. Dynamic frame rate changes could therefore not be achieved. Separate out programming TIMING_VTS so that it is triggered by set_ctrl(V4L2_CID_VBLANK) Signed-off-by:
-
Dave Stevenson authored
Use v4l2_ctrl_new_fwnode_properties to add V4L2_CID_CAMERA_ORIENTATION and V4L2_CID_CAMERA_SENSOR_ROTATION. Signed-off-by:
-
Dave Stevenson authored
The sensor supports either having the CSI2 clock lane free running, or gated when there is no packet to transmit. The driver only selected gated (non-continuous) clock mode. Add code to allow fwnode to configure whether the clock is gated or free running. Signed-off-by:
-
Dave Stevenson authored
The configured vblank_min setting of 151 (meaning VTS of 720 + 151 = 871) is far higher than the setting that works on the sensor, and there are no obvious restrictions stated in the datasheet. Reduce the vblank_min to allow for faster frame rates. Signed-off-by:
-
Dave Stevenson authored
The calculations from pixel rate, width+hblank, and height+vblank do not give the correct framerate - it's half the speed it should be. The datasheet lists the default for the TIMING_HTS registers (0x380c/d) as being 0x2d8 (728) which is less than the width of the image, so the units clearly can't be pixels. If TIMING_HTS is considered to be units of 2-pixels, then the resulting value of 0x5b0 (1456) makes all the calculations correct. This driver is reporting an HBLANK value of 250, with an image width of 1280, so TIMING_HTS is 1530 (0x5fa) pixels. However it was also setting the register to 0x5fa, thereby not taking into account it being units of 2-pixels. Correct the register value to 0x2fd so that all the timing calculations give the correct results. Signed-off-by:
-
Dave Stevenson authored
The driver currently has multiple assumptions that there is only one supported mode. Convert supported_mode to an array, and fix up all references to correctly look at that array. Signed-off-by:
-
Dave Stevenson authored
The pixel rate is determined by the PLL setup in the common registers, not by the mode specific registers, therefore remove it from the mode definition and define it for all modes. Signed-off-by:
-
Dave Stevenson authored
The format code is independent of mode, and each mode could support both Y10 and Y8, so disassociate the code from the mode. Signed-off-by:
-
Dave Stevenson authored
Currently only one mode is supported, so all registers were dropped in one list. In preparation for adding more modes, split out the common registers from those which configure the mode. Signed-off-by:
-
Dave Stevenson authored
TIMING_VTS (registers 0x380e/f), EXPOSURE (registers 0x3500/1/2), and GAIN (0x3509) are all set from ov9282_update_exp_gain as part of the control handler, therefore they do not need to be in the main list of registers. Remove them. Signed-off-by:
-
Lad Prabhakar authored
Make sure we call ov5645_entity_init_cfg() before registering the subdev to make sure default formats are set up. Suggested-by:
Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Lad Prabhakar authored
Make sure we call the PM functions while s_stream(0) even in case of errors in the code flow. v4l2-core takes care of warning the user so no need to add a warning message in the driver. Suggested-by:
-
Lad Prabhakar authored
Drop empty multiline comment. Signed-off-by:
-
Lad Prabhakar authored
Switch to using runtime PM for power management. Signed-off-by:
-
Lad Prabhakar authored
Convert the simple OV5645 Device Tree binding to json-schema. The previous binding marked the below properties as required which was a driver requirement and not the device requirement so just drop them from the required list during the conversion. - clock-frequency - enable-gpios - reset-gpios Also drop the "clock-names" property as we have a single clock source for the sensor and the driver has been updated to drop the clk referencing by name. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Lad Prabhakar authored
Now that the driver has been updated to drop fetching the clk reference by name we no longer need the clock-names property in the ov5645 sensor node. This is in preparation for removal for clock-names property from the DT binding. Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
-
Lad Prabhakar authored
Now that the driver has been updated to drop fetching the clk reference by name we no longer need the clock-names property in the ov5645 sensor node. This is in preparation for removal for clock-names property from the DT binding. Signed-off-by:
Shawn Guo <shawnguo@kernel.org> Signed-off-by:
-
Lad Prabhakar authored
Now that the driver has been updated to drop fetching the clk reference by name we no longer need the clock-names property in the ov5645 sensor node. This is in preparation for removal for clock-names property from the DT binding. Signed-off-by:
-
Bryan O'Donoghue authored
The Sony imx577 uses the same silicon enabling reference code in the available examples provided as the imx412. Add in compatible strings to enable and differentiate the parts. Cc: sakari.ailus@iki.fi Cc: dave.stevenson@raspberrypi.com Cc: jacopo@jmondi.org Cc: "Paul J. Murphy" <paul.j.murphy@intel.com> Cc: Daniele Alessandrelli <daniele.alessandrelli@intel.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org> Cc: devicetree@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by:
Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by:
-
Bryan O'Donoghue authored
imx412 and imx577 return the same chip-id when interrogated via i2c. I've confirmed this myself by Sakari suggested we should add a new compat which should be reflected in the name of the media entity https://patchwork.kernel.org/project/linux-media/patch/20220607134057.2427663-3-bryan.odonoghue@linaro.org/#24894500 Set up the .data parameter of of_device_id to pass a string which we use to set the media entity name. Once done we can add in imx577 as a compatible chips with the media names reflecting the directed compat string. Cc: sakari.ailus@iki.fi Cc: dave.stevenson@raspberrypi.com Cc: jacopo@jmondi.org Cc: "Paul J. Murphy" <paul.j.murphy@intel.com> Cc: Daniele Alessandrelli <daniele.alessandrelli@intel.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org> Cc: devicetree@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by:
-
Bryan O'Donoghue authored
Add compatible bindings for imx577 which uses the same silicon enabling reference code from Sony in the available examples provided. Cc: sakari.ailus@iki.fi Cc: dave.stevenson@raspberrypi.com Cc: jacopo@jmondi.org Cc: "Paul J. Murphy" <paul.j.murphy@intel.com> Cc: Daniele Alessandrelli <daniele.alessandrelli@intel.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org> Cc: devicetree@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by:
-
Andy Shevchenko authored
Replace custom implementation of the device_match_fwnode(). Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Andy Shevchenko authored
Replace custom implementation of the device_match_fwnode(). Signed-off-by:
-
- 15 Nov, 2022 1 commit
-
-
git://linuxtv.org/hverkuil/media_treeMauro Carvalho Chehab authored
Tag branch * tag 'br-v6.2d' of git://linuxtv.org/hverkuil/media_tree: (35 commits) media: saa7164: remove variable cnt atomisp: fix potential NULL pointer dereferences radio-terratec: Remove variable p media: platform: s5p-mfc: Fix spelling mistake "mmaping" -> "mmapping" media: platform: mtk-mdp3: remove unused VIDEO_MEDIATEK_VPU config media: vivid: remove redundant assignment to variable checksum media: cedrus: h264: Optimize mv col buffer allocation media: cedrus: h265: Associate mv col buffers with buffer media: mediatek: vcodec: fix h264 cavlc bitstream fail media: cedrus: hevc: Fix offset adjustments media: imx-jpeg: Fix Coverity issue in probe media: v4l2-ioctl.c: Unify YCbCr/YUV terms in format descriptions media: atomisp: Fix spelling mistake "mis-match" -> "mismatch" media: c8sectpfe: Add missed header(s) media: adv748x: afe: Select input port when initializing AFE media: vimc: Update device configuration in the documentation media: adv748x: Remove dead function declaration media: mxl5005s: Make array RegAddr static const media: atomisp: Fix spelling mistake "modee" -> "mode" media: meson/vdec: always init coef_node_start ...
-
